hwmon: Driver for Linear Technologies LTC2945
Subsystems (2)
Guenter Roeck
maintainerPATCH v2 1/1 hwmon: Driver for Linear Technologies LTC2945
LTC2945 is a system monitor that measures current, voltage, and power.
Signed-off-by Guenter Roeck <[email protected]>
---
v2: Fixed 'undefined reference to __udivdi3' on 32 bit systems
Dropped unnecessary include of init.h.
Documentation/hwmon/ltc2945 | 84 +++++++ drivers/hwmon/Kconfig | 12 + drivers/hwmon/Makefile | 1 + drivers/hwmon/ltc2945.c | 519 +++++++++++++++++++++++++++++++++++++++++++ 4 files changed, 616 insertions(+) create mode 100644 Documentation/hwmon/ltc2945 create mode 100644 drivers/hwmon/ltc2945.c
Documentation/hwmon/ltc2945 new file +83 -0
@@ -0,0 +1,84 @@ +Kernel driver ltc2945 +==========+ +Supported chips: + * Linear Technology LTC2945 + Prefix: 'ltc2945' + Addresses scanned: - + Datasheet: + http://cds.linear.com/docs/en/datasheet/2945fa.pdf + +Author: Guenter Roeck <[email protected]> + + +Description +----------- + +The LTC2945 is a rail-to-rail system monitor that measures current, voltage, +and power consumption. + + +Usage Notes +----------- + +This driver does not probe for LTC2945 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for an LTC2945 at address 0x10 +on I2C bus #1: +$ modprobe ltc2945 +$ echo ltc2945 0x10 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +Voltage readings provided by this driver are reported as obtained from the ADC +registers. If a set of voltage divider resistors is installed, calculate the +real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the +value of the divider resistor against the measured voltage and R2 is the value +of the divider resistor against Ground. + +Current reading provided by this driver is reported as obtained from the ADC +Current Sense register. The reported value assumes that a 1 mOhm sense resistor +is installed. If a different sense resistor is installed, calculate the real +current by dividing the reported value by the sense resistor value in mOhm. + +in1_input VIN voltage (mV). Voltage is measured either at + SENSE+ or VDD pin depending on chip configuration. +in1_min Undervoltage threshold +in1_max Overvoltage threshold +in1_lowest Lowest measured voltage +in1_highest Highest measured voltage +in1_reset_history Write 1 to reset in1 history +in1_min_alarm Undervoltage alarm +in1_max_alarm Overvoltage alarm + +in2_input ADIN voltage (mV) +in2_min Undervoltage threshold +in2_max Overvoltage threshold +in2_lowest Lowest measured voltage +in2_highest Highest measured voltage +in2_reset_history Write 1 to reset in2 history +in2_min_alarm Undervoltage alarm +in2_max_alarm Overvoltage alarm + +curr1_input SENSE current (mA) +curr1_min Undercurrent threshold +curr1_max Overcurrent threshold +curr1_lowest Lowest measured current +curr1_highest Highest measured current +curr1_reset_history Write 1 to reset curr1 history +curr1_min_alarm Undercurrent alarm +curr1_max_alarm Overcurrent alarm + +power1_input Power (in uW). Power is calculated based on SENSE+/VDD + voltage or ADIN voltage depending on chip configuration. +power1_min Low lower threshold +power1_max High power threshold +power1_input_lowest Historical minimum power use +power1_input_highest Historical maximum power use +power1_reset_history Write 1 to reset power1 history +power1_min_alarm Low power alarm +power1_max_alarm High power alarm
drivers/hwmon/Kconfig +12 -0
@@ -776,6 +776,18 @@ config SENSORS_LM93 This driver can also be built as a module. If so, the module will be called lm93. +config SENSORS_LTC2945 + tristate "Linear Technology LTC2945" + depends on I2C + select REGMAP_I2C + default n + help + If you say yes here you get support for Linear Technology LTC2945 + I2C System Monitor. + + This driver can also be built as a module. If so, the module will + be called ltc2945. + config SENSORS_LTC4151 tristate "Linear Technology LTC4151" depends on I2C
drivers/hwmon/Makefile +1 -0
@@ -95,6 +95,7 @@ obj-$(CONFIG_SENSORS_LM93) += lm93.o obj-$(CONFIG_SENSORS_LM95234) += lm95234.o obj-$(CONFIG_SENSORS_LM95241) += lm95241.o obj-$(CONFIG_SENSORS_LM95245) += lm95245.o +obj-$(CONFIG_SENSORS_LTC2945) += ltc2945.o obj-$(CONFIG_SENSORS_LTC4151) += ltc4151.o obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o obj-$(CONFIG_SENSORS_LTC4222) += ltc4222.o
drivers/hwmon/ltc2945.c new file +519 -0
519 lines not on this page · raw message
Signature · 7 lines
1.7.9.7 _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors