gpmi-nand bitflips in erased regions.
Subsystems (2)
PATCH v6 1/1 gpmi-nand bitflips in erased regions.
Changes in v6: Correction in obtaining the ecc_strength.
Elie De Brauwer (1):
mtd: gpmi: Deal with bitflips in erased regions regions
drivers/mtd/nand/gpmi-nand/bch-regs.h | 2 ++ drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 ++++++++++++++ drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 44 +++++++++++++++++++++++++++++++--- drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 1 + 4 files changed, 62 insertions(+), 3 deletions(-)
Signature · 1 line
1.8.5.1
PATCH v6 1/1 mtd: gpmi: Deal with bitflips in erased regions regions
The BCH block typically used with a GPMI block on an i.MX28/i.MX6 is only able to correct bitflips on data actually streamed through the block. When erasing a block the data does not stream through the BCH block and therefore no ECC data is written to the NAND chip. This causes gpmi_ecc_read_page to return failure as soon as a single non-1-bit is found in an erased page. Typically causing problems at higher levels (ubifs corrupted empty space warnings). This problem was also observed when using SLC NAND devices.
This patch configures the BCH block to mark a block as 'erased' if not too much bitflips are found. Next HW_BCH_STATUS0:ALLONES is used to check if the data read were all ones, indicating a read of a properly erased chunk was performed. If this was not the case a slow path is entered where bitflips are counted and corrected in software, allowing the upper layers to take proper actions.
--- drivers/mtd/nand/gpmi-nand/bch-regs.h | 2 ++ drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 ++++++++++++++ drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 44 +++++++++++++++++++++++++++++++--- drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 1 + 4 files changed, 62 insertions(+), 3 deletions(-)
drivers/mtd/nand/gpmi-nand/bch-regs.h +2 -0
@@ -30,7 +30,9 @@#define BM_BCH_CTRL_COMPLETE_IRQ (1 << 0)#define HW_BCH_STATUS0 0x00000010 +#define BM_BCH_STATUS0_ALLONES_MASK (1 << 4)#define HW_BCH_MODE 0x00000020 +#define BM_BCH_MODE_ERASE_THRESHOLD_MASK 0xff#define HW_BCH_ENCODEPTR 0x00000030#define HW_BCH_DATAPTR 0x00000040#define HW_BCH_METAPTR 0x00000050
drivers/mtd/nand/gpmi-nand/gpmi-lib.c +18 -0
@@ -244,6 +244,7 @@ int bch_set_geometry(struct gpmi_nand_data *this)unsigned int ecc_strength;unsigned int page_size;unsigned int gf_len; +unsigned int erase_threshold;int ret;if (common_nfc_set_geometry (this))
@@ -286,6 +287,14 @@ int bch_set_geometry(struct gpmi_nand_data *this) | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this), r->bch_regs + HW_BCH_FLASH0LAYOUT1); +/* Set the tolerance for bitflips when reading erased blocks. */ + erase_threshold = gf_len /2 ; +if (erase_threshold > bch_geo->ecc_strength) + erase_threshold = bch_geo->ecc_strength; + +writel (erase_threshold &BM_BCH_MODE_ERASE_THRESHOLD_MASK , + r->bch_regs +HW_BCH_MODE ); +/* Set *all* chip selects to use layout 0. */ writel (0 , r->bch_regs +HW_BCH_LAYOUTSELECT );
@@ -1094,6 +1103,15 @@ int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip)return reg & mask; } +/* Returns 1 if the last transaction consisted only out of ones. */ +int gpmi_all_ones (struct gpmi_nand_data *this) +{ +struct resources *r = &this->resources; +uint32_t reg =readl (r->bch_regs +HW_BCH_STATUS0 ); + +return reg &BM_BCH_STATUS0_ALLONES_MASK ; +} +static inline void set_dma_type (struct gpmi_nand_data *this,enum dma_ops_type type) {
drivers/mtd/nand/gpmi-nand/gpmi-nand.c +41 -3
68 lines not on this page · raw message
drivers/mtd/nand/gpmi-nand/gpmi-nand.h +1 -0
@@ -268,6 +268,7 @@ extern void gpmi_clear_bch(struct gpmi_nand_data *);extern void gpmi_dump_info (struct gpmi_nand_data *);extern int bch_set_geometry (struct gpmi_nand_data *);extern int gpmi_is_ready (struct gpmi_nand_data *,unsigned chip); +extern int gpmi_all_ones (struct gpmi_nand_data *);extern int gpmi_send_command (struct gpmi_nand_data *);extern void gpmi_begin (struct gpmi_nand_data *);extern void gpmi_end (struct gpmi_nand_data *);
Signature · 1 line
1.8.5.1
Re: [PATCH v6] mtd: gpmi: Deal with bitflips in erased regions regions
Quoted 16 lines · Elie De Brauwer
The BCH block typically used with a GPMI block on an i.MX28/i.MX6 is only able to correct bitflips on data actually streamed through the block. When erasing a block the data does not stream through the BCH block and therefore no ECC data is written to the NAND chip. This causes
gpmi_ecc_read_pageto return failure as soon as a single non-1-bit is found in an erased page. Typically causing problems at higher levels (ubifs corrupted empty space warnings). This problem was also observed when using SLC NAND devices.This patch configures the BCH block to mark a block as 'erased' if not too much bitflips are found. Next HW_BCH_STATUS0:ALLONES is used to check if the data read were all ones, indicating a read of a properly erased chunk was performed. If this was not the case a slow path is entered where bitflips are counted and corrected in software, allowing the upper layers to take proper actions.
Quoted 2 lines
Signed-off-by Elie De Brauwer <[email protected]>Acked-by Peter Korsgaard <[email protected]>
thanks a lot!
Re: [PATCH v6] mtd: gpmi: Deal with bitflips in erased regions regions
Quoted 17 lines · Huang Shijie
Quoted 16 lines · Elie De Brauwer
The BCH block typically used with a GPMI block on an i.MX28/i.MX6 is only able to correct bitflips on data actually streamed through the block. When erasing a block the data does not stream through the BCH block and therefore no ECC data is written to the NAND chip. This causes
gpmi_ecc_read_pageto return failure as soon as a single non-1-bit is found in an erased page. Typically causing problems at higher levels (ubifs corrupted empty space warnings). This problem was also observed when using SLC NAND devices.This patch configures the BCH block to mark a block as 'erased' if not too much bitflips are found. Next HW_BCH_STATUS0:ALLONES is used to check if the data read were all ones, indicating a read of a properly erased chunk was performed. If this was not the case a slow path is entered where bitflips are counted and corrected in software, allowing the upper layers to take proper actions.
Quoted 7 lines
Quoted 2 lines
Signed-off-by Elie De Brauwer <[email protected]>Acked-by Peter Korsgaard <[email protected]>thanks a lot!
Acked-by Huang Shijie <[email protected]>
Hello Huang, all,
Huang, you suggested earlier after checking with your hw guys to make use of the ALLONES bit
in the HW_BCH0_STATUS0 register, this looked like a nice solution since this could introduce a fast
path. However the documentation did not mention how the ALLONES bit is implemented, including whether
or not it takes the erase threshold into account. Obviously V6 of my patch will only function if ALLONES function if _all bits are physically one_ and fail to function if allones something like the AND of all statusses of the chunk.
I've been given a board with another bitflip (jay). It propgates as the following error:
"UBIFS error (pid 36): ubifs_recover_master_node: failed to recover master node"
And if I look at the data I see the LEB consists out of 55 valid master nodes, but two pages after the last valid master node there is a bitflip which causes in ubifs/recovery.c get_master_node() to trigger:
if (!is_empty(buf, len))
goto out_err;When dumping the data read I get to see a bitflip:
[ 4.094719] c8a32e30: ff ff ff fd ff ff ff ff ff ff ff ff ff ff ff
ff ................
This leads me to believe that the ALLONES bit is actually not behaving the way I think it was. Implying that it actually is taking the ERASE_THRESHOLD into account. (I verified this by dumping the status register which was 0xff10 and counting the bitflips which actually showed allones to be set while a bitflip was found) Making the allones bit more or less useless in our case. Hence I suggest to revert the use of the allones bit to the, (somewhat slower when reading erased blocks) solution which always checks the erased blocks in gpmi_ecc_read_page():
if (*status == STATUS_ERASED) {
/* Erased block with bitflips. */
flips = erased_sector_bitflips(payload_virt, i, nfc_geo);
} else {
/* BCH block corrected some errors for us. */ flips = *status;
}
What do you think and/or could you verify with your hardware guys ?
Thanks
E.
Signature · 1 line
Elie De Brauwer
Re: [PATCH v6] mtd: gpmi: Deal with bitflips in erased regions regions
Quoted 51 lines · Elie De Brauwer
Quoted 17 lines · Huang Shijie
Quoted 16 lines · Elie De Brauwer
The BCH block typically used with a GPMI block on an i.MX28/i.MX6 is only able to correct bitflips on data actually streamed through the block. When erasing a block the data does not stream through the BCH block and therefore no ECC data is written to the NAND chip. This causes
gpmi_ecc_read_pageto return failure as soon as a single non-1-bit is found in an erased page. Typically causing problems at higher levels (ubifs corrupted empty space warnings). This problem was also observed when using SLC NAND devices.This patch configures the BCH block to mark a block as 'erased' if not too much bitflips are found. Next HW_BCH_STATUS0:ALLONES is used to check if the data read were all ones, indicating a read of a properly erased chunk was performed. If this was not the case a slow path is entered where bitflips are counted and corrected in software, allowing the upper layers to take proper actions.
Quoted 7 lines
Quoted 2 lines
Signed-off-by Elie De Brauwer <[email protected]>Acked-by Peter Korsgaard <[email protected]>thanks a lot!
Acked-by Huang Shijie <[email protected]>Hello Huang, all,
Huang, you suggested earlier after checking with your hw guys to make use of the ALLONES bit
in theHW_BCH0_STATUS0register, this looked like a nice solution since this could introduce a fast
path. However the documentation did not mention how the ALLONES bit is implemented, including whether
or not it takes the erase threshold into account. Obviously V6 of my patch will only function if ALLONES function if_allbits are physicallyone_and fail to function if allones something like the AND of all statusses of the chunk.I've been given a board with another bitflip (jay). It propgates as the following error:
"UBIFS error (pid 36):ubifs_recover_master_node: failed to recover master node"And if I look at the data I see the LEB consists out of 55 valid master nodes, but two pages after the last valid master node there is a bitflip which causes in
ubifs/recovery.cget_master_node()to trigger:if (!is_empty(buf, len)) goto out_err;When dumping the data read I get to see a bitflip:
Quoted 8 lines
[ 4.094719] c8a32e30: ff ff ff fd ff ff ff ff ff ff ff ff ff ff ffff ................
This leads me to believe that the ALLONES bit is actually not behaving the way I think it was. Implying that it actually is taking the
ERASE_THRESHOLDinto account. (I verified this by dumping the status register which was0xff10and counting the bitflips which actually showed allones to be set while a bitflip was found) Making the allones
I confirmed with the hardware guy just now.
the hardware guy ate his word!
If we do not apply this patch, does it mean the UBIFS can not work?
thanks
Huang Shijie
Quoted 21 lines
bit more or less useless in our case. Hence I suggest to revert the use of the allones bit to the, (somewhat slower when reading erased blocks) solution which always checks the erased blocks in
gpmi_ecc_read_page():if (*status == STATUS_ERASED) { /* Erased block with bitflips. */ flips = erased_sector_bitflips(payload_virt, i, nfc_geo); } else {/* BCH block corrected some errors for us. */
flips = *status;
}What do you think and/or could you verify with your hardware guys ?
Thanks
E.Signature · 1 line
Elie De Brauwer
Re: [PATCH v6] mtd: gpmi: Deal with bitflips in erased regions regions
Quoted 61 lines · Huang Shijie
Quoted 51 lines · Elie De Brauwer
Quoted 17 lines · Huang Shijie
Quoted 16 lines · Elie De Brauwer
The BCH block typically used with a GPMI block on an i.MX28/i.MX6 is only able to correct bitflips on data actually streamed through the block. When erasing a block the data does not stream through the BCH block and therefore no ECC data is written to the NAND chip. This causes
gpmi_ecc_read_pageto return failure as soon as a single non-1-bit is found in an erased page. Typically causing problems at higher levels (ubifs corrupted empty space warnings). This problem was also observed when using SLC NAND devices.This patch configures the BCH block to mark a block as 'erased' if not too much bitflips are found. Next HW_BCH_STATUS0:ALLONES is used to check if the data read were all ones, indicating a read of a properly erased chunk was performed. If this was not the case a slow path is entered where bitflips are counted and corrected in software, allowing the upper layers to take proper actions.
Quoted 7 lines
Quoted 2 lines
Signed-off-by Elie De Brauwer <[email protected]>Acked-by Peter Korsgaard <[email protected]>thanks a lot!
Acked-by Huang Shijie <[email protected]>Hello Huang, all,
Huang, you suggested earlier after checking with your hw guys to make use of the ALLONES bit
in theHW_BCH0_STATUS0register, this looked like a nice solution since this could introduce a fast
path. However the documentation did not mention how the ALLONES bit is implemented, including whether
or not it takes the erase threshold into account. Obviously V6 of my patch will only function if ALLONES function if_allbits are physicallyone_and fail to function if allones something like the AND of all statusses of the chunk.I've been given a board with another bitflip (jay). It propgates as the following error:
"UBIFS error (pid 36):ubifs_recover_master_node: failed to recover master node"And if I look at the data I see the LEB consists out of 55 valid master nodes, but two pages after the last valid master node there is a bitflip which causes in
ubifs/recovery.cget_master_node()to trigger:if (!is_empty(buf, len)) goto out_err;When dumping the data read I get to see a bitflip:
Quoted 8 lines
[ 4.094719] c8a32e30: ff ff ff fd ff ff ff ff ff ff ff ff ff ff ffff ................
This leads me to believe that the ALLONES bit is actually not behaving the way I think it was. Implying that it actually is taking the
ERASE_THRESHOLDinto account. (I verified this by dumping the status register which was0xff10and counting the bitflips which actually showed allones to be set while a bitflip was found) Making the allones
Quoted 6 lines
I confirmed with the hardware guy just now.
the hardware guy ate his word!If we do not apply this patch, does it mean the UBIFS can not work?
Thanks for doublechecking ! I'll provide a new version of this patch in the weekend.
If this patch does not get applied you will get bugreports related to "corrupt empty space"
issues when using UBIFS, for the simple reason that ubifs only claims to be tolerant to
corruption due to powercuts, and ubifs relies on the mtd layer that bitflips are detected
and corrected. In my situation I have already seen two distinct units (on a 20 unit population
over a timespan of about two months) refuse to boot because of this issue, which were
both solved by this patch. So ubifs might seem to work, but people using it will likely bump
into nasty field issues.
my 2 cents
E.
Signature · 1 line
Elie De Brauwer
Re: [PATCH v6] mtd: gpmi: Deal with bitflips in erased regions regions
Quoted 11 lines · Elie De Brauwer
Quoted 7 lines
I confirmed with the hardware guy just now.
the hardware guy ate his word!If we do not apply this patch, does it mean the UBIFS can not work?
Thanks for doublechecking ! I'll provide a new version of this patch in the weekend.
Quoted 13 lines
If this patch does not get applied you will get bugreports related to "corrupt empty space"
issues when using UBIFS, for the simple reason that ubifs only claims to be tolerant to
corruption due to powercuts, and ubifs relies on the mtd layer that bitflips are detected
and corrected. In my situation I have already seen two distinct units (on a 20 unit population
over a timespan of about two months) refuse to boot because of this issue, which were
both solved by this patch. So ubifs might seem to work, but people using it will likely bump
into nasty field issues.
I will discuss with our manager next week, and i hope the hardware guy can fix it in the future.
thanks
Huang Shijie