ARM: dts: imx6qdl-sabresd: Add PFUZE100 support
Subsystems (3)
Fabio Estevam
reviewerPATCH v2 1/2 ARM: dts: imx6qdl-sabresd: Add PFUZE100 support
From: Fabio Estevam <[email protected]>
mx6 sabresd boards have Freescale PFUZE100 regulator, so add support for it.
Signed-off-by Robin Gong <[email protected]>
Signed-off-by Fabio Estevam <[email protected]>
---
Changes since v1:
- Fix the maximum voltage of sw2 regulator
arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 110 +++++++++++++++++++++++++++++++++ 1 file changed, 110 insertions(+)
arch/arm/boot/dts/imx6qdl-sabresd.dtsi +110 -0
@@ -165,6 +165,112 @@ }; }; +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic: pfuze100 at 08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + &i2c3 { clock-frequency = <100000>; pinctrl-names = "default";
@@ -223,6 +329,10 @@ fsl,pins = <MX6QDL_I2C1_PINGRP2>; }; + pinctrl_i2c2: i2c2grp { + fsl,pins = <MX6QDL_I2C2_PINGRP2>; + }; + pinctrl_i2c3: i2c3grp { fsl,pins = <MX6QDL_I2C3_PINGRP2>; };
Signature · 1 line
1.8.1.2
Fabio Estevam
reviewerPATCH v2 2/2 ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
From: Fabio Estevam <[email protected]>
PFUZE100 regulator is commonly found on mx6 based designs.
Add support for it.
Signed-off-by Fabio Estevam <[email protected]>
---
Changes since v1:
- None
arch/arm/configs/imx_v6_v7_defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm/configs/imx_v6_v7_defconfig +1 -0
@@ -167,6 +167,7 @@ CONFIG_REGULATOR_ANATOP=y CONFIG_REGULATOR_DA9052=y CONFIG_REGULATOR_MC13783=y CONFIG_REGULATOR_MC13892=y +CONFIG_REGULATOR_PFUZE100=y CONFIG_MEDIA_SUPPORT=y CONFIG_MEDIA_CAMERA_SUPPORT=y CONFIG_MEDIA_RC_SUPPORT=y
Signature · 1 line
1.8.1.2
Shawn Guo
AppliedPATCH v2 1/2 ARM: dts: imx6qdl-sabresd: Add PFUZE100 support
In reply to Fabio EstevamQuoted 6 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
mx6 sabresd boards have Freescale PFUZE100 regulator, so add support for it.
Signed-off-by Robin Gong <[email protected]>Signed-off-by Fabio Estevam <[email protected]>
Applied both, thanks.