arm, at91: support for the taurus, axm and corvus board
v3 cover arm, at91: support for the taurus, axm and corvus board
add support for the AT91SAM9G20 boards from siemens. The patches are checkpatch clean, and a "./MAKEALL -s at91" compiles clean. Resending this patchset now without switching to the 'ATMEL_LEGACY' PIO API (Are there some patches I missed?)
I hope I find time for sending the patches for booting this boards with SPL code soon ...
The 2 needed patches from previous patchseries:
arm926ejs, at91: add common phy_reset function
http://git.denx.de/?p=u-boot/u-boot-atmel.git;a=commit;h=4535a24c0c06e367bc40c43b4807bdb335513a1a
at91: add defines for reset type
http://git.denx.de/?p=u-boot/u-boot-atmel.git;a=commit;h=c12f941bece9ed79efccfe9e4a9fd977da6975f9
found there way to mainline :-)
Heiko Schocher (2):
arm, at91: add Siemens board taurus and axm
arm, at91: add siemens corvus board
board/siemens/corvus/Makefile | 18 ++++ board/siemens/corvus/board.c | 195 ++++++++++++++++++++++++++++++++++++++++++ board/siemens/taurus/Makefile | 18 ++++ board/siemens/taurus/taurus.c | 160 ++++++++++++++++++++++++++++++++++ boards.cfg | 3 + include/configs/corvus.h | 165 +++++++++++++++++++++++++++++++++++ include/configs/taurus.h | 160 ++++++++++++++++++++++++++++++++++ 7 files changed, 719 insertions(+) create mode 100644 board/siemens/corvus/Makefile create mode 100644 board/siemens/corvus/board.c create mode 100644 board/siemens/taurus/Makefile create mode 100644 board/siemens/taurus/taurus.c create mode 100644 include/configs/corvus.h create mode 100644 include/configs/taurus.h
Signature · 1 line
1.8.3.1
PATCH v3 1/2 arm, at91: add Siemens board taurus and axm
enable support for the siemens AT91SAM9G20 based boards taurus and axm.
---
- changes for v2:
- add comments from bo shen
- use gpio api
- remove unneccessary comment
- use at91_wait_for_reset()
- remove unneccessary code in board file
- Coding Style cleanup (tabs and unneccessary 1 after config define removed)
- add commit message
- add comments from Andreas Bie?mann <[email protected]>:
- detect sdram size on startup without read dram setting
- get rid of MACH_TYPE definition in config file
- changes for v3:
- add comments from Andreas Bie?mann:
- remove empty line
- move at91_seriald_hw_init to early_init
- include <net.h> unconditionally
- rebased against current commit
2cee0408e5c6f5dbdfa89fb40168ba2ead3f61a6
- rebased based on the spl patches from Bo Shen, see:
http://lists.denx.de/pipermail/u-boot/2013-November/166272.html
- add CONFIG_AT91_WANTS_COMMON_PHY
---
board/siemens/taurus/Makefile | 18 +++++
board/siemens/taurus/taurus.c | 160 ++++++++++++++++++++++++++++++++++++++++++
boards.cfg | 2 +
include/configs/taurus.h | 160 ++++++++++++++++++++++++++++++++++++++++++
4 files changed, 340 insertions(+)
create mode 100644 board/siemens/taurus/Makefile
create mode 100644 board/siemens/taurus/taurus.c
create mode 100644 include/configs/taurus.hboard/siemens/taurus/Makefile new file +18 -0
@@ -0,0 +1,18 @@ +# +# Makefile for Siemens TAURUS (AT91SAM9G20) based board +# (C) Copyright 2013 Siemens AG +# +# Based on: +# U-Boot file: board/atmel/at91sam9260ek/Makefile +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# (C) Copyright 2008 +# Stelian Pop <[email protected]> +# Lead Tech Design <www.leadtechdesign.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += taurus.o
board/siemens/taurus/taurus.c new file +160 -0
160 lines not on this page · raw message
boards.cfg +2 -0
@@ -139,6 +139,8 @@ Active arm arm926ejs at91 ronetix pm9263 Active arm arm926ejs at91 ronetix pm9g45 pm9g45 pm9g45:AT91SAM9G45 Ilko Iliev <[email protected]> Active arm arm926ejs at91 taskit stamp9g20 portuxg20 stamp9g20:AT91SAM9G20,PORTUXG20 Markus Hubig <[email protected]> Active arm arm926ejs at91 taskit stamp9g20 stamp9g20 stamp9g20:AT91SAM9G20 Markus Hubig <[email protected]> +Active arm arm926ejs at91 siemens taurus axm taurus:AT91SAM9G20,MACH_TYPE=2068,BOARD_AXM Heiko Schocher <[email protected]> +Active arm arm926ejs at91 siemens taurus taurus taurus:AT91SAM9G20,MACH_TYPE=2067,BOARD_TAURUS Heiko Schocher <[email protected]> Active arm arm926ejs davinci ait cam_enc_4xx cam_enc_4xx cam_enc_4xx Heiko Schocher <[email protected]> Active arm arm926ejs davinci Barix ipam390 ipam390 - Heiko Schocher <[email protected]> Active arm arm926ejs davinci davinci da8xxevm da830evm - Nick Thompson <[email protected]>
include/configs/taurus.h new file +160 -0
160 lines not on this page · raw message
Signature · 1 line
1.8.3.1
PATCH v3 1/2 arm, at91: add Siemens board taurus and axm
Dear Heiko Schocher,
Quoted 37 lines · Heiko Schocher
enable support for the siemens AT91SAM9G20 based boards taurus and axm.
Signed-off-by Roger Meier <[email protected]>Reviewed-by Heiko Schocher <[email protected]>Cc Andreas Bie?mann <[email protected]>Cc Bo Shen <[email protected]>---
- changes for v2:
- add comments from bo shen
- use gpio api
- remove unneccessary comment
- useat91_wait_for_reset()
- remove unneccessary code in board file
- Coding Style cleanup (tabs and unneccessary 1 after config define removed)
- add commit message
- add comments from Andreas Bie?mann <[email protected]>:
- detect sdram size on startup without read dram setting
- get rid ofMACH_TYPEdefinition in config file
- changes for v3:
- add comments from Andreas Bie?mann:
- remove empty line
- moveat91_seriald_hw_inittoearly_init
- include <net.h> unconditionally
- rebased against current commit2cee0408e5c6f5dbdfa89fb40168ba2ead3f61a6
- rebased based on the spl patches from Bo Shen, see:http://lists.denx.de/pipermail/u-boot/2013-November/166272.html - add CONFIG_AT91_WANTS_COMMON_PHY --- board/siemens/taurus/Makefile | 18 +++++ board/siemens/taurus/taurus.c | 160 ++++++++++++++++++++++++++++++++++++++++++ boards.cfg | 2 + include/configs/taurus.h | 160 ++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 340 insertions(+)
Quoted 3 lines
create mode 100644 board/siemens/taurus/Makefile create mode 100644
board/siemens/taurus/taurus.ccreate mode 100644include/configs/taurus.h
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v3 2/2 arm, at91: add siemens corvus board
In reply to Heiko Schocherenable support for the siemens AT91SAM9G20 based board corvus.
---
- changes for v2:
- add comments from Bo Shen
- use gpio api
- remove unneccessary comment
- use at91_wait_for_reset()
- remove unneccessary code in board file
- Coding Style cleanup (tabs and unneccessary 1 after config define removed, use ".xxx = x" notation for initializing structs)
- remove reset_phy()
- remove CONFIG_SYS_MEMTEST_x defines, as mtest command is not used on this board.
- changes load address
- delete lcd support
- add comments from Andreas Bie?mann:
- rearrange some init calls
- remove some unneeded ifdef
- changes for v3:
- add comments from Andreas Bie?mann:
- removed at91sam9m10g45ek_usb_hw_init() call
- removed empty reset_phy
- removed unneccessary tab
- use at91_phy_reset()
- rebased against current commit
2cee0408e5c6f5dbdfa89fb40168ba2ead3f61a6 - add CONFIG_AT91_WANTS_COMMON_PHY --- board/siemens/corvus/Makefile | 18 ++++ board/siemens/corvus/board.c | 195 ++++++++++++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/corvus.h | 165 +++++++++++++++++++++++++++++++++++ 4 files changed, 379 insertions(+) create mode 100644 board/siemens/corvus/Makefile create mode 100644 board/siemens/corvus/board.c create mode 100644 include/configs/corvus.h
board/siemens/corvus/Makefile new file +18 -0
@@ -0,0 +1,18 @@ +# +# Makefile for siemens CORVUS (AT91SAM9G45) based board +# (C) Copyright 2013 Siemens AG +# +# Based on: +# U-Boot file: board/atmel/at91sam9m10g45ek/Makefile +# +# (C) Copyright 2003-2008 +# Wolfgang Denk, DENX Software Engineering, wd at denx.de. +# +# (C) Copyright 2008 +# Stelian Pop <[email protected]> +# Lead Tech Design <www.leadtechdesign.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += board.o
board/siemens/corvus/board.c new file +195 -0
195 lines not on this page · raw message
boards.cfg +1 -0
@@ -140,6 +140,7 @@ Active arm arm926ejs at91 ronetix pm9g45 Active arm arm926ejs at91 taskit stamp9g20 portuxg20 stamp9g20:AT91SAM9G20,PORTUXG20 Markus Hubig <[email protected]> Active arm arm926ejs at91 taskit stamp9g20 stamp9g20 stamp9g20:AT91SAM9G20 Markus Hubig <[email protected]> Active arm arm926ejs at91 siemens taurus axm taurus:AT91SAM9G20,MACH_TYPE=2068,BOARD_AXM Heiko Schocher <[email protected]> +Active arm arm926ejs at91 siemens corvus corvus corvus:AT91SAM9M10G45,SYS_USE_NANDFLASH Heiko Schocher <[email protected]> Active arm arm926ejs at91 siemens taurus taurus taurus:AT91SAM9G20,MACH_TYPE=2067,BOARD_TAURUS Heiko Schocher <[email protected]> Active arm arm926ejs davinci ait cam_enc_4xx cam_enc_4xx cam_enc_4xx Heiko Schocher <[email protected]> Active arm arm926ejs davinci Barix ipam390 ipam390 - Heiko Schocher <[email protected]>
include/configs/corvus.h new file +165 -0
165 lines not on this page · raw message
Signature · 1 line
1.8.3.1
PATCH v3 2/2 arm, at91: add siemens corvus board
Dear Heiko Schocher,
Quoted 34 lines · Heiko Schocher
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by Boris Schmidt <[email protected]>Reviewed-by Heiko Schocher <[email protected]>Cc Andreas Bie?mann <[email protected]>Cc Bo Shen <[email protected]>---
- changes for v2:
- add comments from Bo Shen
- use gpio api
- remove unneccessary comment
- useat91_wait_for_reset()
- remove unneccessary code in board file
- Coding Style cleanup (tabs and unneccessary 1 after config define removed, use ".xxx = x" notation for initializing structs)
- removereset_phy()
- removeCONFIG_SYS_MEMTEST_xdefines, as mtest command is not used on this board.
- changes load address
- delete lcd support
- add comments from Andreas Bie?mann:
- rearrange some init calls
- remove some unneeded ifdef
- changes for v3:
- add comments from Andreas Bie?mann:
- removedat91sam9m10g45ek_usb_hw_init()call
- removed emptyreset_phy
- removed unneccessary tab
- useat91_phy_reset()
- rebased against current commit2cee0408e5c6f5dbdfa89fb40168ba2ead3f61a6
- addCONFIG_AT91_WANTS_COMMON_PHY
---
Quoted 8 lines
board/siemens/corvus/Makefile | 18 ++++ board/siemens/corvus/board.c | 195 ++++++++++++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/corvus.h | 165 +++++++++++++++++++++++++++++++++++ 4 files changed, 379 insertions(+)create mode 100644 board/siemens/corvus/Makefile
create mode 100644board/siemens/corvus/board.c
create mode 100644include/configs/corvus.h
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann