In "pci_fixup_video" check if this is or should be the primary video device to prevent setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card
Hi Eiichiro / Dave / Greg,
While trying to get secondary PCI/VGA passthrough of a AMD 6570 card to a Xen guest with the radeon driver and modesetting i'm running into the problem that the driver says the BIOS is a COMBIOS while it expects a ATOMBIOS for the cards.
So the Guest uses both it's normal emulated VGA card provided by Qemu (f.e. cirrus logic) and a real VGA card via PCI passthrough.
While debugging it turned out that the bios that the driver read was not the AMD bios, but the bios from the emulated card. (so it wasn't a COMBIOS either ..)
I first thought the culprit was with Xen, Seabios or Qemu ..
So it took quite a while and debugging, but finally my eye fell on this in the guest dmesg:
[ 2.545728] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.545730] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.558998] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.559121] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.572412] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.572415] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.586527] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xd0 [ 2.586609] pci 0000:00:03.0: Boot video device [ 2.586696] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xd0 [ 2.586827] pci 0000:00:05.0: Boot video device [ 2.586928] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0
It's calling the "pci_fixup_video" quirk ... and it's calling it twice .. which if i read the comment correctly .. shouldn't be the case:
/*
* Fixup to mark boot BIOS video selected by BIOS before it changes *
* From information provided by "Jon Smirl" <[email protected]> *
* The standard boot ROM sequence for an x86 machine uses the BIOS
* to select an initial video card for boot display. This boot video
* card will have it's BIOS copied to C0000 in system RAM.
* IORESOURCE_ROM_SHADOW is used to associate the boot video
* card with this copy. On laptops this copy has to be used since
* the main ROM may be compressed or combined with another image.
* See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW
* is marked here since the boot video device will be the only enabled
* video device at this point.
*/
But the code doesn't check if it's actually the only enabled (or first) video device at that point .. and it's setting 2 boot video devices and setting both to use the IORESOURCE_ROM_SHADOW at C000 .. which happens to be the bios from the emulated card.
With this patch applied the passthrough of the card works fine in the guest and dmesg reports:
[ 2.167076] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.167078] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.179807] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.179953] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.192953] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.192955] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.206543] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xe0 [ 2.206623] pci 0000:00:03.0: Boot video device [ 2.206710] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xe0 [ 2.206842] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0
--
Sander
Sander Eikelenboom (1):
In "pci_fixup_video" check if this is or should be the primary video
device to prevent setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card
arch/x86/pci/fixup.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-)
Signature · 1 line
1.7.10.4
PATCH 1/1 In "pci_fixup_video" check if this is or should be the primary video device to prevent setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card
Setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card prevents if from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Fix this by checking if this is or should be the primary video device before applying the fix and let the comment reflect this.
--- arch/x86/pci/fixup.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-)
arch/x86/pci/fixup.c +9 -8
@@ -314,9 +314,9 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_r* IORESOURCE_ROM_SHADOW is used to associate the boot video * card with this copy. On laptops this copy has to be used since * the main ROM may be compressed or combined with another image. -* See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW -* is marked here since the boot video device will be the only enabled -* video device at this point. +* See pci_map_rom() for use of this flag. Before we mark the device +* with IORESOURCE_ROM_SHADOW we have to check if this is or should become +* the primary video card, since this quirk is ran for all video devices. */ static void pci_fixup_video (struct pci_dev *pdev)
@@ -347,12 +347,13 @@ static void pci_fixup_video(struct pci_dev *pdev) } bus = bus->parent; } -pci_read_config_word (pdev,PCI_COMMAND , &config); -if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { - pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; -dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" ); -if (!vga_default_device ()) +if (!vga_default_device () || pdev ==vga_default_device ()) { +pci_read_config_word (pdev,PCI_COMMAND , &config); +if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { + pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; +dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" );vga_set_default_device (pdev); + } } } DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
Signature · 1 line
1.7.10.4
A message that is not in the archive (sent off-list or not yet received): [email protected]
Re: In "pci_fixup_video" check if this is or should be the primary video device t
Quoted 8 lines · you
Hi Sander,
Quoted 2 lines
It's calling the "
pci_fixup_video" quirk ... and it's calling it twice .. which if i read the comment correctly .. shouldn't be the case:I think that there is only one bridge VGA Enable bit is set on normal machine. I guess two virtual VGA Enable bit are set on your virtual machine.
Quoted 8 lines
static void
pci_fixup_video(struct pci_dev *pdev)
...if (!(config & PCI_BRIDGE_CTL_VGA)) return; }...
Eiichiro
I have added some printk stuff .. and that shows that that code never runs for any of the 2 devices .. since it runs the while loop once but !bridge ...
