Skip to contentSkip to conversation

WD80x3: fix printk() calls to netdev_*() calls

PATCH In review Drew McGowen 2 participants 2 messages Oct 25, 2013 – Oct 29, 2013

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 WD80x3: fix printk() calls to netdev_*() calls

Replace legacy-style printk() calls to use netdev_<level> functions. Also fix version printing to use pr_info_once().

---
 drivers/net/ethernet/8390/wd.c | 31 ++++++++++++++++---------------
 1 file changed, 16 insertions(+), 15 deletions(-)
drivers/net/ethernet/8390/wd.c +16 -15
index 03eb3ee..38d3110 100644
@@ -26,7 +26,7 @@
 */
 
 static const char version[] =
-	"wd.c:v1.10 9/23/94 Donald Becker ([email protected])\n";
+	"wd.c:v1.10 9/23/94 Donald Becker ([email protected])";
 
 #include <linux/module.h>
 #include <linux/kernel.h>
@@ -169,7 +169,6 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 	int ancient = 0;			/* An old card without config registers. */
 	int word16 = 0;				/* 0 = 8 bit, 1 = 16 bit */
 	const char *model_name;
-	static unsigned version_printed;
 
 	for (i = 0; i < 8; i++)
 		checksum += inb(ioaddr + 8 + i);
@@ -180,19 +179,19 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 
 	/* Check for semi-valid mem_start/end values if supplied. */
 	if ((dev->mem_start % 0x2000) || (dev->mem_end % 0x2000)) {
-		printk(KERN_WARNING "wd.c: user supplied mem_start or mem_end not on 8kB boundary - ignored.\n");
+		netdev_warn(dev, "wd.c: user supplied mem_start or mem_end not on 8kB boundary - ignored.\n");
 		dev->mem_start = 0;
 		dev->mem_end = 0;
 	}
 
-	if (ei_debug  &&  version_printed++ == 0)
-		printk(version);
+	if (ei_debug)
+		pr_info_once("%s\n", version);
 
 	for (i = 0; i < 6; i++)
 		dev->dev_addr[i] = inb(ioaddr + 8 + i);
 
-	printk("%s: WD80x3 at %#3x, %pM",
-	       dev->name, ioaddr, dev->dev_addr);
+	netdev_info(dev, "WD80x3 at %#3x, %pM",
+		ioaddr, dev->dev_addr);
 
 	/* The following PureData probe code was contributed by
 	   Mike Jagdis <[email protected]>. Puredata does software
@@ -244,7 +243,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 		}
 #ifndef final_version
 		if ( !ancient && (inb(ioaddr+1) & 0x01) != (word16 & 0x01))
-			printk("\nWD80?3: Bus width conflict, %d (probe) != %d (reg report).",
+			netdev_warn(dev, "\nWD80?3: Bus width conflict, %d (probe) != %d (reg report).",
 				   word16 ? 16 : 8, (inb(ioaddr+1) & 0x01) ? 16 : 8);
 #endif
 	}
@@ -259,7 +258,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 		if (reg0 == 0xff || reg0 == 0) {
 			/* Future plan: this could check a few likely locations first. */
 			dev->mem_start = 0xd0000;
-			printk(" assigning address %#lx", dev->mem_start);
+			pr_cont(" assigning address %#lx", dev->mem_start);
 		} else {
 			int high_addr_bits = inb(ioaddr+WD_CMDREG5) & 0x1f;
 			/* Some boards don't have the register 5 -- it returns 0xff. */
@@ -298,7 +297,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 			outb_p(0x00, nic_addr+EN0_IMR);	/* Mask all intrs. again. */
 
 			if (ei_debug > 2)
-				printk(" autoirq is %d", dev->irq);
+				pr_cont(" autoirq is %d", dev->irq);
 			if (dev->irq < 2)
 				dev->irq = word16 ? 10 : 5;
 		} else
@@ -310,7 +309,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 	   share and the board will usually be enabled. */
 	i = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev);
 	if (i) {
-		printk (" unable to get IRQ %d.\n", dev->irq);
+		pr_cont(" unable to get IRQ %d.\n", dev->irq);
 		return i;
 	}
 
@@ -338,7 +337,7 @@ static int __init wd_probe1(struct net_device *dev, int ioaddr)
 		return -ENOMEM;
 	}
 
-	printk(" %s, IRQ %d, shared memory at %#lx-%#lx.\n",
+	pr_cont(" %s, IRQ %d, shared memory at %#lx-%#lx.\n",
 		   model_name, dev->irq, dev->mem_start, dev->mem_end-1);
 
 	ei_status.reset_8390 = wd_reset_8390;
@@ -387,7 +386,8 @@ wd_reset_8390(struct net_device *dev)
 	int wd_cmd_port = dev->base_addr - WD_NIC_OFFSET; /* WD_CMDREG */
 
 	outb(WD_RESET, wd_cmd_port);
-	if (ei_debug > 1) printk("resetting the WD80x3 t=%lu...", jiffies);
+	if (ei_debug > 1)
+		netdev_dbg(dev, "resetting the WD80x3 t=%lu...", jiffies);
 	ei_status.txing = 0;
 
 	/* Set up the ASIC registers, just in case something changed them. */
@@ -395,7 +395,8 @@ wd_reset_8390(struct net_device *dev)
 	if (ei_status.word16)
 		outb(NIC16 | ((dev->mem_start>>19) & 0x1f), wd_cmd_port+WD_CMDREG5);
 
-	if (ei_debug > 1) printk("reset done\n");
+	if (ei_debug > 1)
+		pr_cont("reset done\n");
 }
 
 /* Grab the 8390 specific header. Similar to the block_input routine, but
@@ -476,7 +477,7 @@ wd_close(struct net_device *dev)
 	int wd_cmdreg = dev->base_addr - WD_NIC_OFFSET; /* WD_CMDREG */
 
 	if (ei_debug > 1)
-		printk("%s: Shutting down ethercard.\n", dev->name);
+		netdev_info(dev, "Shutting down ethercard.\n");
 	ei_close(dev);
 
 	/* Change from 16-bit to 8-bit shared memory so reboot works. */
Signature · 1 line
1.8.1.2
maintainer
#1 lore raw

From: Drew McGowen <[email protected]>
Date: Fri, 25 Oct 2013 21:56:05 +0000

drivers/net/ethernet/8390/wd.c static int __init wd_probe1(struct net_device *dev, int ioaddr) · line 194

Quoted 4 lines
drivers/net/ethernet/8390/wd.c +2 -2
-	printk("%s: WD80x3 at %#3x, %pM",
-	       dev->name, ioaddr, dev->dev_addr);
+	netdev_info(dev, "WD80x3 at %#3x, %pM",
+		ioaddr, dev->dev_addr);

This is incorrect indentation.

On a multi-line function call, the arguments one the second and subsequent lines must start at exactly the first column after the openning parenthesis on the first line.

Everyone who makes this mistake is trying to be lazy and use only TAB characters to indent their code, don't do this. You must use the appropriate number of TAB _and_ SPACE characters necessary to achieve the correct indentation.