Add power management support for chipidea
v3 cover Add power management support for chipidea
Hi Greg,
This serial adds power management (system & runtime) for chipidea core. With this, the chipidea controller can be at low power mode when it is not in use, and the chipidea controller can be the system wakeup source.
It needs to depend on my patch[1], since [1]-"Add power management support for MXS PHY" adds some common PHY APIs, and this serial uses it.
It has been verified at Freescale i.mx6Q/DL SabreSD, i.mx28 evk platform (no runtime pm support), I will verify it at other FSL platforms during the patch review.
Hi Alan,
Due to chipidea core and imx concontroller needs some special operations during the standard ehci routine, I override .hub_control, .bus_suspend, and .bus_resume.
There is one special thing is I use flag ehci->bus_suspended to know it was a global suspend before due to I need to notify PHY when the suspend has finished (portsc.suspendM is set) and the resume signal has finished (portsc.fpr is cleared) for high speed device, but there are two places will send suspend/resume, and I don't want to patch ehci-hub.c (if you think patch ehci-hub.c is a good way, I can do it).
The related host patches:
usb: chipidea: host: add quirk for ehci operation
usb: chipidea: host: add ehci quirk for imx controller
My github tree: https://github.com/hzpeterchen/linux-usb
branch: master
It is based on linux-next-1029.
Changes for v3:
- Using flag bit to indicate SoC features/bugs [7/10][10/10]
Changes for v2:
- Do not use atomic_read and atomic_set for ci->in_lpm
- Do not use "supports_runtime_pm" as DT property due to it is not a hardware feature, instead of it, we use compatible string to enable it.
Peter Chen (10):
usb: chipidea: Add power management support
usb: chipidea: imx: add power management support
usb: chipidea: add wakeup interrupt handler
usb: chipidea: usbmisc_imx: remove the controller's clock information
usb: chipidea: usbmisc_imx: add set_wakup API
usb: chipidea: imx: call set_wakeup when necessary
usb: chipidea: imx: Enable runtime pm support for imx6q
usb: chipidea: host: add quirk for ehci operation
usb: chipidea: host: add ehci quirk for imx controller
usb: chipidea: imx: Enable CI_HDRC_IMX_EHCI_QUIRK
drivers/usb/chipidea/ci.h | 3 + drivers/usb/chipidea/ci_hdrc_imx.c | 156 ++++++++++++++++++++++++++++++- drivers/usb/chipidea/ci_hdrc_imx.h | 1 + drivers/usb/chipidea/core.c | 139 +++++++++++++++++++++++++++ drivers/usb/chipidea/host.c | 180 ++++++++++++++++++++++++++++++++++++ drivers/usb/chipidea/otg.c | 5 + drivers/usb/chipidea/usbmisc_imx.c | 59 ++++++++---- include/linux/usb/chipidea.h | 2 + 8 files changed, 522 insertions(+), 23 deletions(-)
PATCH v3 1/10 usb: chipidea: Add power management support
This commit adds runtime and system power management support for chipidea core. The runtime pm support is controlled by glue layer, it can be enabled by flag CI_HDRC_SUPPORTS_RUNTIME_PM.
--- drivers/usb/chipidea/ci.h | 2 + drivers/usb/chipidea/core.c | 119 ++++++++++++++++++++++++++++++++++++++++++ include/linux/usb/chipidea.h | 1 + 3 files changed, 122 insertions(+), 0 deletions(-)
drivers/usb/chipidea/ci.h +2 -0
@@ -175,6 +175,8 @@ struct ci_hdrc {bool b_sess_valid_event;/* imx28 needs swp instruction for writing */ bool imx28_write_fix; +bool supports_runtime_pm; +bool in_lpm; };static inline struct ci_role_driver *ci_role (struct ci_hdrc *ci)
drivers/usb/chipidea/core.c +119 -0
148 lines not on this page · raw message
include/linux/usb/chipidea.h +1 -0
@@ -18,6 +18,7 @@ struct ci_hdrc_platform_data {unsigned long flags;#define CI_HDRC_REGS_SHARED BIT(0)#define CI_HDRC_REQUIRE_TRANSCEIVER BIT(1) +#define CI_HDRC_SUPPORTS_RUNTIME_PM BIT(2)#define CI_HDRC_DISABLE_STREAMING BIT(3)/* * Only set it when DCCPARAMS.DC==1 and DCCPARAMS.HC==1,
Signature · 1 line
1.7.1
PATCH v3 2/10 usb: chipidea: imx: add power management support
In reply to Peter ChenAdd system and runtime power management support for imx gluy layer.
--- drivers/usb/chipidea/ci_hdrc_imx.c | 94 ++++++++++++++++++++++++++++++++++- 1 files changed, 91 insertions(+), 3 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +91 -3
@@ -48,6 +48,8 @@ struct ci_hdrc_imx_data {struct platform_device *ci_pdev;struct clk *clk;struct imx_usbmisc_data *usbmisc_data; +bool supports_runtime_pm; +bool in_lpm; };/* Common functions shared by usbmisc drivers */
@@ -176,8 +178,12 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)platform_set_drvdata (pdev, data); -pm_runtime_no_callbacks (&pdev->dev); -pm_runtime_enable (&pdev->dev); +device_set_wakeup_capable (&pdev->dev, true); + +if (data->supports_runtime_pm) { +pm_runtime_set_active (&pdev->dev); +pm_runtime_enable (&pdev->dev); + }return 0 ;
@@ -192,13 +198,94 @@ static int ci_hdrc_imx_remove(struct platform_device *pdev) {struct ci_hdrc_imx_data *data =platform_get_drvdata (pdev); -pm_runtime_disable (&pdev->dev);ci_hdrc_remove_device (data->ci_pdev); +if (data->supports_runtime_pm) { +pm_runtime_get_sync (&pdev->dev); +pm_runtime_disable (&pdev->dev); +pm_runtime_put_noidle (&pdev->dev); + } +clk_disable_unprepare (data->clk); + +return 0 ; +} + +#ifdef CONFIG_PM +static int imx_controller_suspend (struct device *dev) +{ +struct ci_hdrc_imx_data *data =dev_get_drvdata (dev); + +dev_dbg (dev,"at %s\n" , __func__); + +if (data->in_lpm) +return 0 ; +clk_disable_unprepare (data->clk); + data->in_lpm = true; +return 0 ; } +static int imx_controller_resume (struct device *dev) +{ +struct ci_hdrc_imx_data *data =dev_get_drvdata (dev); +int ret =0 ; + +dev_dbg (dev,"at %s\n" , __func__); + +if (!data->in_lpm) +return 0 ; + + ret =clk_prepare_enable (data->clk); +if (ret) +return ret; + + data->in_lpm = false; + +return ret; +} + +#ifdef CONFIG_PM_SLEEP +static int ci_hdrc_imx_suspend (struct device *dev) +{ +return imx_controller_suspend (dev); +} + +static int ci_hdrc_imx_resume (struct device *dev) +{ +struct ci_hdrc_imx_data *data =dev_get_drvdata (dev); +int ret; + + ret =imx_controller_resume (dev); +if (!ret && data->supports_runtime_pm) { +pm_runtime_disable (dev); +pm_runtime_set_active (dev); +pm_runtime_enable (dev); + } + +return ret; +} +#endif /* CONFIG_PM_SLEEP */ + +#ifdef CONFIG_PM_RUNTIME +static int ci_hdrc_imx_runtime_suspend (struct device *dev) +{ +return imx_controller_suspend (dev); +} + +static int ci_hdrc_imx_runtime_resume (struct device *dev) +{ +return imx_controller_resume (dev); +} +#endif /* CONFIG_PM_RUNTIME */ + +#endif /* CONFIG_PM */ +static const struct dev_pm_ops ci_hdrc_imx_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(ci_hdrc_imx_suspend, ci_hdrc_imx_resume) +SET_RUNTIME_PM_OPS (ci_hdrc_imx_runtime_suspend, + ci_hdrc_imx_runtime_resume,NULL ) +}; +static struct platform_driver ci_hdrc_imx_driver = { .probe = ci_hdrc_imx_probe, .remove = ci_hdrc_imx_remove,
@@ -206,6 +293,7 @@ static struct platform_driver ci_hdrc_imx_driver = { .name = "imx_usb", .owner = THIS_MODULE, .of_match_table = ci_hdrc_imx_dt_ids, + .pm = &ci_hdrc_imx_pm_ops, }, };
Signature · 1 line
1.7.1
PATCH v3 3/10 usb: chipidea: add wakeup interrupt handler
In reply to Peter ChenWhen the controller is at suspend mode, it can be waken up by external events (like vbus, dp/dm or id change). Once we receive the wakeup interrupt, we need to resume the controller first, eg open clocks, disable some wakeup settings, etc. After that, the controller can receive the normal USB interrupts.
--- drivers/usb/chipidea/ci.h | 1 + drivers/usb/chipidea/core.c | 20 ++++++++++++++++++++ drivers/usb/chipidea/otg.c | 5 +++++ 3 files changed, 26 insertions(+), 0 deletions(-)
drivers/usb/chipidea/ci.h +1 -0
@@ -177,6 +177,7 @@ struct ci_hdrc {bool imx28_write_fix;bool supports_runtime_pm;bool in_lpm; +bool wakeup_int; };static inline struct ci_role_driver *ci_role (struct ci_hdrc *ci)
drivers/usb/chipidea/core.c +20 -0
@@ -190,6 +190,13 @@ static void ci_hdrc_enter_lpm(struct ci_hdrc *ci, bool enable)* than 1ms) to leave low power mode. */ usleep_range (1500 ,2000 ); + }else if (!enable) { +/* +* At wakeup interrupt, the phcd will be cleared by hardware +* automatically, but the controller needs at least 1ms +* to reflect PHY's status. +*/ +usleep_range (1200 ,1800 ); } }
@@ -355,6 +362,13 @@ static irqreturn_t ci_irq(int irq, void *data)irqreturn_t ret =IRQ_NONE ;u32 otgsc =0 ; +if (ci->in_lpm) { +disable_irq_nosync (irq); + ci->wakeup_int = true; +pm_runtime_get (ci->dev); +return IRQ_HANDLED ; + } +if (ci->is_otg) otgsc =hw_read (ci,OP_OTGSC , ~0 );
@@ -744,6 +758,12 @@ static int ci_controller_resume(struct device *dev) ci->in_lpm = false; +if (ci->wakeup_int) { + ci->wakeup_int = false; +enable_irq (ci->irq); +pm_runtime_put (ci->dev); + } +return 0 ; }
drivers/usb/chipidea/otg.c +5 -0
@@ -78,10 +78,15 @@ static void ci_otg_work(struct work_struct *work)if (ci->id_event) { ci->id_event = false; +/* Keep controller active during id switch */ +pm_runtime_get_sync (ci->dev);ci_handle_id_switch (ci); +pm_runtime_put_sync (ci->dev); }else if (ci->b_sess_valid_event) { ci->b_sess_valid_event = false; +pm_runtime_get_sync (ci->dev);ci_handle_vbus_change (ci); +pm_runtime_put_sync (ci->dev); }else dev_err (ci->dev,"unexpected event occurs at %s\n" , __func__);
Signature · 1 line
1.7.1
PATCH v3 4/10 usb: chipidea: usbmisc_imx: remove the controller's clock information
In reply to Peter ChenCurrently, the usbmisc is just an API supplier for controller driver, the controller calls related APIs to handle different things among the SoCs, before calling it, the clock must be on. So the clock operation is useless for usbmisc, it also increases the difficulties to manage the clock, especially at runtime power management situation.
--- drivers/usb/chipidea/usbmisc_imx.c | 18 ------------------ 1 files changed, 0 insertions(+), 18 deletions(-)
drivers/usb/chipidea/usbmisc_imx.c +0 -18
@@ -11,7 +11,6 @@#include <linux/module.h> #include <linux/of_platform.h> -#include <linux/clk.h> #include <linux/err.h> #include <linux/io.h> #include <linux/delay.h>
@@ -40,7 +39,6 @@ struct usbmisc_ops {struct imx_usbmisc {void __iomem *base;spinlock_t lock; -struct clk *clk;const struct usbmisc_ops *ops; };
@@ -177,7 +175,6 @@ static int usbmisc_imx_probe(struct platform_device *pdev) {struct resource *res;struct imx_usbmisc *data; -int ret;struct of_device_id *tmp_dev;if (usbmisc)
@@ -194,20 +191,6 @@ static int usbmisc_imx_probe(struct platform_device *pdev)if (IS_ERR (data->base))return PTR_ERR (data->base); - data->clk =devm_clk_get (&pdev->dev,NULL ); -if (IS_ERR (data->clk)) { -dev_err (&pdev->dev, -"failed to get clock, err=%ld\n" ,PTR_ERR (data->clk)); -return PTR_ERR (data->clk); - } - - ret =clk_prepare_enable (data->clk); -if (ret) { -dev_err (&pdev->dev, -"clk_prepare_enable failed, err=%d\n" , ret); -return ret; - } - tmp_dev = (struct of_device_id *)of_match_device (usbmisc_imx_dt_ids, &pdev->dev); data->ops = (const struct usbmisc_ops *)tmp_dev->data;
@@ -218,7 +201,6 @@ static int usbmisc_imx_probe(struct platform_device *pdev)static int usbmisc_imx_remove (struct platform_device *pdev) { -clk_disable_unprepare (usbmisc->clk); usbmisc =NULL ;return 0 ; }
Signature · 1 line
1.7.1
PATCH v3 5/10 usb: chipidea: usbmisc_imx: add set_wakup API
In reply to Peter ChenIt is used to enable USB wakeup, currently only imx6 SoC serial usb's wakeup is enabled.
--- drivers/usb/chipidea/ci_hdrc_imx.h | 1 + drivers/usb/chipidea/usbmisc_imx.c | 41 ++++++++++++++++++++++++++++++++++++ 2 files changed, 42 insertions(+), 0 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.h +1 -0
@@ -18,3 +18,4 @@ struct imx_usbmisc_data {int imx_usbmisc_init (struct imx_usbmisc_data *);int imx_usbmisc_init_post (struct imx_usbmisc_data *); +int imx_usbmisc_set_wakeup (struct imx_usbmisc_data *,bool );
drivers/usb/chipidea/usbmisc_imx.c +41 -0
71 lines not on this page · raw message
Signature · 1 line
1.7.1
PATCH v3 6/10 usb: chipidea: imx: call set_wakeup when necessary
In reply to Peter Chen- Disable wakeup after probe
- Enable wakeup during the suspend
- Disable wakeup after controller is active
--- drivers/usb/chipidea/ci_hdrc_imx.c | 36 ++++++++++++++++++++++++++++++++++++ 1 files changed, 36 insertions(+), 0 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +36 -0
@@ -176,6 +176,15 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev) } } +if (data->usbmisc_data) { + ret =imx_usbmisc_set_wakeup (data->usbmisc_data, false); +if (ret) { +dev_err (&pdev->dev,"usbmisc set_wakeup failed, ret=%d\n" , + ret); + goto disable_device; + } + } +platform_set_drvdata (pdev, data);device_set_wakeup_capable (&pdev->dev, true);
@@ -213,12 +222,23 @@ static int ci_hdrc_imx_remove(struct platform_device *pdev)static int imx_controller_suspend (struct device *dev) {struct ci_hdrc_imx_data *data =dev_get_drvdata (dev); +int ret;dev_dbg (dev,"at %s\n" , __func__);if (data->in_lpm)return 0 ; +if (data->usbmisc_data) { + ret =imx_usbmisc_set_wakeup (data->usbmisc_data, true); +if (ret) { +dev_err (dev, +"usbmisc set_wakeup failed, ret=%d\n" , + ret); +return ret; + } + } +clk_disable_unprepare (data->clk); data->in_lpm = true;
@@ -242,6 +262,22 @@ static int imx_controller_resume(struct device *dev) data->in_lpm = false; +if (data->usbmisc_data) { + ret =imx_usbmisc_set_wakeup (data->usbmisc_data, false); +if (ret) { +dev_err (dev, +"usbmisc set_wakeup failed, ret=%d\n" , + ret); + ret = -EINVAL ; + goto clk_disable; + } + } + +return 0 ; + +clk_disable: +clk_disable_unprepare (data->clk); +return ret; }
Signature · 1 line
1.7.1
PATCH v3 7/10 usb: chipidea: imx: Enable runtime pm support for imx6q
In reply to Peter ChenCurrently, only imx6q adds wakeup logic, so only enable runtime pm for imx6q.
--- drivers/usb/chipidea/ci_hdrc_imx.c | 13 ++++++++++++- 1 files changed, 12 insertions(+), 1 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +12 -1
@@ -23,7 +23,8 @@#include "ci.h" #include "ci_hdrc_imx.h" -#define CI_HDRC_IMX_IMX28_WRITE_FIX BIT(0) +#define CI_HDRC_IMX_IMX28_WRITE_FIX BIT(0) +#define CI_HDRC_IMX_SUPPORT_RUNTIME_PM BIT(1)struct ci_hdrc_imx_platform_flag {unsigned int flags;
@@ -36,7 +37,12 @@ static const struct ci_hdrc_imx_platform_flag imx28_usb_data = { .flags = CI_HDRC_IMX_IMX28_WRITE_FIX, }; +static const struct ci_hdrc_imx_platform_flag imx6q_usb_data = { + .flags =CI_HDRC_IMX_SUPPORT_RUNTIME_PM , +}; +static const struct of_device_id ci_hdrc_imx_dt_ids[] = { + { .compatible ="fsl,imx6q-usb" , .data = &imx6q_usb_data}, { .compatible ="fsl,imx28-usb" , .data = &imx28_usb_data}, { .compatible ="fsl,imx27-usb" , .data = &imx27_usb_data}, {/* sentinel */ }
@@ -147,6 +153,11 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)if (imx_platform_flag->flags &CI_HDRC_IMX_IMX28_WRITE_FIX ) pdata.flags |=CI_HDRC_IMX28_WRITE_FIX ; +if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) + pdata.flags |=CI_HDRC_SUPPORTS_RUNTIME_PM ; + data->supports_runtime_pm = true; + } +if (data->usbmisc_data) { ret =imx_usbmisc_init (data->usbmisc_data);if (ret) {
Signature · 1 line
1.7.1
PATCH v3 8/10 usb: chipidea: host: add quirk for ehci operation
In reply to Peter ChenFor chipidea controller, it does not follow ehci spec strictly. Taking resume signal as an example, it will stop resume signal about 20-21ms later automatically, but standard ehci spec says, the resume signal is controlled by software (clear portsc.PORT_RESUME).
This operation causes some remote wakeup problems for high speed devices due to host controller does not send SOF in time since software can't guarantee set run/stop bit in time (run/stop bit was cleared at the ehci suspend routine).
When software sets run/stop bit, it needs 1 SoF time to make it effect. If we close the PHY clock just after setting run/stop bit, it does not be set in practice, so a software delay is needed.