Here is the complete lspci output, 00:03.0 is the emulated device, 00:05.0 the one passedthrough:
# lspci -vvknn
00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma] [8086:1237] (rev 02)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 000:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] [8086:7000]
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 IDE interface [0101]: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II] [8086:7010] (prog-if 80 [Master])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at c260 [size=16]
Kernel driver in use: PIIX_IDE
00:01.2 USB controller [0c03]: Intel Corporation 82371SB PIIX3 USB [Natoma/Triton II] [8086:7020] (rev 01) (prog-if 00 [UHCI])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at c240 [size=32]
Kernel driver in use: uhci_hcd
00:01.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 9
00:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device [5853:0001] (rev 01)
Subsystem: XenSource, Inc. Xen Platform Device [5853:0001]
Physical Slot: 2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 24
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at f2000000 (32-bit, prefetchable) [size=16M]
Kernel driver in use: xen-platform-pci
00:03.0 VGA compatible controller [0300]: Cirrus Logic GD 5446 [1013:00b8] (prog-if 00 [VGA controller])
Subsystem: Red Hat, Inc Device [1af4:1100]
Physical Slot: 3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=32M]
Region 1: Memory at f30b0000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at f30a0000 [disabled] [size=64K]00:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Turks [Radeon HD 6570] [1002:6759] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device [174b:e193]
Physical Slot: 5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 81
Region 0: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at f3060000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at c100 [size=256]
Expansion ROM at f3080000 [disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee57000 Data: 4300
Capabilities: [100 v9] #1002
Kernel driver in use: radeon
Quoted 78 lines
Quoted 78 lines
Hi Eiichiro / Dave / Greg,
While trying to get secondary PCI/VGA passthrough of a AMD 6570 card to a Xen guest with the radeon driver and modesetting i'm running into the problem that the driver says the BIOS is a COMBIOS while it expects a ATOMBIOS for the cards.
So the Guest uses both it's normal emulated VGA card provided by Qemu (f.e. cirrus logic) and a real VGA card via PCI passthrough.
While debugging it turned out that the bios that the driver read was not the AMD bios, but the bios from the emulated card. (so it wasn't a COMBIOS either ..)
I first thought the culprit was with Xen, Seabios or Qemu ..
So it took quite a while and debugging, but finally my eye fell on this in the guest dmesg:[ 2.545728] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.545730] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.558998] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.559121] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.572412] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.572415] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.586527] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xd0 [ 2.586609] pci 0000:00:03.0: Boot video device [ 2.586696] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xd0 [ 2.586827] pci 0000:00:05.0: Boot video device [ 2.586928] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0It's calling the "
pci_fixup_video" quirk ... and it's calling it twice .. which if i read the comment correctly .. shouldn't be the case:/*
* Fixup to mark boot BIOS video selected by BIOS before it changes *
* From information provided by "Jon Smirl" <[email protected]> *
* The standard boot ROM sequence for an x86 machine uses the BIOS
* to select an initial video card for boot display. This boot video
* card will have it's BIOS copied to C0000 in system RAM.
*IORESOURCE_ROM_SHADOWis used to associate the boot video
* card with this copy. On laptops this copy has to be used since
* the main ROM may be compressed or combined with another image.
* Seepci_map_rom()for use of this flag.IORESOURCE_ROM_SHADOW
* is marked here since the boot video device will be the only enabled
* video device at this point.
*/But the code doesn't check if it's actually the only enabled (or first) video device at that point .. and it's setting 2 boot video devices and setting both to use the
IORESOURCE_ROM_SHADOWat C000 .. which happens to be the bios from the emulated card.With this patch applied the passthrough of the card works fine in the guest and dmesg reports:
[ 2.167076] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.167078] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.179807] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.179953] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.192953] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.192955] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.206543] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xe0 [ 2.206623] pci 0000:00:03.0: Boot video device [ 2.206710] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xe0 [ 2.206842] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0--
SanderSander Eikelenboom (1):
In "pci_fixup_video" check if this is or should be the primary video
device to prevent setting theIORESOURCE_ROM_SHADOWflag on a secondary VGA card
arch/x86/pci/fixup.c| 17 +++++++++--------1 file changed, 9 insertions(+), 8 deletions(-)Signature · 1 line
1.7.10.4
A message that is not in the archive (sent off-list or not yet received): [email protected]
Re: In "pci_fixup_video" check if this is or should be the primary video devi
Wednesday, January 15, 2014, 5:55:38 AM, you wrote:
Ok, i will see what the Qemu guys have to say about it, the emulator is the latest Qemu, but they will probably say .. hey go fix that fixup in the kernel.
--
Sander
Quoted 221 lines
Hi Sander,
I understood there is no bridge for a VGA device in your virtual machine. Your emulator for the bridge control register is odd.
I guess your virtual machine ignore "PCI-to-PCI Bridge Architecture Specification".Thank you,
Eiichiro Oiwa
Quoted 210 lines
Quoted 8 lines · you
Hi Sander,
Quoted 2 lines
It's calling the "
pci_fixup_video" quirk ... and it's calling it twice .. which if i read the comment correctly .. shouldn't be the case:I think that there is only one bridge VGA Enable bit is set on normal machine. I guess two virtual VGA Enable bit are set on your virtual machine.
Quoted 8 lines
static void
pci_fixup_video(struct pci_dev *pdev)
...if (!(config & PCI_BRIDGE_CTL_VGA)) return; }...
Eiichiro
I have added some printk stuff .. and that shows that that code never runs for any of the 2 devices .. since it runs the while loop once but !bridge ...
