Input: pixcir_i2c_ts: Add Type-B Multitouch support
Subsystems (3)
cover Input: pixcir_i2c_ts: Add Type-B Multitouch support
Hi,
Some variants of the Pixcir I2C touch controller are more suitable for Type-B multi-touch reporting (e.g. Tango C). This series enhances the driver to support Type-B multi-touch reports. It also adds device tree support and power management.
cheers,
-roger
Roger Quadros (9):
Input: pixcir_i2c_ts: Add device tree support
Input: pixcir_i2c_ts: Add register definitions
Input: pixcir_i2c_ts: Initialize interrupt mode and power mode
Input: pixcir_i2c_ts: Use devres managed resource allocations
Input: pixcir_i2c_ts: Get rid of pdata->attb_read_val()
Input: pixcir_i2c_ts: Add chip specific data structure
Input: pixcir_i2c_ts: Implement Type B Multi Touch reporting
Input: pixcir_i2c_ts: Add support for TangoC family
Input: pixcir_i2c_ts: Implement wakeup from suspend
.../bindings/input/touchscreen/pixcir_i2c_ts.txt | 26 + drivers/input/touchscreen/pixcir_i2c_ts.c | 570 +++++++++++++++++---- include/linux/input/pixcir_ts.h | 59 ++- 3 files changed, 564 insertions(+), 91 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt
Signature · 1 line
1.8.3.2
PATCH 1/9 Input: pixcir_i2c_ts: Add device tree support
Provide device tree support and binding information. Change platform data parameters from x/y_max to x/y_size..
--- .../bindings/input/touchscreen/pixcir_i2c_ts.txt | 26 ++++++++ drivers/input/touchscreen/pixcir_i2c_ts.c | 77 ++++++++++++++++++++-- include/linux/input/pixcir_ts.h | 5 +- 3 files changed, 101 insertions(+), 7 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt
Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file +26 -0
@@ -0,0 +1,26 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + };
drivers/input/touchscreen/pixcir_i2c_ts.c +72 -5
114 lines not on this page · raw message
include/linux/input/pixcir_ts.h +3 -2
@@ -3,8 +3,9 @@struct pixcir_ts_platform_data {int (*attb_read_val)(void ); -int x_max; -int y_max; +unsigned int x_size;/* X axis resolution */ +unsigned int y_size;/* Y axis resolution */ +int gpio_attb;/* GPIO connected to ATTB line */ };#endif
Signature · 1 line
1.8.3.2
Dmitry Torokhov
maintainerRe: [PATCH 1/9] Input: pixcir_i2c_ts: Add device tree support
Hi Roger,
Quoted 2 lines · Roger Quadros
Provide device tree support and binding information. Change platform data parameters from x/y_max to x/y_size..
I'd rather keep them as they were.
Quoted 58 lines
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- .../bindings/input/touchscreen/pixcir_i2c_ts.txt | 26 ++++++++ drivers/input/touchscreen/pixcir_i2c_ts.c | 77 ++++++++++++++++++++-- include/linux/input/pixcir_ts.h | 5 +- 3 files changed, 101 insertions(+), 7 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txtDocumentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file +26
-0@@ -0,0 +1,26 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + };drivers/input/touchscreen/pixcir_i2c_ts.c +4
-0@@ -24,6 +24,10 @@#include <linux/i2c.h> #include <linux/input.h> #include <linux/input/pixcir_ts.h> +#include <linux/gpio.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_device.h> struct pixcir_i2c_ts_data {struct i2c_client *client;
drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 132
Quoted 4 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +1
-0@@ -125,15 +129,65 @@ static int pixcir_i2c_ts_resume(struct device *dev) static SIMPLE_DEV_PM_OPS(pixcir_dev_pm_ops, pixcir_i2c_ts_suspend, pixcir_i2c_ts_resume); +#if defined(CONFIG_OF )
#ifdef is preferred for simple conditions.
drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 143
Quoted 11 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +11
-0+static const struct of_device_id pixcir_of_match[]; + +static struct pixcir_ts_platform_data *pixcir_parse_dt (struct device *dev) +{ +struct pixcir_ts_platform_data *pdata; +struct device_node *np = dev->of_node; +const struct of_device_id *match; + + match =of_match_device (of_match_ptr (pixcir_of_match), dev); +if (!match) +return ERR_PTR (-EINVAL );
Why do you need an explicit match here?
Quoted 18 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +18
-0+ + pdata =devm_kzalloc (dev,sizeof (*pdata),GFP_KERNEL ); +if (!pdata) +return ERR_PTR (-ENOMEM ); + + pdata->gpio_attb =of_get_named_gpio (np,"attb-gpio" ,0 ); +if (!gpio_is_valid (pdata->gpio_attb)) +dev_err (dev,"Failed to get ATTB GPIO\n" ); + +if (of_property_read_u32 (np,"x-size" , &pdata->x_size)) { +dev_err (dev,"Failed to get x-size property\n" ); +return ERR_PTR (-EINVAL ); + } + +if (of_property_read_u32 (np,"y-size" , &pdata->y_size)) { +dev_err (dev,"Failed to get y-size property\n" ); +return ERR_PTR (-EINVAL ); + }
drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 171
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +10
-0+ +dev_dbg (dev,"%s: x %d, y %d, gpio %d\n" , __func__, + pdata->x_size, pdata->y_size, pdata->gpio_attb); + + return pdata; +} +#else +static struct pixcir_ts_platform_data *pixcir_parse_dt (struct device *dev) +{ +return NULL ;
This should be
return ERR_PTR(-EINVAL);
since you test it with IS_ERR() later.
Quoted 8 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +4
-0+} +#endif +static int pixcir_i2c_ts_probe (struct i2c_client *client,const struct i2c_device_id *id) {const struct pixcir_ts_platform_data *pdata = client->dev.platform_data; +struct device *dev = &client->dev;
drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 188
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +5
-1+struct device_node *np = dev->of_node;struct pixcir_i2c_ts_data *tsdata;struct input_dev *input;int error; -if (!pdata) { +if (np) { + pdata =pixcir_parse_dt (dev); +if (IS_ERR (pdata)) +return PTR_ERR (pdata);
We should be favoring kernel-provided platform data if it is pesent even if there is dt-data available. This way user can override firmware,m if needed.
Quoted 25 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +10
-4+ + }else if (!pdata) {dev_err (&client->dev,"platform data not defined\n" );return -EINVAL ; }@@ -157,10 +211,14 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,__set_bit (EV_KEY , input->evbit);__set_bit (EV_ABS , input->evbit);__set_bit (BTN_TOUCH , input->keybit); -input_set_abs_params (input,ABS_X ,0 , pdata->x_max,0 ,0 ); -input_set_abs_params (input,ABS_Y ,0 , pdata->y_max,0 ,0 ); -input_set_abs_params (input,ABS_MT_POSITION_X ,0 , pdata->x_max,0 ,0 ); -input_set_abs_params (input,ABS_MT_POSITION_Y ,0 , pdata->y_max,0 ,0 ); +input_set_abs_params (input,ABS_X , +0 , pdata->x_size -1 ,0 ,0 ); +input_set_abs_params (input,ABS_Y , +0 , pdata->y_size -1 ,0 ,0 ); +input_set_abs_params (input,ABS_MT_POSITION_X , +0 , pdata->x_size -1 ,0 ,0 ); +input_set_abs_params (input,ABS_MT_POSITION_Y , +0 , pdata->y_size -1 ,0 ,0 );input_set_drvdata (input, tsdata);
drivers/input/touchscreen/pixcir_i2c_ts.c static const struct i2c_device_id pixcir_i2c_ts_id[] = { · line 278
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +7
-0@@ -211,11 +269,20 @@ static const struct i2c_device_id pixcir_i2c_ts_id[] = { };MODULE_DEVICE_TABLE (i2c, pixcir_i2c_ts_id); +#if defined(CONFIG_OF ) +static const struct of_device_id pixcir_of_match[] = { + { .compatible ="pixcir,pixcir_ts" , }, + { } +}; +MODULE_DEVICE_TABLE (of, pixcir_of_match); +#endif
#ifdef is preferred for simple conditions.
Quoted 15 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +2
-0+static struct i2c_driver pixcir_i2c_ts_driver = { .driver = { .owner =THIS_MODULE , .name ="pixcir_ts" , .pm = &pixcir_dev_pm_ops, + .of_match_table =of_match_ptr (pixcir_of_match), }, .probe = pixcir_i2c_ts_probe, .remove = pixcir_i2c_ts_remove,include/linux/input/pixcir_ts.h +0
-0
include/linux/input/pixcir_ts.h line 9
Quoted 9 lines
include/linux/input/pixcir_ts.h +3
-2@@ -3,8 +3,9 @@struct pixcir_ts_platform_data {int (*attb_read_val)(void ); -int x_max; -int y_max; +unsigned int x_size;/* X axis resolution */ +unsigned int y_size;/* Y axis resolution */ +int gpio_attb;/* GPIO connected to ATTB line */ };
OK, it looks like the series were split awkwardly: you are defining data that is used by follow-up patches and its purpose is unclear when reviewing patch-by-patch. I'd recommend rearranging so that DT support patch is the very last in the series.
Quoted 5 lines
include/linux/input/pixcir_ts.h +0
-0#endif Signature · 1 line
1.8.3.2
Thanks.
Signature · 1 line
Dmitry
Re: [PATCH 1/9] Input: pixcir_i2c_ts: Add device tree support
Quoted 7 lines · Dmitry Torokhov
Hi Roger,
Quoted 2 lines · Roger Quadros
Provide device tree support and binding information. Change platform data parameters from x/y_max to x/y_size..
I'd rather keep them as they were.
OK.
Quoted 66 lines
Quoted 59 lines
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- .../bindings/input/touchscreen/pixcir_i2c_ts.txt | 26 ++++++++ drivers/input/touchscreen/pixcir_i2c_ts.c | 77 ++++++++++++++++++++-- include/linux/input/pixcir_ts.h | 5 +- 3 files changed, 101 insertions(+), 7 deletions(-) create mode 100644 Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txtDocumentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt new file +26
-0@@ -0,0 +1,26 @@ +* Pixcir I2C touchscreen controllers + +Required properties: +- compatible: must be "pixcir,pixcir_ts" +- reg: I2C address of the chip +- interrupts: interrupt to which the chip is connected +- attb-gpio: GPIO connected to the ATTB line of the chip +- x-size: horizontal resolution of touchscreen +- y-size: vertical resolution of touchscreen + +Example: + + i2c@00000000 { + /* ... */ + + pixcir_ts@5c { + compatible = "pixcir,pixcir_ts"; + reg = <0x5c>; + interrupts = <2 0>; + attb-gpio = <&gpf 2 0 2>; + x-size = <800>; + y-size = <600>; + }; + + /* ... */ + };drivers/input/touchscreen/pixcir_i2c_ts.c +4
-0@@ -24,6 +24,10 @@#include <linux/i2c.h> #include <linux/input.h> #include <linux/input/pixcir_ts.h> +#include <linux/gpio.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_device.h> struct pixcir_i2c_ts_data {struct i2c_client *client;drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 132
Quoted 4 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +1
-0@@ -125,15 +129,65 @@ static int pixcir_i2c_ts_resume(struct device *dev) static SIMPLE_DEV_PM_OPS(pixcir_dev_pm_ops, pixcir_i2c_ts_suspend, pixcir_i2c_ts_resume); +#if defined(CONFIG_OF )#ifdef is preferred for simple conditions.
Quoted 14 lines
drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 143
Quoted 11 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +11
-0+static const struct of_device_id pixcir_of_match[]; + +static struct pixcir_ts_platform_data *pixcir_parse_dt (struct device *dev) +{ +struct pixcir_ts_platform_data *pdata; +struct device_node *np = dev->of_node; +const struct of_device_id *match; + + match =of_match_device (of_match_ptr (pixcir_of_match), dev); +if (!match) +return ERR_PTR (-EINVAL );Why do you need an explicit match here?
Right, it is not needed here for this patch but used later in patch 6 to get chip specific data. I'll fix this while re-arranging the patches.
Quoted 31 lines
Quoted 18 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +18
-0+ + pdata =devm_kzalloc (dev,sizeof (*pdata),GFP_KERNEL ); +if (!pdata) +return ERR_PTR (-ENOMEM ); + + pdata->gpio_attb =of_get_named_gpio (np,"attb-gpio" ,0 ); +if (!gpio_is_valid (pdata->gpio_attb)) +dev_err (dev,"Failed to get ATTB GPIO\n" ); + +if (of_property_read_u32 (np,"x-size" , &pdata->x_size)) { +dev_err (dev,"Failed to get x-size property\n" ); +return ERR_PTR (-EINVAL ); + } + +if (of_property_read_u32 (np,"y-size" , &pdata->y_size)) { +dev_err (dev,"Failed to get y-size property\n" ); +return ERR_PTR (-EINVAL ); + }drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 171
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +10
-0+ +dev_dbg (dev,"%s: x %d, y %d, gpio %d\n" , __func__, + pdata->x_size, pdata->y_size, pdata->gpio_attb); + + return pdata; +} +#else +static struct pixcir_ts_platform_data *pixcir_parse_dt (struct device *dev) +{ +return NULL ;This should be
Quoted 3 lines
return ERR_PTR(-EINVAL);since you test it with
IS_ERR()later.
OK.
Quoted 14 lines
Quoted 14 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +5
-0+} +#endif +static int pixcir_i2c_ts_probe (struct i2c_client *client,const struct i2c_device_id *id) {const struct pixcir_ts_platform_data *pdata = client->dev.platform_data; +struct device *dev = &client->dev; +struct device_node *np = dev->of_node;struct pixcir_i2c_ts_data *tsdata;struct input_dev *input;int error;
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c static int pixcir_i2c_ts_resume(struct device *dev) · line 188
Quoted 5 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +4
-1-if (!pdata) { +if (np) { + pdata =pixcir_parse_dt (dev); +if (IS_ERR (pdata)) +return PTR_ERR (pdata);We should be favoring kernel-provided platform data if it is pesent even if there is dt-data available. This way user can override firmware,m if needed.
OK. But how can the user override kernel provided platform data? Can't device tree overlays be used to patch DT data in the same fashion.
I've not tried either so I don't know which one is more user friendly.
Quoted 28 lines
Quoted 28 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +10
-4+ + }else if (!pdata) {dev_err (&client->dev,"platform data not defined\n" );return -EINVAL ; }@@ -157,10 +211,14 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,__set_bit (EV_KEY , input->evbit);__set_bit (EV_ABS , input->evbit);__set_bit (BTN_TOUCH , input->keybit); -input_set_abs_params (input,ABS_X ,0 , pdata->x_max,0 ,0 ); -input_set_abs_params (input,ABS_Y ,0 , pdata->y_max,0 ,0 ); -input_set_abs_params (input,ABS_MT_POSITION_X ,0 , pdata->x_max,0 ,0 ); -input_set_abs_params (input,ABS_MT_POSITION_Y ,0 , pdata->y_max,0 ,0 ); +input_set_abs_params (input,ABS_X , +0 , pdata->x_size -1 ,0 ,0 ); +input_set_abs_params (input,ABS_Y , +0 , pdata->y_size -1 ,0 ,0 ); +input_set_abs_params (input,ABS_MT_POSITION_X , +0 , pdata->x_size -1 ,0 ,0 ); +input_set_abs_params (input,ABS_MT_POSITION_Y , +0 , pdata->y_size -1 ,0 ,0 );input_set_drvdata (input, tsdata);@@ -211,11 +269,20 @@ static const struct i2c_device_id pixcir_i2c_ts_id[] = { };MODULE_DEVICE_TABLE (i2c, pixcir_i2c_ts_id);
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c static const struct i2c_device_id pixcir_i2c_ts_id[] = { · line 278
Quoted 7 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +7
-0+#if defined(CONFIG_OF ) +static const struct of_device_id pixcir_of_match[] = { + { .compatible ="pixcir,pixcir_ts" , }, + { } +}; +MODULE_DEVICE_TABLE (of, pixcir_of_match); +#endif #ifdef is preferred for simple conditions.
OK.
Quoted 16 lines
Quoted 16 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +2
-0+static struct i2c_driver pixcir_i2c_ts_driver = { .driver = { .owner =THIS_MODULE , .name ="pixcir_ts" , .pm = &pixcir_dev_pm_ops, + .of_match_table =of_match_ptr (pixcir_of_match), }, .probe = pixcir_i2c_ts_probe, .remove = pixcir_i2c_ts_remove,include/linux/input/pixcir_ts.h +0
-0@@ -3,8 +3,9 @@
Quoted 14 lines
include/linux/input/pixcir_ts.h line 9
Quoted 8 lines
include/linux/input/pixcir_ts.h +3
-2struct pixcir_ts_platform_data {int (*attb_read_val)(void ); -int x_max; -int y_max; +unsigned int x_size;/* X axis resolution */ +unsigned int y_size;/* Y axis resolution */ +int gpio_attb;/* GPIO connected to ATTB line */ };OK, it looks like the series were split awkwardly: you are defining data that is used by follow-up patches and its purpose is unclear when reviewing patch-by-patch. I'd recommend rearranging so that DT support patch is the very last in the series.
Got it.
Quoted 4 lines
Quoted 4 lines
include/linux/input/pixcir_ts.h +0
-0#endif Signature · 1 line
1.8.3.2
cheers,
-roger
PATCH 2/9 Input: pixcir_i2c_ts: Add register definitions
In reply to Roger QuadrosAdd power and interrupt register definitions.
--- include/linux/input/pixcir_ts.h | 42 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+)
include/linux/input/pixcir_ts.h +42 -0
@@ -1,6 +1,48 @@ #ifndef _PIXCIR_I2C_TS_H #define _PIXCIR_I2C_TS_H +/* + * Register map + */ +#define PIXCIR_REG_POWER_MODE 51 +#define PIXCIR_REG_INT_MODE 52 + +/* + * Power modes: + * active: max scan speed + * idle: lower scan speed with automatic transition to active on touch + * halt: datasheet says sleep but this is more like halt as the chip + * clocks are cut and it can only be brought out of this mode + * using the RESET pin. + */ +enum pixcir_power_mode { + PIXCIR_POWER_ACTIVE, + PIXCIR_POWER_IDLE, + PIXCIR_POWER_HALT, +}; + +#define PIXCIR_POWER_MODE_MASK 0x03 +#define PIXCIR_POWER_ALLOW_IDLE (1UL << 2) + +/* + * Interrupt modes: + * periodical: interrupt is asserted periodicaly + * diff coordinates: interrupt is asserted when coordinates change + * level on touch: interrupt level asserted during touch + * pulse on touch: interrupt pulse asserted druing touch + * + */ +enum pixcir_int_mode { + PIXCIR_INT_PERIODICAL, + PIXCIR_INT_DIFF_COORD, + PIXCIR_INT_LEVEL_TOUCH, + PIXCIR_INT_PULSE_TOUCH, +}; + +#define PIXCIR_INT_MODE_MASK 0x03 +#define PIXCIR_INT_ENABLE (1UL << 3) +#define PIXCIR_INT_POL_HIGH (1UL << 2) + struct pixcir_ts_platform_data { int (*attb_read_val)(void); unsigned int x_size; /* X axis resolution */
Signature · 1 line
1.8.3.2
Dmitry Torokhov
maintainerRe: [PATCH 2/9] Input: pixcir_i2c_ts: Add register definitions
Quoted 2 lines · Roger Quadros
Add power and interrupt register definitions.
Please fold into the next patch that uses these definitions.
Quoted 62 lines
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- include/linux/input/pixcir_ts.h | 42 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+)include/linux/input/pixcir_ts.h +42
-0@@ -1,6 +1,48 @@ #ifndef _PIXCIR_I2C_TS_H #define _PIXCIR_I2C_TS_H +/* + * Register map + */ +#define PIXCIR_REG_POWER_MODE 51 +#define PIXCIR_REG_INT_MODE 52 + +/* + * Power modes: + * active: max scan speed + * idle: lower scan speed with automatic transition to active on touch + * halt: datasheet says sleep but this is more like halt as the chip + * clocks are cut and it can only be brought out of this mode + * using the RESET pin. + */ +enum pixcir_power_mode { + PIXCIR_POWER_ACTIVE, + PIXCIR_POWER_IDLE, + PIXCIR_POWER_HALT, +}; + +#define PIXCIR_POWER_MODE_MASK 0x03 +#define PIXCIR_POWER_ALLOW_IDLE (1UL << 2) + +/* + * Interrupt modes: + * periodical: interrupt is asserted periodicaly + * diff coordinates: interrupt is asserted when coordinates change + * level on touch: interrupt level asserted during touch + * pulse on touch: interrupt pulse asserted druing touch + * + */ +enum pixcir_int_mode { + PIXCIR_INT_PERIODICAL, + PIXCIR_INT_DIFF_COORD, + PIXCIR_INT_LEVEL_TOUCH, + PIXCIR_INT_PULSE_TOUCH, +}; + +#define PIXCIR_INT_MODE_MASK 0x03 +#define PIXCIR_INT_ENABLE (1UL << 3) +#define PIXCIR_INT_POL_HIGH (1UL << 2) + struct pixcir_ts_platform_data { int (*attb_read_val)(void); unsigned int x_size; /* X axis resolution */Signature · 1 line
1.8.3.2
Signature · 1 line
Dmitry
PATCH 3/9 Input: pixcir_i2c_ts: Initialize interrupt mode and power mode
In reply to Roger QuadrosIntroduce helper functions to configure power and interrupt registers. Default to IDLE mode on probe as device supports auto wakeup to ACVIE mode on detecting finger touch.
Configure interrupt mode and polarity on start up.
--- drivers/input/touchscreen/pixcir_i2c_ts.c | 168 ++++++++++++++++++++++++++++++ 1 file changed, 168 insertions(+)
drivers/input/touchscreen/pixcir_i2c_ts.c +168 -0
@@ -104,6 +104,160 @@ static irqreturn_t pixcir_ts_isr(int irq, void *dev_id)return IRQ_HANDLED ; } +static int pixcir_set_power_mode (struct pixcir_i2c_ts_data *ts, +enum pixcir_power_mode mode) +{ +struct device *dev = &ts->client->dev; +int ret; + + ret =i2c_smbus_read_byte_data (ts->client,PIXCIR_REG_POWER_MODE ); +if (ret <0 ) { +dev_err (dev,"%s: can't read reg 0x%x : %d\n" , + __func__,PIXCIR_REG_POWER_MODE , ret); +return ret; + } + + ret &= ~PIXCIR_POWER_MODE_MASK ; + ret |= mode; + +/* Always AUTO_IDLE */ + ret |=PIXCIR_POWER_ALLOW_IDLE ; + + ret =i2c_smbus_write_byte_data (ts->client,PIXCIR_REG_POWER_MODE , ret); +if (ret <0 ) { +dev_err (dev,"%s: can't write reg 0x%x : %d\n" , + __func__,PIXCIR_REG_POWER_MODE , ret); +return ret; + } + +return 0 ; +} + +/* +* Set the interrupt mode for the device i.e. ATTB line behaviour +* +* @polarity : 1 for active high, 0 for active low. +*/ +static int pixcir_set_int_mode (struct pixcir_i2c_ts_data *ts, +enum pixcir_int_mode mode, +bool polarity) +{ +struct device *dev = &ts->client->dev; +int ret; + + ret =i2c_smbus_read_byte_data (ts->client,PIXCIR_REG_INT_MODE ); +if (ret <0 ) { +dev_err (dev,"%s: can't read reg 0x%x : %d\n" , + __func__,PIXCIR_REG_INT_MODE , ret); +return ret; + } + + ret &= ~PIXCIR_INT_MODE_MASK ; + ret |= mode; + +if (polarity) + ret |=PIXCIR_INT_POL_HIGH ; +else + ret &= ~PIXCIR_INT_POL_HIGH ; + + ret =i2c_smbus_write_byte_data (ts->client,PIXCIR_REG_INT_MODE , ret); +if (ret <0 ) { +dev_err (dev,"%s: can't write reg 0x%x : %d\n" , + __func__,PIXCIR_REG_INT_MODE , ret); +return ret; + } + +return 0 ; +} + +/* +* Enable/disable interrupt generation +*/ +static int pixcir_int_enable (struct pixcir_i2c_ts_data *ts,bool enable) +{ +struct device *dev = &ts->client->dev; +int ret; + + ret =i2c_smbus_read_byte_data (ts->client,PIXCIR_REG_INT_MODE ); +if (ret <0 ) { +dev_err (dev,"%s: can't read reg 0x%x : %d\n" , + __func__,PIXCIR_REG_INT_MODE , ret); +return ret; + } + +if (enable) + ret |=PIXCIR_INT_ENABLE ; +else + ret &= ~PIXCIR_INT_ENABLE ; + + ret =i2c_smbus_write_byte_data (ts->client,PIXCIR_REG_INT_MODE , ret); +if (ret <0 ) { +dev_err (dev,"%s: can't write reg 0x%x : %d\n" , + __func__,PIXCIR_REG_INT_MODE , ret); +return ret; + } + +return 0 ; +} + +static int pixcir_start (struct pixcir_i2c_ts_data *ts) +{ +struct device *dev = &ts->client->dev; +int ret; + +/* LEVEL_TOUCH interrupt with active low polarity */ + ret =pixcir_set_int_mode (ts,PIXCIR_INT_LEVEL_TOUCH ,0 ); +if (ret) { +dev_err (dev,"Failed to set interrupt mode\n" ); +return ret; + } + +enable_irq (ts->client->irq); + +/* enable interrupt generation */ + ret =pixcir_int_enable (ts,1 ); +if (ret) { +dev_err (dev,"Failed to enable interrupt generation\n" ); +return ret; + } + +return 0 ; +} + +static int pixcir_stop (struct pixcir_i2c_ts_data *ts) +{ +struct device *dev = &ts->client->dev; +int ret; + +/* disable interrupt generation */ + ret =pixcir_int_enable (ts,0 ); +if (ret) { +dev_err (dev,"Failed to disable interrupt generation\n" ); +return ret; + } + +disable_irq (ts->client->irq); + +return 0 ; +} + +static int pixcir_input_open (struct input_dev *dev) +{ +struct pixcir_i2c_ts_data *ts =input_get_drvdata (dev); + +return pixcir_start (ts); +} + +static void pixcir_input_close (struct input_dev *dev) +{ +struct pixcir_i2c_ts_data *ts =input_get_drvdata (dev); + +pixcir_stop (ts); + +return ; +} + +#ifdef CONFIG_PM_SLEEP static int pixcir_i2c_ts_suspend (struct device *dev) {
@@ -207,6 +361,8 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, input->name = client->name; input->id.bustype =BUS_I2C ; input->dev.parent = &client->dev; + input->open = pixcir_input_open; + input->close = pixcir_input_close;__set_bit (EV_KEY , input->evbit);__set_bit (EV_ABS , input->evbit);
@@ -230,6 +386,18 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, goto err_free_mem; } +/* Always be in IDLE mode to save power, device supports auto wake */ + error =pixcir_set_power_mode (tsdata,PIXCIR_POWER_IDLE ); +if (error) { +dev_err (dev,"Failed to set IDLE mode\n" ); +return error; + } + +/* Stop device till opened */ + error =pixcir_stop (tsdata); +if (error) + goto err_free_irq; + error =input_register_device (input);if (error) goto err_free_irq;
Signature · 1 line
1.8.3.2
Dmitry Torokhov
maintainerRe: [PATCH 3/9] Input: pixcir_i2c_ts: Initialize interrupt mode and power mode
Quoted 4 lines · Roger Quadros
drivers/input/touchscreen/pixcir_i2c_ts.c +4
-0+ +static int pixcir_stop (struct pixcir_i2c_ts_data *ts) +{ +struct device *dev = &ts->client->dev;
drivers/input/touchscreen/pixcir_i2c_ts.c static irqreturn_t pixcir_ts_isr(int irq, void *dev_id) · line 239
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +10
-0+int ret; + +/* disable interrupt generation */ + ret =pixcir_int_enable (ts,0 ); +if (ret) { +dev_err (dev,"Failed to disable interrupt generation\n" ); +return ret; + } + +disable_irq (ts->client->irq);
Why do you need to disable IRQ? If you disable interrupt generation in the chip I think you only need to call synchronize_irq() to make sure it's completed if it happens to be running. Also you need to move the code:
tsdata->exiting = true; mb();
here from pixcir_i2c_ts_remove() to make sure handler exits promptly.
You will also need to reset tsdata->exiting in your start method.
Thanks.
Signature · 5 lines
Dmitry -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 3/9] Input: pixcir_i2c_ts: Initialize interrupt mode and power mode
Quoted 12 lines · Dmitry Torokhov
Quoted 11 lines · Roger Quadros
drivers/input/touchscreen/pixcir_i2c_ts.c +11
-0+ +static int pixcir_stop (struct pixcir_i2c_ts_data *ts) +{ +struct device *dev = &ts->client->dev; +int ret; + +/* disable interrupt generation */ + ret =pixcir_int_enable (ts,0 ); +if (ret) { +dev_err (dev,"Failed to disable interrupt generation\n" ); +return ret;
Quoted 8 lines
drivers/input/touchscreen/pixcir_i2c_ts.c static irqreturn_t pixcir_ts_isr(int irq, void *dev_id) · line 239
Quoted 3 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +3
-0+ } + +disable_irq (ts->client->irq);Why do you need to disable IRQ? If you disable interrupt generation in the chip I think you only need to call
synchronize_irq()to make sure it's completed if it happens to be running. Also you need to move the code:
Agreed, no need to call disable_irq().
Quoted 8 lines
tsdata->exiting = true; mb();here from
pixcir_i2c_ts_remove()to make sure handler exits promptly.You will also need to reset
tsdata->exitingin your start method.
OK.
cheers,
-roger
PATCH 4/9 Input: pixcir_i2c_ts: Use devres managed resource allocations
In reply to Roger QuadrosUse devm_() and friends for allocating memory, input device and IRQ.
--- drivers/input/touchscreen/pixcir_i2c_ts.c | 35 ++++++++++++------------------- 1 file changed, 13 insertions(+), 22 deletions(-)
drivers/input/touchscreen/pixcir_i2c_ts.c +13 -22
@@ -346,12 +346,14 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,return -EINVAL ; } - tsdata =kzalloc (sizeof (*tsdata),GFP_KERNEL ); - input =input_allocate_device (); -if (!tsdata || !input) { -dev_err (&client->dev,"Failed to allocate driver data!\n" ); - error = -ENOMEM ; - goto err_free_mem; + tsdata =devm_kzalloc (dev,sizeof (*tsdata),GFP_KERNEL ); +if (!tsdata) +return -ENOMEM ; + + input =devm_input_allocate_device (dev); +if (!input) { +dev_err (&client->dev,"Failed to allocate input device\n" ); +return -ENOMEM ; } tsdata->client = client;
@@ -378,12 +380,12 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,input_set_drvdata (input, tsdata); - error =request_threaded_irq (client->irq,NULL , pixcir_ts_isr, + error =devm_request_threaded_irq (dev, client->irq,NULL , pixcir_ts_isr,IRQF_TRIGGER_FALLING |IRQF_ONESHOT , client->name, tsdata);if (error) { -dev_err (&client->dev,"Unable to request touchscreen IRQ.\n" ); - goto err_free_mem; +dev_err (dev,"failed to request irq %d\n" , client->irq); +return error; }/* Always be in IDLE mode to save power, device supports auto wake */
@@ -396,23 +398,16 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,/* Stop device till opened */ error =pixcir_stop (tsdata);if (error) - goto err_free_irq; +return error; error =input_register_device (input);if (error) - goto err_free_irq; +return error;i2c_set_clientdata (client, tsdata);device_init_wakeup (&client->dev,1 );return 0 ; - -err_free_irq: -free_irq (client->irq, tsdata); -err_free_mem: -input_free_device (input); -kfree (tsdata); -return error; }static int pixcir_i2c_ts_remove (struct i2c_client *client)
@@ -423,10 +418,6 @@ static int pixcir_i2c_ts_remove(struct i2c_client *client) tsdata->exiting = true;mb (); -free_irq (client->irq, tsdata); - -input_unregister_device (tsdata->input); -kfree (tsdata);return 0 ; }
Signature · 1 line
1.8.3.2
Dmitry Torokhov
maintainerRe: [PATCH 4/9] Input: pixcir_i2c_ts: Use devres managed resource allocations
Quoted 2 lines · Roger Quadros
Use
devm_()and friends for allocating memory, input device and IRQ.
This one looks good, maybe have it first in the series when you resubmit.
Quoted 88 lines
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- drivers/input/touchscreen/pixcir_i2c_ts.c | 35 ++++++++++++------------------- 1 file changed, 13 insertions(+), 22 deletions(-)drivers/input/touchscreen/pixcir_i2c_ts.c +13
-22@@ -346,12 +346,14 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,return -EINVAL ; } - tsdata =kzalloc (sizeof (*tsdata),GFP_KERNEL ); - input =input_allocate_device (); -if (!tsdata || !input) { -dev_err (&client->dev,"Failed to allocate driver data!\n" ); - error = -ENOMEM ; - goto err_free_mem; + tsdata =devm_kzalloc (dev,sizeof (*tsdata),GFP_KERNEL ); +if (!tsdata) +return -ENOMEM ; + + input =devm_input_allocate_device (dev); +if (!input) { +dev_err (&client->dev,"Failed to allocate input device\n" ); +return -ENOMEM ; } tsdata->client = client;@@ -378,12 +380,12 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,input_set_drvdata (input, tsdata); - error =request_threaded_irq (client->irq,NULL , pixcir_ts_isr, + error =devm_request_threaded_irq (dev, client->irq,NULL , pixcir_ts_isr,IRQF_TRIGGER_FALLING |IRQF_ONESHOT , client->name, tsdata);if (error) { -dev_err (&client->dev,"Unable to request touchscreen IRQ.\n" ); - goto err_free_mem; +dev_err (dev,"failed to request irq %d\n" , client->irq); +return error; }/* Always be in IDLE mode to save power, device supports auto wake */ @@ -396,23 +398,16 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,/* Stop device till opened */ error =pixcir_stop (tsdata);if (error) - goto err_free_irq; +return error; error =input_register_device (input);if (error) - goto err_free_irq; +return error;i2c_set_clientdata (client, tsdata);device_init_wakeup (&client->dev,1 );return 0 ; - -err_free_irq: -free_irq (client->irq, tsdata); -err_free_mem: -input_free_device (input); -kfree (tsdata); -return error; }static int pixcir_i2c_ts_remove (struct i2c_client *client)@@ -423,10 +418,6 @@ static int pixcir_i2c_ts_remove(struct i2c_client *client) tsdata->exiting = true;mb (); -free_irq (client->irq, tsdata); - -input_unregister_device (tsdata->input); -kfree (tsdata);return 0 ; }Signature · 1 line
1.8.3.2
Signature · 1 line
Dmitry
PATCH 5/9 Input: pixcir_i2c_ts: Get rid of pdata->attb_read_val()
In reply to Roger QuadrosGet rid of the attb_read_val() platform hook. Instead, read the ATTB gpio directly from the driver.
Fail if valid ATTB gpio is not provided by patform data.
--- drivers/input/touchscreen/pixcir_i2c_ts.c | 19 +++++++++++++++++-- include/linux/input/pixcir_ts.h | 1 - 2 files changed, 17 insertions(+), 3 deletions(-)
drivers/input/touchscreen/pixcir_i2c_ts.c +17 -2
@@ -91,11 +91,12 @@ static void pixcir_ts_poscheck(struct pixcir_i2c_ts_data *data)static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) {struct pixcir_i2c_ts_data *tsdata = dev_id; +const struct pixcir_ts_platform_data *pdata = tsdata->chip;while (!tsdata->exiting) {pixcir_ts_poscheck (tsdata); -if (tsdata->chip->attb_read_val ()) +if (gpio_get_value (pdata->gpio_attb))break ;msleep (20 );
@@ -301,8 +302,10 @@ static struct pixcir_ts_platform_data *pixcir_parse_dt(struct device *dev)return ERR_PTR (-ENOMEM ); pdata->gpio_attb =of_get_named_gpio (np,"attb-gpio" ,0 ); -if (!gpio_is_valid (pdata->gpio_attb)) +if (!gpio_is_valid (pdata->gpio_attb)) {dev_err (dev,"Failed to get ATTB GPIO\n" ); +return ERR_PTR (-EINVAL ); + }if (of_property_read_u32 (np,"x-size" , &pdata->x_size)) {dev_err (dev,"Failed to get x-size property\n" );
@@ -344,6 +347,11 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, }else if (!pdata) {dev_err (&client->dev,"platform data not defined\n" );return -EINVAL ; + }else { +if (!gpio_is_valid (pdata->gpio_attb)) { +dev_err (dev,"Invalid gpio_attb in pdata\n" ); +return -EINVAL ; + } } tsdata =devm_kzalloc (dev,sizeof (*tsdata),GFP_KERNEL );
@@ -380,6 +388,13 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,input_set_drvdata (input, tsdata); + error =devm_gpio_request_one (dev, pdata->gpio_attb, +GPIOF_DIR_IN ,"pixcir_i2c_attb" ); +if (error) { +dev_err (dev,"Failed to request ATTB gpio\n" ); +return error; + } + error =devm_request_threaded_irq (dev, client->irq,NULL , pixcir_ts_isr,IRQF_TRIGGER_FALLING |IRQF_ONESHOT , client->name, tsdata);
include/linux/input/pixcir_ts.h +0 -1
@@ -44,7 +44,6 @@ enum pixcir_int_mode {#define PIXCIR_INT_POL_HIGH (1UL << 2)struct pixcir_ts_platform_data { -int (*attb_read_val)(void );unsigned int x_size;/* X axis resolution */ unsigned int y_size;/* Y axis resolution */ int gpio_attb;/* GPIO connected to ATTB line */
Signature · 1 line
1.8.3.2
Dmitry Torokhov
maintainerRe: [PATCH 5/9] Input: pixcir_i2c_ts: Get rid of pdata->attb_read_val()
Quoted 4 lines · Roger Quadros
Get rid of the
attb_read_val()platform hook. Instead, read the ATTB gpio directly from the driver.Fail if valid ATTB gpio is not provided by patform data.
Do you also need to define polarity?
Quoted 79 lines
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- drivers/input/touchscreen/pixcir_i2c_ts.c | 19 +++++++++++++++++-- include/linux/input/pixcir_ts.h | 1 - 2 files changed, 17 insertions(+), 3 deletions(-)drivers/input/touchscreen/pixcir_i2c_ts.c +17
-2@@ -91,11 +91,12 @@ static void pixcir_ts_poscheck(struct pixcir_i2c_ts_data *data)static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) {struct pixcir_i2c_ts_data *tsdata = dev_id; +const struct pixcir_ts_platform_data *pdata = tsdata->chip;while (!tsdata->exiting) {pixcir_ts_poscheck (tsdata); -if (tsdata->chip->attb_read_val ()) +if (gpio_get_value (pdata->gpio_attb))break ;msleep (20 );@@ -301,8 +302,10 @@ static struct pixcir_ts_platform_data *pixcir_parse_dt(struct device *dev)return ERR_PTR (-ENOMEM ); pdata->gpio_attb =of_get_named_gpio (np,"attb-gpio" ,0 ); -if (!gpio_is_valid (pdata->gpio_attb)) +if (!gpio_is_valid (pdata->gpio_attb)) {dev_err (dev,"Failed to get ATTB GPIO\n" ); +return ERR_PTR (-EINVAL ); + }if (of_property_read_u32 (np,"x-size" , &pdata->x_size)) {dev_err (dev,"Failed to get x-size property\n" );@@ -344,6 +347,11 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, }else if (!pdata) {dev_err (&client->dev,"platform data not defined\n" );return -EINVAL ; + }else { +if (!gpio_is_valid (pdata->gpio_attb)) { +dev_err (dev,"Invalid gpio_attb in pdata\n" ); +return -EINVAL ; + } } tsdata =devm_kzalloc (dev,sizeof (*tsdata),GFP_KERNEL );@@ -380,6 +388,13 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,input_set_drvdata (input, tsdata); + error =devm_gpio_request_one (dev, pdata->gpio_attb, +GPIOF_DIR_IN ,"pixcir_i2c_attb" ); +if (error) { +dev_err (dev,"Failed to request ATTB gpio\n" ); +return error; + } + error =devm_request_threaded_irq (dev, client->irq,NULL , pixcir_ts_isr,IRQF_TRIGGER_FALLING |IRQF_ONESHOT , client->name, tsdata);include/linux/input/pixcir_ts.h +0
-1@@ -44,7 +44,6 @@ enum pixcir_int_mode {#define PIXCIR_INT_POL_HIGH (1UL << 2)struct pixcir_ts_platform_data { -int (*attb_read_val)(void );unsigned int x_size;/* X axis resolution */ unsigned int y_size;/* Y axis resolution */ int gpio_attb;/* GPIO connected to ATTB line */ Signature · 1 line
1.8.3.2
Signature · 1 line
Dmitry
Re: [PATCH 5/9] Input: pixcir_i2c_ts: Get rid of pdata->attb_read_val()
Quoted 8 lines · Dmitry Torokhov
Quoted 4 lines · Roger Quadros
Get rid of the
attb_read_val()platform hook. Instead, read the ATTB gpio directly from the driver.Fail if valid ATTB gpio is not provided by patform data.
Do you also need to define polarity?
In patch 3, in pixcir_start(), we explicitly configure the GPIO output polarity as /* LEVEL_TOUCH interrupt with active low polarity */
So I don't think we need to define polarity.
cheers,
-roger
Quoted 80 lines
Quoted 79 lines
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- drivers/input/touchscreen/pixcir_i2c_ts.c | 19 +++++++++++++++++-- include/linux/input/pixcir_ts.h | 1 - 2 files changed, 17 insertions(+), 3 deletions(-)drivers/input/touchscreen/pixcir_i2c_ts.c +17
-2@@ -91,11 +91,12 @@ static void pixcir_ts_poscheck(struct pixcir_i2c_ts_data *data)static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) {struct pixcir_i2c_ts_data *tsdata = dev_id; +const struct pixcir_ts_platform_data *pdata = tsdata->chip;while (!tsdata->exiting) {pixcir_ts_poscheck (tsdata); -if (tsdata->chip->attb_read_val ()) +if (gpio_get_value (pdata->gpio_attb))break ;msleep (20 );@@ -301,8 +302,10 @@ static struct pixcir_ts_platform_data *pixcir_parse_dt(struct device *dev)return ERR_PTR (-ENOMEM ); pdata->gpio_attb =of_get_named_gpio (np,"attb-gpio" ,0 ); -if (!gpio_is_valid (pdata->gpio_attb)) +if (!gpio_is_valid (pdata->gpio_attb)) {dev_err (dev,"Failed to get ATTB GPIO\n" ); +return ERR_PTR (-EINVAL ); + }if (of_property_read_u32 (np,"x-size" , &pdata->x_size)) {dev_err (dev,"Failed to get x-size property\n" );@@ -344,6 +347,11 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, }else if (!pdata) {dev_err (&client->dev,"platform data not defined\n" );return -EINVAL ; + }else { +if (!gpio_is_valid (pdata->gpio_attb)) { +dev_err (dev,"Invalid gpio_attb in pdata\n" ); +return -EINVAL ; + } } tsdata =devm_kzalloc (dev,sizeof (*tsdata),GFP_KERNEL );@@ -380,6 +388,13 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,input_set_drvdata (input, tsdata); + error =devm_gpio_request_one (dev, pdata->gpio_attb, +GPIOF_DIR_IN ,"pixcir_i2c_attb" ); +if (error) { +dev_err (dev,"Failed to request ATTB gpio\n" ); +return error; + } + error =devm_request_threaded_irq (dev, client->irq,NULL , pixcir_ts_isr,IRQF_TRIGGER_FALLING |IRQF_ONESHOT , client->name, tsdata);include/linux/input/pixcir_ts.h +0
-1@@ -44,7 +44,6 @@ enum pixcir_int_mode {#define PIXCIR_INT_POL_HIGH (1UL << 2)struct pixcir_ts_platform_data { -int (*attb_read_val)(void );unsigned int x_size;/* X axis resolution */ unsigned int y_size;/* Y axis resolution */ int gpio_attb;/* GPIO connected to ATTB line */ Signature · 1 line
1.8.3.2
PATCH 6/9 Input: pixcir_i2c_ts: Add chip specific data structure
In reply to Roger QuadrosThis is the data that differentiates different pixcir chips.
--- drivers/input/touchscreen/pixcir_i2c_ts.c | 8 +++++--- include/linux/input/pixcir_ts.h | 11 +++++++++++ 2 files changed, 16 insertions(+), 3 deletions(-)
drivers/input/touchscreen/pixcir_i2c_ts.c +5 -3
@@ -32,7 +32,7 @@struct pixcir_i2c_ts_data {struct i2c_client *client;struct input_dev *input; -const struct pixcir_ts_platform_data *chip; +const struct pixcir_ts_platform_data *pdata;bool exiting; };
@@ -91,7 +91,7 @@ static void pixcir_ts_poscheck(struct pixcir_i2c_ts_data *data)static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) {struct pixcir_i2c_ts_data *tsdata = dev_id; -const struct pixcir_ts_platform_data *pdata = tsdata->chip; +const struct pixcir_ts_platform_data *pdata = tsdata->pdata;while (!tsdata->exiting) {pixcir_ts_poscheck (tsdata);
@@ -301,6 +301,8 @@ static struct pixcir_ts_platform_data *pixcir_parse_dt(struct device *dev)if (!pdata)return ERR_PTR (-ENOMEM ); + pdata->chip = *(const struct pixcir_i2c_chip_data *)match->data; + pdata->gpio_attb =of_get_named_gpio (np,"attb-gpio" ,0 );if (!gpio_is_valid (pdata->gpio_attb)) {dev_err (dev,"Failed to get ATTB GPIO\n" );
@@ -366,7 +368,7 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, tsdata->client = client; tsdata->input = input; - tsdata->chip = pdata; + tsdata->pdata = pdata; input->name = client->name; input->id.bustype =BUS_I2C ;
include/linux/input/pixcir_ts.h +11 -0
@@ -43,10 +43,21 @@ enum pixcir_int_mode {#define PIXCIR_INT_ENABLE (1UL << 3)#define PIXCIR_INT_POL_HIGH (1UL << 2) +/** +* struct pixcir_irc_chip_data - chip related data +* @num_report_ids: Max number of finger ids reported simultaneously. +* if 0 it means chip doesn't support finger id reporting +* and driver will resort to Type A Multi-Touch reporting. +*/ +struct pixcir_i2c_chip_data { +u8 num_report_ids; +}; +struct pixcir_ts_platform_data {unsigned int x_size;/* X axis resolution */ unsigned int y_size;/* Y axis resolution */ int gpio_attb;/* GPIO connected to ATTB line */ +struct pixcir_i2c_chip_data chip; };#endif
Signature · 1 line
1.8.3.2
PATCH 7/9 Input: pixcir_i2c_ts: Implement Type B Multi Touch reporting
In reply to Roger QuadrosSome pixcir controllers e.g. tangoC family report finger IDs with the co-ordinates and are more suitable for Type-B MT protocol.
--- drivers/input/touchscreen/pixcir_i2c_ts.c | 202 +++++++++++++++++++++++------- 1 file changed, 155 insertions(+), 47 deletions(-)
drivers/input/touchscreen/pixcir_i2c_ts.c +155 -47
@@ -23,84 +23,173 @@#include <linux/slab.h> #include <linux/i2c.h> #include <linux/input.h> +#include <linux/input/mt.h> #include <linux/input/pixcir_ts.h> #include <linux/gpio.h> #include <linux/of.h> #include <linux/of_gpio.h> #include <linux/of_device.h> +#define MAX_FINGERS 5/* Maximum supported by the driver */ +struct pixcir_i2c_ts_data {struct i2c_client *client;struct input_dev *input;const struct pixcir_ts_platform_data *pdata;bool exiting; +u8 max_fingers;/* Maximum supported by the chip */ }; -static void pixcir_ts_poscheck (struct pixcir_i2c_ts_data *data) +static void pixcir_ts_typea_report (struct pixcir_i2c_ts_data *tsdata) { -struct pixcir_i2c_ts_data *tsdata = data; +const struct pixcir_ts_platform_data *pdata = tsdata->pdata;u8 rdbuf[10 ], wrbuf[1 ] = {0 };u8 touch;int ret; - ret =i2c_master_send (tsdata->client, wrbuf,sizeof (wrbuf)); -if (ret !=sizeof (wrbuf)) { -dev_err (&tsdata->client->dev, -"%s: i2c_master_send failed(), ret=%d\n" , - __func__, ret); -return ; - } +while (!tsdata->exiting) { - ret =i2c_master_recv (tsdata->client, rdbuf,sizeof (rdbuf)); -if (ret !=sizeof (rdbuf)) { -dev_err (&tsdata->client->dev, -"%s: i2c_master_recv failed(), ret=%d\n" , - __func__, ret); -return ; - } + ret =i2c_master_send (tsdata->client, wrbuf,sizeof (wrbuf)); +if (ret !=sizeof (wrbuf)) { +dev_err (&tsdata->client->dev, +"%s: i2c_master_send failed(), ret=%d\n" , + __func__, ret); +return ; + } + + ret =i2c_master_recv (tsdata->client, rdbuf,sizeof (rdbuf)); +if (ret !=sizeof (rdbuf)) { +dev_err (&tsdata->client->dev, +"%s: i2c_master_recv failed(), ret=%d\n" , + __func__, ret); +return ; + } - touch = rdbuf[0 ]; -if (touch) { -u16 posx1 = (rdbuf[3 ] <<8 ) | rdbuf[2 ]; -u16 posy1 = (rdbuf[5 ] <<8 ) | rdbuf[4 ]; -u16 posx2 = (rdbuf[7 ] <<8 ) | rdbuf[6 ]; -u16 posy2 = (rdbuf[9 ] <<8 ) | rdbuf[8 ]; - -input_report_key (tsdata->input,BTN_TOUCH ,1 ); -input_report_abs (tsdata->input,ABS_X , posx1); -input_report_abs (tsdata->input,ABS_Y , posy1); - -input_report_abs (tsdata->input,ABS_MT_POSITION_X , posx1); -input_report_abs (tsdata->input,ABS_MT_POSITION_Y , posy1); -input_mt_sync (tsdata->input); - -if (touch ==2 ) { -input_report_abs (tsdata->input, -ABS_MT_POSITION_X , posx2); -input_report_abs (tsdata->input, -ABS_MT_POSITION_Y , posy2); + touch = rdbuf[0 ]; +if (touch) { +u16 posx1 = (rdbuf[3 ] <<8 ) | rdbuf[2 ]; +u16 posy1 = (rdbuf[5 ] <<8 ) | rdbuf[4 ]; +u16 posx2 = (rdbuf[7 ] <<8 ) | rdbuf[6 ]; +u16 posy2 = (rdbuf[9 ] <<8 ) | rdbuf[8 ]; + +input_report_key (tsdata->input,BTN_TOUCH ,1 ); +input_report_abs (tsdata->input,ABS_X , posx1); +input_report_abs (tsdata->input,ABS_Y , posy1); + +input_report_abs (tsdata->input,ABS_MT_POSITION_X , + posx1); +input_report_abs (tsdata->input,ABS_MT_POSITION_Y , + posy1);input_mt_sync (tsdata->input); + +if (touch ==2 ) { +input_report_abs (tsdata->input, +ABS_MT_POSITION_X , posx2); +input_report_abs (tsdata->input, +ABS_MT_POSITION_Y , posy2); +input_mt_sync (tsdata->input); + } + }else { +input_report_key (tsdata->input,BTN_TOUCH ,0 ); } - }else { -input_report_key (tsdata->input,BTN_TOUCH ,0 ); - } -input_sync (tsdata->input); +input_sync (tsdata->input); + +if (gpio_get_value (pdata->gpio_attb)) +break ; + +msleep (20 ); + } } -static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) +static void pixcir_ts_typeb_report (struct pixcir_i2c_ts_data *ts) { -struct pixcir_i2c_ts_data *tsdata = dev_id; -const struct pixcir_ts_platform_data *pdata = tsdata->pdata; +const struct pixcir_ts_platform_data *pdata = ts->pdata; +struct device *dev = &ts->client->dev; +u8 rdbuf[32 ], wrbuf[1 ] = {0 }; +u8 *bufptr; +u8 num_fingers; +u8 unreliable; +int ret, i; + +while (!ts->exiting) { + + ret =i2c_master_send (ts->client, wrbuf,sizeof (wrbuf)); +if (ret !=sizeof (wrbuf)) { +dev_err (dev,"%s: i2c_master_send failed(), ret=%d\n" , + __func__, ret); +return ; + } -while (!tsdata->exiting) { -pixcir_ts_poscheck (tsdata); + ret =i2c_master_recv (ts->client, rdbuf,sizeof (rdbuf)); +if (ret !=sizeof (rdbuf)) { +dev_err (dev,"%s: i2c_master_recv failed(), ret=%d\n" , + __func__, ret); +return ; + } + + unreliable = rdbuf[0 ] &0xe0 ; + +if (unreliable) + goto next;/* ignore unreliable data */ + + num_fingers = rdbuf[0 ] &0x7 ; + bufptr = &rdbuf[2 ]; +if (num_fingers > ts->max_fingers) { + num_fingers = ts->max_fingers; +dev_dbg (dev,"limiting num_fingers to %d\n" , + num_fingers); + } + +for (i =0 ; i < num_fingers; i++) { +u8 id; +unsigned int x, y; +int slot; + + id = bufptr[4 ]; + slot =input_mt_get_slot_by_key (ts->input, id); +if (slot <0 ) { +dev_dbg (dev,"no free slot for id 0x%x\n" , id); +continue ; + } + + + x = bufptr[1 ] <<8 | bufptr[0 ]; + y = bufptr[3 ] <<8 | bufptr[2 ]; + +input_mt_slot (ts->input, slot); +input_mt_report_slot_state (ts->input, +MT_TOOL_FINGER , true); + +input_event (ts->input,EV_ABS ,ABS_MT_POSITION_X , x); +input_event (ts->input,EV_ABS ,ABS_MT_POSITION_Y , y); + + bufptr = &bufptr[5 ]; +dev_dbg (dev,"%d: id 0x%x slot %d, x %d, y %d\n" , + i, id, slot, x, y); + } + +/* One frame is complete so sync it */ +input_mt_sync_frame (ts->input); +input_sync (ts->input); + +next:if (gpio_get_value (pdata->gpio_attb))break ; -msleep (20 ); +usleep_range (2000 ,5000 ); } +} + +static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) +{ +struct pixcir_i2c_ts_data *tsdata = dev_id; + +if (tsdata->input->mt) +pixcir_ts_typeb_report (tsdata); +else +pixcir_ts_typea_report (tsdata);return IRQ_HANDLED ; }
@@ -376,9 +465,9 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, input->open = pixcir_input_open; input->close = pixcir_input_close; -__set_bit (EV_KEY , input->evbit);__set_bit (EV_ABS , input->evbit);__set_bit (BTN_TOUCH , input->keybit); +input_set_abs_params (input,ABS_X ,0 , pdata->x_size -1 ,0 ,0 ); input_set_abs_params(input, ABS_Y,
@@ -388,6 +477,25 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,input_set_abs_params (input,ABS_MT_POSITION_Y ,0 , pdata->y_size -1 ,0 ,0 ); +/* Type-B Multi-Touch support */ +if (pdata->chip.num_report_ids) { +const struct pixcir_i2c_chip_data *chip = &pdata->chip; + + tsdata->max_fingers = chip->num_report_ids; +if (tsdata->max_fingers >MAX_FINGERS ) { +dev_info (dev,"Limiting maximum fingers to %d\n" , +MAX_FINGERS ); + tsdata->max_fingers =MAX_FINGERS ; + } + + error =input_mt_init_slots (input, tsdata->max_fingers, +INPUT_MT_DIRECT |INPUT_MT_DROP_UNUSED ); +if (error) { +dev_err (dev,"Error initializing Multi-Touch slots\n" ); +return error; + } + } +input_set_drvdata (input, tsdata); error = devm_gpio_request_one(dev, pdata->gpio_attb,
Signature · 1 line
1.8.3.2
Dmitry Torokhov
maintainerRe: [PATCH 7/9] Input: pixcir_i2c_ts: Implement Type B Multi Touch reporting
Quoted 26 lines · Roger Quadros
Some pixcir controllers e.g. tangoC family report finger IDs with the co-ordinates and are more suitable for Type-B MT protocol.
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- drivers/input/touchscreen/pixcir_i2c_ts.c | 202 +++++++++++++++++++++++------- 1 file changed, 155 insertions(+), 47 deletions(-)drivers/input/touchscreen/pixcir_i2c_ts.c +3
-0@@ -23,84 +23,173 @@#include <linux/slab.h> #include <linux/i2c.h> #include <linux/input.h> +#include <linux/input/mt.h> #include <linux/input/pixcir_ts.h> #include <linux/gpio.h> #include <linux/of.h> #include <linux/of_gpio.h> #include <linux/of_device.h> +#define MAX_FINGERS 5/* Maximum supported by the driver */ +
drivers/input/touchscreen/pixcir_i2c_ts.c line 43
Quoted 10 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +2
-1struct pixcir_i2c_ts_data {struct i2c_client *client;struct input_dev *input;const struct pixcir_ts_platform_data *pdata;bool exiting; +u8 max_fingers;/* Maximum supported by the chip */ }; -static void pixcir_ts_poscheck (struct pixcir_i2c_ts_data *data) +static void pixcir_ts_typea_report (struct pixcir_i2c_ts_data *tsdata)
Hmm, I do not think we should keep Type A reports if we can do Type B. The protocols are not new and userspace should be able to handle MT-B by now.
Quoted 237 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +150
-46{ -struct pixcir_i2c_ts_data *tsdata = data; +const struct pixcir_ts_platform_data *pdata = tsdata->pdata;u8 rdbuf[10 ], wrbuf[1 ] = {0 };u8 touch;int ret; - ret =i2c_master_send (tsdata->client, wrbuf,sizeof (wrbuf)); -if (ret !=sizeof (wrbuf)) { -dev_err (&tsdata->client->dev, -"%s: i2c_master_send failed(), ret=%d\n" , - __func__, ret); -return ; - } +while (!tsdata->exiting) { - ret =i2c_master_recv (tsdata->client, rdbuf,sizeof (rdbuf)); -if (ret !=sizeof (rdbuf)) { -dev_err (&tsdata->client->dev, -"%s: i2c_master_recv failed(), ret=%d\n" , - __func__, ret); -return ; - } + ret =i2c_master_send (tsdata->client, wrbuf,sizeof (wrbuf)); +if (ret !=sizeof (wrbuf)) { +dev_err (&tsdata->client->dev, +"%s: i2c_master_send failed(), ret=%d\n" , + __func__, ret); +return ; + } + + ret =i2c_master_recv (tsdata->client, rdbuf,sizeof (rdbuf)); +if (ret !=sizeof (rdbuf)) { +dev_err (&tsdata->client->dev, +"%s: i2c_master_recv failed(), ret=%d\n" , + __func__, ret); +return ; + } - touch = rdbuf[0 ]; -if (touch) { -u16 posx1 = (rdbuf[3 ] <<8 ) | rdbuf[2 ]; -u16 posy1 = (rdbuf[5 ] <<8 ) | rdbuf[4 ]; -u16 posx2 = (rdbuf[7 ] <<8 ) | rdbuf[6 ]; -u16 posy2 = (rdbuf[9 ] <<8 ) | rdbuf[8 ]; - -input_report_key (tsdata->input,BTN_TOUCH ,1 ); -input_report_abs (tsdata->input,ABS_X , posx1); -input_report_abs (tsdata->input,ABS_Y , posy1); - -input_report_abs (tsdata->input,ABS_MT_POSITION_X , posx1); -input_report_abs (tsdata->input,ABS_MT_POSITION_Y , posy1); -input_mt_sync (tsdata->input); - -if (touch ==2 ) { -input_report_abs (tsdata->input, -ABS_MT_POSITION_X , posx2); -input_report_abs (tsdata->input, -ABS_MT_POSITION_Y , posy2); + touch = rdbuf[0 ]; +if (touch) { +u16 posx1 = (rdbuf[3 ] <<8 ) | rdbuf[2 ]; +u16 posy1 = (rdbuf[5 ] <<8 ) | rdbuf[4 ]; +u16 posx2 = (rdbuf[7 ] <<8 ) | rdbuf[6 ]; +u16 posy2 = (rdbuf[9 ] <<8 ) | rdbuf[8 ]; + +input_report_key (tsdata->input,BTN_TOUCH ,1 ); +input_report_abs (tsdata->input,ABS_X , posx1); +input_report_abs (tsdata->input,ABS_Y , posy1); + +input_report_abs (tsdata->input,ABS_MT_POSITION_X , + posx1); +input_report_abs (tsdata->input,ABS_MT_POSITION_Y , + posy1);input_mt_sync (tsdata->input); + +if (touch ==2 ) { +input_report_abs (tsdata->input, +ABS_MT_POSITION_X , posx2); +input_report_abs (tsdata->input, +ABS_MT_POSITION_Y , posy2); +input_mt_sync (tsdata->input); + } + }else { +input_report_key (tsdata->input,BTN_TOUCH ,0 ); } - }else { -input_report_key (tsdata->input,BTN_TOUCH ,0 ); - } -input_sync (tsdata->input); +input_sync (tsdata->input); + +if (gpio_get_value (pdata->gpio_attb)) +break ; + +msleep (20 ); + } } -static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) +static void pixcir_ts_typeb_report (struct pixcir_i2c_ts_data *ts) { -struct pixcir_i2c_ts_data *tsdata = dev_id; -const struct pixcir_ts_platform_data *pdata = tsdata->pdata; +const struct pixcir_ts_platform_data *pdata = ts->pdata; +struct device *dev = &ts->client->dev; +u8 rdbuf[32 ], wrbuf[1 ] = {0 }; +u8 *bufptr; +u8 num_fingers; +u8 unreliable; +int ret, i; + +while (!ts->exiting) { + + ret =i2c_master_send (ts->client, wrbuf,sizeof (wrbuf)); +if (ret !=sizeof (wrbuf)) { +dev_err (dev,"%s: i2c_master_send failed(), ret=%d\n" , + __func__, ret); +return ; + } -while (!tsdata->exiting) { -pixcir_ts_poscheck (tsdata); + ret =i2c_master_recv (ts->client, rdbuf,sizeof (rdbuf)); +if (ret !=sizeof (rdbuf)) { +dev_err (dev,"%s: i2c_master_recv failed(), ret=%d\n" , + __func__, ret); +return ; + } + + unreliable = rdbuf[0 ] &0xe0 ; + +if (unreliable) + goto next;/* ignore unreliable data */ + + num_fingers = rdbuf[0 ] &0x7 ; + bufptr = &rdbuf[2 ]; +if (num_fingers > ts->max_fingers) { + num_fingers = ts->max_fingers; +dev_dbg (dev,"limiting num_fingers to %d\n" , + num_fingers); + } + +for (i =0 ; i < num_fingers; i++) { +u8 id; +unsigned int x, y; +int slot; + + id = bufptr[4 ]; + slot =input_mt_get_slot_by_key (ts->input, id); +if (slot <0 ) { +dev_dbg (dev,"no free slot for id 0x%x\n" , id); +continue ; + } + + + x = bufptr[1 ] <<8 | bufptr[0 ]; + y = bufptr[3 ] <<8 | bufptr[2 ]; + +input_mt_slot (ts->input, slot); +input_mt_report_slot_state (ts->input, +MT_TOOL_FINGER , true); + +input_event (ts->input,EV_ABS ,ABS_MT_POSITION_X , x); +input_event (ts->input,EV_ABS ,ABS_MT_POSITION_Y , y); + + bufptr = &bufptr[5 ]; +dev_dbg (dev,"%d: id 0x%x slot %d, x %d, y %d\n" , + i, id, slot, x, y); + } + +/* One frame is complete so sync it */ +input_mt_sync_frame (ts->input); +input_sync (ts->input); + +next:if (gpio_get_value (pdata->gpio_attb))break ; -msleep (20 ); +usleep_range (2000 ,5000 ); } +} + +static irqreturn_t pixcir_ts_isr (int irq,void *dev_id) +{ +struct pixcir_i2c_ts_data *tsdata = dev_id; + +if (tsdata->input->mt) +pixcir_ts_typeb_report (tsdata); +else +pixcir_ts_typea_report (tsdata);return IRQ_HANDLED ; }@@ -376,9 +465,9 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client, input->open = pixcir_input_open; input->close = pixcir_input_close; -__set_bit (EV_KEY , input->evbit);__set_bit (EV_ABS , input->evbit);__set_bit (BTN_TOUCH , input->keybit); +input_set_abs_params (input,ABS_X ,0 , pdata->x_size -1 ,0 ,0 ); input_set_abs_params(input, ABS_Y,@@ -388,6 +477,25 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,input_set_abs_params (input,ABS_MT_POSITION_Y ,0 , pdata->y_size -1 ,0 ,0 ); +/* Type-B Multi-Touch support */ +if (pdata->chip.num_report_ids) { +const struct pixcir_i2c_chip_data *chip = &pdata->chip; + + tsdata->max_fingers = chip->num_report_ids; +if (tsdata->max_fingers >MAX_FINGERS ) { +dev_info (dev,"Limiting maximum fingers to %d\n" , +MAX_FINGERS ); + tsdata->max_fingers =MAX_FINGERS ; + } + + error =input_mt_init_slots (input, tsdata->max_fingers, +INPUT_MT_DIRECT |INPUT_MT_DROP_UNUSED ); +if (error) { +dev_err (dev,"Error initializing Multi-Touch slots\n" ); +return error; + } + } +input_set_drvdata (input, tsdata); error = devm_gpio_request_one(dev, pdata->gpio_attb,Signature · 1 line
1.8.3.2
Signature · 1 line
Dmitry
Re: [PATCH 7/9] Input: pixcir_i2c_ts: Implement Type B Multi Touch reporting
Hi Dmitry,
Quoted 35 lines · Dmitry Torokhov
Quoted 34 lines · Roger Quadros
Some pixcir controllers e.g. tangoC family report finger IDs with the co-ordinates and are more suitable for Type-B MT protocol.
Signed-off-by Roger Quadros <[email protected]>Acked-by Mugunthan V N <[email protected]>--- drivers/input/touchscreen/pixcir_i2c_ts.c | 202 +++++++++++++++++++++++------- 1 file changed, 155 insertions(+), 47 deletions(-)drivers/input/touchscreen/pixcir_i2c_ts.c +4
-0@@ -23,84 +23,173 @@#include <linux/slab.h> #include <linux/i2c.h> #include <linux/input.h> +#include <linux/input/mt.h> #include <linux/input/pixcir_ts.h> #include <linux/gpio.h> #include <linux/of.h> #include <linux/of_gpio.h> #include <linux/of_device.h> +#define MAX_FINGERS 5/* Maximum supported by the driver */ +struct pixcir_i2c_ts_data {struct i2c_client *client;struct input_dev *input;const struct pixcir_ts_platform_data *pdata;bool exiting; +u8 max_fingers;/* Maximum supported by the chip */ };
Quoted 7 lines
drivers/input/touchscreen/pixcir_i2c_ts.c line 43
Quoted 2 lines
drivers/input/touchscreen/pixcir_i2c_ts.c +1
-1-static void pixcir_ts_poscheck (struct pixcir_i2c_ts_data *data) +static void pixcir_ts_typea_report (struct pixcir_i2c_ts_data *tsdata)Hmm, I do not think we should keep Type A reports if we can do Type B. The protocols are not new and userspace should be able to handle MT-B by now.
It seems the controller the original driver was written for does not report touch ID and just reports 2 touch co-ordinates. I'm not sure how this fits into Type B reporting model.
cheers,
-roger
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 7/9] Input: pixcir_i2c_ts: Implement Type B Multi Touch reporting
Hi Roger,
Quoted 3 lines
It seems the controller the original driver was written for does not report touch ID and just reports 2 touch co-ordinates. I'm not sure how this fits into Type B reporting model.
Look in drivers/input/mouse/cypress_ps2.c for an example of how to deal with anonymous touch coordinates.
Thanks,
Henrik
PATCH 8/9 Input: pixcir_i2c_ts: Add support for TangoC family
In reply to Roger QuadrosAdd support for Pixcir TangoC controller.
--- .../devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt | 2 +- drivers/input/touchscreen/pixcir_i2c_ts.c | 6 ++++++ 2 files changed, 7 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +1 -1
@@ -1,7 +1,7 @@ * Pixcir I2C touchscreen controllers Required properties: -- compatible: must be "pixcir,pixcir_ts" +- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc" - reg: I2C address of the chip - interrupts: interrupt to which the chip is connected - attb-gpio: GPIO connected to the ATTB line of the chip
drivers/input/touchscreen/pixcir_i2c_ts.c +6 -0
@@ -549,13 +549,19 @@ static int pixcir_i2c_ts_remove(struct i2c_client *client)static const struct i2c_device_id pixcir_i2c_ts_id[] = { {"pixcir_ts" ,0 }, + {"pixcir_tangoc" ,0 }, { } };MODULE_DEVICE_TABLE (i2c, pixcir_i2c_ts_id);#if defined(CONFIG_OF ) +static const struct pixcir_i2c_chip_data tangoc_data = { + .num_report_ids =5 , +}; +static const struct of_device_id pixcir_of_match[] = { { .compatible ="pixcir,pixcir_ts" , }, + { .compatible ="pixcir,pixcir_tangoc" , .data = &tangoc_data, }, { } };MODULE_DEVICE_TABLE (of, pixcir_of_match);
Signature · 1 line
1.8.3.2
PATCH 9/9 Input: pixcir_i2c_ts: Implement wakeup from suspend
In reply to Roger QuadrosImprove the suspend and resume handlers to allow the device to wakeup the system from suspend.
--- drivers/input/touchscreen/pixcir_i2c_ts.c | 89 ++++++++++++++++++++++--------- 1 file changed, 63 insertions(+), 26 deletions(-)
drivers/input/touchscreen/pixcir_i2c_ts.c +63 -26
@@ -347,32 +347,6 @@ static void pixcir_input_close(struct input_dev *dev)return ; } - -#ifdef CONFIG_PM_SLEEP -static int pixcir_i2c_ts_suspend (struct device *dev) -{ -struct i2c_client *client =to_i2c_client (dev); - -if (device_may_wakeup (&client->dev)) -enable_irq_wake (client->irq); - -return 0 ; -} - -static int pixcir_i2c_ts_resume (struct device *dev) -{ -struct i2c_client *client =to_i2c_client (dev); - -if (device_may_wakeup (&client->dev)) -disable_irq_wake (client->irq); - -return 0 ; -} -#endif - -static SIMPLE_DEV_PM_OPS(pixcir_dev_pm_ops, - pixcir_i2c_ts_suspend, pixcir_i2c_ts_resume); -#if defined(CONFIG_OF )static const struct of_device_id pixcir_of_match[];
@@ -547,6 +521,69 @@ static int pixcir_i2c_ts_remove(struct i2c_client *client)return 0 ; } +#ifdef CONFIG_PM_SLEEP +static int pixcir_i2c_ts_suspend (struct device *dev) +{ +struct i2c_client *client =to_i2c_client (dev); +struct pixcir_i2c_ts_data *ts =i2c_get_clientdata (client); +struct input_dev *input = ts->input; +int ret =0 ; + +mutex_lock (&input->mutex); + +if (device_may_wakeup (&client->dev)) { +/* need to start device if not open, to be wakeup source */ +if (!input->users) { + ret =pixcir_start (ts); +if (ret) + goto unlock; + } + +enable_irq_wake (client->irq); + + }else if (input->users) { + ret =pixcir_stop (ts); + } + +unlock: +mutex_unlock (&input->mutex); + +return ret; +} + +static int pixcir_i2c_ts_resume (struct device *dev) +{ +struct i2c_client *client =to_i2c_client (dev); +struct pixcir_i2c_ts_data *ts =i2c_get_clientdata (client); +struct input_dev *input = ts->input; +int ret =0 ; + +mutex_lock (&input->mutex); + +if (device_may_wakeup (&client->dev)) { +disable_irq_wake (client->irq); + +/* need to stop device if it was not open on suspend */ +if (!input->users) { + ret =pixcir_stop (ts); +if (ret) + goto unlock; + } + + }else if (input->users) { + ret =pixcir_start (ts); + } + +unlock: +mutex_unlock (&input->mutex); + +return ret; +} +#endif + +static SIMPLE_DEV_PM_OPS(pixcir_dev_pm_ops, + pixcir_i2c_ts_suspend, pixcir_i2c_ts_resume); +static const struct i2c_device_id pixcir_i2c_ts_id[] = { {"pixcir_ts" ,0 }, {"pixcir_tangoc" ,0 },
Signature · 1 line
1.8.3.2