--- drivers/usb/chipidea/host.c | 51 +++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 51 insertions(+), 0 deletions(-)
drivers/usb/chipidea/host.c +51 -0
@@ -33,6 +33,53 @@#include "host.h" static struct hc_driver __read_mostly ci_ehci_hc_driver; +static int (*orig_bus_suspend)(struct usb_hcd *hcd); + +static int ci_ehci_bus_suspend (struct usb_hcd *hcd) +{ +struct ehci_hcd *ehci =hcd_to_ehci (hcd); +int port; +u32 tmp; + +int ret =orig_bus_suspend (hcd); + +if (ret) +return ret; + + port =HCS_N_PORTS (ehci->hcs_params); +while (port--) { +u32 __iomem *reg = &ehci->regs->port_status[port]; +u32 portsc =ehci_readl (ehci, reg); + +if (portsc &PORT_CONNECT ) { +/* +* For chipidea, the resume signal will be ended +* automatically, so for remote wakeup case, the +* usbcmd.rs may not be set before the resume has +* ended if other resume path consumes too much +* time (~23ms-24ms), in that case, the SOF will not +* send out within 3ms after resume ends, then the +* device will enter suspend again. +*/ +if (hcd->self.root_hub->do_remote_wakeup) { +ehci_dbg (ehci, +"Remote wakeup is enabled, " +"and device is on the port\n" ); + + tmp =ehci_readl (ehci, &ehci->regs->command); + tmp |=CMD_RUN ; +ehci_writel (ehci, tmp, &ehci->regs->command); +/* +* It needs a short delay between set RUNSTOP +* and set PHCD. +*/ +udelay (125 ); + } + } + } + +return 0 ; +}static irqreturn_t host_irq (struct ci_hdrc *ci) {
@@ -135,5 +182,9 @@ int ci_hdrc_host_init(struct ci_hdrc *ci)ehci_init_driver (&ci_ehci_hc_driver,NULL ); + orig_bus_suspend = ci_ehci_hc_driver.bus_suspend; + + ci_ehci_hc_driver.bus_suspend = ci_ehci_bus_suspend; +return 0 ; }
Signature · 1 line
1.7.1
PATCH v3 9/10 usb: chipidea: host: add ehci quirk for imx controller
In reply to Peter ChenWhen the port goes to suspend or finishes resme, it needs to notify PHY, it is not a standard EHCI operation, so we add a quirk for it.
--- drivers/usb/chipidea/host.c | 129 ++++++++++++++++++++++++++++++++++++++++++ include/linux/usb/chipidea.h | 1 + 2 files changed, 130 insertions(+), 0 deletions(-)
drivers/usb/chipidea/host.c +129 -0
@@ -34,6 +34,10 @@static struct hc_driver __read_mostly ci_ehci_hc_driver;static int (*orig_bus_suspend)(struct usb_hcd *hcd); +static int (*orig_bus_resume)(struct usb_hcd *hcd); +static int (*orig_hub_control)(struct usb_hcd *hcd, +u16 typeReq,u16 wValue,u16 wIndex, +char *buf,u16 wLength);static int ci_ehci_bus_suspend (struct usb_hcd *hcd) {
@@ -75,12 +79,131 @@ static int ci_ehci_bus_suspend(struct usb_hcd *hcd)*/ udelay (125 ); } +if (hcd->phy &&test_bit (port, &ehci->bus_suspended) + && (ehci_port_speed (ehci, portsc) == +USB_PORT_STAT_HIGH_SPEED )) +/* +* notify the USB PHY, it is for global +* suspend case. +*/ +usb_phy_notify_suspend (hcd->phy, +USB_SPEED_HIGH ); } }return 0 ; } +static int ci_imx_ehci_bus_resume (struct usb_hcd *hcd) +{ +struct ehci_hcd *ehci =hcd_to_ehci (hcd); +int port; + +int ret =orig_bus_resume (hcd); + +if (ret) +return ret; + + port =HCS_N_PORTS (ehci->hcs_params); +while (port--) { +u32 __iomem *reg = &ehci->regs->port_status[port]; +u32 portsc =ehci_readl (ehci, reg); +/* +* Notify PHY after resume signal has finished, it is +* for global suspend case. +*/ +if (hcd->phy + &&test_bit (port, &ehci->bus_suspended) + && (portsc &PORT_CONNECT ) + && (ehci_port_speed (ehci, portsc) == +USB_PORT_STAT_HIGH_SPEED )) +/* notify the USB PHY */ +usb_phy_notify_resume (hcd->phy,USB_SPEED_HIGH ); + } + +return 0 ; +} + +/* The below code is based on tegra ehci driver */ +static int ci_imx_ehci_hub_control ( +struct usb_hcd *hcd, +u16 typeReq, +u16 wValue, +u16 wIndex, +char *buf, +u16 wLength +) +{ +struct ehci_hcd *ehci =hcd_to_ehci (hcd); +u32 __iomem *status_reg; +u32 temp; +unsigned long flags; +int retval =0 ; + + status_reg = &ehci->regs->port_status[(wIndex &0xff ) -1 ]; + +spin_lock_irqsave (&ehci->lock, flags); + +if (typeReq == SetPortFeature && wValue ==USB_PORT_FEAT_SUSPEND ) { + temp =ehci_readl (ehci, status_reg); +if ((temp &PORT_PE ) ==0 || (temp &PORT_RESET ) !