Display adjacent switch port's attributes
Subsystems (3)
PATCH 1/1 Display adjacent switch port's attributes
This patch adds a new option to ethtool to display the adjacent switch port's attributes, as perceived by the NIC, e.g. through respective LLDP message exchanges.
Best regards,
Stefan Raspl
Stefan Raspl (1):
ethtool: Add option '-q' to display adjacent switch port's attributes
ethtool-copy.h | 35 ++++++++++++++++++++++++++++++ ethtool.8.in | 6 ++++++ ethtool.c | 68 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 109 insertions(+)
Signature · 1 line
1.8.3.4
PATCH 1/1 ethtool: Add option '-q' to display adjacent switch port's attributes
Add new option '-q|--query-switch-port' to display information on the adjacent switch port's settings as perceived by the respective NIC. In the output,
- unsupported attributes are indicated as such ('unsupported'),
- supported but disabled attributes display 'no', and
- enabled attributes display 'yes'.
Attributes supported by this patch are
- forwarding modes:
standard (802.1) and reflective relay (RR) aka hairpin
- edge virtual bridging (EVB) related capabilities:
edge control protocol (ECP), VSI discovery and configuration protocol (VDP), and retransmission timer exponent (RTE).
--- ethtool-copy.h | 35 ++++++++++++++++++++++++++++++ ethtool.8.in | 6 ++++++ ethtool.c | 68 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 109 insertions(+)
ethtool-copy.h +35 -0
@@ -348,6 +348,22 @@ struct ethtool_pauseparam {__u32 tx_pause; }; +/** +* struct ethtool_swport_attrs - query adjacent switch port attributes +* @cmd: ETHTOOL_GPORT +* @port_rc: Use GPORT_RC_* as appropriate. +* @supported: Forwarding modes and capabilities supported by the switch port, +* see SUPPORTED_SP_* flags. +* @enabled: Forwarding modes and capabilities currently activated at the +* adjacent switch port, see ENABLED_SP_* flags. +*/ +struct ethtool_swport_attrs { +__u32 cmd; +__u32 port_rc; +__u32 supported; +__u32 enabled; +}; +#define ETH_GSTRING_LEN 32enum ethtool_stringset {ETH_SS_TEST =0 ,
@@ -900,6 +916,7 @@ enum ethtool_sfeatures_retval_bits {#define ETHTOOL_GMODULEEEPROM 0x00000043/* Get plug-in module eeprom */ #define ETHTOOL_GEEE 0x00000044/* Get EEE settings */ #define ETHTOOL_SEEE 0x00000045/* Set EEE settings */ +#define ETHTOOL_GPORT 0x00000046/* Get switch port attributes */ /* compatibility with older code */ #define SPARC_ETH_GSET ETHTOOL_GSET
@@ -1067,6 +1084,24 @@ enum ethtool_sfeatures_retval_bits {#define ETH_MODULE_SFF_8472 0x2#define ETH_MODULE_SFF_8472_LEN 512 +/* Bad return codes for switch ports */ +#define GPORT_RC_LLDP_UNSUP 1/* switch port doesn't support */ +/* required LLDP EVB TLV */ + +/* Indicates what features the adjacent switch port supports. */ +#define SUPPORTED_SP_FWD_802_1 (1 << 0) +#define SUPPORTED_SP_FWD_RR (1 << 1) +#define SUPPORTED_SP_CAP_RTE (1 << 9) +#define SUPPORTED_SP_CAP_ECP (1 << 10) +#define SUPPORTED_SP_CAP_VDP (1 << 11) + +/* Indicates what features the adjacent switch port has enabled. */ +#define ENABLED_SP_FWD_802_1 (1 << 0) +#define ENABLED_SP_FWD_RR (1 << 1) +#define ENABLED_SP_CAP_RTE (1 << 9) +#define ENABLED_SP_CAP_ECP (1 << 10) +#define ENABLED_SP_CAP_VDP (1 << 11) +/* Reset flags */ /* The reset() operation must clear the flags for the components which * were actually reset. On successful return, the flags indicate the
ethtool.8.in +6 -0
@@ -214,6 +214,9 @@ ethtool \- query or control network driver and hardware settings .B ethtool \-P|\-\-show\-permaddr .I devname .HP +.B ethtool \-q|\-\-query-switch-port +.I devname +.HP .B ethtool \-r|\-\-negotiate .I devname .HP
@@ -483,6 +486,9 @@ Length of time to perform phys-id, in seconds. .B \-P \-\-show\-permaddr Queries the specified network device for permanent hardware address. .TP +.B \-q \-\-query-switch-port +Queries the specified Ethernet device for adjacent switch port's attributes. +.TP .B \-r \-\-negotiate Restarts auto-negotiation on the specified Ethernet device, if auto-negotiation is enabled.
ethtool.c +68 -0
86 lines not on this page · raw message
Signature · 1 line
1.8.3.4