Skip to contentSkip to conversation

mac80211_hwsim: Fix tracking of beaconing for multi-vif

PATCH Applied Jouni Malinen 2 participants 2 messages Oct 22, 2013 – Oct 28, 2013 Networking drivers (wireless)

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 mac80211_hwsim: Fix tracking of beaconing for multi-vif

mac80211_hwsim canceled beacon_timer on any vif changing from enabled to disabled beaconing. This breaks cases where there are multiple beaconing vifs and only one of them is removed. Fix this by tracking beaconing status per vif and disable beacon_timer only if no active vif remain with beaconing enabled.

---
 drivers/net/wireless/mac80211_hwsim.c |   27 ++++++++++++++++++++++++---
 1 file changed, 24 insertions(+), 3 deletions(-)
drivers/net/wireless/mac80211_hwsim.c +24 -3
index 2cd3f54..de0df86 100644
@@ -167,6 +167,7 @@ struct hwsim_vif_priv {
 	u32 magic;
 	u8 bssid[ETH_ALEN];
 	bool assoc;
+	bool bcn_en;
 	u16 aid;
 };
 
@@ -1170,6 +1171,16 @@ static void mac80211_hwsim_configure_filter(struct ieee80211_hw *hw,
 	*total_flags = data->rx_filter;
 }
 
+static void mac80211_hwsim_bcn_en_iter(void *data, u8 *mac,
+				       struct ieee80211_vif *vif)
+{
+	unsigned int *count = data;
+	struct hwsim_vif_priv *vp = (void *)vif->drv_priv;
+
+	if (vp->bcn_en)
+		(*count)++;
+}
+
 static void mac80211_hwsim_bss_info_changed(struct ieee80211_hw *hw,
 					    struct ieee80211_vif *vif,
 					    struct ieee80211_bss_conf *info,
@@ -1180,7 +1191,8 @@ static void mac80211_hwsim_bss_info_changed(struct ieee80211_hw *hw,
 
 	hwsim_check_magic(vif);
 
-	wiphy_debug(hw->wiphy, "%s(changed=0x%x)\n", __func__, changed);
+	wiphy_debug(hw->wiphy, "%s(changed=0x%x vif->addr=%pM)\n",
+		    __func__, changed, vif->addr);
 
 	if (changed & BSS_CHANGED_BSSID) {
 		wiphy_debug(hw->wiphy, "%s: BSSID changed: %pM\n",
@@ -1202,6 +1214,7 @@ static void mac80211_hwsim_bss_info_changed(struct ieee80211_hw *hw,
 
 	if (changed & BSS_CHANGED_BEACON_ENABLED) {
 		wiphy_debug(hw->wiphy, "  BCN EN: %d\n", info->enable_beacon);
+		vp->bcn_en = info->enable_beacon;
 		if (data->started &&
 		    !hrtimer_is_queued(&data->beacon_timer.timer) &&
 		    info->enable_beacon) {
@@ -1215,8 +1228,16 @@ static void mac80211_hwsim_bss_info_changed(struct ieee80211_hw *hw,
 			tasklet_hrtimer_start(&data->beacon_timer,
 					      ns_to_ktime(until_tbtt * 1000),
 					      HRTIMER_MODE_REL);
-		} else if (!info->enable_beacon)
-			tasklet_hrtimer_cancel(&data->beacon_timer);
+		} else if (!info->enable_beacon) {
+			unsigned int count = 0;
+			ieee80211_iterate_active_interfaces(
+				data->hw, IEEE80211_IFACE_ITER_NORMAL,
+				mac80211_hwsim_bcn_en_iter, &count);
+			wiphy_debug(hw->wiphy, "  beaconing vifs remaining: %u",
+				    count);
+			if (count == 0)
+				tasklet_hrtimer_cancel(&data->beacon_timer);
+		}
 	}
 
 	if (changed & BSS_CHANGED_ERP_CTS_PROT) {
Signature · 5 lines
1.7.9.5


-- 
Jouni Malinen                                            PGP id EFC895FA
maintainer Applied
#1 lore raw
Quoted 5 lines · Jouni Malinen

mac80211_hwsim canceled beacon_timer on any vif changing from enabled to disabled beaconing. This breaks cases where there are multiple beaconing vifs and only one of them is removed. Fix this by tracking beaconing status per vif and disable beacon_timer only if no active vif remain with beaconing enabled.

Applied.

johannes