=0 ) { + retval = -EPIPE ; + goto done; + } + + temp &= ~(PORT_RWC_BITS |PORT_WKCONN_E ); + temp |=PORT_WKDISC_E |PORT_WKOC_E ; +ehci_writel (ehci, temp |PORT_SUSPEND , status_reg); + +/* +* If a transaction is in progress, there may be a delay in +* suspending the port. Poll until the port is suspended. +*/ +if (ehci_handshake (ehci, status_reg,PORT_SUSPEND , +PORT_SUSPEND ,5000 )) +ehci_err (ehci,"timeout waiting for SUSPEND\n" ); + +spin_unlock_irqrestore (&ehci->lock, flags); +if (ehci_port_speed (ehci, temp) == +USB_PORT_STAT_HIGH_SPEED && hcd->phy) { +/* notify the USB PHY */ +usb_phy_notify_suspend (hcd->phy,USB_SPEED_HIGH ); + } +spin_lock_irqsave (&ehci->lock, flags); + +set_bit ((wIndex &0xff ) -1 , &ehci->suspended_ports); + goto done; + } + +/* +* After resume has finished, it needs do some post resume +* operation for some SoCs. +*/ +else if (typeReq == ClearPortFeature && + wValue ==USB_PORT_FEAT_C_SUSPEND ) { + +/* Make sure the resume has finished, it should be finished */ +if (ehci_handshake (ehci, status_reg,PORT_RESUME ,0 ,25000 )) +ehci_err (ehci,"timeout waiting for resume\n" ); + + temp =ehci_readl (ehci, status_reg); + +if (ehci_port_speed (ehci, temp) == +USB_PORT_STAT_HIGH_SPEED && hcd->phy) { +/* notify the USB PHY */ +usb_phy_notify_resume (hcd->phy,USB_SPEED_HIGH ); + } + } + +spin_unlock_irqrestore (&ehci->lock, flags); + +/* Handle the hub control events here */ +return orig_hub_control (hcd, typeReq, wValue, wIndex, buf, wLength); +done: +spin_unlock_irqrestore (&ehci->lock, flags); +return retval; +} +static irqreturn_t host_irq (struct ci_hdrc *ci) {return usb_hcd_irq (ci->irq, ci->hcd);
@@ -183,8 +306,14 @@ int ci_hdrc_host_init(struct ci_hdrc *ci)ehci_init_driver (&ci_ehci_hc_driver,NULL ); orig_bus_suspend = ci_ehci_hc_driver.bus_suspend; + orig_bus_resume = ci_ehci_hc_driver.bus_resume; + orig_hub_control = ci_ehci_hc_driver.hub_control; ci_ehci_hc_driver.bus_suspend = ci_ehci_bus_suspend; +if (ci->platdata->flags &CI_HDRC_IMX_EHCI_QUIRK ) { + ci_ehci_hc_driver.bus_resume = ci_imx_ehci_bus_resume; + ci_ehci_hc_driver.hub_control = ci_imx_ehci_hub_control; + }return 0 ; }
include/linux/usb/chipidea.h +1 -0
@@ -26,6 +26,7 @@ struct ci_hdrc_platform_data {*/ #define CI_HDRC_DUAL_ROLE_NOT_OTG BIT(4)#define CI_HDRC_IMX28_WRITE_FIX BIT(5) +#define CI_HDRC_IMX_EHCI_QUIRK BIT(6)enum usb_dr_mode dr_mode;#define CI_HDRC_CONTROLLER_RESET_EVENT 0#define CI_HDRC_CONTROLLER_STOPPED_EVENT 1
Signature · 1 line
1.7.1
PATCH v3 10/10 usb: chipidea: imx: Enable CI_HDRC_IMX_EHCI_QUIRK
In reply to Peter ChenEnable CI_HDRC_IMX_EHCI_QUIRK for controllers who use mxs-phy.
--- drivers/usb/chipidea/ci_hdrc_imx.c | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)
drivers/usb/chipidea/ci_hdrc_imx.c +14 -3
@@ -25,6 +25,7 @@#define CI_HDRC_IMX_IMX28_WRITE_FIX BIT(0)#define CI_HDRC_IMX_SUPPORT_RUNTIME_PM BIT(1) +#define CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK BIT(2)struct ci_hdrc_imx_platform_flag {unsigned int flags;
@@ -33,17 +34,24 @@ struct ci_hdrc_imx_platform_flag {static const struct ci_hdrc_imx_platform_flag imx27_usb_data = { }; +static const struct ci_hdrc_imx_platform_flag imx23_usb_data = { + .flags =CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , +}; +static const struct ci_hdrc_imx_platform_flag imx28_usb_data = { - .flags =CI_HDRC_IMX_IMX28_WRITE_FIX , + .flags =CI_HDRC_IMX_IMX28_WRITE_FIX | +CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , };static const struct ci_hdrc_imx_platform_flag imx6q_usb_data = { - .flags =CI_HDRC_IMX_SUPPORT_RUNTIME_PM , + .flags =CI_HDRC_IMX_SUPPORT_RUNTIME_PM | +CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , };static const struct of_device_id ci_hdrc_imx_dt_ids[] = { { .compatible ="fsl,imx6q-usb" , .data = &imx6q_usb_data}, { .compatible ="fsl,imx28-usb" , .data = &imx28_usb_data}, + { .compatible ="fsl,imx23-usb" , .data = &imx23_usb_data}, { .compatible ="fsl,imx27-usb" , .data = &imx27_usb_data}, {/* sentinel */ } };
@@ -153,11 +161,14 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)if (imx_platform_flag->flags &CI_HDRC_IMX_IMX28_WRITE_FIX ) pdata.flags |=CI_HDRC_IMX28_WRITE_FIX ; -if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) +if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) { pdata.flags |=CI_HDRC_SUPPORTS_RUNTIME_PM ; data->supports_runtime_pm = true; } +if (imx_platform_flag->flags &CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK ) + pdata.flags |=CI_HDRC_IMX_EHCI_QUIRK ; +if (data->usbmisc_data) { ret =imx_usbmisc_init (data->usbmisc_data);if (ret) {
Signature · 1 line
1.7.1
PATCH v3 10/10 usb: chipidea: imx: Enable CI_HDRC_IMX_EHCI_QUIRK
Quoted 47 lines · Peter Chen
Enable
CI_HDRC_IMX_EHCI_QUIRKfor controllers who use mxs-phy.Signed-off-by Peter Chen <[email protected]>--- drivers/usb/chipidea/ci_hdrc_imx.c | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)drivers/usb/chipidea/ci_hdrc_imx.c +10
-2@@ -25,6 +25,7 @@#define CI_HDRC_IMX_IMX28_WRITE_FIX BIT(0)#define CI_HDRC_IMX_SUPPORT_RUNTIME_PM BIT(1) +#define CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK BIT(2)struct ci_hdrc_imx_platform_flag {unsigned int flags;@@ -33,17 +34,24 @@ struct ci_hdrc_imx_platform_flag {static const struct ci_hdrc_imx_platform_flag imx27_usb_data = { }; +static const struct ci_hdrc_imx_platform_flag imx23_usb_data = { + .flags =CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , +}; +static const struct ci_hdrc_imx_platform_flag imx28_usb_data = { - .flags =CI_HDRC_IMX_IMX28_WRITE_FIX , + .flags =CI_HDRC_IMX_IMX28_WRITE_FIX | +CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , };static const struct ci_hdrc_imx_platform_flag imx6q_usb_data = { - .flags =CI_HDRC_IMX_SUPPORT_RUNTIME_PM , + .flags =CI_HDRC_IMX_SUPPORT_RUNTIME_PM | +CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , };static const struct of_device_id ci_hdrc_imx_dt_ids[] = { { .compatible ="fsl,imx6q-usb" , .data = &imx6q_usb_data}, { .compatible ="fsl,imx28-usb" , .data = &imx28_usb_data}, + { .compatible ="fsl,imx23-usb" , .data = &imx23_usb_data}, { .compatible ="fsl,imx27-usb" , .data = &imx27_usb_data}, {/* sentinel */ } };
drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 164
Quoted 5 lines
drivers/usb/chipidea/ci_hdrc_imx.c +1
-1@@ -153,11 +161,14 @@ static int ci_hdrc_imx_probe(struct platform_device *pdev)if (imx_platform_flag->flags &CI_HDRC_IMX_IMX28_WRITE_FIX ) pdata.flags |=CI_HDRC_IMX28_WRITE_FIX ; -if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) +if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) {
^^^^
Please squash into the correct patch.
drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 167
Quoted 3 lines
drivers/usb/chipidea/ci_hdrc_imx.c +0
-0pdata.flags |=CI_HDRC_SUPPORTS_RUNTIME_PM ; data->supports_runtime_pm = true; }
Marc
Signature · 12 lines
Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de | -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 259 bytes Desc: OpenPGP digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131203/bbeaee29/attachment.sig>
PATCH v3 10/10 usb: chipidea: imx: Enable CI_HDRC_IMX_EHCI_QUIRK
Quoted 53 lines · Peter Chen
Review
Quoted 8 lines
Enable
CI_HDRC_IMX_EHCI_QUIRKfor controllers who use mxs-phy.Signed-off-by Peter Chen <[email protected]>--- drivers/usb/chipidea/ci_hdrc_imx.c | 17 ++++++++++++++--- 1 files changed, 14 insertions(+), 3 deletions(-)(quoted diff) +0
-0
b/drivers/usb/chipidea/ci_hdrc_imx.cdrivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct
Quoted 39 lines
index fd26c38..78ccde1 100644
drivers/usb/chipidea/ci_hdrc_imx.c +10
-2@@ -25,6 +25,7 @@#define CI_HDRC_IMX_IMX28_WRITE_FIX BIT(0)#define CI_HDRC_IMX_SUPPORT_RUNTIME_PM BIT(1) +#define CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK BIT(2)struct ci_hdrc_imx_platform_flag {unsigned int flags;@@ -33,17 +34,24 @@ struct ci_hdrc_imx_platform_flag {static const struct ci_hdrc_imx_platform_flag imx27_usb_data = { }; +static const struct ci_hdrc_imx_platform_flag imx23_usb_data = { + .flags =CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , +}; +static const struct ci_hdrc_imx_platform_flag imx28_usb_data = { - .flags =CI_HDRC_IMX_IMX28_WRITE_FIX , + .flags =CI_HDRC_IMX_IMX28_WRITE_FIX | +CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , };static const struct ci_hdrc_imx_platform_flag imx6q_usb_data = { - .flags =CI_HDRC_IMX_SUPPORT_RUNTIME_PM , + .flags =CI_HDRC_IMX_SUPPORT_RUNTIME_PM | +CI_HDRC_IMX_MXS_PHY_EHCI_QUIRK , };static const struct of_device_id ci_hdrc_imx_dt_ids[] = { { .compatible ="fsl,imx6q-usb" , .data = &imx6q_usb_data}, { .compatible ="fsl,imx28-usb" , .data = &imx28_usb_data}, + { .compatible ="fsl,imx23-usb" , .data = &imx23_usb_data}, { .compatible ="fsl,imx27-usb" , .data = &imx27_usb_data}, {/* sentinel */ } };@@ -153,11 +161,14 @@ static int ci_hdrc_imx_probe(struct
platform_device*pdev)
Quoted 9 lines
drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 164
Quoted 5 lines
drivers/usb/chipidea/ci_hdrc_imx.c +1
-1if (imx_platform_flag->flags &CI_HDRC_IMX_IMX28_WRITE_FIX ) pdata.flags |=CI_HDRC_IMX28_WRITE_FIX ; -if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) +if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) {^^^^Please squash into the correct patch.
There are some re-work for this serial, I will do it.
But I don't get your mean why it needs to squash into another patch?
Peter
PATCH v3 10/10 usb: chipidea: imx: Enable CI_HDRC_IMX_EHCI_QUIRK
Quoted 2 lines · Peter Chen
There are some re-work for this serial, I will do it.
But I don't get your mean why it needs to squash into another patch?
Let's look at the code again:
drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 167
Quoted 5 lines
drivers/usb/chipidea/ci_hdrc_imx.c +1
-1-if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) +if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) { pdata.flags |=CI_HDRC_SUPPORTS_RUNTIME_PM ; data->supports_runtime_pm = true; }
Without that patch, the driver will not compile.
before:
if ()
/* code */ }
after:
if () {
/* code */
}Marc
Signature · 12 lines
Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de | -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 259 bytes Desc: OpenPGP digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20131204/38456ffe/attachment.sig>
PATCH v3 10/10 usb: chipidea: imx: Enable CI_HDRC_IMX_EHCI_QUIRK
Quoted 20 lines · Marc Kleine-Budde
Quoted 2 lines · Peter Chen
There are some re-work for this serial, I will do it.
But I don't get your mean why it needs to squash into another patch?Let's look at the code again:
drivers/usb/chipidea/ci_hdrc_imx.c static int ci_hdrc_imx_probe(struct platform_device *pdev) · line 167
Quoted 5 lines
drivers/usb/chipidea/ci_hdrc_imx.c +1
-1-if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) +if (imx_platform_flag->flags &CI_HDRC_IMX_SUPPORT_RUNTIME_PM ) { pdata.flags |=CI_HDRC_SUPPORTS_RUNTIME_PM ; data->supports_runtime_pm = true; }Without that patch, the driver will not compile.
before:
if ()
/* code */ }
Quoted 9 lines
after:
if () { /* code */ }Marc
Oh, thanks. I need to sqhash [7/10] and [10/10]
Signature · 2 lines
Best Regards, Peter Chen
Greg KH
maintainerv3 cover Add power management support for chipidea
In reply to Peter ChenQuoted 11 lines · Peter Chen
Hi Greg,
This serial adds power management (system & runtime) for chipidea core. With this, the chipidea controller can be at low power mode when it is not in use, and the chipidea controller can be the system wakeup source.
It needs to depend on my patch[1], since [1]-"Add power management support for MXS PHY" adds some common PHY APIs, and this serial uses it.It has been verified at Freescale i.mx6Q/DL SabreSD, i.mx28 evk platform (no runtime pm support), I will verify it at other FSL platforms during the patch review.
This series doesn't apply to my tree anymore.
And there have been a ton of chipidea patches floating around, I've now dropped them all from my "todo" queue and will wait for you to collect them and forward them on as I'm totally lost with all of the different versions and objections and the like.
thanks,
greg k-h
v3 cover Add power management support for chipidea
Quoted 16 lines
Quoted 5 lines
Hi Greg,
This serial adds power management (system & runtime) for chipidea core. With this, the chipidea controller can be at low power mode when it is
not in
Quoted 2 lines
use, and the chipidea controller can be the system wakeup source. It needs to depend on my patch[1], since [1]-"Add power management
support for MXS PHY"
Quoted 3 lines
adds some common PHY APIs, and this serial uses it.
It has been verified at Freescale i.mx6Q/DL SabreSD, i.mx28 evk
platform
Quoted 2 lines
(no runtime pm support), I will verify it at other FSL platforms during the patch review.
Quoted 7 lines
This series doesn't apply to my tree anymore.
And there have been a ton of chipidea patches floating around, I've now dropped them all from my "todo" queue and will wait for you to collect them and forward them on as I'm totally lost with all of the different versions and objections and the like.
Greg, I will do that.
Peter