Here is the complete lspci output, 00:03.0 is the emulated device, 00:05.0 the one passedthrough:
# lspci -vvknn 00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma] [8086:1237] (rev 02) Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100] Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 000:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] [8086:7000]
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 000:01.1 IDE interface [0101]: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II] [8086:7010] (prog-if 80 [Master])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at000001f0(32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at000003f0(type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at c260 [size=16]
Kernel driver in use:PIIX_IDE00:01.2 USB controller [0c03]: Intel Corporation 82371SB PIIX3 USB [Natoma/Triton II] [8086:7020] (rev 01) (prog-if 00 [UHCI])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at c240 [size=32]
Kernel driver in use:uhci_hcd00:01.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 900:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device [5853:0001] (rev 01)
Subsystem: XenSource, Inc. Xen Platform Device [5853:0001]
Physical Slot: 2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 24
Region 0: I/O ports at c000 [size=256]
Region 1: Memory atf2000000(32-bit, prefetchable) [size=16M]
Kernel driver in use: xen-platform-pci00:03.0 VGA compatible controller [0300]: Cirrus Logic GD 5446 [1013:00b8] (prog-if 00 [VGA controller])
Subsystem: Red Hat, Inc Device [1af4:1100] Physical Slot: 3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at f30b0000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at f30a0000 [disabled] [size=64K]00:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Turks [Radeon HD 6570] [1002:6759] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device [174b:e193]
Physical Slot: 5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 81
Region 0: Memory ate0000000(64-bit, prefetchable) [size=256M]
Region 2: Memory atf3060000(64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at c100 [size=256]
Expansion ROM atf3080000[disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address:00000000fee57000Data: 4300
Capabilities: [100 v9] #1002
Kernel driver in use: radeonQuoted 78 lines
Quoted 78 lines
Hi Eiichiro / Dave / Greg,
While trying to get secondary PCI/VGA passthrough of a AMD 6570 card to a Xen guest with the radeon driver and modesetting i'm running into the problem that the driver says the BIOS is a COMBIOS while it expects a ATOMBIOS for the cards.
So the Guest uses both it's normal emulated VGA card provided by Qemu (f.e. cirrus logic) and a real VGA card via PCI passthrough.
While debugging it turned out that the bios that the driver read was not the AMD bios, but the bios from the emulated card. (so it wasn't a COMBIOS either ..)
I first thought the culprit was with Xen, Seabios or Qemu ..
So it took quite a while and debugging, but finally my eye fell on this in the guest dmesg:[ 2.545728] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.545730] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.558998] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.559121] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.572412] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.572415] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.586527] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xd0 [ 2.586609] pci 0000:00:03.0: Boot video device [ 2.586696] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xd0 [ 2.586827] pci 0000:00:05.0: Boot video device [ 2.586928] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0It's calling the "
pci_fixup_video" quirk ... and it's calling it twice .. which if i read the comment correctly .. shouldn't be the case:/*
* Fixup to mark boot BIOS video selected by BIOS before it changes *
* From information provided by "Jon Smirl" <[email protected]> *
* The standard boot ROM sequence for an x86 machine uses the BIOS
* to select an initial video card for boot display. This boot video
* card will have it's BIOS copied to C0000 in system RAM.
*IORESOURCE_ROM_SHADOWis used to associate the boot video
* card with this copy. On laptops this copy has to be used since
* the main ROM may be compressed or combined with another image.
* Seepci_map_rom()for use of this flag.IORESOURCE_ROM_SHADOW
* is marked here since the boot video device will be the only enabled
* video device at this point.
*/But the code doesn't check if it's actually the only enabled (or first) video device at that point .. and it's setting 2 boot video devices and setting both to use the
IORESOURCE_ROM_SHADOWat C000 .. which happens to be the bios from the emulated card.With this patch applied the passthrough of the card works fine in the guest and dmesg reports:
[ 2.167076] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.167078] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.179807] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.179953] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.192953] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.192955] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.206543] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xe0 [ 2.206623] pci 0000:00:03.0: Boot video device [ 2.206710] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xe0 [ 2.206842] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0--
SanderSander Eikelenboom (1):
In "pci_fixup_video" check if this is or should be the primary video
device to prevent setting theIORESOURCE_ROM_SHADOWflag on a secondary VGA card
arch/x86/pci/fixup.c| 17 +++++++++--------1 file changed, 9 insertions(+), 8 deletions(-)Signature · 1 line
1.7.10.4
Re: In "pci_fixup_video" check if this is or should be the primary video devi
In reply to a message not in the archiveQuoted 6 lines · you
Hi Sander,
I understood there is no bridge for a VGA device in your virtual machine. Your emulator for the bridge control register is odd.
I guess your virtual machine ignore "PCI-to-PCI Bridge Architecture Specification".
All the devices are connected to the root bus and by reading from what i could find that would be a valid setup. (perhaps not common, but hey we are doing a fixup here for other non common cases).
And i don't understand what is wrong with my patch, earlier in the boot the vga_default_device is already set by the arch and/or vga arbitration code before the fixup is being run.
In other words ..
If we know the vga boot device .. why not use that information to apply the fixup *only* to that vga boot device ?
And that's just what my patch does ..
+ if (!vga_default_device() || pdev == vga_default_device()) {
If we don't know the vga_default_device ... because we don't have that knowlegde or
if this is actually the vga_default_device ... because we do have that knowledge ..
and only then .. run the fixup code and set this device as the vga_default_device
So this change actually makes the code adhere to the comment already above it .. saying it should only be applied to the vga_default_device aka boot video device.
Also added Bjorn and linux-pci to the CC .. should have done that right away .. sorry for that.
--
Sander
Quoted 214 lines
Thank you,
Eiichiro Oiwa
Quoted 210 lines
Quoted 8 lines · you
Hi Sander,
Quoted 2 lines
It's calling the "
pci_fixup_video" quirk ... and it's calling it twice .. which if i read the comment correctly .. shouldn't be the case:I think that there is only one bridge VGA Enable bit is set on normal machine. I guess two virtual VGA Enable bit are set on your virtual machine.
Quoted 8 lines
static void
pci_fixup_video(struct pci_dev *pdev)
...if (!(config & PCI_BRIDGE_CTL_VGA)) return; }...
Eiichiro
I have added some printk stuff .. and that shows that that code never runs for any of the 2 devices .. since it runs the while loop once but !bridge ...
Here is the complete lspci output, 00:03.0 is the emulated device, 00:05.0 the one passedthrough:
# lspci -vvknn 00:00.0 Host bridge [0600]: Intel Corporation 440FX - 82441FX PMC [Natoma] [8086:1237] (rev 02) Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100] Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 000:01.0 ISA bridge [0601]: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] [8086:7000]
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 000:01.1 IDE interface [0101]: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II] [8086:7010] (prog-if 80 [Master])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at000001f0(32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at000003f0(type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at c260 [size=16]
Kernel driver in use:PIIX_IDE00:01.2 USB controller [0c03]: Intel Corporation 82371SB PIIX3 USB [Natoma/Triton II] [8086:7020] (rev 01) (prog-if 00 [UHCI])
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at c240 [size=32]
Kernel driver in use:uhci_hcd00:01.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03)
Subsystem: Red Hat, Inc Qemu virtual machine [1af4:1100]
Physical Slot: 1
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 900:02.0 Unassigned class [ff80]: XenSource, Inc. Xen Platform Device [5853:0001] (rev 01)
Subsystem: XenSource, Inc. Xen Platform Device [5853:0001]
Physical Slot: 2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 24
Region 0: I/O ports at c000 [size=256]
Region 1: Memory atf2000000(32-bit, prefetchable) [size=16M]
Kernel driver in use: xen-platform-pci00:03.0 VGA compatible controller [0300]: Cirrus Logic GD 5446 [1013:00b8] (prog-if 00 [VGA controller])
Subsystem: Red Hat, Inc Device [1af4:1100] Physical Slot: 3 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at f0000000 (32-bit, prefetchable) [size=32M] Region 1: Memory at f30b0000 (32-bit, non-prefetchable) [size=4K] Expansion ROM at f30a0000 [disabled] [size=64K]00:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Turks [Radeon HD 6570] [1002:6759] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Device [174b:e193]
Physical Slot: 5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 81
Region 0: Memory ate0000000(64-bit, prefetchable) [size=256M]
Region 2: Memory atf3060000(64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at c100 [size=256]
Expansion ROM atf3080000[disabled] [size=128K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Legacy Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address:00000000fee57000Data: 4300
Capabilities: [100 v9] #1002
Kernel driver in use: radeonQuoted 78 lines
Quoted 78 lines
Hi Eiichiro / Dave / Greg,
While trying to get secondary PCI/VGA passthrough of a AMD 6570 card to a Xen guest with the radeon driver and modesetting i'm running into the problem that the driver says the BIOS is a COMBIOS while it expects a ATOMBIOS for the cards.
So the Guest uses both it's normal emulated VGA card provided by Qemu (f.e. cirrus logic) and a real VGA card via PCI passthrough.
While debugging it turned out that the bios that the driver read was not the AMD bios, but the bios from the emulated card. (so it wasn't a COMBIOS either ..)
I first thought the culprit was with Xen, Seabios or Qemu ..
So it took quite a while and debugging, but finally my eye fell on this in the guest dmesg:[ 2.545728] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.545730] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.558998] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.559121] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.572412] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.572415] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.586527] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xd0 [ 2.586609] pci 0000:00:03.0: Boot video device [ 2.586696] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xd0 [ 2.586827] pci 0000:00:05.0: Boot video device [ 2.586928] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0It's calling the "
pci_fixup_video" quirk ... and it's calling it twice .. which if i read the comment correctly .. shouldn't be the case:/*
* Fixup to mark boot BIOS video selected by BIOS before it changes *
* From information provided by "Jon Smirl" <[email protected]> *
* The standard boot ROM sequence for an x86 machine uses the BIOS
* to select an initial video card for boot display. This boot video
* card will have it's BIOS copied to C0000 in system RAM.
*IORESOURCE_ROM_SHADOWis used to associate the boot video
* card with this copy. On laptops this copy has to be used since
* the main ROM may be compressed or combined with another image.
* Seepci_map_rom()for use of this flag.IORESOURCE_ROM_SHADOW
* is marked here since the boot video device will be the only enabled
* video device at this point.
*/But the code doesn't check if it's actually the only enabled (or first) video device at that point .. and it's setting 2 boot video devices and setting both to use the
IORESOURCE_ROM_SHADOWat C000 .. which happens to be the bios from the emulated card.With this patch applied the passthrough of the card works fine in the guest and dmesg reports:
[ 2.167076] pci 0000:00:00.0: calling quirk_natoma+0x0/0x40 [ 2.167078] pci 0000:00:00.0: Limiting direct PCI/PCI transfers [ 2.179807] pci 0000:00:00.0: calling quirk_passive_release+0x0/0x90 [ 2.179953] pci 0000:00:01.0: PIIX3: Enabling Passive Release [ 2.192953] pci 0000:00:01.0: calling quirk_isa_dma_hangs+0x0/0x40 [ 2.192955] pci 0000:00:01.0: Activating ISA DMA hang workarounds [ 2.206543] pci 0000:00:03.0: calling pci_fixup_video+0x0/0xe0 [ 2.206623] pci 0000:00:03.0: Boot video device [ 2.206710] pci 0000:00:05.0: calling pci_fixup_video+0x0/0xe0 [ 2.206842] pci 0000:00:06.0: calling quirk_e100_interrupt+0x0/0x1c0--
SanderSander Eikelenboom (1):
In "pci_fixup_video" check if this is or should be the primary video
device to prevent setting theIORESOURCE_ROM_SHADOWflag on a secondary VGA card
arch/x86/pci/fixup.c| 17 +++++++++--------1 file changed, 9 insertions(+), 8 deletions(-)Signature · 1 line
1.7.10.4
Bjorn Helgaas
maintainerRe: In "pci_fixup_video" check if this is or should be the primary video devi
Quoted 9 lines · Sander Eikelenboom
...
And that's just what my patch does ..+ if (!vga_default_device() || pdev ==
vga_default_device()) {If we don't know the
vga_default_device... because we don't have that knowlegde or
if this is actually thevga_default_device... because we do have that knowledge ..
Quoted 8 lines
and only then .. run the fixup code and set this device as the
vga_default_deviceSo this change actually makes the code adhere to the comment already above it .. saying it should only be applied to the
vga_default_deviceaka boot video device.Also added Bjorn and linux-pci to the CC .. should have done that right away .. sorry for that.
Can you resend your patch to linux-pci? I don't think it made it there.
Bjorn
Re: In "pci_fixup_video" check if this is or should be the primary video devi
Quoted 17 lines · you
Quoted 15 lines · Sander Eikelenboom
...
And that's just what my patch does ..+ if (!vga_default_device() || pdev ==
vga_default_device()) {If we don't know the
vga_default_device... because we don't have that knowlegde or
if this is actually thevga_default_device... because we do have that knowledge ..and only then .. run the fixup code and set this device as the
vga_default_deviceSo this change actually makes the code adhere to the comment already above it .. saying it should only be applied to the
vga_default_deviceaka boot video device.
Quoted 6 lines
Quoted 2 lines
Also added Bjorn and linux-pci to the CC .. should have done that right away .. sorry for that.
Can you resend your patch to linux-pci? I don't think it made it there.
Bjorn
Sure .. also attached for the case it gets mangled ..
Date: Sun, 12 Jan 2014 04:49:44 +0100
Subject: [PATCH] In "pci_fixup_video" check if this is or should be the
primary video device to prevent setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card
To: Dave Airlie <[email protected]>,
Eiichiro Oiwa <[email protected]>,
Greg Kroah-Hartman <[email protected]>
Cc: Konrad Rzeszutek Wilk <[email protected]>,
[email protected] <[email protected]>
Setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card prevents if from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Fix this by checking if this is or should be the primary video device before applying the fix and let the comment reflect this.
--- arch/x86/pci/fixup.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-)
arch/x86/pci/fixup.c +9 -8
@@ -314,9 +314,9 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_r* IORESOURCE_ROM_SHADOW is used to associate the boot video * card with this copy. On laptops this copy has to be used since * the main ROM may be compressed or combined with another image. -* See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW -* is marked here since the boot video device will be the only enabled -* video device at this point. +* See pci_map_rom() for use of this flag. Before we mark the device +* with IORESOURCE_ROM_SHADOW we have to check if this is or should become +* the primary video card, since this quirk is ran for all video devices. */ static void pci_fixup_video (struct pci_dev *pdev)
@@ -347,12 +347,13 @@ static void pci_fixup_video(struct pci_dev *pdev) } bus = bus->parent; } -pci_read_config_word (pdev,PCI_COMMAND , &config); -if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { - pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; -dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" ); -if (!vga_default_device ()) +if (!vga_default_device () || pdev ==vga_default_device ()) { +pci_read_config_word (pdev,PCI_COMMAND , &config); +if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { + pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; +dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" );vga_set_default_device (pdev); + } } } DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
Signature · 1 line
1.7.10.4
From 59b2928fbdf1197f874f9ee06a42ccd63daf1340 Mon Sep 17 00:00:00 2001
From: Sander Eikelenboom <[email protected]>
Date: Sun, 12 Jan 2014 04:49:44 +0100
Subject: [PATCH] In "pci_fixup_video" check if this is or should be the
primary video device to prevent setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card
To: Dave Airlie <[email protected]>,
Eiichiro Oiwa <[email protected]>,
Greg Kroah-Hartman <[email protected]>
Cc: Konrad Rzeszutek Wilk <[email protected]>,
[email protected] <[email protected]>
Setting the IORESOURCE_ROM_SHADOW flag on a secondary VGA card prevents if from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Fix this by checking if this is or should be the primary video device before applying the fix and let the comment reflect this.
