pinctrl: tegra: Add devicetree binding document for Tegra124
Subsystems (3)
PATCH v3 1/2 pinctrl: tegra: Add devicetree binding document for Tegra124
This device tree binding document describes the Tegra124 pincontrol DT bindings. This document lists all valid properties, names, mux options of Tegra124 pins.
---
Changes from V1:
- Referred the dt-binding header file on describing the nodes.
Changes from V2:
- Rewording reg properties.
- drop drv_type as it is not applicable.
.../bindings/pinctrl/nvidia,tegra124-pinmux.txt | 144 ++++++++++++++++++++ 1 files changed, 144 insertions(+), 0 deletions(-) create mode 100644 Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt
Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-pinmux.txt new file +144 -0
@@ -0,0 +1,144 @@ +NVIDIA Tegra124 pinmux controller + +The Tegra124 pinctrl binding is very similar to the Tegra20 and Tegra30 +pinctrl binding, as described in nvidia,tegra20-pinmux.txt and +nvidia,tegra30-pinmux.txt. In fact, this document assumes that binding as +a baseline, and only documents the differences between the two bindings. + +Required properties: +- compatible: "nvidia,tegra124-pinmux" +- reg: Should contain a list of base address and size pairs for: + -- first entry - the drive strength and pad control registers. + -- second entry - the pinmux registers + +Tegra124 adds the following optional properties for pin configuration subnodes. +The macros for options are defined in the + include/dt-binding/pinctrl/pinctrl-tegra.h. +- nvidia,enable-input: Integer. Enable the pin's input path. + enable :TEGRA_PIN_ENABLE0 and + disable or output only: TEGRA_PIN_DISABLE. +- nvidia,open-drain: Integer. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,lock: Integer. Lock the pin configuration against further changes + until reset. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,io-reset: Integer. Reset the IO path. + enable: TEGRA_PIN_ENABLE. + disable: TEGRA_PIN_DISABLE. +- nvidia,rcv-sel: Integer. Select VIL/VIH receivers. + normal: TEGRA_PIN_DISABLE + high: TEGRA_PIN_ENABLE + +Please refer the Tegra TRM for complete details regarding which groups +support which functionality. + +Valid values for pin and group names are: + + per-pin mux groups: + + These all support nvidia,function, nvidia,tristate, nvidia,pull, + nvidia,enable-input. Some support nvidia,lock nvidia,open-drain, + nvidia,io-reset and nvidia,rcv-sel. + + ulpi_data0_po1, ulpi_data1_po2, ulpi_data2_po3, ulpi_data3_po4, + ulpi_data4_po5, ulpi_data5_po6, ulpi_data6_po7, ulpi_data7_po0, + ulpi_clk_py0, ulpi_dir_py1, ulpi_nxt_py2, ulpi_stp_py3, dap3_fs_pp0, + dap3_din_pp1, dap3_dout_pp2, dap3_sclk_pp3, pv0, pv1, sdmmc1_clk_pz0, + sdmmc1_cmd_pz1, sdmmc1_dat3_py4, sdmmc1_dat2_py5, sdmmc1_dat1_py6, + sdmmc1_dat0_py7, clk2_out_pw5, clk2_req_pcc5, hdmi_int_pn7, ddc_scl_pv4, + ddc_sda_pv5, uart2_rxd_pc3, uart2_txd_pc2, uart2_rts_n_pj6, + uart2_cts_n_pj5, uart3_txd_pw6, uart3_rxd_pw7, uart3_cts_n_pa1, + uart3_rts_n_pc0, pu0, pu1, pu2, pu3, pu4, pu5, pu6, gen1_i2c_scl_pc4, + gen1_i2c_sda_pc5, dap4_fs_pp4, dap4_din_pp5, dap4_dout_pp6, + dap4_sclk_pp7, clk3_out_pee0, clk3_req_pee1, pc7, pi5, pi7, pk0, pk1, + pj0, pj2, pk3, pk4, pk2, pi3, pi6, pg0, pg1, pg2, pg3, pg4, pg5, pg6, + pg7, ph0, ph1, ph2, ph3, ph4, ph5, ph6, ph7, pj7, pb0, pb1, pk7, pi0, + pi1, pi2, pi4, gen2_i2c_scl_pt5, gen2_i2c_sda_pt6, sdmmc4_clk_pcc4, + sdmmc4_cmd_pt7, sdmmc4_dat0_paa0, sdmmc4_dat1_paa1, sdmmc4_dat2_paa2, + sdmmc4_dat3_paa3, sdmmc4_dat4_paa4, sdmmc4_dat5_paa5, sdmmc4_dat6_paa6, + sdmmc4_dat7_paa7, cam_mclk_pcc0, pcc1, pbb0, cam_i2c_scl_pbb1, + cam_i2c_sda_pbb2, pbb3, pbb4, pbb5, pbb6, pbb7, pcc2, jtag_rtck, + pwr_i2c_scl_pz6, pwr_i2c_sda_pz7, kb_row0_pr0, kb_row1_pr1, kb_row2_pr2, + kb_row3_pr3, kb_row4_pr4, kb_row5_pr5, kb_row6_pr6, kb_row7_pr7, + kb_row8_ps0, kb_row9_ps1, kb_row10_ps2, kb_row11_ps3, kb_row12_ps4, + kb_row13_ps5, kb_row14_ps6, kb_row15_ps7, kb_col0_pq0, kb_col1_pq1, + kb_col2_pq2, kb_col3_pq3, kb_col4_pq4, kb_col5_pq5, kb_col6_pq6, + kb_col7_pq7, clk_32k_out_pa0, core_pwr_req, cpu_pwr_req, pwr_int_n, + clk_32k_in, owr, dap1_fs_pn0, dap1_din_pn1, dap1_dout_pn2, + dap1_sclk_pn3, dap_mclk1_req_pee2, dap_mclk1_pw4, spdif_in_pk6, + spdif_out_pk5, dap2_fs_pa2, dap2_din_pa4, dap2_dout_pa5, dap2_sclk_pa3, + dvfs_pwm_px0, gpio_x1_aud_px1, gpio_x3_aud_px3, dvfs_clk_px2, + gpio_x4_aud_px4, gpio_x5_aud_px5, gpio_x6_aud_px6, gpio_x7_aud_px7, + sdmmc3_clk_pa6, sdmmc3_cmd_pa7, sdmmc3_dat0_pb7, sdmmc3_dat1_pb6, + sdmmc3_dat2_pb5, sdmmc3_dat3_pb4, pex_l0_rst_n_pdd1, + pex_l0_clkreq_n_pdd2, pex_wake_n_pdd3, pex_l1_rst_n_pdd5, + pex_l1_clkreq_n_pdd6, hdmi_cec_pee3, sdmmc1_wp_n_pv3, + sdmmc3_cd_n_pv2, gpio_w2_aud_pw2, gpio_w3_aud_pw3, usb_vbus_en0_pn4, + usb_vbus_en1_pn5, sdmmc3_clk_lb_out_pee4, sdmmc3_clk_lb_in_pee5, + gmi_clk_lb, reset_out_n, kb_row16_pt0, kb_row17_pt1, usb_vbus_en2_pff1, + pff2, dp_hpd_pff0, + + drive groups: + + These all support nvidia,pull-down-strength, nvidia,pull-up-strength, + nvidia,slew-rate-rising, nvidia,slew-rate-falling. Most but not all + support nvidia,high-speed-mode, nvidia,schmitt, nvidia,low-power-mode + and nvidia,drive-type. + + ao1, ao2, at1, at2, at3, at4, at5, cdev1, cdev2, dap1, dap2, dap3, dap4, + dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg, + gmh, owr, uda, gpv, dev3, cec, usb_vbus_en, ao3, ao0, hv0, sdio4, ao4. + +Valid values for nvidia,functions are: + + blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya, + displaya_alt, displayb, dtv, extperiph1, extperiph2, extperiph3, + gmi, gmi_alt, hda, hsi, i2c1, i2c2, i2c3, i2c4, i2cpwr, i2s0, + i2s1, i2s2, i2s3, i2s4, irda, kbc, owr, pmi, pwm0, pwm1, pwm2, pwm3, + pwron, reset_out_n, rsvd1, rsvd2, rsvd3, rsvd4, sdmmc1, sdmmc2, sdmmc3, + sdmmc4, soc, spdif, spi1, spi2, spi3, spi4, spi5, spi6, trace, uarta, + uartb, uartc, uartd, ulpi, usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6, + vi, vi_alt1, vi_alt3, vimclk2, vimclk2_alt, sata, ccla, pe0, pe, pe1, + dp, rtck, sys, clk tmds. + +Example: + + pinmux: pinmux { + compatible = "nvidia,tegra124-pinmux"; + reg = <0x70000868 0x164 /* Pad control registers */ + 0x70003000 0x434>; /* PinMux registers */ + }; + +Example pinmux entries: + + pinctrl { + sdmmc4_default: pinmux { + sdmmc4_clk_pcc4 { + nvidia,pins = "sdmmc4_clk_pcc4", + nvidia,function = "sdmmc4"; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + }; + + sdmmc4_dat0_paa0 { + nvidia,pins = "sdmmc4_dat0_paa0", + "sdmmc4_dat1_paa1", + "sdmmc4_dat2_paa2", + "sdmmc4_dat3_paa3", + "sdmmc4_dat4_paa4", + "sdmmc4_dat5_paa5", + "sdmmc4_dat6_paa6", + "sdmmc4_dat7_paa7"; + nvidia,function = "sdmmc4"; + nvidia,pull = <TEGRA_PIN_PULL_UP>; + nvidia,tristate = <TEGRA_PIN_DISABLE>; + }; + }; + }; + + sdhci@78000400 { + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc4_default>; + };
Signature · 1 line
1.7.1.1
PATCH v3 2/2 pinctrl: tegra: add pinmux controller driver for Tegra124
From: Ashwini Ghuge <[email protected]>
This adds a driver for the Tegra124 pinmux, and required parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs, hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.
---
Changes from V1:
- Lots of cleanups and fixes for string separator by Thierry.
- Fixes for some of group entries.
Changes from V2:
- remove extra space.
- Added Ack and Tested by: Stephen and cc to Thierry.
drivers/pinctrl/Kconfig | 4 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-tegra124.c | 3137 ++++++++++++++++++++++++++++++++++++ 3 files changed, 3142 insertions(+), 0 deletions(-) create mode 100644 drivers/pinctrl/pinctrl-tegra124.c
drivers/pinctrl/Kconfig +4 -0
@@ -269,6 +269,10 @@ config PINCTRL_TEGRA114 bool select PINCTRL_TEGRA +config PINCTRL_TEGRA124 + bool + select PINCTRL_TEGRA + config PINCTRL_TZ1090 bool "Toumaz Xenif TZ1090 pin control driver" depends on SOC_TZ1090
drivers/pinctrl/Makefile +1 -0
@@ -49,6 +49,7 @@ obj-$(CONFIG_PINCTRL_TEGRA) += pinctrl-tegra.o obj-$(CONFIG_PINCTRL_TEGRA20) += pinctrl-tegra20.o obj-$(CONFIG_PINCTRL_TEGRA30) += pinctrl-tegra30.o obj-$(CONFIG_PINCTRL_TEGRA114) += pinctrl-tegra114.o +obj-$(CONFIG_PINCTRL_TEGRA124) += pinctrl-tegra124.o obj-$(CONFIG_PINCTRL_TZ1090) += pinctrl-tz1090.o obj-$(CONFIG_PINCTRL_TZ1090_PDC) += pinctrl-tz1090-pdc.o obj-$(CONFIG_PINCTRL_U300) += pinctrl-u300.o
drivers/pinctrl/pinctrl-tegra124.c new file +3137 -0
2,983 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
1.7.1.1
Part of the diff is not shown here. View the raw message.
Linus Walleij
AppliedRe: [PATCH V3 2/2] pinctrl: tegra: add pinmux controller driver for Tegra124
Quoted 23 lines · Laxman Dewangan
From: Ashwini Ghuge <[email protected]>
This adds a driver for the Tegra124 pinmux, and required parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs, hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.Signed-off-by Ashwini Ghuge <[email protected]>Signed-off-by Laxman Dewangan <[email protected]>Acked-by Stephen Warren <[email protected]>Tested-by Stephen Warren <[email protected]>CC Thierry Reding <[email protected]>
Quoted 7 lines
---
Changes from V1:
- Lots of cleanups and fixes for string separator by Thierry.
- Fixes for some of group entries.
Changes from V2:
- remove extra space.
- Added Ack and Tested by: Stephen and cc to Thierry.
Applied this v3 version, thanks!
Yours,
Linus Walleij
Quoted 6 lines · Laxman Dewangan
This device tree binding document describes the Tegra124 pincontrol DT bindings. This document lists all valid properties, names, mux options of Tegra124 pins.
Signed-off-by Laxman Dewangan <[email protected]>Acked-by Stephen Warren <[email protected]>
Just to be clear: My acks on this series are valid, and I think this series should be merged.
Linus Walleij
AppliedQuoted 6 lines · Laxman Dewangan
This device tree binding document describes the Tegra124 pincontrol DT bindings. This document lists all valid properties, names, mux options of Tegra124 pins.
Signed-off-by Laxman Dewangan <[email protected]>Acked-by Stephen Warren <[email protected]>
Quoted 7 lines
---
Changes from V1:
- Referred the dt-binding header file on describing the nodes.Changes from V2:
- Rewording reg properties.
- dropdrv_typeas it is not applicable.
Applied this v3 version, thanks!
Yours,
Linus Walleij