Skip to contentSkip to conversation

DT: correctly describe GIC400 virtualisation regions

PATCH New Ian Campbell 4 participants 7 messages Nov 1, 2013 – Nov 22, 2013

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover DT: correctly describe GIC400 virtualisation regions

Several existing platforms which sport an A15 compatible GIC to not include the extended GIC cpu interface regisiters in their device tree. Fix these.

Also extend the bindings to cope with cpu intefface registers which are not in contiguous pages.

Ian.

#1 lore raw

PATCH 1/2 arm: correct GIC cpu interface range for Cortex A15/GIC 400

GICv2 (Cortex A15/GIC 400) have CPU interface registers up to offset 0x1004 (the 32-bit GICC_DIR register a 0x1000). The GIC 400 documentation specifies the CPU interface region as being 0x2000 in size.

Update all DTS entries claiming "arm,cortex-a15-gic" compatibility. Of these I only have personal experience with the vexpress a Calxeda (ecx) platforms and annecdotal evidence for omap and exynos. For the others I'm just assuming.

Also update the example a15 binding in the documentation.

The "Texas Instruments Keystone 2 SoC" platform which claim to have an a15 compatible GIC but does not include the GICH/GICV registers. I've not touched that here.

Cc devicetree at vger.kernel.org
Cc linux-arm-kernel at lists.infradead.org
---
 Documentation/devicetree/bindings/arm/gic.txt | 2 +-
 arch/arm/boot/dts/ecx-2000.dts                | 2 +-
 arch/arm/boot/dts/exynos5.dtsi                | 2 +-
 arch/arm/boot/dts/exynos5440.dtsi             | 2 +-
 arch/arm/boot/dts/omap5.dtsi                  | 2 +-
 arch/arm/boot/dts/tegra114.dtsi               | 2 +-
 arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts   | 2 +-
 arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts    | 2 +-
 arch/arm/boot/dts/xenvm-4.2.dts               | 2 +-
 arch/arm64/boot/dts/foundation-v8.dts         | 2 +-
 arch/arm64/boot/dts/rtsm_ve-aemv8a.dts        | 2 +-
 11 files changed, 11 insertions(+), 11 deletions(-)
Documentation/devicetree/bindings/arm/gic.txt +1 -1
index 3dfb0c0..ea215e8 100644
@@ -83,7 +83,7 @@ Example:
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x2c001000 0x1000>,
-		      <0x2c002000 0x1000>,
+		      <0x2c002000 0x2000>,
 		      <0x2c004000 0x2000>,
 		      <0x2c006000 0x2000>;
 		interrupts = <1 9 0xf04>;
arch/arm/boot/dts/ecx-2000.dts +1 -1
index 139b40c..61927de 100644
@@ -93,7 +93,7 @@
 			interrupt-controller;
 			interrupts = <1 9 0xf04>;
 			reg = <0xfff11000 0x1000>,
-			      <0xfff12000 0x1000>,
+			      <0xfff12000 0x2000>,
 			      <0xfff14000 0x2000>,
 			      <0xfff16000 0x2000>;
 		};
arch/arm/boot/dts/exynos5.dtsi +1 -1
index f65e124..c72782f 100644
@@ -44,7 +44,7 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg =	<0x10481000 0x1000>,
-			<0x10482000 0x1000>,
+			<0x10482000 0x2000>,
 			<0x10484000 0x2000>,
 			<0x10486000 0x2000>;
 		interrupts = <1 9 0xf04>;
arch/arm/boot/dts/exynos5440.dtsi +1 -1
index ff7f5d8..19c9636 100644
@@ -31,7 +31,7 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg =	<0x2E1000 0x1000>,
-			<0x2E2000 0x1000>,
+			<0x2E2000 0x2000>,
 			<0x2E4000 0x2000>,
 			<0x2E6000 0x2000>;
 		interrupts = <1 9 0xf04>;
arch/arm/boot/dts/omap5.dtsi +1 -1
index e643620..6c4fe08 100644
@@ -60,7 +60,7 @@
 		interrupt-controller;
 		#interrupt-cells = <3>;
 		reg = <0x48211000 0x1000>,
-		      <0x48212000 0x1000>,
+		      <0x48212000 0x2000>,
 		      <0x48214000 0x2000>,
 		      <0x48216000 0x2000>;
 	};
arch/arm/boot/dts/tegra114.dtsi +1 -1
index abf6c40..eb7a0c4 100644
@@ -20,7 +20,7 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x50041000 0x1000>,
-		      <0x50042000 0x1000>,
+		      <0x50042000 0x2000>,
 		      <0x50044000 0x2000>,
 		      <0x50046000 0x2000>;
 		interrupts = <GIC_PPI 9
arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts +1 -1
index 9420053..f0ec2be 100644
@@ -81,7 +81,7 @@
 		#address-cells = <0>;
 		interrupt-controller;
 		reg = <0 0x2c001000 0 0x1000>,
-		      <0 0x2c002000 0 0x1000>,
+		      <0 0x2c002000 0 0x2000>,
 		      <0 0x2c004000 0 0x2000>,
 		      <0 0x2c006000 0 0x2000>;
 		interrupts = <1 9 0xf04>;
arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts +1 -1
index d2803be..c2db05e 100644
@@ -98,7 +98,7 @@
 		#address-cells = <0>;
 		interrupt-controller;
 		reg = <0 0x2c001000 0 0x1000>,
-		      <0 0x2c002000 0 0x1000>,
+		      <0 0x2c002000 0 0x2000>,
 		      <0 0x2c004000 0 0x2000>,
 		      <0 0x2c006000 0 0x2000>;
 		interrupts = <1 9 0xf04>;
arch/arm/boot/dts/xenvm-4.2.dts +1 -1
index 3369151..92e63eb 100644
@@ -56,7 +56,7 @@
 		#address-cells = <0>;
 		interrupt-controller;
 		reg = <0 0x2c001000 0 0x1000>,
-		      <0 0x2c002000 0 0x100>;
+		      <0 0x2c002000 0 0x2000>;
 	};
 