--- arch/x86/pci/fixup.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-)
arch/x86/pci/fixup.c +9 -8
@@ -314,9 +314,9 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_r* IORESOURCE_ROM_SHADOW is used to associate the boot video * card with this copy. On laptops this copy has to be used since * the main ROM may be compressed or combined with another image. -* See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW -* is marked here since the boot video device will be the only enabled -* video device at this point. +* See pci_map_rom() for use of this flag. Before we mark the device +* with IORESOURCE_ROM_SHADOW we have to check if this is or should become +* the primary video card, since this quirk is ran for all video devices. */ static void pci_fixup_video (struct pci_dev *pdev)
@@ -347,12 +347,13 @@ static void pci_fixup_video(struct pci_dev *pdev) } bus = bus->parent; } -pci_read_config_word (pdev,PCI_COMMAND , &config); -if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { - pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; -dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" ); -if (!vga_default_device ()) +if (!vga_default_device () || pdev ==vga_default_device ()) { +pci_read_config_word (pdev,PCI_COMMAND , &config); +if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { + pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; +dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" );vga_set_default_device (pdev); + } } } DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
Signature · 1 line
1.7.10.4
A message that is not in the archive (sent off-list or not yet received): [email protected]
Bjorn Helgaas
maintainerRe: In "pci_fixup_video" check if this is or should be the primary video d
[+cc Michael, Jesse, David, qemu-devel]
Quoted 5 lines · On Wed, Jan 15, 2014 at 8:58 PM, <[email protected]> wrote:
I suggest you should not break the PCI specification, as a developer of proprietary hypervisor, but I think your patch is no problem.
Your PCI structure is specialized structure for your virtual machine. Maybe, your virtual machine will be causing another problem on Linux or other kernels because of breaking the PCI specification.
I assume you think qemu is breaking the PCI spec. What exactly do you think is broken? Please give specific references to the spec. This conversation is pretty fragmented, and I came in late, so I apologize if I missed this.
Bjorn
Bjorn Helgaas
maintainerRe: In "pci_fixup_video" check if this is or should be the primary video devi
In reply to Sander EikelenboomQuoted 46 lines · Sander Eikelenboom
Date: Sun, 12 Jan 2014 04:49:44 +0100
Subject: [PATCH] In "pci_fixup_video" check if this is or should be the
primary video device to prevent setting theIORESOURCE_ROM_SHADOWflag on a secondary VGA card
To: Dave Airlie <[email protected]>,
Eiichiro Oiwa <[email protected]>,
Greg Kroah-Hartman <[email protected]>
Cc: Konrad Rzeszutek Wilk <[email protected]>,
[email protected] <[email protected]>Setting the
IORESOURCE_ROM_SHADOWflag on a secondary VGA card prevents if from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.Fix this by checking if this is or should be the primary video device before applying the fix and let the comment reflect this.
Signed-off-by Sander Eikelenboom <[email protected]>--- arch/x86/pci/fixup.c | 17 +++++++++-------- 1 file changed, 9 insertions(+), 8 deletions(-)arch/x86/pci/fixup.c +3
-5@@ -314,9 +314,9 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_r* IORESOURCE_ROM_SHADOW is used to associate the boot video * card with this copy. On laptops this copy has to be used since * the main ROM may be compressed or combined with another image. -* See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW -* is marked here since the boot video device will be the only enabled -* video device at this point. +* See pci_map_rom() for use of this flag. Before we mark the device +* with IORESOURCE_ROM_SHADOW we have to check if this is or should become +* the primary video card, since this quirk is ran for all video devices. */ static void pci_fixup_video (struct pci_dev *pdev)@@ -347,12 +347,13 @@ static void pci_fixup_video(struct pci_dev *pdev) } bus = bus->parent; } -pci_read_config_word (pdev,PCI_COMMAND , &config); -if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) {
arch/x86/pci/fixup.c static void pci_fixup_video(struct pci_dev *pdev) · line 356
Quoted 10 lines
arch/x86/pci/fixup.c +6
-3- pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; -dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" ); -if (!vga_default_device ()) +if (!vga_default_device () || pdev ==vga_default_device ()) { +pci_read_config_word (pdev,PCI_COMMAND , &config); +if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { + pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; +dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" );vga_set_default_device (pdev); + }
ia64 also has a pci_fixup_video() that is essentially the same. Can you fix that one as well, unless there is a reason why the fix applies only to x86 and not to ia64?
Quoted 5 lines
arch/x86/pci/fixup.c +0
-0} } DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,Signature · 1 line
1.7.10.4
PATCH v2 1/1 Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Hi Bjorn / Tony,
I fixed up ia64 as well and brought it inline again with the x86 code, but i don't have a ia64 machine, so that part is untested. Perhaps Tony is able to review/test it ?
Sander
Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Fix this by checking if the arch code or vga-arbitration has already determined the vga_default_device, if so only apply the fix to this primary video device and let the comment reflect this.
v2:
- Fix pci_fixup_video both in x86 and ia64
Sander Eikelenboom (1):
Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the
primary prevents it from reading it's own rom. It will get the
content of the shadowrom at C000 instead, which is of the
primary VGA card and the driver of the secondary card will bail
out.
arch/ia64/pci/fixup.c | 24 +++++++++++++----------- arch/x86/pci/fixup.c | 18 ++++++++++-------- 2 files changed, 23 insertions(+), 19 deletions(-)
Signature · 1 line
1.7.10.4
PATCH v2 1/1 Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Fix this by checking if the arch code or vga-arbitration has already determined the vga_default_device, if so only apply the fix to this primary video device and let the comment reflect this.
--- arch/ia64/pci/fixup.c | 24 +++++++++++++----------- arch/x86/pci/fixup.c | 18 ++++++++++-------- 2 files changed, 23 insertions(+), 19 deletions(-)
arch/ia64/pci/fixup.c +13 -11
@@ -19,9 +19,10 @@* IORESOURCE_ROM_SHADOW is used to associate the boot video * card with this copy. On laptops this copy has to be used since * the main ROM may be compressed or combined with another image. -* See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW -* is marked here since the boot video device will be the only enabled -* video device at this point. +* See pci_map_rom() for use of this flag. Before marking the device +* with IORESOURCE_ROM_SHADOW check if a vga_default_device is already set +* by either arch cde or vga-arbitration, if so only apply the fixup to this +* already determined primary video card. */ static void pci_fixup_video (struct pci_dev *pdev)
@@ -35,9 +36,6 @@ static void pci_fixup_video(struct pci_dev *pdev)return ;/* Maybe, this machine supports legacy memory map. */ -if ((pdev->class >>8 ) !=PCI_CLASS_DISPLAY_VGA ) -return ; -/* Is VGA routed to us? */ bus = pdev->bus;while (bus) {
@@ -60,10 +58,14 @@ static void pci_fixup_video(struct pci_dev *pdev) } bus = bus->parent; } -pci_read_config_word (pdev,PCI_COMMAND , &config); -if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { - pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; -dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" ); +if (!vga_default_device () || pdev =vga_default_device ()) { +pci_read_config_word (pdev,PCI_COMMAND , &config); +if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { + pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; +dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" ); +vga_set_default_device (pdev); + } } } -DECLARE_PCI_FIXUP_HEADER (PCI_ANY_ID ,PCI_ANY_ID , pci_fixup_video); +DECLARE_PCI_FIXUP_CLASS_FINAL (PCI_ANY_ID ,PCI_ANY_ID , +PCI_CLASS_DISPLAY_VGA ,8 , pci_fixup_video);
arch/x86/pci/fixup.c +10 -8
@@ -314,9 +314,10 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_r* IORESOURCE_ROM_SHADOW is used to associate the boot video * card with this copy. On laptops this copy has to be used since * the main ROM may be compressed or combined with another image. -* See pci_map_rom() for use of this flag. IORESOURCE_ROM_SHADOW -* is marked here since the boot video device will be the only enabled -* video device at this point. +* See pci_map_rom() for use of this flag. Before marking the device +* with IORESOURCE_ROM_SHADOW check if a vga_default_device is already set +* by either arch cde or vga-arbitration, if so only apply the fixup to this +* already determined primary video card. */ static void pci_fixup_video (struct pci_dev *pdev)
@@ -347,12 +348,13 @@ static void pci_fixup_video(struct pci_dev *pdev) } bus = bus->parent; } -pci_read_config_word (pdev,PCI_COMMAND , &config); -if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { - pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; -dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" ); -if (!vga_default_device ()) +if (!vga_default_device () || pdev =vga_default_device ()) { +pci_read_config_word (pdev,PCI_COMMAND , &config); +if (config & (PCI_COMMAND_IO |PCI_COMMAND_MEMORY )) { + pdev->resource[PCI_ROM_RESOURCE ].flags |=IORESOURCE_ROM_SHADOW ; +dev_printk (KERN_DEBUG , &pdev->dev,"Boot video device\n" );vga_set_default_device (pdev); + } } } DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
Signature · 1 line
1.7.10.4
Re: [PATCH v2] Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
In reply to Sander EikelenboomQuoted 23 lines · Sander Eikelenboom
Hi Bjorn / Tony,
I fixed up ia64 as well and brought it inline again with the x86 code, but i don't have a ia64 machine, so that part is untested. Perhaps Tony is able to review/test it ?
Sander
Setting the
IORESOURCE_ROM_SHADOWflag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.Fix this by checking if the arch code or vga-arbitration has already determined the
vga_default_device, if so only apply the fix to this primary video device and let the comment reflect this.v2:
- Fixpci_fixup_videoboth in x86 and ia64
Quoted 6 lines
Sander Eikelenboom (1):
Setting theIORESOURCE_ROM_SHADOWflag on a VGA card other than the
primary prevents it from reading it's own rom. It will get the
content of the shadowrom at C000 instead, which is of the
primary VGA card and the driver of the secondary card will bail
out.
Your editor mutilated your subject line. It ought to have been just one line.
Anyhow, you can also add 'Reviewed-by: Konrad Rzeszutek Wilk <[email protected]' on the patch for the x86 part.
The ia64 "looks" OK to me, but my ia64 box won't boot v3.11 or later so I can't give it a 'Tested-by' yet.
Quoted 8 lines
arch/ia64/pci/fixup.c | 24 +++++++++++++----------- arch/x86/pci/fixup.c | 18 ++++++++++-------- 2 files changed, 23 insertions(+), 19 deletions(-)Signature · 1 line
1.7.10.4
Re: [PATCH v2] Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Hi All,
Still trying to collect tested and acked-by's ..
Dave,
In commit 6cf20beec4b91c240cf759b4db72669e251f1fc4 you changed pci_fixup_video saying:
"This fixes the switcheroo on my T410s."
Do you still have the machine and could you verify if it still works with this patch applied ?
Eiichiro,
Most of last major overhaul of pci_fixup_video was in commit 6b5c76b8e2ff204fa8d7201acce461188873bf2b saying:
"PCI: fix pci_fixup_video as it blows up on sparc64"
Is it possible for you to verify you can still boot on sparc64 with this patch applied ?
Tony,
Since ia64's pci_fixup_video is also changed to be inline with x86, could you verify it still compiles and boots for you ?
Konrad,
Thanks for reviewing and testing !
--
Sander
Quoted 48 lines · you
Quoted 23 lines · Sander Eikelenboom
Hi Bjorn / Tony,
I fixed up ia64 as well and brought it inline again with the x86 code, but i don't have a ia64 machine, so that part is untested. Perhaps Tony is able to review/test it ?
Sander
Setting the
IORESOURCE_ROM_SHADOWflag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.Fix this by checking if the arch code or vga-arbitration has already determined the
vga_default_device, if so only apply the fix to this primary video device and let the comment reflect this.v2:
- Fixpci_fixup_videoboth in x86 and ia64Quoted 6 lines
Sander Eikelenboom (1):
Setting theIORESOURCE_ROM_SHADOWflag on a VGA card other than the
primary prevents it from reading it's own rom. It will get the
content of the shadowrom at C000 instead, which is of the
primary VGA card and the driver of the secondary card will bail
out.Your editor mutilated your subject line. It ought to have been just one line.
Anyhow, you can also add 'Reviewed-by: Konrad Rzeszutek Wilk <[email protected]' on the patch for the x86 part.
The ia64 "looks" OK to me, but my ia64 box won't boot v3.11 or later so I can't give it a 'Tested-by' yet.
Quoted 8 lines
arch/ia64/pci/fixup.c | 24 +++++++++++++----------- arch/x86/pci/fixup.c | 18 ++++++++++-------- 2 files changed, 23 insertions(+), 19 deletions(-)Signature · 1 line
1.7.10.4
Re: [PATCH v2] Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
In reply to Konrad Rzeszutek WilkHi Bjorn,
I have given it another email and another week, but without gaining any reviewed or acked-by's. It seems the only way forward is to shovel it in linux-next earlier, give it a good soak and see if anyone starts to squeal .. or that everything seems to be ok :-)
Would you need a v3 with the acked and reviewed-by from Konrad for x86 in it ?
--
Sander
Quoted 48 lines · you
Quoted 23 lines · Sander Eikelenboom
Hi Bjorn / Tony,
I fixed up ia64 as well and brought it inline again with the x86 code, but i don't have a ia64 machine, so that part is untested. Perhaps Tony is able to review/test it ?
Sander
Setting the
IORESOURCE_ROM_SHADOWflag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.Fix this by checking if the arch code or vga-arbitration has already determined the
vga_default_device, if so only apply the fix to this primary video device and let the comment reflect this.v2:
- Fixpci_fixup_videoboth in x86 and ia64Quoted 6 lines
Sander Eikelenboom (1):
Setting theIORESOURCE_ROM_SHADOWflag on a VGA card other than the
primary prevents it from reading it's own rom. It will get the
content of the shadowrom at C000 instead, which is of the
primary VGA card and the driver of the secondary card will bail
out.Your editor mutilated your subject line. It ought to have been just one line.
Anyhow, you can also add 'Reviewed-by: Konrad Rzeszutek Wilk <[email protected]' on the patch for the x86 part.
The ia64 "looks" OK to me, but my ia64 box won't boot v3.11 or later so I can't give it a 'Tested-by' yet.
Quoted 8 lines
arch/ia64/pci/fixup.c | 24 +++++++++++++----------- arch/x86/pci/fixup.c | 18 ++++++++++-------- 2 files changed, 23 insertions(+), 19 deletions(-)Signature · 1 line
1.7.10.4
Bjorn Helgaas
maintainerRe: [PATCH v2] Setting the IORESOURCE_ROM_SHADOW flag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.
Quoted 7 lines · Sander Eikelenboom
Hi Bjorn,
I have given it another email and another week, but without gaining any reviewed or acked-by's. It seems the only way forward is to shovel it in linux-next earlier, give it a good soak and see if anyone starts to squeal .. or that everything seems to be ok :-)
Would you need a v3 with the acked and reviewed-by from Konrad for x86 in it ?
No need, I applied this to my pci/misc branch for v3.15.
Tony, let me know if you have any issues with this.
Bjorn
Quoted 52 lines
Quoted 48 lines · you
Quoted 23 lines · Sander Eikelenboom
Hi Bjorn / Tony,
I fixed up ia64 as well and brought it inline again with the x86 code, but i don't have a ia64 machine, so that part is untested. Perhaps Tony is able to review/test it ?
Sander
Setting the
IORESOURCE_ROM_SHADOWflag on a VGA card other than the primary prevents it from reading it's own rom. It will get the content of the shadowrom at C000 instead, which is of the primary VGA card and the driver of the secondary card will bail out.Fix this by checking if the arch code or vga-arbitration has already determined the
vga_default_device, if so only apply the fix to this primary video device and let the comment reflect this.v2:
- Fixpci_fixup_videoboth in x86 and ia64Quoted 6 lines
Sander Eikelenboom (1):
Setting theIORESOURCE_ROM_SHADOWflag on a VGA card other than the
primary prevents it from reading it's own rom. It will get the
content of the shadowrom at C000 instead, which is of the
primary VGA card and the driver of the secondary card will bail
out.Your editor mutilated your subject line. It ought to have been just one line.
Anyhow, you can also add 'Reviewed-by: Konrad Rzeszutek Wilk <[email protected]' on the patch for the x86 part.
The ia64 "looks" OK to me, but my ia64 box won't boot v3.11 or later so I can't give it a 'Tested-by' yet.
Quoted 8 lines
arch/ia64/pci/fixup.c | 24 +++++++++++++----------- arch/x86/pci/fixup.c | 18 ++++++++++-------- 2 files changed, 23 insertions(+), 19 deletions(-)Signature · 1 line
1.7.10.4