Skip to contentSkip to conversation

mmc: sdhci: Workaround Intel Merrifield issue for HS200

PATCH In review David Cohen 3 participants 8 messages Oct 29, 2013 – Jan 13, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover mmc: sdhci: Workaround Intel Merrifield issue for HS200

Hi,

SDHCI used to work well on Intel Merrifield until this patch was applied:

commit 156e14b126ffb6f040bc6f1aff3c51077e42a744

Author: Giuseppe CAVALLARO <[email protected]>
Date:   Wed Jun 12 08:16:38 2013 +0200

mmc: sdhci: fix caps2 for HS200

Although the HC supports HS200 (eMMC) the caps2 are always zero; this means there's no way to use the super speed mode (when init the card).

If the HC support SDR104, for SD3.0, so it also supports HS200 for eMMC and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.

Looks like there is a hw issue with unknown root cause so far.

Is it acceptable to have the quirk I'm proposing to workaround the issue?

Br, David Cohen

---
David Cohen (2):
mmc: sdhci: add quirk for broken HS200 support
mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield

 drivers/mmc/host/sdhci-pci.c | 1 +
 drivers/mmc/host/sdhci.c     | 3 ++-
 include/linux/mmc/sdhci.h    | 2 ++
 3 files changed, 5 insertions(+), 1 deletion(-)
Signature · 1 line
1.8.4.rc3
#1 lore raw

PATCH 1/2 mmc: sdhci: add quirk for broken HS200 support

This patch defines a quirk for platforms unable to enable HS200 support.

---
 drivers/mmc/host/sdhci.c  | 3 ++-
 include/linux/mmc/sdhci.h | 2 ++
 2 files changed, 4 insertions(+), 1 deletion(-)
drivers/mmc/host/sdhci.c +2 -1
index 7a7fb4f..ef91ad4 100644
@@ -3002,7 +3002,8 @@ int sdhci_add_host(struct sdhci_host *host)
 		/* SD3.0: SDR104 is supported so (for eMMC) the caps2
 		 * field can be promoted to support HS200.
 		 */
-		mmc->caps2 |= MMC_CAP2_HS200;
+		if (!(host->quirks2 & SDHCI_QUIRK2_BROKEN_HS200))
+			mmc->caps2 |= MMC_CAP2_HS200;
 	} else if (caps[1] & SDHCI_SUPPORT_SDR50)
 		mmc->caps |= MMC_CAP_UHS_SDR50;
 
include/linux/mmc/sdhci.h +2 -0
index 3e781b8..362927c4 100644
@@ -98,6 +98,8 @@ struct sdhci_host {
 #define SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON		(1<<4)
 /* Controller has a non-standard host control register */
 #define SDHCI_QUIRK2_BROKEN_HOST_CONTROL		(1<<5)
+/* Controller does not support HS200 */
+#define SDHCI_QUIRK2_BROKEN_HS200			(1<<6)
 
 	int irq;		/* Device IRQ */
 	void __iomem *ioaddr;	/* Mapped address */
Signature · 1 line
1.8.4.rc3
#2 lore raw

PATCH 2/2 mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield

In reply to David Cohen

Due to unkown hw issue so far, Merrifield is unable to enable HS200 support. This patch adds quirk to avoid SDHCI to initialize with error below:

[   53.850132] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W
3.12.0-rc6-00037-g3d7c8d9-dirty #36
[   53.850150] Hardware name: Intel Corporation Merrifield/SALT BAY,
BIOS 397 2013.09.12:11.51.40
[   53.850167]  00000000 00000000 ee409e48 c18816d2 00000000 ee409e78
c123e254 c1acc9b0
[   53.850227]  00000000 00000000 c1b14148 000003de c16c03bf c16c03bf
ee75b480 ed97c54c
[   53.850282]  ee75b480 ee409e88 c123e292 00000009 00000000 ee409ef8
c16c03bf c1207fac
[   53.850339] Call Trace:
[   53.850376]  [<c18816d2>] dump_stack+0x4b/0x79
[   53.850408]  [<c123e254>] warn_slowpath_common+0x84/0xa0
[   53.850436]  [<c16c03bf>] ? sdhci_send_command+0xb4f/0xc50
[   53.850462]  [<c16c03bf>] ? sdhci_send_command+0xb4f/0xc50
[   53.850490]  [<c123e292>] warn_slowpath_null+0x22/0x30
[   53.850516]  [<c16c03bf>] sdhci_send_command+0xb4f/0xc50
[   53.850545]  [<c1207fac>] ? native_sched_clock+0x2c/0xb0
[   53.850575]  [<c14c1f93>] ? delay_tsc+0x73/0xb0
[   53.850601]  [<c14c1ebe>] ? __const_udelay+0x1e/0x20
[   53.850626]  [<c16bdeb3>] ? sdhci_reset+0x93/0x190
[   53.850654]  [<c16c05b0>] sdhci_finish_data+0xf0/0x2e0
[   53.850683]  [<c16c130f>] sdhci_irq+0x31f/0x930
[   53.850713]  [<c12cb080>] ? __buffer_unlock_commit+0x10/0x20
[   53.850740]  [<c12cbcd7>] ? trace_buffer_unlock_commit+0x37/0x50
[   53.850773]  [<c1288f3c>] handle_irq_event_percpu+0x5c/0x220
[   53.850800]  [<c128bc96>] ? handle_fasteoi_irq+0x16/0xd0
[   53.850827]  [<c128913a>] handle_irq_event+0x3a/0x60
[   53.850852]  [<c128bc80>] ? unmask_irq+0x30/0x30
[   53.850878]  [<c128bcce>] handle_fasteoi_irq+0x4e/0xd0
[   53.850895]  <IRQ>  [<c1890b52>] ? do_IRQ+0x42/0xb0
[   53.850943]  [<c1890a31>] ? common_interrupt+0x31/0x38
[   53.850973]  [<c12b00d8>] ? cgroup_mkdir+0x4e8/0x580
[   53.851001]  [<c1208d32>] ? default_idle+0x22/0xf0
[   53.851029]  [<c1209576>] ? arch_cpu_idle+0x26/0x30
[   53.851054]  [<c1288505>] ? cpu_startup_entry+0x65/0x240
[   53.851082]  [<c18793d5>] ? rest_init+0xb5/0xc0
[   53.851108]  [<c1879320>] ? __read_lock_failed+0x18/0x18
[   53.851138]  [<c1bf6a15>] ? start_kernel+0x31b/0x321
[   53.851164]  [<c1bf652f>] ? repair_env_string+0x51/0x51
[   53.851190]  [<c1bf6363>] ? i386_start_kernel+0x139/0x13c
[   53.851209] ---[ end trace 92777f5fe48d33f2 ]---
[   53.853449] mmcblk0: error -84 transferring data, sector 11142162, nr
304, cmd response 0x0, card status 0x0
[   53.853476] mmcblk0: retrying using single block read
[   55.937863] sdhci: Timeout waiting for Buffer Read Ready interrupt
during tuning procedure, falling back to fixed sampling clock
[   56.207951] sdhci: Timeout waiting for Buffer Read Ready interrupt
during tuning procedure, falling back to fixed sampling clock
[   66.228785] mmc0: Timeout waiting for hardware interrupt.
[   66.230855] ------------[ cut here ]------------
---
 drivers/mmc/host/sdhci-pci.c | 1 +
 1 file changed, 1 insertion(+)
drivers/mmc/host/sdhci-pci.c +1 -0
index 06f026a..86a7fbb 100644
@@ -376,6 +376,7 @@ static int intel_mrfl_mmc_probe_slot(struct sdhci_pci_slot *slot)
 
 static const struct sdhci_pci_fixes sdhci_intel_mrfl_mmc = {
 	.quirks		= SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
+	.quirks2	= SDHCI_QUIRK2_BROKEN_HS200,
 	.probe_slot	= intel_mrfl_mmc_probe_slot,
 };
 
Signature · 1 line
1.8.4.rc3
#3 lore raw
In reply to David Cohen
Quoted 13 lines · David Cohen

Hi,

SDHCI used to work well on Intel Merrifield until this patch was applied:

commit 156e14b126ffb6f040bc6f1aff3c51077e42a744

Author: Giuseppe CAVALLARO <[email protected]>
Date:   Wed Jun 12 08:16:38 2013 +0200

mmc: sdhci: fix caps2 for HS200

Although the HC supports HS200 (eMMC) the caps2 are always zero; this means there's no way to use the super speed mode (when init the card).

Quoted 6 lines

If the HC support SDR104, for SD3.0, so it also supports HS200 for eMMC and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.

Looks like there is a hw issue with unknown root cause so far.

Is it acceptable to have the quirk I'm proposing to workaround the issue?

Ping. Any comments here?

Br, David Cohen

#4 lore raw
Quoted 20 lines · David Cohen
Quoted 19 lines · David Cohen

Hi,

SDHCI used to work well on Intel Merrifield until this patch was applied:

commit 156e14b126ffb6f040bc6f1aff3c51077e42a744

Author: Giuseppe CAVALLARO <[email protected]>
Date:   Wed Jun 12 08:16:38 2013 +0200

mmc: sdhci: fix caps2 for HS200

Although the HC supports HS200 (eMMC) the caps2 are always zero; this means there's no way to use the super speed mode (when init the
card).

If the HC support SDR104, for SD3.0, so it also supports HS200 for
eMMC
and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.

Quoted 7 lines
Quoted 3 lines

Looks like there is a hw issue with unknown root cause so far.

Is it acceptable to have the quirk I'm proposing to workaround the issue?

Ping. Any comments here?

Chris,
Can you pick this one?
IMX also needs this quirk for imx6q/dl since it can not meet HS200 timing requirement.

David,
Is the unkonwn hw issue in your patch #2 resolved now? If yes, you may not need this quirk.
I could resend it with your sign-off with IMX patches.

Regards
Dong Aisheng

Quoted 7 lines

Br, David Cohen
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#5 lore raw
Quoted 36 lines · Dong Aisheng
Quoted 20 lines · David Cohen
Quoted 19 lines · David Cohen

Hi,

SDHCI used to work well on Intel Merrifield until this patch was applied:

commit 156e14b126ffb6f040bc6f1aff3c51077e42a744

Author: Giuseppe CAVALLARO <[email protected]>
Date:   Wed Jun 12 08:16:38 2013 +0200

mmc: sdhci: fix caps2 for HS200

Although the HC supports HS200 (eMMC) the caps2 are always zero; this means there's no way to use the super speed mode (when init the
card).

If the HC support SDR104, for SD3.0, so it also supports HS200 for
eMMC
and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.

Quoted 7 lines
Quoted 3 lines

Looks like there is a hw issue with unknown root cause so far.

Is it acceptable to have the quirk I'm proposing to workaround the issue?

Ping. Any comments here?

Chris,
Can you pick this one?
IMX also needs this quirk for imx6q/dl since it can not meet HS200 timing requirement.

Quoted 4 lines

David,
Is the unkonwn hw issue in your patch #2 resolved now? If yes, you may not need this quirk.
I could resend it with your sign-off with IMX patches.

Merrifield still needs this quirk to not break MMC support. This quirk could be applied to 3.13-rc (since merrifield was added to sdhci-pci.c on 3.13-rc1).

Br, David

Quoted 11 lines

Regards
Dong Aisheng

Quoted 7 lines

Br, David Cohen
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Acked-by
#6 lore raw
Quoted 37 lines · David Cohen
Quoted 36 lines · Dong Aisheng
Quoted 20 lines · David Cohen
Quoted 19 lines · David Cohen

Hi,

SDHCI used to work well on Intel Merrifield until this patch was applied:

commit 156e14b126ffb6f040bc6f1aff3c51077e42a744

Author: Giuseppe CAVALLARO <[email protected]>
Date:   Wed Jun 12 08:16:38 2013 +0200

mmc: sdhci: fix caps2 for HS200

Although the HC supports HS200 (eMMC) the caps2 are always zero; this means there's no way to use the super speed mode (when init the
card).

If the HC support SDR104, for SD3.0, so it also supports HS200 for
eMMC
and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.

Quoted 7 lines
Quoted 3 lines

Looks like there is a hw issue with unknown root cause so far.

Is it acceptable to have the quirk I'm proposing to workaround the issue?

Ping. Any comments here?

Chris,
Can you pick this one?
IMX also needs this quirk for imx6q/dl since it can not meet HS200 timing requirement.

Quoted 9 lines
Quoted 4 lines

David,
Is the unkonwn hw issue in your patch #2 resolved now? If yes, you may not need this quirk.
I could resend it with your sign-off with IMX patches.

Merrifield still needs this quirk to not break MMC support. This quirk could be applied to 3.13-rc (since merrifield was added to sdhci-pci.c on 3.13-rc1).

Okay, thanks for the information.
So please take my ACK:

I will send IMX patches based on it.

Regards
Dong Aisheng

Quoted 13 lines

Br, David

Quoted 11 lines

Regards
Dong Aisheng

Quoted 7 lines

Br, David Cohen
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in

the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#7 lore raw

Hi David, Dong,

Quoted 9 lines · Dong Aisheng
Quoted 3 lines · David Cohen

Merrifield still needs this quirk to not break MMC support. This quirk could be applied to 3.13-rc (since merrifield was added to sdhci-pci.c on 3.13-rc1).

Okay, thanks for the information.
So please take my ACK:

Thanks, I've pushed this to mmc-next now.

- Chris.

Signature · 1 line
Chris Ball   <[email protected]>   <http://printf.net/>