 	timer {
arch/arm64/boot/dts/foundation-v8.dts +1 -1
index 84fcc50..3e63def 100644
@@ -68,7 +68,7 @@
 		#address-cells = <0>;
 		interrupt-controller;
 		reg = <0x0 0x2c001000 0 0x1000>,
-		      <0x0 0x2c002000 0 0x1000>,
+		      <0x0 0x2c002000 0 0x2000>,
 		      <0x0 0x2c004000 0 0x2000>,
 		      <0x0 0x2c006000 0 0x2000>;
 		interrupts = <1 9 0xf04>;
arch/arm64/boot/dts/rtsm_ve-aemv8a.dts +1 -1
index 572005e..0d271ce 100644
@@ -73,7 +73,7 @@
 		#address-cells = <0>;
 		interrupt-controller;
 		reg = <0x0 0x2c001000 0 0x1000>,
-		      <0x0 0x2c002000 0 0x1000>,
+		      <0x0 0x2c002000 0 0x2000>,
 		      <0x0 0x2c004000 0 0x2000>,
 		      <0x0 0x2c006000 0 0x2000>;
 		interrupts = <1 9 0xf04>;
Signature · 1 line
1.8.4.rc3
#2 lore raw

PATCH 1/2 arm: correct GIC cpu interface range for Cortex A15/GIC 400

Quoted 10 lines · Ian Campbell

GICv2 (Cortex A15/GIC 400) have CPU interface registers up to offset 0x1004 (the 32-bit GICC_DIR register a 0x1000). The GIC 400 documentation specifies the CPU interface region as being 0x2000 in size.

Update all DTS entries claiming "arm,cortex-a15-gic" compatibility. Of these I only have personal experience with the vexpress a Calxeda (ecx) platforms and annecdotal evidence for omap and exynos. For the others I'm just assuming.

Also update the example a15 binding in the documentation.

Quoted 7 lines

The "Texas Instruments Keystone 2 SoC" platform which claim to have an a15 compatible GIC but does not include the GICH/GICV registers. I've not touched that here.

Cc devicetree at vger.kernel.org
Cc linux-arm-kernel at lists.infradead.org
#3 lore raw

PATCH 2/2 arm: Support for platforms with split GIC cpu interface registers.

In reply to Ian Campbell

At least one platform (APM Storm) places the two pages of the GIC cpu interface (and the vcpu side) at non-contiguous locations. Document two additional regions to cover this split and update the corresponding dtsi. Note that Linux (including KVM) does not use any registers in the second page so there is no associated code change here. Xen will use these new regions, although I've not written the corresponding code yet.

The ordering of these new regs is slightly counter intuitive but is inteded to be backward compatible. It is also assumed that all such systems will implement the GIC virtualisation extensions.

Add comments to all of the reg examples to help clarify what is going on.

Cc devicetree at vger.kernel.org
Cc linux-arm-kernel at lists.infradead.org
Cc Kumar Sankaran <[email protected]>
Cc Loc Ho <[email protected]>
Cc Feng Kan <[email protected]>
---
 Documentation/devicetree/bindings/arm/gic.txt | 57 +++++++++++++++++++++------
 arch/arm64/boot/dts/apm-storm.dtsi            |  6 ++-
 2 files changed, 50 insertions(+), 13 deletions(-)
Documentation/devicetree/bindings/arm/gic.txt +46 -11
index ea215e8..00836d9 100644
@@ -38,7 +38,8 @@ Main node required properties:
 
 - reg : Specifies base physical address(s) and size of the GIC registers. The
   first region is the GIC distributor register base and size. The 2nd region is
-  the GIC cpu interface register base and size.
+  the GIC cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 Optional
 - interrupts	: Interrupt source of the parent interrupt controller on
@@ -56,8 +57,8 @@ Example:
 		#interrupt-cells = <3>;
 		#address-cells = <1>;
 		interrupt-controller;
-		reg = <0xfff11000 0x1000>,
-		      <0xfff10100 0x100>;
+		reg = <0xfff11000 0x1000>,      /* GIC Dist */
+		      <0xfff10100 0x100>;       /* GIC CPU */
 	};
 
 
@@ -70,9 +71,11 @@ primary interrupt controller).
 Required properties:
 
 - reg : Additional regions specifying the base physical address and
-  size of the VGIC registers. The first additional region is the GIC
-  virtual interface control register base and size. The 2nd additional
-  region is the GIC virtual cpu interface register base and size.
+  size of the VGIC registers. The first additional region (i.e. third
+  overall) is the GIC virtual interface control register base and
+  size. The 2nd additional region (i.e. forth overall) is the GIC
+  virtual cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 - interrupts : VGIC maintenance interrupt.
 
@@ -82,9 +85,41 @@ Example:
 		compatible = "arm,cortex-a15-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
-		reg = <0x2c001000 0x1000>,
-		      <0x2c002000 0x2000>,
-		      <0x2c004000 0x2000>,
-		      <0x2c006000 0x2000>;
-		interrupts = <1 9 0xf04>;
+		reg = <0x2c001000 0x1000>,      /* GIC Dist */
+		      <0x2c002000 0x2000>,      /* GIC CPU */
+		      <0x2c004000 0x2000>,      /* GIC VCPU Control */
+		      <0x2c006000 0x2000>;      /* GIC VCPU1 */
+		interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
+	};
+
+* Split GIC cpu interface
+
+  The cpu interfaces (bare-metal in region 2 and virtual in region 4)
+  may be spread over two pages, with the GICC_DIR (Deactivate
+  Interrupt Register) register falling at the start of the second
+  page. If these pages are contiguous then this is described via the
+  size of the second and fourth entries as described above
+  (e.g. 0x2000 rather than 0x1000).
+
+  However if the two pages are not contiguous then two additional
+  regions are present (5th and 6th) describing the location of the the
+  second half of the GIC cpu interface and GIC virtual cpu interface
+  respectively.
+
+  It is assumed that all such systems will implement the GIC
+  virtualisation extensions.
+
+Example:
+
+	gic: interrupt-controller at 78010000 {
+		compatible = "arm,cortex-a15-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x78010000 0x1000>,      /* GIC Dist */
+		      <0x78020000 0x1000>,      /* GIC CPU1 */
+		      <0x78040000 0x2000>,      /* GIC VCPU Control */
+		      <0x78060000 0x1000>,      /* GIC VCPU1 */
+		      <0x78030000 0x1000>,      /* GIC CPU2 */
+		      <0x78070000 0x1000>;      /* GIC VCPU2 */
+		interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
 	};
arch/arm64/boot/dts/apm-storm.dtsi +4 -2
index bfdc578..b5d141a 100644
@@ -82,9 +82,11 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x0 0x78010000 0x0 0x1000>,	/* GIC Dist */
-		      <0x0 0x78020000 0x0 0x1000>,	/* GIC CPU */
+		      <0x0 0x78020000 0x0 0x1000>,	/* GIC CPU1 */
 		      <0x0 0x78040000 0x0 0x2000>,	/* GIC VCPU Control */
-		      <0x0 0x78060000 0x0 0x2000>;	/* GIC VCPU */
+		      <0x0 0x78060000 0x0 0x1000>,	/* GIC VCPU1 */
+		      <0x0 0x78030000 0x0 0x1000>,	/* GIC CPU2 */
+		      <0x0 0x78070000 0x0 0x1000>;	/* GIC VCPU2 */
 		interrupts = <1 9 0xf04>;	/* GIC Maintenence IRQ */
 	};
 
Signature · 1 line
1.8.4.rc3
#4 lore raw

PATCH 2/2 arm: Support for platforms with split GIC cpu interface registers.

Quoted 7 lines · Ian Campbell

At least one platform (APM Storm) places the two pages of the GIC cpu interface (and the vcpu side) at non-contiguous locations. Document two additional regions to cover this split and update the corresponding dtsi. Note that Linux (including KVM) does not use any registers in the second page so there is no associated code change here. Xen will use these new regions, although I've not written the corresponding code yet.

Quoted 5 lines

The ordering of these new regs is slightly counter intuitive but is inteded to be backward compatible. It is also assumed that all such systems will implement the GIC virtualisation extensions.

Add comments to all of the reg examples to help clarify what is going on.

Adding Catalin, Marc Z, and Will D.

I looked up the GIC-400 TRM (more specifically page 33 of DDI0471B_gic400_r0p1_trm.pdf) but could not find any info on additional page for CPU interface.

Am I looking at the wrong doc?

--
Anup

Quoted 125 lines
Cc devicetree at vger.kernel.org
Cc linux-arm-kernel at lists.infradead.org
Cc Kumar Sankaran <[email protected]>
Cc Loc Ho <[email protected]>
Cc Feng Kan <[email protected]>
---
 Documentation/devicetree/bindings/arm/gic.txt | 57 +++++++++++++++++++++------
 arch/arm64/boot/dts/apm-storm.dtsi            |  6 ++-
 2 files changed, 50 insertions(+), 13 deletions(-)
Documentation/devicetree/bindings/arm/gic.txt +46 -11
index ea215e8..00836d9 100644
@@ -38,7 +38,8 @@ Main node required properties:
 
 - reg : Specifies base physical address(s) and size of the GIC registers. The
   first region is the GIC distributor register base and size. The 2nd region is
-  the GIC cpu interface register base and size.
+  the GIC cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 Optional
 - interrupts   : Interrupt source of the parent interrupt controller on
@@ -56,8 +57,8 @@ Example:
                #interrupt-cells = <3>;
                #address-cells = <1>;
                interrupt-controller;
-               reg = <0xfff11000 0x1000>,
-                     <0xfff10100 0x100>;
+               reg = <0xfff11000 0x1000>,      /* GIC Dist */
+                     <0xfff10100 0x100>;       /* GIC CPU */
        };
 
 
@@ -70,9 +71,11 @@ primary interrupt controller).
 Required properties:
 
 - reg : Additional regions specifying the base physical address and
-  size of the VGIC registers. The first additional region is the GIC
-  virtual interface control register base and size. The 2nd additional
-  region is the GIC virtual cpu interface register base and size.
+  size of the VGIC registers. The first additional region (i.e. third
+  overall) is the GIC virtual interface control register base and
+  size. The 2nd additional region (i.e. forth overall) is the GIC
+  virtual cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 - interrupts : VGIC maintenance interrupt.
 
@@ -82,9 +85,41 @@ Example:
                compatible = "arm,cortex-a15-gic";
                #interrupt-cells = <3>;
                interrupt-controller;
-               reg = <0x2c001000 0x1000>,
-                     <0x2c002000 0x2000>,
-                     <0x2c004000 0x2000>,
-                     <0x2c006000 0x2000>;
-               interrupts = <1 9 0xf04>;
+               reg = <0x2c001000 0x1000>,      /* GIC Dist */
+                     <0x2c002000 0x2000>,      /* GIC CPU */
+                     <0x2c004000 0x2000>,      /* GIC VCPU Control */
+                     <0x2c006000 0x2000>;      /* GIC VCPU1 */
+               interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
+       };
+
+* Split GIC cpu interface
+
+  The cpu interfaces (bare-metal in region 2 and virtual in region 4)
+  may be spread over two pages, with the GICC_DIR (Deactivate
+  Interrupt Register) register falling at the start of the second
+  page. If these pages are contiguous then this is described via the
+  size of the second and fourth entries as described above
+  (e.g. 0x2000 rather than 0x1000).
+
+  However if the two pages are not contiguous then two additional
+  regions are present (5th and 6th) describing the location of the the
+  second half of the GIC cpu interface and GIC virtual cpu interface
+  respectively.
+
+  It is assumed that all such systems will implement the GIC
+  virtualisation extensions.
+
+Example:
+
+       gic: interrupt-controller at 78010000 {
+               compatible = "arm,cortex-a15-gic";
+               #interrupt-cells = <3>;
+               interrupt-controller;
+               reg = <0x78010000 0x1000>,      /* GIC Dist */
+                     <0x78020000 0x1000>,      /* GIC CPU1 */
+                     <0x78040000 0x2000>,      /* GIC VCPU Control */
+                     <0x78060000 0x1000>,      /* GIC VCPU1 */
+                     <0x78030000 0x1000>,      /* GIC CPU2 */
+                     <0x78070000 0x1000>;      /* GIC VCPU2 */
+               interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
        };
arch/arm64/boot/dts/apm-storm.dtsi +4 -3
index bfdc578..b5d141a 100644
@@ -82,9 +82,11 @@
                #interrupt-cells = <3>;
                interrupt-controller;
                reg = <0x0 0x78010000 0x0 0x1000>,      /* GIC Dist */
-                     <0x0 0x78020000 0x0 0x1000>,      /* GIC CPU */
+                     <0x0 0x78020000 0x0 0x1000>,      /* GIC CPU1 */
                      <0x0 0x78040000 0x0 0x2000>,      /* GIC VCPU Control */
-                     <0x0 0x78060000 0x0 0x2000>;      /* GIC VCPU */
+                     <0x0 0x78060000 0x0 0x1000>,      /* GIC VCPU1 */
+                     <0x0 0x78030000 0x0 0x1000>,      /* GIC CPU2 */
+                     <0x0 0x78070000 0x0 0x1000>;      /* GIC VCPU2 */
                interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
        };
 
--

1.8.4.rc3

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#5 lore raw

PATCH 2/2 arm: Support for platforms with split GIC cpu interface registers.

Quoted 14 lines · Anup Patel
Quoted 7 lines · Ian Campbell

At least one platform (APM Storm) places the two pages of the GIC cpu interface (and the vcpu side) at non-contiguous locations. Document two additional regions to cover this split and update the corresponding dtsi. Note that Linux (including KVM) does not use any registers in the second page so there is no associated code change here. Xen will use these new regions, although I've not written the corresponding code yet.

Quoted 5 lines

The ordering of these new regs is slightly counter intuitive but is inteded to be backward compatible. It is also assumed that all such systems will implement the GIC virtualisation extensions.

Add comments to all of the reg examples to help clarify what is going on.

Quoted 7 lines

Adding Catalin, Marc Z, and Will D.

I looked up the GIC-400 TRM (more specifically page 33 of DDI0471B_gic400_r0p1_trm.pdf) but could not find any info on additional page for CPU interface.

Am I looking at the wrong doc?

Never mind, found the GICC_DIR (offset 0x1000) register.

--
Anup

Quoted 129 lines

--
Anup

Quoted 125 lines
Cc devicetree at vger.kernel.org
Cc linux-arm-kernel at lists.infradead.org
Cc Kumar Sankaran <[email protected]>
Cc Loc Ho <[email protected]>
Cc Feng Kan <[email protected]>
---
 Documentation/devicetree/bindings/arm/gic.txt | 57 +++++++++++++++++++++------
 arch/arm64/boot/dts/apm-storm.dtsi            |  6 ++-
 2 files changed, 50 insertions(+), 13 deletions(-)
Documentation/devicetree/bindings/arm/gic.txt +46 -11
index ea215e8..00836d9 100644
@@ -38,7 +38,8 @@ Main node required properties:
 
 - reg : Specifies base physical address(s) and size of the GIC registers. The
   first region is the GIC distributor register base and size. The 2nd region is
-  the GIC cpu interface register base and size.
+  the GIC cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 Optional
 - interrupts   : Interrupt source of the parent interrupt controller on
@@ -56,8 +57,8 @@ Example:
                #interrupt-cells = <3>;
                #address-cells = <1>;
                interrupt-controller;
-               reg = <0xfff11000 0x1000>,
-                     <0xfff10100 0x100>;
+               reg = <0xfff11000 0x1000>,      /* GIC Dist */
+                     <0xfff10100 0x100>;       /* GIC CPU */
        };
 
 
@@ -70,9 +71,11 @@ primary interrupt controller).
 Required properties:
 
 - reg : Additional regions specifying the base physical address and
-  size of the VGIC registers. The first additional region is the GIC
-  virtual interface control register base and size. The 2nd additional
-  region is the GIC virtual cpu interface register base and size.
+  size of the VGIC registers. The first additional region (i.e. third
+  overall) is the GIC virtual interface control register base and
+  size. The 2nd additional region (i.e. forth overall) is the GIC
+  virtual cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 - interrupts : VGIC maintenance interrupt.
 
@@ -82,9 +85,41 @@ Example:
                compatible = "arm,cortex-a15-gic";
                #interrupt-cells = <3>;
                interrupt-controller;
-               reg = <0x2c001000 0x1000>,
-                     <0x2c002000 0x2000>,
-                     <0x2c004000 0x2000>,
-                     <0x2c006000 0x2000>;
-               interrupts = <1 9 0xf04>;
+               reg = <0x2c001000 0x1000>,      /* GIC Dist */
+                     <0x2c002000 0x2000>,      /* GIC CPU */
+                     <0x2c004000 0x2000>,      /* GIC VCPU Control */
+                     <0x2c006000 0x2000>;      /* GIC VCPU1 */
+               interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
+       };
+
+* Split GIC cpu interface
+
+  The cpu interfaces (bare-metal in region 2 and virtual in region 4)
+  may be spread over two pages, with the GICC_DIR (Deactivate
+  Interrupt Register) register falling at the start of the second
+  page. If these pages are contiguous then this is described via the
+  size of the second and fourth entries as described above
+  (e.g. 0x2000 rather than 0x1000).
+
+  However if the two pages are not contiguous then two additional
+  regions are present (5th and 6th) describing the location of the the
+  second half of the GIC cpu interface and GIC virtual cpu interface
+  respectively.
+
+  It is assumed that all such systems will implement the GIC
+  virtualisation extensions.
+
+Example:
+
+       gic: interrupt-controller at 78010000 {
+               compatible = "arm,cortex-a15-gic";
+               #interrupt-cells = <3>;
+               interrupt-controller;
+               reg = <0x78010000 0x1000>,      /* GIC Dist */
+                     <0x78020000 0x1000>,      /* GIC CPU1 */
+                     <0x78040000 0x2000>,      /* GIC VCPU Control */
+                     <0x78060000 0x1000>,      /* GIC VCPU1 */
+                     <0x78030000 0x1000>,      /* GIC CPU2 */
+                     <0x78070000 0x1000>;      /* GIC VCPU2 */
+               interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
        };
arch/arm64/boot/dts/apm-storm.dtsi +4 -3
index bfdc578..b5d141a 100644
@@ -82,9 +82,11 @@
                #interrupt-cells = <3>;
                interrupt-controller;
                reg = <0x0 0x78010000 0x0 0x1000>,      /* GIC Dist */
-                     <0x0 0x78020000 0x0 0x1000>,      /* GIC CPU */
+                     <0x0 0x78020000 0x0 0x1000>,      /* GIC CPU1 */
                      <0x0 0x78040000 0x0 0x2000>,      /* GIC VCPU Control */
-                     <0x0 0x78060000 0x0 0x2000>;      /* GIC VCPU */
+                     <0x0 0x78060000 0x0 0x1000>,      /* GIC VCPU1 */
+                     <0x0 0x78030000 0x0 0x1000>,      /* GIC CPU2 */
+                     <0x0 0x78070000 0x0 0x1000>;      /* GIC VCPU2 */
                interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
        };
 
--

1.8.4.rc3

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#6 lore raw

PATCH 2/2 arm: Support for platforms with split GIC cpu interface registers.

Quoted 149 lines · Anup Patel
Quoted 14 lines · Anup Patel
Quoted 7 lines · Ian Campbell

At least one platform (APM Storm) places the two pages of the GIC cpu interface (and the vcpu side) at non-contiguous locations. Document two additional regions to cover this split and update the corresponding dtsi. Note that Linux (including KVM) does not use any registers in the second page so there is no associated code change here. Xen will use these new regions, although I've not written the corresponding code yet.

Quoted 5 lines

The ordering of these new regs is slightly counter intuitive but is inteded to be backward compatible. It is also assumed that all such systems will implement the GIC virtualisation extensions.

Add comments to all of the reg examples to help clarify what is going on.

Quoted 7 lines

Adding Catalin, Marc Z, and Will D.

I looked up the GIC-400 TRM (more specifically page 33 of DDI0471B_gic400_r0p1_trm.pdf) but could not find any info on additional page for CPU interface.

Am I looking at the wrong doc?

Never mind, found the GICC_DIR (offset 0x1000) register.

--
Anup

Quoted 121 lines

--
Anup

Quoted 117 lines
Cc devicetree at vger.kernel.org
Cc linux-arm-kernel at lists.infradead.org
Cc Kumar Sankaran <[email protected]>
Cc Loc Ho <[email protected]>
Cc Feng Kan <[email protected]>
---
 Documentation/devicetree/bindings/arm/gic.txt | 57 +++++++++++++++++++++------
 arch/arm64/boot/dts/apm-storm.dtsi            |  6 ++-
 2 files changed, 50 insertions(+), 13 deletions(-)
Documentation/devicetree/bindings/arm/gic.txt +46 -11
index ea215e8..00836d9 100644
@@ -38,7 +38,8 @@ Main node required properties:
 
 - reg : Specifies base physical address(s) and size of the GIC registers. The
   first region is the GIC distributor register base and size. The 2nd region is
-  the GIC cpu interface register base and size.
+  the GIC cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 Optional
 - interrupts   : Interrupt source of the parent interrupt controller on
@@ -56,8 +57,8 @@ Example:
                #interrupt-cells = <3>;
                #address-cells = <1>;
                interrupt-controller;
-               reg = <0xfff11000 0x1000>,
-                     <0xfff10100 0x100>;
+               reg = <0xfff11000 0x1000>,      /* GIC Dist */
+                     <0xfff10100 0x100>;       /* GIC CPU */
        };
 
 
@@ -70,9 +71,11 @@ primary interrupt controller).
 Required properties:
 
 - reg : Additional regions specifying the base physical address and
-  size of the VGIC registers. The first additional region is the GIC
-  virtual interface control register base and size. The 2nd additional
-  region is the GIC virtual cpu interface register base and size.
+  size of the VGIC registers. The first additional region (i.e. third
+  overall) is the GIC virtual interface control register base and
+  size. The 2nd additional region (i.e. forth overall) is the GIC
+  virtual cpu interface register base and size (See also "Split GIC
+  cpu interface", below).
 
 - interrupts : VGIC maintenance interrupt.
 
@@ -82,9 +85,41 @@ Example:
                compatible = "arm,cortex-a15-gic";
                #interrupt-cells = <3>;
                interrupt-controller;
-               reg = <0x2c001000 0x1000>,
-                     <0x2c002000 0x2000>,
-                     <0x2c004000 0x2000>,
-                     <0x2c006000 0x2000>;
-               interrupts = <1 9 0xf04>;
+               reg = <0x2c001000 0x1000>,      /* GIC Dist */
+                     <0x2c002000 0x2000>,      /* GIC CPU */
+                     <0x2c004000 0x2000>,      /* GIC VCPU Control */
+                     <0x2c006000 0x2000>;      /* GIC VCPU1 */
+               interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
+       };
+
+* Split GIC cpu interface
+
+  The cpu interfaces (bare-metal in region 2 and virtual in region 4)
+  may be spread over two pages, with the GICC_DIR (Deactivate
+  Interrupt Register) register falling at the start of the second
+  page. If these pages are contiguous then this is described via the
+  size of the second and fourth entries as described above
+  (e.g. 0x2000 rather than 0x1000).
+
+  However if the two pages are not contiguous then two additional
+  regions are present (5th and 6th) describing the location of the the
+  second half of the GIC cpu interface and GIC virtual cpu interface
+  respectively.
+
+  It is assumed that all such systems will implement the GIC
+  virtualisation extensions.
+
+Example:
+
+       gic: interrupt-controller at 78010000 {
+               compatible = "arm,cortex-a15-gic";
+               #interrupt-cells = <3>;
+               interrupt-controller;
+               reg = <0x78010000 0x1000>,      /* GIC Dist */
+                     <0x78020000 0x1000>,      /* GIC CPU1 */
+                     <0x78040000 0x2000>,      /* GIC VCPU Control */
+                     <0x78060000 0x1000>,      /* GIC VCPU1 */
+                     <0x78030000 0x1000>,      /* GIC CPU2 */
+                     <0x78070000 0x1000>;      /* GIC VCPU2 */
+               interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
        };
arch/arm64/boot/dts/apm-storm.dtsi +4 -2
index bfdc578..b5d141a 100644
@@ -82,9 +82,11 @@
                #interrupt-cells = <3>;
                interrupt-controller;
                reg = <0x0 0x78010000 0x0 0x1000>,      /* GIC Dist */
-                     <0x0 0x78020000 0x0 0x1000>,      /* GIC CPU */
+                     <0x0 0x78020000 0x0 0x1000>,      /* GIC CPU1 */
                      <0x0 0x78040000 0x0 0x2000>,      /* GIC VCPU Control */
-                     <0x0 0x78060000 0x0 0x2000>;      /* GIC VCPU */
+                     <0x0 0x78060000 0x0 0x1000>,      /* GIC VCPU1 */
+                     <0x0 0x78030000 0x0 0x1000>,      /* GIC CPU2 */
+                     <0x0 0x78070000 0x0 0x1000>;      /* GIC VCPU2 */
                interrupts = <1 9 0xf04>;       /* GIC Maintenence IRQ */
        };
 
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines

--
1.8.4.rc3

I have looked at the proposed device tree binding change from APM X-Gene perspective.

This change looks good to me. (Vinayak ??)

Regards,
Anup

Quoted 10 lines
Quoted 5 lines
Quoted 5 lines

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel