ARM: add minimal support for the Freescale Quad UDOO Board
Subsystems (4)
PATCH v2 1/2 ARM: add minimal support for the Freescale Quad UDOO Board
Adding minimal support for the UDOO board.
For more information about the board: http://www.udoo.org/
--- arch/arm/boards/Makefile | 1 + arch/arm/boards/udoo/Makefile | 3 + arch/arm/boards/udoo/board.c | 204 ++++++++++++++++++++++ arch/arm/boards/udoo/env/config-board | 6 + arch/arm/boards/udoo/flash-header-mx6-udoo.imxcfg | 104 +++++++++++ arch/arm/boards/udoo/lowlevel.c | 17 ++ arch/arm/configs/imx_v7_defconfig | 1 + arch/arm/dts/Makefile | 4 +- arch/arm/dts/imx6q-udoo.dts | 22 +++ arch/arm/dts/imx6qdl-udoo.dtsi | 111 ++++++++++++ arch/arm/mach-imx/Kconfig | 5 + images/Makefile.imx | 5 + 12 files changed, 482 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boards/udoo/Makefile create mode 100644 arch/arm/boards/udoo/board.c create mode 100644 arch/arm/boards/udoo/env/config-board create mode 100644 arch/arm/boards/udoo/flash-header-mx6-udoo.imxcfg create mode 100644 arch/arm/boards/udoo/lowlevel.c create mode 100644 arch/arm/dts/imx6q-udoo.dts create mode 100644 arch/arm/dts/imx6qdl-udoo.dtsi
arch/arm/boards/Makefile +1 -0
@@ -91,6 +91,7 @@ obj-$(CONFIG_MACH_TX25) += karo-tx25/ obj-$(CONFIG_MACH_TX28) += karo-tx28/ obj-$(CONFIG_MACH_TX51) += karo-tx51/ obj-$(CONFIG_MACH_TX53) += karo-tx53/ +obj-$(CONFIG_MACH_UDOO) += udoo/ obj-$(CONFIG_MACH_USB_A9260) += usb-a926x/ obj-$(CONFIG_MACH_USB_A9263) += usb-a926x/ obj-$(CONFIG_MACH_USB_A9G20) += usb-a926x/
arch/arm/boards/udoo/Makefile new file +3 -0
@@ -0,0 +1,3 @@ +obj-y += board.o flash-header-mx6-udoo.dcd.o +extra-y += flash-header-mx6-udoo.dcd.S flash-header-mx6-udoo.dcd +lwl-y += lowlevel.o
arch/arm/boards/udoo/board.c new file +204 -0
204 lines not on this page · raw message
arch/arm/boards/udoo/env/config-board new file +6 -0
@@ -0,0 +1,6 @@ +#!/bin/sh + +# board defaults, do not change in running system. Change /env/config +# instead + +global.linux.bootargs.base="console=ttymxc1,115200"
arch/arm/boards/udoo/flash-header-mx6-udoo.imxcfg new file +104 -0
104 lines not on this page · raw message
arch/arm/boards/udoo/lowlevel.c new file +17 -0
@@ -0,0 +1,17 @@ +#include <common.h> +#include <sizes.h> +#include <asm/barebox-arm-head.h> +#include <asm/barebox-arm.h> + +extern char __dtb_imx6q_udoo_start[]; + +ENTRY_FUNCTION(start_imx6_udoo, r0, r1, r2) +{ +uint32_t fdt; + +arm_cpu_lowlevel_init (); + + fdt = (uint32_t )__dtb_imx6q_udoo_start -get_runtime_offset (); + +barebox_arm_entry (0x10000000 ,SZ_1G , fdt); +}
arch/arm/configs/imx_v7_defconfig +1 -0
@@ -13,6 +13,7 @@ CONFIG_MACH_TQMA6X=y CONFIG_MACH_SABRELITE=y CONFIG_MACH_NITROGEN6X=y CONFIG_MACH_SOLIDRUN_HUMMINGBOARD=y +CONFIG_MACH_UDOO=y CONFIG_IMX_IIM=y CONFIG_IMX_IIM_FUSE_BLOW=y CONFIG_IMX_OCOTP=y
arch/arm/dts/Makefile +3 -1
@@ -23,7 +23,8 @@ dtb-$(CONFIG_ARCH_IMX6) += imx6q-gk802.dtb \ imx6q-phytec-pbab01.dtb \ imx6dl-hummingboard.dtb \ imx6q-nitrogen6x.dtb \ - imx6dl-nitrogen6x.dtb + imx6dl-nitrogen6x.dtb \ + imx6q-udoo.dtb dtb-$(CONFIG_ARCH_MVEBU) += dove-cubox.dtb dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_cyclone5_sockit.dtb \ socfpga_cyclone5_socrates.dtb
@@ -55,6 +56,7 @@ pbl-$(CONFIG_MACH_SOCFPGA_TERASIC_SOCKIT) += socfpga_cyclone5_sockit.dtb.o pbl-$(CONFIG_MACH_SOLIDRUN_HUMMINGBOARD) += imx6dl-hummingboard.dtb.o pbl-$(CONFIG_MACH_SABRELITE) += imx6q-sabrelite.dtb.o imx6dl-sabrelite.dtb.o pbl-$(CONFIG_MACH_NITROGEN6X) += imx6q-nitrogen6x.dtb.o imx6dl-nitrogen6x.dtb.o +pbl-$(CONFIG_MACH_UDOO) += imx6q-udoo.dtb.o .SECONDARY: $(obj)/$(BUILTIN_DTB).dtb.S .SECONDARY: $(patsubst %,$(obj)/%.S,$(dtb-y))
arch/arm/dts/imx6q-udoo.dts new file +22 -0
@@ -0,0 +1,22 @@ +/* + * Copyright 2014 Raphaël Poggi + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; + +#include "imx6qdl-udoo.dtsi" + +/ { + model = "Freescale i.MX6 Quad UDOO Board"; + compatible = "fsl,imx6q-udoo", "fsl,imx6q"; +}; +
arch/arm/dts/imx6qdl-udoo.dtsi new file +111 -0
111 lines not on this page · raw message
arch/arm/mach-imx/Kconfig +5 -0
@@ -37,6 +37,7 @@ config ARCH_TEXT_BASE default 0x2fc00000 if MACH_TQMA6X default 0x4fc00000 if MACH_PHYTEC_PFLA02 default 0x4fc00000 if MACH_DFI_FS700_M60 + default 0x4fc00000 if MACH_UDOO config ARCH_IMX_INTERNAL_BOOT bool "support internal boot mode"
@@ -233,6 +234,10 @@ config MACH_SOLIDRUN_HUMMINGBOARD bool "SolidRun Hummingboard" select ARCH_IMX6 +config MACH_UDOO + bool "Freescale i.MX6 UDOO Board" + select ARCH_IMX6 + endif # ----------------------------------------------------------
images/Makefile.imx +5 -0
@@ -123,3 +123,8 @@ pblx-$(CONFIG_MACH_NITROGEN6X) += start_imx6dl_nitrogen6x_1g CFG_start_imx6dl_nitrogen6x_1g.pblx.imximg = $(board)/boundarydevices-nitrogen6x/flash-header-nitrogen6x-1g.imxcfg FILE_barebox-boundarydevices-imx6dl-nitrogen6x-1g.img = start_imx6dl_nitrogen6x_1g.pblx.imximg image-$(CONFIG_MACH_NITROGEN6X) += barebox-boundarydevices-imx6dl-nitrogen6x-1g.img + +pblx-$(CONFIG_MACH_UDOO) += start_imx6_udoo +CFG_start_imx6_udoo.pblx.imximg = $(board)/udoo/flash-header-mx6-udoo.imxcfg +FILE_barebox-freescale-imx6q-udoo.img = start_imx6_udoo.pblx.imximg +image-$(CONFIG_MACH_UDOO) += barebox-freescale-imx6q-udoo.img
Signature · 7 lines
1.8.3.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 2/2 ARM: Rework device tree of UDOO Board to be more flexible.
Device tree of UDOO Board have to be more flexible.
There are a dual imx6 and a quad imx6 boards, with this patch
we can have a same device tree file as a base: arch/arm/dts/imx6qdl-udoo.dtsi and an other device tree file for specific configuration depending of the board.
--- arch/arm/boards/udoo/board.c | 6 +++--- arch/arm/dts/imx6q-udoo.dts | 3 ++- arch/arm/dts/imx6qdl-udoo.dtsi | 5 +++-- 3 files changed, 8 insertions(+), 6 deletions(-)
arch/arm/boards/udoo/board.c +3 -3
@@ -166,7 +166,7 @@ static void udoo_epit_init(void)static int udoo_devices_init (void ) { -if (!of_machine_is_compatible ("fsl,imx6q-udoo" )) +if (!of_machine_is_compatible ("udoo,imx6qdl-udoo" ))return 0 ;setup_iomux_wdog ();
@@ -181,7 +181,7 @@ device_initcall(udoo_devices_init);static int udoo_coredevices_init (void ) { -if (!of_machine_is_compatible ("fsl,imx6q-udoo" )) +if (!of_machine_is_compatible ("udoo,imx6qdl-udoo" ))return 0 ; phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
@@ -192,7 +192,7 @@ coredevice_initcall(udoo_coredevices_init);static int udoo_postcore_init (void ) { -if (!of_machine_is_compatible ("fsl,imx6q-udoo" )) +if (!of_machine_is_compatible ("udoo,imx6qdl-udoo" ))return 0 ;imx6_init_lowlevel ();
arch/arm/dts/imx6q-udoo.dts +2 -1
@@ -13,10 +13,11 @@ /dts-v1/; +#include "imx6q.dtsi" #include "imx6qdl-udoo.dtsi" / { model = "Freescale i.MX6 Quad UDOO Board"; - compatible = "fsl,imx6q-udoo", "fsl,imx6q"; + compatible = "udoo,imx6q-udoo", "udoo,imx6qdl-udoo", "fsl,imx6q"; };
arch/arm/dts/imx6qdl-udoo.dtsi +3 -2
@@ -11,12 +11,13 @@ * http://www.gnu.org/copyleft/gpl.html */ -#include "imx6q.dtsi" - #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/input/input.h> / { + model = "Freescale i.MX6 UDOO Board"; + compatible = "udoo,imx6qdl-udoo", "fsl,imx6q"; + chosen { linux,stdout-path = &uart2;
Signature · 7 lines
1.8.3.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 5 lines · Raphaël POGGI
Adding minimal support for the UDOO board.
For more information about the board: http://www.udoo.org/
Signed-off-by Raphael Poggi <[email protected]>
Applied, thanks
Sascha
Quoted 621 lines
--- arch/arm/boards/Makefile | 1 + arch/arm/boards/udoo/Makefile | 3 + arch/arm/boards/udoo/board.c | 204 ++++++++++++++++++++++ arch/arm/boards/udoo/env/config-board | 6 + arch/arm/boards/udoo/flash-header-mx6-udoo.imxcfg | 104 +++++++++++ arch/arm/boards/udoo/lowlevel.c | 17 ++ arch/arm/configs/imx_v7_defconfig | 1 + arch/arm/dts/Makefile | 4 +- arch/arm/dts/imx6q-udoo.dts | 22 +++ arch/arm/dts/imx6qdl-udoo.dtsi | 111 ++++++++++++ arch/arm/mach-imx/Kconfig | 5 + images/Makefile.imx | 5 + 12 files changed, 482 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boards/udoo/Makefile create mode 100644 arch/arm/boards/udoo/board.c create mode 100644 arch/arm/boards/udoo/env/config-board create mode 100644 arch/arm/boards/udoo/flash-header-mx6-udoo.imxcfg create mode 100644 arch/arm/boards/udoo/lowlevel.c create mode 100644 arch/arm/dts/imx6q-udoo.dts create mode 100644 arch/arm/dts/imx6qdl-udoo.dtsiarch/arm/boards/Makefile +1
-0@@ -91,6 +91,7 @@ obj-$(CONFIG_MACH_TX25) += karo-tx25/ obj-$(CONFIG_MACH_TX28) += karo-tx28/ obj-$(CONFIG_MACH_TX51) += karo-tx51/ obj-$(CONFIG_MACH_TX53) += karo-tx53/ +obj-$(CONFIG_MACH_UDOO) += udoo/ obj-$(CONFIG_MACH_USB_A9260) += usb-a926x/ obj-$(CONFIG_MACH_USB_A9263) += usb-a926x/ obj-$(CONFIG_MACH_USB_A9G20) += usb-a926x/arch/arm/boards/udoo/Makefile new file +3
-0@@ -0,0 +1,3 @@ +obj-y += board.o flash-header-mx6-udoo.dcd.o +extra-y += flash-header-mx6-udoo.dcd.S flash-header-mx6-udoo.dcd +lwl-y += lowlevel.oarch/arm/boards/udoo/board.c new file +204
-0@@ -0,0 +1,204 @@ +/* +* Copyright (C) 2014 Raphaël Poggi +* Copyright (C) 2012 Steffen Trumtrar, Pengutronix +* +* based on arch/arm/boards/freescale-mx6-arm2/board.c +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +*/ + +#include <common.h> +#include <init.h> +#include <environment.h> +#include <mach/imx6-regs.h> +#include <fec.h> +#include <gpio.h> +#include <mach/bbu.h> +#include <asm/armlinux.h> +#include <generated/mach-types.h> +#include <partition.h> +#include <linux/phy.h> +#include <asm/io.h> +#include <asm/mmu.h> +#include <mach/generic.h> +#include <sizes.h> +#include <net.h> +#include <linux/micrel_phy.h> +#include <mach/imx6.h> +#include <mach/devices-imx6.h> +#include <mach/iomux-mx6.h> +#include <spi/spi.h> +#include <mach/spi.h> +#include <mach/usb.h> + +static iomux_v3_cfg_t udoo_enet_gpio_pads_1[] = { +MX6Q_PAD_ENET_MDIO__ENET_MDIO |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_ENET_MDC__ENET_MDC |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_RGMII_TXC__ENET_RGMII_TXC |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_RGMII_TD0__ENET_RGMII_TD0 |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_RGMII_TD1__ENET_RGMII_TD1 |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_RGMII_TD2__ENET_RGMII_TD2 |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_RGMII_TD3__ENET_RGMII_TD3 |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_RGMII_TX_CTL__ENET_RGMII_TX_CTL |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_ENET_REF_CLK__ENET_TX_CLK |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +MX6Q_PAD_RGMII_RXC__ENET_RGMII_RXC |MUX_PAD_CTRL (MX6Q_ENET_PAD_CTRL ), +/* RGMII reset */ +/* alimentazione ethernet*/ +MX6Q_PAD_EIM_EB3__GPIO_2_31 |MUX_PAD_CTRL (NO_PAD_CTRL ), +/* pin 32 - 1 - (MODE0) all */ +MX6Q_PAD_RGMII_RD0__GPIO_6_25 |MUX_PAD_CTRL (NO_PAD_CTRL ), +/* pin 31 - 1 - (MODE1) all */ +MX6Q_PAD_RGMII_RD1__GPIO_6_27 |MUX_PAD_CTRL (NO_PAD_CTRL ), +/* pin 28 - 1 - (MODE2) all */ +MX6Q_PAD_RGMII_RD2__GPIO_6_28 |MUX_PAD_CTRL (NO_PAD_CTRL ), +/* pin 27 - 1 - (MODE3) all */ +MX6Q_PAD_RGMII_RD3__GPIO_6_29 |MUX_PAD_CTRL (NO_PAD_CTRL ), +/* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ +}; + +static iomux_v3_cfg_t udoo_enet_gpio_pads_2[] = { +/* Ethernet */ +MX6Q_PAD_RGMII_RXC__GPIO_6_30 ,/* PHYAD */ +MX6Q_PAD_RGMII_RD0__GPIO_6_25 ,/* MODE0 */ +MX6Q_PAD_RGMII_RD1__GPIO_6_27 ,/* MODE1 */ +MX6Q_PAD_RGMII_RD2__GPIO_6_28 ,/* MODE2 */ +MX6Q_PAD_RGMII_RD3__GPIO_6_29 ,/* MODE3 */ +MX6Q_PAD_RGMII_RX_CTL__GPIO_6_24 , +}; + +static int ksz9021rn_phy_fixup (struct phy_device *dev) +{ + +phy_write (dev,0x09 ,0x1c00 ); +phy_write (dev,0x4 ,0x0000 ); +phy_write (dev,0x5 ,0x0000 ); +phy_write (dev,0x6 ,0x0000 ); +phy_write (dev,0x8 ,0x03ff ); + +/* do same as linux kernel */ +/* min rx data delay */ +phy_write (dev,0x0b ,0x8105 ); +phy_write (dev,0x0c ,0x0000 ); + +/* max rx/tx clock delay, min rx/tx control delay */ +phy_write (dev,0x0b ,0x8104 ); +phy_write (dev,0x0c ,0xf0f0 ); +phy_write (dev,0x0b ,0x104 ); + +return 0 ; +} + +static int udoo_ksz9021rn_setup (void ) +{ +mxc_iomux_v3_setup_multiple_pads (udoo_enet_gpio_pads_1, +ARRAY_SIZE (udoo_enet_gpio_pads_1)); + +gpio_direction_output (IMX_GPIO_NR (2 ,31 ) ,1 );/* Power on enet */ + +/* MODE strap-in pins: advertise all capabilities */ +gpio_direction_output (185 ,1 );/* GPIO 6-25 */ +gpio_direction_output (187 ,1 );/* GPIO 6-27 */ +gpio_direction_output (188 ,1 );/* GPIO 6-28*/ +gpio_direction_output (189 ,1 );/* GPIO 6-29 */ + +mdelay (10 ); + +/* Enable 125 MHz clock output */ +gpio_direction_output (184 ,1 );/* GPIO 6-24 */ + +mdelay (100 ); + +gpio_free (IMX_GPIO_NR (6 ,24 )); +gpio_free (IMX_GPIO_NR (6 ,25 )); +gpio_free (IMX_GPIO_NR (6 ,27 )); +gpio_free (IMX_GPIO_NR (6 ,28 )); +gpio_free (IMX_GPIO_NR (6 ,29 )); + +mxc_iomux_v3_setup_multiple_pads (udoo_enet_gpio_pads_2,ARRAY_SIZE (udoo_enet_gpio_pads_2)); + +return 0 ; +} +/* +* Do this before the fec initializes but after our +* gpios are available. +*/ +fs_initcall (udoo_ksz9021rn_setup); + +static void udoo_ehci_init (void ) +{ +/* hub reset */ +gpio_direction_output (204 ,0 ); +udelay (2000 ); +gpio_set_value (204 ,1 ); +} + +static iomux_v3_cfg_t const wdog_pads[] = { +MX6Q_PAD_EIM_A24__GPIO_5_4 |MUX_PAD_CTRL (NO_PAD_CTRL ), +MX6Q_PAD_EIM_D19__EPIT1_EPITO , +}; + +#define WDT_EN IMX_GPIO_NR(5, 4) +#define WDT_TRG IMX_GPIO_NR(3, 19) +static void setup_iomux_wdog (void ) +{ +mxc_iomux_v3_setup_multiple_pads (wdog_pads,ARRAY_SIZE (wdog_pads)); +gpio_direction_output (WDT_TRG ,0 ); +gpio_direction_output (WDT_EN ,1 ); +gpio_direction_input (WDT_TRG ); +} + +static void udoo_epit_init (void ) +{ + +writel (0x0000000 ,0x20D0000 ); +writel (0x142000F ,0x20D0000 ); +writel (0x10000 ,0x20D0008 ); +writel (0x0 ,0x20D000C ); +} + +static int udoo_devices_init (void ) +{ +if (!of_machine_is_compatible ("fsl,imx6q-udoo" )) +return 0 ; + +setup_iomux_wdog (); +udoo_ehci_init (); +udoo_epit_init (); + +armlinux_set_bootparams ((void *)0x10000100 ); + +return 0 ; +} +device_initcall (udoo_devices_init); + +static int udoo_coredevices_init (void ) +{ +if (!of_machine_is_compatible ("fsl,imx6q-udoo" )) +return 0 ; + +phy_register_fixup_for_uid (PHY_ID_KSZ9021 ,MICREL_PHY_ID_MASK , + ksz9021rn_phy_fixup); +return 0 ; +} +coredevice_initcall (udoo_coredevices_init); + +static int udoo_postcore_init (void ) +{ +if (!of_machine_is_compatible ("fsl,imx6q-udoo" )) +return 0 ; + +imx6_init_lowlevel (); + +barebox_set_hostname ("udoo" ); + +return 0 ; +} +postcore_initcall (udoo_postcore_init);arch/arm/boards/udoo/env/config-board new file +6
-0@@ -0,0 +1,6 @@ +#!/bin/sh + +# board defaults, do not change in running system. Change /env/config +# instead + +global.linux.bootargs.base="console=ttymxc1,115200"arch/arm/boards/udoo/flash-header-mx6-udoo.imxcfg new file +104
-0@@ -0,0 +1,104 @@ +soc imx6 +loadaddr 0x20000000 +dcdofs 0x400 + + +/* MX6_IOM_DRAM_SDQS0 -> MX6_IOM_DRAM_SDQS7 */ +wm 32 0x020e05a8 0x00000030 +wm 32 0x020e05b0 0x00000030 +wm 32 0x020e0524 0x00000030 +wm 32 0x020e051c 0x00000030 +wm 32 0x020e0518 0x00000030 +wm 32 0x020e050c 0x00000030 +wm 32 0x020e05b8 0x00000030 +wm 32 0x020e05c0 0x00000030 +/********************************************/ + +/* MX6_IOM_DRAM_DQM0 -> MX6_IOM_DRAM_DQM7 */ +wm 32 0x020e05ac 0x00020030 +wm 32 0x020e05b4 0x00020030 +wm 32 0x020e0528 0x00020030 +wm 32 0x020e0520 0x00020030 +wm 32 0x020e0514 0x00020030 +wm 32 0x020e0510 0x00020030 +wm 32 0x020e05bc 0x00020030 +wm 32 0x020e05c4 0x00020030 +/******************************************/ + +wm 32 0x020e056c 0x00020030 /* MX6_IOM_DRAM_CAS */ +wm 32 0x020e0578 0x00020030 /* MX6_IOM_DRAM_RAS */ +wm 32 0x020e0588 0x00020030 /* MX6_IOM_DRAM_SDCLK_0 */ +wm 32 0x020e0594 0x00020030 /* MX6_IOM_DRAM_SDCLK_1 */ +wm 32 0x020e057c 0x00020030 /* MX6_IOM_DRAM_RESET */ +wm 32 0x020e0590 0x00003000 +wm 32 0x020e0598 0x00003000 +wm 32 0x020e058c 0x00000000 +wm 32 0x020e059c 0x00003030 +wm 32 0x020e05a0 0x00003030 + +/* MX6_IOM_GRP_B0DS -> MX6_IOM_GRP_B7DS */ +wm 32 0x020e0784 0x00000030 +wm 32 0x020e0788 0x00000030 +wm 32 0x020e0794 0x00000030 +wm 32 0x020e079c 0x00000030 +wm 32 0x020e07a0 0x00000030 +wm 32 0x020e07a4 0x00000030 +wm 32 0x020e07a8 0x00000030 +wm 32 0x020e0748 0x00000030 +/***************************************/ + +wm 32 0x020e074c 0x00000030 /* MX6_IOM_GRP_ADDDS */ +wm 32 0x020e0750 0x00020000 +wm 32 0x020e0758 0x00000000 +wm 32 0x020e0774 0x00020000 +wm 32 0x020e078c 0x00000030 /* MX6_IOM_GRP_CTLDS */ +wm 32 0x020e0798 0x000c0000 +wm 32 0x021b081c 0x33333333 +wm 32 0x021b0820 0x33333333 +wm 32 0x021b0824 0x33333333 +wm 32 0x021b0828 0x33333333 +wm 32 0x021b481c 0x33333333 +wm 32 0x021b4820 0x33333333 +wm 32 0x021b4824 0x33333333 +wm 32 0x021b4828 0x33333333 + + +wm 32 0x021b0004 0x00020036 +wm 32 0x021b0008 0x09444040 +wm 32 0x021b000c 0x54597955 +wm 32 0x021b0010 0xFF328F64 +wm 32 0x021b0014 0x01FF00DB +wm 32 0x021b0018 0x00001740 +wm 32 0x021b001c 0x00008000 +wm 32 0x021b002c 0x000026D2 +wm 32 0x021b0030 0x00591023 +wm 32 0x021b0040 0x00000027 +wm 32 0x021b0000 0x831A0000 +wm 32 0x021b001c 0x04088032 +wm 32 0x021b001c 0x00008033 +wm 32 0x021b001c 0x00048031 +wm 32 0x021b001c 0x09408030 +wm 32 0x021b001c 0x04008040 +wm 32 0x021b0800 0xA1380003 +wm 32 0x021b4800 0xA1380003 +wm 32 0x021b0020 0x00005800 +wm 32 0x021b0818 0x00011117 +wm 32 0x021b4818 0x00011117 +wm 32 0x021b083c 0x43510360 +wm 32 0x021b0840 0x0342033F +wm 32 0x021b483c 0x033F033F +wm 32 0x021b4840 0x03290266 +wm 32 0x021b0848 0x4B3E4141 +wm 32 0x021b4848 0x47413B4A +wm 32 0x021b0850 0x42404843 +wm 32 0x021b4850 0x4C3F4C45 +wm 32 0x021b080c 0x00350035 +wm 32 0x021b0810 0x001F001F +wm 32 0x021b480c 0x00010001 +wm 32 0x021b4810 0x00010001 +wm 32 0x021b08b8 0x00000800 +wm 32 0x021b48b8 0x00000800 +wm 32 0x021b0004 0x00025576 +wm 32 0x021b0404 0x00011006 +wm 32 0x021b001c 0x00000000 +arch/arm/boards/udoo/lowlevel.c new file +17
-0@@ -0,0 +1,17 @@ +#include <common.h> +#include <sizes.h> +#include <asm/barebox-arm-head.h> +#include <asm/barebox-arm.h> + +extern char __dtb_imx6q_udoo_start[]; + +ENTRY_FUNCTION(start_imx6_udoo, r0, r1, r2) +{ +uint32_t fdt; + +arm_cpu_lowlevel_init (); + + fdt = (uint32_t )__dtb_imx6q_udoo_start -get_runtime_offset (); + +barebox_arm_entry (0x10000000 ,SZ_1G , fdt); +}arch/arm/configs/imx_v7_defconfig +1
-0@@ -13,6 +13,7 @@ CONFIG_MACH_TQMA6X=y CONFIG_MACH_SABRELITE=y CONFIG_MACH_NITROGEN6X=y CONFIG_MACH_SOLIDRUN_HUMMINGBOARD=y +CONFIG_MACH_UDOO=y CONFIG_IMX_IIM=y CONFIG_IMX_IIM_FUSE_BLOW=y CONFIG_IMX_OCOTP=yarch/arm/dts/Makefile +3
-1@@ -23,7 +23,8 @@ dtb-$(CONFIG_ARCH_IMX6) += imx6q-gk802.dtb \ imx6q-phytec-pbab01.dtb \ imx6dl-hummingboard.dtb \ imx6q-nitrogen6x.dtb \ - imx6dl-nitrogen6x.dtb + imx6dl-nitrogen6x.dtb \ + imx6q-udoo.dtb dtb-$(CONFIG_ARCH_MVEBU) += dove-cubox.dtb dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_cyclone5_sockit.dtb \ socfpga_cyclone5_socrates.dtb@@ -55,6 +56,7 @@ pbl-$(CONFIG_MACH_SOCFPGA_TERASIC_SOCKIT) += socfpga_cyclone5_sockit.dtb.o pbl-$(CONFIG_MACH_SOLIDRUN_HUMMINGBOARD) += imx6dl-hummingboard.dtb.o pbl-$(CONFIG_MACH_SABRELITE) += imx6q-sabrelite.dtb.o imx6dl-sabrelite.dtb.o pbl-$(CONFIG_MACH_NITROGEN6X) += imx6q-nitrogen6x.dtb.o imx6dl-nitrogen6x.dtb.o +pbl-$(CONFIG_MACH_UDOO) += imx6q-udoo.dtb.o .SECONDARY: $(obj)/$(BUILTIN_DTB).dtb.S .SECONDARY: $(patsubst %,$(obj)/%.S,$(dtb-y))arch/arm/dts/imx6q-udoo.dts new file +22
-0@@ -0,0 +1,22 @@ +/* + * Copyright 2014 Raphaël Poggi + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; + +#include "imx6qdl-udoo.dtsi" + +/ { + model = "Freescale i.MX6 Quad UDOO Board"; + compatible = "fsl,imx6q-udoo", "fsl,imx6q"; +}; +arch/arm/dts/imx6qdl-udoo.dtsi new file +111
-0@@ -0,0 +1,111 @@ +/* + * Copyright 2014 Raphaël Poggi + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include "imx6q.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + chosen { + linux,stdout-path = &uart2; + + }; + + memory { + reg = <0x10000000 0x40000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_2p5v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6q-udoo { + pinctrl_hog: hoggrp { + fsl,pins = < + /* SGTL5000 sys_mclk */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = <MX6QDL_I2C1_PINGRP1>; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = <MX6QDL_UART2_PINGRP1>; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_USDHC3_PINGRP_D4 + >; + }; + + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + status = "okay"; +};arch/arm/mach-imx/Kconfig +5
-0@@ -37,6 +37,7 @@ config ARCH_TEXT_BASE default 0x2fc00000 if MACH_TQMA6X default 0x4fc00000 if MACH_PHYTEC_PFLA02 default 0x4fc00000 if MACH_DFI_FS700_M60 + default 0x4fc00000 if MACH_UDOO config ARCH_IMX_INTERNAL_BOOT bool "support internal boot mode"@@ -233,6 +234,10 @@ config MACH_SOLIDRUN_HUMMINGBOARD bool "SolidRun Hummingboard" select ARCH_IMX6 +config MACH_UDOO + bool "Freescale i.MX6 UDOO Board" + select ARCH_IMX6 + endif # ----------------------------------------------------------images/Makefile.imx +5
-0@@ -123,3 +123,8 @@ pblx-$(CONFIG_MACH_NITROGEN6X) += start_imx6dl_nitrogen6x_1g CFG_start_imx6dl_nitrogen6x_1g.pblx.imximg = $(board)/boundarydevices-nitrogen6x/flash-header-nitrogen6x-1g.imxcfg FILE_barebox-boundarydevices-imx6dl-nitrogen6x-1g.img = start_imx6dl_nitrogen6x_1g.pblx.imximg image-$(CONFIG_MACH_NITROGEN6X) += barebox-boundarydevices-imx6dl-nitrogen6x-1g.img + +pblx-$(CONFIG_MACH_UDOO) += start_imx6_udoo +CFG_start_imx6_udoo.pblx.imximg = $(board)/udoo/flash-header-mx6-udoo.imxcfg +FILE_barebox-freescale-imx6q-udoo.img = start_imx6_udoo.pblx.imximg +image-$(CONFIG_MACH_UDOO) += barebox-freescale-imx6q-udoo.imgSignature · 7 lines
1.8.3.2 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox