Skip to contentSkip to conversation

powerpc/t104xrdb: Update T1042RDB.h in config folder

PATCH New Prabhakar Kushwaha 2 participants 2 messages Jan 27, 2014 – Feb 3, 2014

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 powerpc/t104xrdb: Update T1042RDB.h in config folder

-Add usb2 node entry in "hwconfig string"

-Remove controller interleaving from hwconfig string as T1040
has only one DDR conroller

-SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
are move outside so that they are defined for all cases as these macros are also used by other u-boot code

-Add CONFIG_SYS_CSPR2_EXT to make cpld accessible in u-boot

---
Changes for v2:

	correct usb1 string for ;
 include/configs/T1042RDB_PI.h |   15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)
include/configs/T1042RDB_PI.h +8 -7
index 104bb92..cd18de5 100644
@@ -80,10 +80,6 @@
 #if defined(CONFIG_SPIFLASH)
 #define CONFIG_SYS_EXTRA_ENV_RELOC
 #define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS              0
-#define CONFIG_ENV_SPI_CS               0
-#define CONFIG_ENV_SPI_MAX_HZ           10000000
-#define CONFIG_ENV_SPI_MODE             0
 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
 #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
 #define CONFIG_ENV_SECT_SIZE            0x10000
@@ -203,6 +199,7 @@
 /* CPLD on IFC */
 #define CONFIG_SYS_CPLD_BASE	0xffdf0000
 #define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2_EXT	(0xf)
 #define CONFIG_SYS_CSPR2	(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8 \
 				| CSPR_MSEL_GPCM \
@@ -395,6 +392,10 @@
 #define CONFIG_CMD_SF
 #define CONFIG_SF_DEFAULT_SPEED         10000000
 #define CONFIG_SF_DEFAULT_MODE          0
+#define CONFIG_ENV_SPI_BUS              0
+#define CONFIG_ENV_SPI_CS               0
+#define CONFIG_ENV_SPI_MAX_HZ           10000000
+#define CONFIG_ENV_SPI_MODE             0
 
 /*
  * General PCI
@@ -632,9 +633,9 @@
 #define __USB_PHY_TYPE	utmi
 
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
-	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
-	"bank_intlv=cs0_cs1;"					\
-	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+	"hwconfig=fsl_ddr:bank_intlv=cs0_cs1;"			\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) ";"\
+	"usb2:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 	"netdev=eth0\0"						\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
 	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH v2 1/1 powerpc/t104xrdb: Update T1042RDB.h in config folder

Quoted 11 lines · Prabhakar Kushwaha
(quoted diff) +0 -4
-Add usb2 node entry in "hwconfig string"
 
-Remove controller interleaving from hwconfig string as T1040
 has only one DDR conroller
 
-SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
 are move outside so that they are defined for all cases as these
 macros are also used by other u-boot code
 
-Add CONFIG_SYS_CSPR2_EXT to make cpld accessible in u-boot
Quoted 5 lines

---
Changes for v2:

	correct usb1 string for ;

Applied to u-boot-mpc85xx master branch.

York