OpenCores 10/100 MAC fixes for gigabit environment
Subsystems (2)
v3 cover OpenCores 10/100 MAC fixes for gigabit environment
Hello David, Ben, Florian, Chris and everybody,
this series improves ethoc behavior in gigabit environment:
- first patch disables gigabit advertisement in the attached PHY making possible to use gigabit link without any additional setup;
- second patch adds support to set up MII management bus frequency, adding new fields to platform data and to OF bindings.
These changes allow to use KC-705 board with 50MHz xtensa core and OpenCores 10/100 Mbps MAC connected to gigabit network without any additional setup.
Changes v2->v3:
- drop accessors for 'advertising' and 'supported' fields;
- don't call phy_start_aneg to force phylib to disable gigabit advertisement;
- drop clock-frequency property support;
- move ethtool operations to separate patchset.
Changes v1->v2:
- new patch "phy: provide accessors for 'advertising' and 'supported' fields";
- disable both gigabit advertisement and support;
- drop MDIO bus frequency configurability, always configure for standard 2.5MHz;
- allow using common clock framework to provide ethoc clock;
- new patch: "net: ethoc: implement ethtool operations";
- drop device tree bindings documentation patch until common bindings format for network drivers is decided.
Max Filippov (2):
net: ethoc: don't advertise gigabit speed on attached PHY
net: ethoc: set up MII management bus clock
drivers/net/ethernet/ethoc.c | 37 +++++++++++++++++++++++++++++++++++-- include/net/ethoc.h | 1 + 2 files changed, 36 insertions(+), 2 deletions(-)
Signature · 1 line
1.8.1.4
PATCH v3 1/2 net: ethoc: don't advertise gigabit speed on attached PHY
OpenCores 10/100 Mbps MAC does not support speeds above 100 Mbps, but does not disable advertisement when PHY supports them. This results in non-functioning network when the MAC is connected to a gigabit PHY connected to a gigabit switch.
The fix is to disable gigabit speed advertisement on attached PHY unconditionally.
---
Changes v2->v3:
- don't call phy_start_aneg to force phylib to disable gigabit advertisement.
Changes v1->v2:
- disable both gigabit advertisement and support.
drivers/net/ethernet/ethoc.c | 5 +++++ 1 file changed, 5 insertions(+)
drivers/net/ethernet/ethoc.c +5 -0
@@ -691,6 +691,11 @@ static int ethoc_mdio_probe(struct net_device *dev) } priv->phy = phy; + phy->advertising &= ~(ADVERTISED_1000baseT_Full | + ADVERTISED_1000baseT_Half); + phy->supported &= ~(SUPPORTED_1000baseT_Full | + SUPPORTED_1000baseT_Half); +return 0 ; }
Signature · 1 line
1.8.1.4
PATCH v3 2/2 net: ethoc: set up MII management bus clock
In reply to Max FilippovMII management bus clock is derived from the MAC clock by dividing it by MIIMODER register CLKDIV field value. This value may need to be set up in case it is undefined or its default value is too high (and communication with PHY is too slow) or too low (and communication with PHY is impossible). The value of CLKDIV is not specified directly, but is derived from the MAC clock for the default MII management bus frequency of 2.5MHz. The MAC clock may be specified in the platform data, or in the 'clocks' device tree attribute.
---
Changes v2->v3:
- drop clock-frequency property support.
Changes v1->v2:
- drop MDIO bus frequency configurability, always configure for standard 2.5MHz;
- allow using common clock framework to provide ethoc clock.
drivers/net/ethernet/ethoc.c | 32 ++++++++++++++++++++++++++++++-- include/net/ethoc.h | 1 + 2 files changed, 31 insertions(+), 2 deletions(-)
drivers/net/ethernet/ethoc.c +30 -2
@@ -13,6 +13,7 @@#include <linux/dma-mapping.h> #include <linux/etherdevice.h> +#include <linux/clk.h> #include <linux/crc32.h> #include <linux/interrupt.h> #include <linux/io.h>
@@ -219,6 +220,7 @@ struct ethoc {struct phy_device *phy;struct mii_bus *mdio; +struct clk *clk;s8 phy_id; };
@@ -1021,6 +1023,8 @@ static int ethoc_probe(struct platform_device *pdev)int num_bd;int ret =0 ;bool random_mac = false; +struct ethoc_platform_data *pdata =dev_get_platdata (&pdev->dev); +u32 eth_clkfreq = pdata ? pdata->eth_clkfreq :0 ;/* allocate networking device */ netdev =alloc_etherdev (sizeof (struct ethoc ));
@@ -1135,8 +1139,7 @@ static int ethoc_probe(struct platform_device *pdev) }/* Allow the platform setup code to pass in a MAC address. */ -if (dev_get_platdata (&pdev->dev)) { -struct ethoc_platform_data *pdata =dev_get_platdata (&pdev->dev); +if (pdata) {memcpy (netdev->dev_addr, pdata->hwaddr,IFHWADDRLEN ); priv->phy_id = pdata->phy_id; }else {
@@ -1174,6 +1177,27 @@ static int ethoc_probe(struct platform_device *pdev)if (random_mac) netdev->addr_assign_type =NET_ADDR_RANDOM ; +/* Allow the platform setup code to adjust MII management bus clock. */ +if (!eth_clkfreq) { +struct clk *clk =devm_clk_get (&pdev->dev,NULL ); + +if (!IS_ERR (clk)) { + priv->clk = clk; +clk_prepare_enable (clk); + eth_clkfreq =clk_get_rate (clk); + } + } +if (eth_clkfreq) { +u32 clkdiv =MIIMODER_CLKDIV (eth_clkfreq /2500000 +1 ); + +if (!clkdiv) + clkdiv =2 ; +dev_dbg (&pdev->dev,"setting MII clkdiv to %u\n" , clkdiv); +ethoc_write (priv,MIIMODER , + (ethoc_read (priv,MIIMODER ) &MIIMODER_NOPRE ) | + clkdiv); + } +/* register MII bus */ priv->mdio =mdiobus_alloc ();if (!priv->mdio) {
@@ -1239,6 +1263,8 @@ free_mdio:kfree (priv->mdio->irq);mdiobus_free (priv->mdio); free: +if (priv->clk) +clk_disable_unprepare (priv->clk);free_netdev (netdev); out:return ret;
@@ -1263,6 +1289,8 @@ static int ethoc_remove(struct platform_device *pdev)kfree (priv->mdio->irq);mdiobus_free (priv->mdio); } +if (priv->clk) +clk_disable_unprepare (priv->clk);unregister_netdev (netdev);free_netdev (netdev); }
include/net/ethoc.h +1 -0
@@ -16,6 +16,7 @@struct ethoc_platform_data {u8 hwaddr[IFHWADDRLEN ];s8 phy_id; +u32 eth_clkfreq; };#endif /* !LINUX_NET_ETHOC_H */
Signature · 1 line
1.8.1.4
David Miller
maintainerFrom: Max Filippov <[email protected]>
Date: Tue, 4 Feb 2014 03:33:08 +0400
Quoted 10 lines
Hello David, Ben, Florian, Chris and everybody,
this series improves ethoc behavior in gigabit environment:
- first patch disables gigabit advertisement in the attached PHY making possible to use gigabit link without any additional setup;
- second patch adds support to set up MII management bus frequency, adding new fields to platform data and to OF bindings.These changes allow to use KC-705 board with 50MHz xtensa core and OpenCores 10/100 Mbps MAC connected to gigabit network without any additional setup.
Both patches applied, thanks.