Skip to contentSkip to conversation

Bug report - Wrong naming of my Wireless Network card enp3s6, should have been wlp3s6

PATCH In review Frans Leerink 3 participants 4 messages Nov 8, 2013 – Nov 11, 2013 Networking drivers (wireless)

lore
Share & tools
lore
#0 lore raw

Hello,

I have installed openSUSE 12.3 / KDE on my Medion Notebook MD41300 with an INTEL Pentium 4 CPU 3.0 GHz and 1 Gb memory and everything works oke, including wireless.

I am testing openSUSE 13.1 RC2 with this older laptop. Up to now it has worked very well through all the releases upto openSUSE/KDE 12.3.

On the moment I test the live openSUSE/KDE 13.1 RC2 via an usb-stick. The system comes up nicely but the wireless network card does not work and generates the following lines in dmesg output:

[ 48.675564] enp3s6: resetting device...
[ 48.675587] enp3s6: uploading firmware...
[ 48.855166] prism54: request_firmware() failed for 'isl3890'
[ 48.855175] enp3s6: could not upload firmware ('isl3890')
[ 48.855179] enp3s6: islpci_reset: failure

While I followed URL:
http://wireless.kernel.org/en/users/Drivers/p54
to activate driver p54pci, the same as I had done for all the previous releases.

The wireless networkcard, according to command "/sbin/lspci"
Networkcontroller: "Intersil Corporation ISL3890 [Prism GT/Prism Duette] /ISL3886 [Prism Javelin/Prism Xbow] (rev 01)".

The kernel version is according to command uname -r :

     3.11.6-3-default

I checked on the openSUSE forum wih Larry Finger, in thread:

http://forums.opensuse.org/english/get-technical-help-here/install-boot-login/413006-please-help-enabling-p54-wireless-firmware-kernel-according-url-http-wireless-kernel-org-en-users-drivers-p54-2.html

and he noticed that my wireless get the wrong naming "enp3s6" in stead of "wlp..."
He proposed a way to still test my wireless card by adding an entry, 70-persistent-net.rules (with the mac address of my wireless card and wlan0 in it) to /etc/udev/rules.d/

I have added that line to /etc/udev/rules.d/70-persistent-net.rules and deactivated prism54 driver and activated p54pci driver (via modprobe) and the wireless device started working correctly.

Quoted 6 lines

Below the relevant entries from dmesg
In the beginning

[ 3.245827] Loaded prism54 driver, version 1.2

then somewhere
[ ] systemd-udevd [230]:renamed network interface

eth1 to enp3s6

Quoted 31 lines

At the end

[561.396409] enp3s6: removing device
[ 561.471117] Unloaded prism54 driver
[ 737.932041] cfg80211: Calling CRDA to update world regulatory domain
[ 738.248459] ieee80211 phy0: p54 detected a LM86 firmware
[ 738.248470] p54: rx_mtu reduced from 3240 to 2376
[ 738.248476] ieee80211 phy0: FW rev 2.13.25.0 - Softmac protocol 5.9
[ 738.248483] ieee80211 phy0: cryptographic accelerator WEP:YES,
TKIP:YES, CCMP:YES
[ 738.359804] cfg80211: World regulatory domain updated:
[ 738.359812] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 738.359816] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 738.359820] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 738.359823] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300
mBi, 2000 mBm)
[ 738.359826] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 738.359829] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 739.102119] ieee80211 phy0: hwaddr 00:60:b3:1e:5a:fd, MAC:isl3890
RF:Frisbee
[ 739.314682] ieee80211 phy0: Selected rate control algorithm
'minstrel_ht'
[ 739.316966] p54pci 0000:03:06.0: is registered as 'phy0'
[ 739.532327] systemd-udevd[2433]: renamed network interface wlan0 to
wlp3s6
[ 739.860509] IPv6: ADDRCONF(NETDEV_UP): wlp3s6: link is not ready
[ 740.057475] NET: Registered protocol family 17
Quoted 8 lines
[ 754.446569] wlp3s6: authenticate with bc:05:43:f2:77:b4
[ 754.446780] wlp3s6: send auth to bc:05:43:f2:77:b4 (try 1/3)
[ 754.451362] wlp3s6: authenticated
[ 754.452090] wlp3s6: associate with bc:05:43:f2:77:b4 (try 1/3)
[ 754.454695] wlp3s6: RX AssocResp from bc:05:43:f2:77:b4 (capab=0x431
status=0 aid=2)
[ 754.455114] wlp3s6: associated
[ 754.455175] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s6: link becomes 

ready

Quoted 13 lines
[ 754.455301] cfg80211: Calling CRDA for country: DE
[ 754.473156] cfg80211: Regulatory domain changed to country: DE
[ 754.473169] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 754.473173] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 754.473177] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 754.473181] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz),
(N/A, 2000 mBm)
[ 754.473185] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz),
(N/A, 2698 mBm)
[ 754.473188] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz),
Quoted 2 lines

(N/A, 4000 mBm)
linux:/home/linux #

The problem is now why assigned the openSUSE 13.1 RC2 live USB-stick
initialy the wrong naming enp3s6 to my Wireless Network card.

Regards / Groeten,

Frans

#1 lore raw

PATCH 1/1 prism54: set netdev type to "wlan"

Userspace uses the netdev devtype for stuff like device naming and type detection. Be nice and set it. Remove the pointless #if/#endif around SET_NETDEV_DEV too.

---

drivers/net/wireless/prism54/islpci_dev.c +5 -2
index 5970ff6..d498b02 100644
@@ -807,27 +807,30 @@ static const struct net_device_ops islpci_netdev_ops = {
 	.ndo_start_xmit		= islpci_eth_transmit,
 	.ndo_tx_timeout		= islpci_eth_tx_timeout,
 	.ndo_set_mac_address 	= prism54_set_mac_address,
 	.ndo_change_mtu		= eth_change_mtu,
 	.ndo_validate_addr	= eth_validate_addr,
 };
 
+static struct device_type wlan_type = {
+	.name	= "wlan",
+};
+
 struct net_device *
 islpci_setup(struct pci_dev *pdev)
 {
 	islpci_private *priv;
 	struct net_device *ndev = alloc_etherdev(sizeof (islpci_private));
 
 	if (!ndev)
 		return ndev;
 
 	pci_set_drvdata(pdev, ndev);
-#if defined(SET_NETDEV_DEV)
 	SET_NETDEV_DEV(ndev, &pdev->dev);
-#endif
+	SET_NETDEV_DEVTYPE(ndev, &wlan_type);
 
 	/* setup the structure members */
 	ndev->base_addr = pci_resource_start(pdev, 0);
 	ndev->irq = pdev->irq;
 
 	/* initialize the function pointers */
 	ndev->netdev_ops = &islpci_netdev_ops;
#2 lore raw

Re: [PATCH] prism54: set netdev type to "wlan"

Quoted 5 lines · Dan Williams

Userspace uses the netdev devtype for stuff like device naming and type detection. Be nice and set it. Remove the pointless #if/#endif around SET_NETDEV_DEV too.

Should this be sent to Stable?

Larry

Quoted 44 lines

---

drivers/net/wireless/prism54/islpci_dev.c +5 -3
index 5970ff6..d498b02 100644
@@ -807,27 +807,30 @@ static const struct net_device_ops islpci_netdev_ops = {
  	.ndo_start_xmit		= islpci_eth_transmit,
  	.ndo_tx_timeout		= islpci_eth_tx_timeout,
  	.ndo_set_mac_address 	= prism54_set_mac_address,
  	.ndo_change_mtu		= eth_change_mtu,
  	.ndo_validate_addr	= eth_validate_addr,
  };
 
+static struct device_type wlan_type = {
+	.name	= "wlan",
+};
+
  struct net_device *
  islpci_setup(struct pci_dev *pdev)
  {
  	islpci_private *priv;
  	struct net_device *ndev = alloc_etherdev(sizeof (islpci_private));
 
  	if (!ndev)
  		return ndev;
 
  	pci_set_drvdata(pdev, ndev);
-#if defined(SET_NETDEV_DEV)
  	SET_NETDEV_DEV(ndev, &pdev->dev);
-#endif
+	SET_NETDEV_DEVTYPE(ndev, &wlan_type);
 
  	/* setup the structure members */
  	ndev->base_addr = pci_resource_start(pdev, 0);
  	ndev->irq = pdev->irq;
 
  	/* initialize the function pointers */
  	ndev->netdev_ops = &islpci_netdev_ops;
 
--

To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#3 lore raw

Re: [PATCH] prism54: set netdev type to "wlan"

Quoted 8 lines · Larry Finger
Quoted 5 lines · Dan Williams

Userspace uses the netdev devtype for stuff like device naming and type detection. Be nice and set it. Remove the pointless #if/#endif around SET_NETDEV_DEV too.

Should this be sent to Stable?

Probably, yeah.

Dan

Quoted 51 lines

Larry

Quoted 40 lines

---

drivers/net/wireless/prism54/islpci_dev.c +5 -3
index 5970ff6..d498b02 100644
@@ -807,27 +807,30 @@ static const struct net_device_ops islpci_netdev_ops = {
  	.ndo_start_xmit		= islpci_eth_transmit,
  	.ndo_tx_timeout		= islpci_eth_tx_timeout,
  	.ndo_set_mac_address 	= prism54_set_mac_address,
  	.ndo_change_mtu		= eth_change_mtu,
  	.ndo_validate_addr	= eth_validate_addr,
  };
 
+static struct device_type wlan_type = {
+	.name	= "wlan",
+};
+
  struct net_device *
  islpci_setup(struct pci_dev *pdev)
  {
  	islpci_private *priv;
  	struct net_device *ndev = alloc_etherdev(sizeof (islpci_private));
 
  	if (!ndev)
  		return ndev;
 
  	pci_set_drvdata(pdev, ndev);
-#if defined(SET_NETDEV_DEV)
  	SET_NETDEV_DEV(ndev, &pdev->dev);
-#endif
+	SET_NETDEV_DEVTYPE(ndev, &wlan_type);
 
  	/* setup the structure members */
  	ndev->base_addr = pci_resource_start(pdev, 0);
  	ndev->irq = pdev->irq;
 
  	/* initialize the function pointers */
  	ndev->netdev_ops = &islpci_netdev_ops;
 
--
Quoted 4 lines

To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html