brcmfmac: driver cleanup and rework
Subsystems (3)
cover brcmfmac: driver cleanup and rework
This series includes a number of cleanup changes and rework mainly in the sdio driver. These are intended for 3.15 kernel and apply on the master branch of the wireless-next repository.
Arend van Spriel (5):
brcmfmac: add delay before unregistering the network device
brcmfmac: fix use of skb control buffer in SDIO driver part
brcmfmac: remove unused variable data_len from
brcmf_sdio_bus_txdata()
brcmfmac: use pre-allocated scatter-gather table for txglomming
brcmfmac: reset suspend flag upon sdio suspend failure
Daniel Kim (1):
brcmfmac: Correct mcs index report
Hante Meuleman (8):
brcmfmac: Make firmeware roaming a module param.
brcmfmac: Correct header debug dump for sdio tx hdrs.
brcmfmac: de-init driver layers in correct order.
brcmfmac: Minimize SDIO dpc scheduling.
brcmfmac: Remove immediate sleep support from SDIO.
brcmfmac: Small cleanup of redundant code.
brcmfmac: Use atomic functions for intstatus update.
brcmfmac: Put frame sdio tx error handling in sub function.
drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 53 +++-- .../net/wireless/brcm80211/brcmfmac/dhd_linux.c | 8 +- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 209 +++++++------------- .../net/wireless/brcm80211/brcmfmac/sdio_host.h | 2 + .../net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 64 +++--- .../net/wireless/brcm80211/brcmfmac/wl_cfg80211.h | 1 - 6 files changed, 154 insertions(+), 183 deletions(-)
Signature · 1 line
1.7.10.4
PATCH 1/14 brcmfmac: add delay before unregistering the network device
Upon deleting the interface a cfg80211_disconnected() is called under rtnl_lock. Right after the unlocking the rtnl_lock we unregister the network device. This patch adds delay before unregister so cfg80211 can handle disconnect and notify wpa_supplicant.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c | 4 ++++ drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 9 +-------- 2 files changed, 5 insertions(+), 8 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c +4 -0
@@ -848,6 +848,10 @@ void brcmf_del_if(struct brcmf_pub *drvr, s32 bssidx)rtnl_lock ();brcmf_netdev_stop (ifp->ndev);rtnl_unlock (); +/* make sure cfg80211 can send disconnect event +* before unregistering the netdevice below. +*/ +msleep (100 ); } }else {netif_stop_queue (ifp->ndev);
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c +1 -8
@@ -5443,16 +5443,9 @@ static s32 __brcmf_cfg80211_down(struct brcmf_if *ifp)* While going down, if associated with AP disassociate * from AP to save power */ -if (check_vif_up (ifp->vif)) { +if (check_vif_up (ifp->vif))brcmf_link_down (ifp->vif); -/* Make sure WPA_Supplicant receives all the event -generated due to DISASSOC call to the fw to keep -the state fw and WPA_Supplicant state consistent -*/ -brcmf_delay (500 ); - } -brcmf_abort_scanning (cfg);clear_bit (BRCMF_VIF_STATUS_READY , &ifp->vif->sme_state);
Signature · 1 line
1.7.10.4
Johannes Berg
maintainerRe: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c void brcmf_del_if(struct brcmf_pub *drvr, s32 bssidx) · line 854
Quoted 9 lines · Arend van Spriel
Upon deleting the interface a
cfg80211_disconnected()is called underrtnl_lock. Right after the unlocking thertnl_lockwe unregister the network device. This patch adds delay before unregister so cfg80211 can handle disconnect and notifywpa_supplicant.drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c +4
-0+/* make sure cfg80211 can send disconnect event +* before unregistering the netdevice below. +*/ +msleep (100 );
This has got to be one of the worst hacks I've seen in wireless so far ... :)
johannes
Re: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 6 lines · Johannes Berg
Quoted 4 lines · Arend van Spriel
Upon deleting the interface a
cfg80211_disconnected()is called underrtnl_lock. Right after the unlocking thertnl_lockwe unregister the network device. This patch adds delay before unregister so cfg80211 can handle disconnect and notifywpa_supplicant.
Quoted 7 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c void brcmf_del_if(struct brcmf_pub *drvr, s32 bssidx) · line 854
Quoted 4 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c +4
-0+/* make sure cfg80211 can send disconnect event +* before unregistering the netdevice below. +*/ +msleep (100 );This has got to be one of the worst hacks I've seen in wireless so far ... :)
Did you see I removed a sleep as well in this patch :-p
I just don't see how I can assure cfg80211 has actually done the disconnect work. If we don't do a cfg80211_disconnected() I get a WARN from the cfg80211 netdev notifier (or at least I did in previous kernel).
Should we consider a clean solution, ie. modify cfg80211 for this scenario?
Gr. AvS
Johannes Berg
maintainerRe: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 15 lines · Arend van Spriel
Quoted 6 lines · Johannes Berg
Quoted 4 lines · Arend van Spriel
Upon deleting the interface a
cfg80211_disconnected()is called underrtnl_lock. Right after the unlocking thertnl_lockwe unregister the network device. This patch adds delay before unregister so cfg80211 can handle disconnect and notifywpa_supplicant.Quoted 7 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c void brcmf_del_if(struct brcmf_pub *drvr, s32 bssidx) · line 854
Quoted 4 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c +4
-0+/* make sure cfg80211 can send disconnect event +* before unregistering the netdevice below. +*/ +msleep (100 );This has got to be one of the worst hacks I've seen in wireless so far ... :)
Quoted 1 line
Did you see I removed a sleep as well in this patch :-p
Yeah, I did :-)
Quoted 5 lines
I just don't see how I can assure cfg80211 has actually done the disconnect work. If we don't do a
cfg80211_disconnected()I get a WARN from the cfg80211 netdev notifier (or at least I did in previous kernel).Should we consider a clean solution, ie. modify cfg80211 for this scenario?
Yes. Can't we just flush the work at some strategic place?
Actually you're not talking about the "disconnect_work" (which is related to regulatory) but the "event_work" so I was confused here for a second.
What was the warning? cfg80211 already calls cfg80211_process_wdev_events() from within the REMOVE netdev notifier, so that *shouldn't* have happened.
johannes
Re: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 28 lines · Johannes Berg
Quoted 15 lines · Arend van Spriel
Quoted 6 lines · Johannes Berg
Quoted 4 lines · Arend van Spriel
Upon deleting the interface a
cfg80211_disconnected()is called underrtnl_lock. Right after the unlocking thertnl_lockwe unregister the network device. This patch adds delay before unregister so cfg80211 can handle disconnect and notifywpa_supplicant.Quoted 7 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c void brcmf_del_if(struct brcmf_pub *drvr, s32 bssidx) · line 854
Quoted 4 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c +4
-0+/* make sure cfg80211 can send disconnect event +* before unregistering the netdevice below. +*/ +msleep (100 );This has got to be one of the worst hacks I've seen in wireless so far ... :)
Quoted 1 line
Did you see I removed a sleep as well in this patch :-p
Yeah, I did :-)
Quoted 5 lines
I just don't see how I can assure cfg80211 has actually done the disconnect work. If we don't do a
cfg80211_disconnected()I get a WARN from the cfg80211 netdev notifier (or at least I did in previous kernel).Should we consider a clean solution, ie. modify cfg80211 for this scenario?
Yes. Can't we just flush the work at some strategic place?
Quoted 7 lines
Actually you're not talking about the "
disconnect_work" (which is related to regulatory) but the "event_work" so I was confused here for a second.What was the warning? cfg80211 already calls
cfg80211_process_wdev_events()from within the REMOVE netdev notifier, so that *shouldn't* have happened.
I guess that means some wdev event is missing? It was the WARN_ON(current->bss) that fired.
Gr. AvS
Johannes Berg
maintainerRe: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 6 lines · Arend van Spriel
Quoted 6 lines
Yes. Can't we just flush the work at some strategic place?
Actually you're not talking about the "
disconnect_work" (which is related to regulatory) but the "event_work" so I was confused here for a second.
Quoted 6 lines
Quoted 3 lines
What was the warning? cfg80211 already calls
cfg80211_process_wdev_events()from within the REMOVE netdev notifier, so that *shouldn't* have happened.I guess that means some wdev event is missing? It was the
WARN_ON(current->bss)that fired.
Hmm, that's odd, the process_wdev_events() call is right before that, so I don't see how that could have happened?
johannes
Re: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 12 lines · Johannes Berg
Quoted 10 lines · Arend van Spriel
Quoted 9 lines
Yes. Can't we just flush the work at some strategic place?
Actually you're not talking about the "
disconnect_work" (which is related to regulatory) but the "event_work" so I was confused here for a second.What was the warning? cfg80211 already calls
cfg80211_process_wdev_events()from within the REMOVE netdev notifier, so that *shouldn't* have happened.
Quoted 5 lines
Quoted 2 lines
I guess that means some wdev event is missing? It was the
WARN_ON(current->bss)that fired.Hmm, that's odd, the
process_wdev_events()call is right before that, so I don't see how that could have happened?
Ok. The warning probably happened in earlier kernel, because our module exit was buggy. I fixed that a while ago and I just verified I don't see it without this patch. Sorry for bringing that diversion up.
Actually, this was not the reason for the doing the msleep(). The problem was that wpa_supplicant received RTM_DELLINK, before getting the NL08211_DISCONNECT. This resulted in RTM_DELLINK, immediately followed by RTM_ADDLINK, followed by NL80211_DISCONNECT.
Gr. AvS
Johannes Berg
maintainerRe: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 4 lines · Arend van Spriel
Actually, this was not the reason for the doing the
msleep(). The problem was thatwpa_supplicantreceivedRTM_DELLINK, before getting theNL08211_DISCONNECT. This resulted inRTM_DELLINK, immediately followed byRTM_ADDLINK, followed byNL80211_DISCONNECT.
I'm not sure this isn't still possible? I don't know when DELLINK is sent.
johannes
Re: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 9 lines · Johannes Berg
Quoted 4 lines · Arend van Spriel
Actually, this was not the reason for the doing the
msleep(). The problem was thatwpa_supplicantreceivedRTM_DELLINK, before getting theNL08211_DISCONNECT. This resulted inRTM_DELLINK, immediately followed byRTM_ADDLINK, followed byNL80211_DISCONNECT.I'm not sure this isn't still possible? I don't know when DELLINK is sent.
Given the behaviour I would say before the netdev notifier, which may be considered wrong. It depends whether the notifier was intended for the kind of thing that cfg80211 is doing, ie. send a netlink event to user-space?
Gr. AvS
Johannes Berg
maintainerRe: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 7 lines · Arend van Spriel
Quoted 2 lines
I'm not sure this isn't still possible? I don't know when DELLINK is sent.
Given the behaviour I would say before the netdev notifier, which may be considered wrong. It depends whether the notifier was intended for the kind of thing that cfg80211 is doing, ie. send a netlink event to user-space?
Well, I checked:
call_netdevice_notifiers(NETDEV_UNREGISTER, dev);
if (!dev->rtnl_link_ops ||
dev->rtnl_link_state == RTNL_LINK_INITIALIZED)
rtmsg_ifinfo(RTM_DELLINK, dev, ~0U, GFP_KERNEL);so ... :)
johannes
Re: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 12 lines · Johannes Berg
Quoted 7 lines · Arend van Spriel
Quoted 2 lines
I'm not sure this isn't still possible? I don't know when DELLINK is sent.
Given the behaviour I would say before the netdev notifier, which may be considered wrong. It depends whether the notifier was intended for the kind of thing that cfg80211 is doing, ie. send a netlink event to user-space?
Well, I checked:
Quoted 7 lines
call_netdevice_notifiers(NETDEV_UNREGISTER, dev); if (!dev->rtnl_link_ops || dev->rtnl_link_state == RTNL_LINK_INITIALIZED) rtmsg_ifinfo(RTM_DELLINK, dev, ~0U, GFP_KERNEL);so ... :)
Feeling sad :-( but thanks for checking. Clearly need to look into this some more. John, can you please drop this one.
Gr. AvS
Johannes Berg
maintainerRe: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 2 lines · Arend van Spriel
Feeling sad :-( but thanks for checking. Clearly need to look into this some more. John, can you please drop this one.
I think you probably still want to drop the other sleep?
johannes
Re: [PATCH 01/14] brcmfmac: add delay before unregistering the network device
Quoted 6 lines · Johannes Berg
Quoted 2 lines · Arend van Spriel
Feeling sad :-( but thanks for checking. Clearly need to look into this some more. John, can you please drop this one.
I think you probably still want to drop the other sleep?
Yeah. That one is pretty useless anyway given that it is under rtnl_lock. Just want to check that it works when I remove the sleep between cfg80211_disconnected() and unregister_netdev() as well.
Gr. AvS
PATCH 2/14 brcmfmac: Make firmeware roaming a module param.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
Internal firmware roaming is enabled by default. This patch makes it possible to disable internal firmware roaming by specifying roamoff=1 as module param.
--- .../net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 38 +++++++++++++------- .../net/wireless/brcm80211/brcmfmac/wl_cfg80211.h | 1 - 2 files changed, 25 insertions(+), 14 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c +25 -13
@@ -18,6 +18,7 @@#include <linux/kernel.h> #include <linux/etherdevice.h> +#include <linux/module.h> #include <net/cfg80211.h> #include <net/netlink.h>
@@ -251,6 +252,10 @@ struct parsed_vndr_ies {struct parsed_vndr_ie_info ie_info[VNDR_IE_PARSE_LIMIT ]; }; +static int brcmf_roamoff; +module_param_named (roamoff, brcmf_roamoff, int,S_IRUSR ); +MODULE_PARM_DESC (roamoff,"do not use internal roaming engine" ); +/* Quarter dBm units to mW * Table starts at QDBM_OFFSET, so the first entry is mW for qdBm=153 * Table is offset so the last entry is largest mW value that fits in
@@ -4444,7 +4449,9 @@ static bool brcmf_is_linkdown(const struct brcmf_event_msg *e)u32 event = e->event_code;u16 flags = e->flags; -if (event ==BRCMF_E_LINK && (!(flags &BRCMF_EVENT_MSG_LINK ))) { +if ((event ==BRCMF_E_DEAUTH ) || (event ==BRCMF_E_DEAUTH_IND ) || + (event ==BRCMF_E_DISASSOC_IND ) || + ((event ==BRCMF_E_LINK ) && (!(flags &BRCMF_EVENT_MSG_LINK )))) {brcmf_dbg (CONN ,"Processing link down\n" );return true; }
@@ -4688,6 +4695,7 @@ brcmf_notify_connect_status(struct brcmf_if *ifp,struct brcmf_cfg80211_profile *profile = &ifp->vif->profile;struct ieee80211_channel *chan;s32 err =0 ; +u16 reason;if (ifp->vif->mode ==WL_MODE_AP ) { err =brcmf_notify_connect_status_ap (cfg, ndev, e, data);
@@ -4709,9 +4717,15 @@ brcmf_notify_connect_status(struct brcmf_if *ifp,if (!brcmf_is_ibssmode (ifp->vif)) {brcmf_bss_connect_done (cfg, ndev, e, false);if (test_and_clear_bit (BRCMF_VIF_STATUS_CONNECTED , - &ifp->vif->sme_state)) -cfg80211_disconnected (ndev,0 ,NULL ,0 , + &ifp->vif->sme_state)) { + reason =0 ; +if (((e->event_code ==BRCMF_E_DEAUTH_IND ) || + (e->event_code ==BRCMF_E_DISASSOC_IND )) && + (e->reason !=WLAN_REASON_UNSPECIFIED )) + reason = e->reason; +cfg80211_disconnected (ndev, reason,NULL ,0 ,GFP_KERNEL ); + } }brcmf_link_down (ifp->vif);brcmf_init_prof (ndev_to_prof (ndev));
@@ -4905,11 +4919,8 @@ static s32 wl_init_priv(struct brcmf_cfg80211_info *cfg) cfg->scan_request =NULL ; cfg->pwr_save = true; - cfg->roam_on = true;/* roam on & off switch. -we enable roam per default */ - cfg->active_scan = true;/* we do active scan for -specific scan per default */ - cfg->dongle_up = false;/* dongle is not up yet */ + cfg->active_scan = true;/* we do active scan per default */ + cfg->dongle_up = false;/* dongle is not up yet */ err =brcmf_init_priv_mem (cfg);if (err)return err;
@@ -5029,7 +5040,7 @@ void brcmf_cfg80211_detach(struct brcmf_cfg80211_info *cfg) }static s32 -brcmf_dongle_roam (struct brcmf_if *ifp,u32 roamvar,u32 bcn_timeout) +brcmf_dongle_roam (struct brcmf_if *ifp,u32 bcn_timeout) {s32 err =0 ;__le32 roamtrigger[2 ];
@@ -5039,7 +5050,7 @@ brcmf_dongle_roam(struct brcmf_if *ifp, u32 roamvar, u32 bcn_timeout)* Setup timeout if Beacons are lost and roam is * off to report link down */ -if (roamvar) { +if (brcmf_roamoff) { err =brcmf_fil_iovar_int_set (ifp,"bcn_timeout" , bcn_timeout);if (err) {brcmf_err ("bcn_timeout error (%d)\n" , err);
@@ -5051,8 +5062,9 @@ brcmf_dongle_roam(struct brcmf_if *ifp, u32 roamvar, u32 bcn_timeout)* Enable/Disable built-in roaming to allow supplicant * to take care of roaming */ -brcmf_dbg (INFO ,"Internal Roaming = %s\n" , roamvar ?"Off" :"On" ); - err =brcmf_fil_iovar_int_set (ifp,"roam_off" , roamvar); +brcmf_dbg (INFO ,"Internal Roaming = %s\n" , + brcmf_roamoff ?"Off" :"On" ); + err =brcmf_fil_iovar_int_set (ifp,"roam_off" , !!(brcmf_roamoff));if (err) {brcmf_err ("roam_off error (%d)\n" , err); goto dongle_rom_out;
@@ -5408,7 +5420,7 @@ static s32 brcmf_config_dongle(struct brcmf_cfg80211_info *cfg)brcmf_dbg (INFO ,"power save set to %s\n" , (power_mode ?"enabled" :"disabled" )); - err =brcmf_dongle_roam (ifp, (cfg->roam_on ?0 :1 ),WL_BEACON_TIMEOUT ); + err =brcmf_dongle_roam (ifp,WL_BEACON_TIMEOUT );if (err) goto default_conf_out; err = brcmf_cfg80211_change_iface(wdev->wiphy, ndev, wdev->iftype,
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.h +0 -1
@@ -402,7 +402,6 @@ struct brcmf_cfg80211_info {bool ibss_starter;bool pwr_save;bool dongle_up; -bool roam_on;bool scan_tried;u8 *dcmd_buf;u8 *extra_buf;
Signature · 1 line
1.7.10.4
PATCH 3/14 brcmfmac: fix use of skb control buffer in SDIO driver part
In reply to Arend van SprielThe SDIO driver has a 16-bit field defined in the skbuff control buffer. However, it is accessed as a u32 overwriting other control info. Another issue is that the field is not initialized for networking packets, but the control buffer content is unspecified as other networking layers can use it.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +6 -4
@@ -2112,7 +2112,7 @@ static int brcmf_sdio_txpkt_prep_sg(struct brcmf_sdio *bus,memcpy (pkt_pad->data, pkt->data + pkt->len - tail_chop, tail_chop); - *(u32 *)(pkt_pad->cb) =ALIGN_SKB_FLAG + tail_chop; + *(u16 *)(pkt_pad->cb) =ALIGN_SKB_FLAG + tail_chop;skb_trim (pkt, pkt->len - tail_chop);__skb_queue_after (pktq, pkt, pkt_pad); }else {
@@ -2159,7 +2159,7 @@ brcmf_sdio_txpkt_prep(struct brcmf_sdio *bus, struct sk_buff_head *pktq,* already properly aligned and does not * need an sdpcm header. */ -if (*(u32 *)(pkt_next->cb) &ALIGN_SKB_FLAG ) +if (*(u16 *)(pkt_next->cb) &ALIGN_SKB_FLAG )continue ;/* align packet data pointer */
@@ -2223,11 +2223,11 @@ brcmf_sdio_txpkt_postp(struct brcmf_sdio *bus, struct sk_buff_head *pktq)u8 *hdr;u32 dat_offset;u16 tail_pad; -u32 dummy_flags, chop_len; +u16 dummy_flags, chop_len;struct sk_buff *pkt_next, *tmp, *pkt_prev; skb_queue_walk_safe(pktq, pkt_next, tmp) { - dummy_flags = *(u32 *)(pkt_next->cb); + dummy_flags = *(u16 *)(pkt_next->cb);if (dummy_flags &ALIGN_SKB_FLAG ) { chop_len = dummy_flags &ALIGN_SKB_CHOP_LEN_MASK ;if (chop_len) {
@@ -2709,6 +2709,8 @@ static int brcmf_sdio_bus_txdata(struct device *dev, struct sk_buff *pkt)/* Priority based enq */ spin_lock_irqsave (&bus->txqlock, flags); +/* reset bus_flags in packet cb */ + *(u16 *)(pkt->cb) =0 ;if (!brcmf_c_prec_enq (bus->sdiodev->dev, &bus->txq, pkt, prec)) {skb_pull (pkt, bus->tx_hdrlen);brcmf_err ("out of bus->txq !!!\n" );
Signature · 1 line
1.7.10.4
PATCH 4/14 brcmfmac: remove unused variable data_len from brcmf_sdio_bus_txdata()
In reply to Arend van SprielThe local variable data_len is assigned but never used so get rid of it.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +2 -4
@@ -2686,15 +2686,13 @@ static struct pktq *brcmf_sdio_bus_gettxq(struct device *dev)static int brcmf_sdio_bus_txdata (struct device *dev,struct sk_buff *pkt) {int ret = -EBADE ; -uint datalen, prec; +uint prec;struct brcmf_bus *bus_if =dev_get_drvdata (dev);struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio;struct brcmf_sdio *bus = sdiodev->bus;ulong flags; -brcmf_dbg (TRACE ,"Enter\n" ); - - datalen = pkt->len; +brcmf_dbg (TRACE ,"Enter: pkt: data %p len %d\n" , pkt->data, pkt->len);/* Add space for the header */ skb_push (pkt, bus->tx_hdrlen);
Signature · 1 line
1.7.10.4
PATCH 5/14 brcmfmac: Correct header debug dump for sdio tx hdrs.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +2 -2
@@ -2193,10 +2193,10 @@ brcmf_sdio_txpkt_prep(struct brcmf_sdio *bus, struct sk_buff_head *pktq,if (BRCMF_BYTES_ON () && ((BRCMF_CTL_ON () && chan ==SDPCM_CONTROL_CHANNEL ) || (BRCMF_DATA_ON () && chan !=SDPCM_CONTROL_CHANNEL ))) -brcmf_dbg_hex_dump (true, pkt_next, hd_info.len, +brcmf_dbg_hex_dump (true, pkt_next->data, hd_info.len,"Tx Frame:\n" );else if (BRCMF_HDRS_ON ()) -brcmf_dbg_hex_dump (true, pkt_next, +brcmf_dbg_hex_dump (true, pkt_next->data, head_pad + bus->tx_hdrlen,"Tx Header:\n" ); }
Signature · 1 line
1.7.10.4
PATCH 6/14 brcmfmac: de-init driver layers in correct order.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
First clean up fw signalling, before cleaning up the bus and proto layer. Old order can cause oops in some circumstances.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_linux.c +2 -2
@@ -1044,12 +1044,12 @@ void brcmf_detach(struct device *dev)brcmf_cfg80211_detach (drvr->config); +brcmf_fws_deinit (drvr); +brcmf_bus_detach (drvr);brcmf_proto_detach (drvr); -brcmf_fws_deinit (drvr); -brcmf_debugfs_detach (drvr); bus_if->drvr =NULL ;kfree (drvr);
Signature · 1 line
1.7.10.4
PATCH 7/14 brcmfmac: Minimize SDIO dpc scheduling.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
SDIO dpc scheduling is done (repeated) when counter is set. This counter gets decreased when dpc is finished. It is more efficient to set counter to 0 before the dpc is actullay run. This will minimize the frequency with which dpc is executed.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +1 -1
@@ -3758,8 +3758,8 @@ static void brcmf_sdio_dataworker(struct work_struct *work) datawork);while (atomic_read (&bus->dpc_tskcnt)) { +atomic_set (&bus->dpc_tskcnt,0 );brcmf_sdio_dpc (bus); -atomic_dec (&bus->dpc_tskcnt); } }
Signature · 1 line
1.7.10.4
PATCH 8/14 brcmfmac: Remove immediate sleep support from SDIO.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
Immediate sleep support is an aggressive power saving option that has not been enabled in brcmfmac and is removed to simplify code.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 20 -------------------- 1 file changed, 20 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +0 -20
@@ -304,7 +304,6 @@ struct rte_console {/* Flags for SDH calls */ #define F2SYNC (SDIO_REQ_4BYTE | SDIO_REQ_FIXED) -#define BRCMF_IDLE_IMMEDIATE (-1)/* Enter idle immediately */ #define BRCMF_IDLE_ACTIVE 0/* Do not request any SD clock change * when idle */
@@ -2662,16 +2661,6 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) data_ok(bus)) || PKT_AVAILABLE()) {atomic_inc (&bus->dpc_tskcnt); } - -/* If we're done for now, turn off clock request. */ -if ((bus->clkstate !=CLK_PENDING ) - && bus->idletime ==BRCMF_IDLE_IMMEDIATE ) { - bus->activity = false; -brcmf_dbg (SDIO ,"idle state\n" ); -sdio_claim_host (bus->sdiodev->func[1 ]); -brcmf_sdio_bus_sleep (bus, true, false); -sdio_release_host (bus->sdiodev->func[1 ]); - } }static struct pktq *brcmf_sdio_bus_gettxq (struct device *dev)
@@ -2948,15 +2937,6 @@ brcmf_sdio_bus_txctl(struct device *dev, unsigned char *msg, uint msglen) }while (ret <0 && retries++ <TXRETRIES ); } -if ((bus->idletime ==BRCMF_IDLE_IMMEDIATE ) && -atomic_read (&bus->dpc_tskcnt) ==0 ) { - bus->activity = false; -sdio_claim_host (bus->sdiodev->func[1 ]); -brcmf_dbg (INFO ,"idle\n" ); -brcmf_sdio_clkctl (bus,CLK_NONE , true); -sdio_release_host (bus->sdiodev->func[1 ]); - } -if (ret) bus->sdcnt.tx_ctlerrs++;else
Signature · 1 line
1.7.10.4
PATCH 9/14 brcmfmac: Small cleanup of redundant code.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
In time some of the code got redundant, without being noticed. This patch does not change any functionality, just removes redundant code.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 18 ++++++------------ 1 file changed, 6 insertions(+), 12 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +6 -12
@@ -770,8 +770,6 @@ brcmf_sdio_kso_control(struct brcmf_sdio *bus, bool on)return err; } -#define PKT_AVAILABLE () (intstatus & I_HMB_FRAME_IND) -#define HOSTINTMASK (I_HMB_SW_MASK | I_CHIPACTIVE)/* Turn backplane clock on or off */
@@ -870,7 +868,6 @@ static int brcmf_sdio_htclk(struct brcmf_sdio *bus, bool on, bool pendok) }#endif /* defined (DEBUG) */ - bus->activity = true; }else { clkreq =0 ;
@@ -2341,7 +2338,7 @@ static uint brcmf_sdio_sendfromq(struct brcmf_sdio *bus, uint maxframes) cnt += i;/* In poll mode, need to check for other events */ -if (!bus->intr && cnt) { +if (!bus->intr) {/* Check device status, signal pending interrupt */ sdio_claim_host (bus->sdiodev->func[1 ]); ret = r_sdreg32(bus, &intstatus,
@@ -2485,9 +2482,8 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) {u32 newstatus =0 ;unsigned long intstatus; -uint rxlimit = bus->rxbound;/* Rx frames to read before resched */ uint txlimit = bus->txbound;/* Tx frames to send before resched */ -uint framecnt =0 ;/* Temporary counter of tx/rx frames */ +uint framecnt;/* Temporary counter of tx/rx frames */ int err =0 , n;brcmf_dbg (TRACE ,"Enter\n" );
@@ -2585,11 +2581,10 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) intstatus &= ~I_HMB_FRAME_IND ;/* On frame indication, read available frames */ -if (PKT_AVAILABLE () && bus->clkstate ==CLK_AVAIL ) { - framecnt =brcmf_sdio_readframes (bus, rxlimit); +if ((intstatus &I_HMB_FRAME_IND ) && (bus->clkstate ==CLK_AVAIL )) { +brcmf_sdio_readframes (bus, bus->rxbound);if (!bus->rxpending) intstatus &= ~I_HMB_FRAME_IND ; - rxlimit -=min (framecnt, rxlimit); }/* Keep still-pending events for next scheduling */
@@ -2647,8 +2642,7 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) && data_ok(bus)) { framecnt = bus->rxpending ?min (txlimit, bus->txminmax) : txlimit; - framecnt =brcmf_sdio_sendfromq (bus, framecnt); - txlimit -= framecnt; +brcmf_sdio_sendfromq (bus, framecnt); }if (!brcmf_bus_ready (bus->sdiodev->bus_if) || (err !=0 )) {
@@ -2658,7 +2652,7 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) atomic_read(&bus->ipend) > 0 || (!atomic_read(&bus->fcstate) && brcmu_pktq_mlen(&bus->txq, ~bus->flowcontrol) && - data_ok(bus)) || PKT_AVAILABLE()) { + data_ok(bus))) {atomic_inc (&bus->dpc_tskcnt); } }
Signature · 1 line
1.7.10.4
PATCH 10/14 brcmfmac: Use atomic functions for intstatus update.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
The intstatus in sdio code can be updated from different threads. To protect intstatus access, atomic functions are used. One of them is set_bit, but this function is not guaranteed atomic on all platforms. The loop was replaced with local created OR function.
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 29 ++++++++++---------- 1 file changed, 15 insertions(+), 14 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +15 -14
@@ -2444,12 +2444,21 @@ static inline void brcmf_sdio_clrintr(struct brcmf_sdio *bus) } } +static void atomic_orr (int val,atomic_t *v) +{ +int old_val; + + old_val =atomic_read (v); +while (atomic_cmpxchg (v, old_val, val | old_val) != old_val) + old_val =atomic_read (v); +} +static int brcmf_sdio_intr_rstatus (struct brcmf_sdio *bus) {struct brcmf_core *buscore;u32 addr;unsigned long val; -int n, ret; +int ret; buscore =brcmf_chip_get_core (bus->ci,BCMA_CORE_SDIO_DEV ); addr = buscore->base + offsetof(struct sdpcmd_regs , intstatus);
@@ -2457,7 +2466,7 @@ static int brcmf_sdio_intr_rstatus(struct brcmf_sdio *bus) val =brcmf_sdiod_regrl (bus->sdiodev, addr, &ret); bus->sdcnt.f1regdata++;if (ret !=0 ) - val =0 ; +return ret; val &= bus->hostintmask;atomic_set (&bus->fcstate, !!(val &I_HMB_FC_STATE ));
@@ -2466,13 +2475,7 @@ static int brcmf_sdio_intr_rstatus(struct brcmf_sdio *bus)if (val) {brcmf_sdiod_regwl (bus->sdiodev, addr, val, &ret); bus->sdcnt.f1regdata++; - } - -if (ret) { -atomic_set (&bus->intstatus,0 ); - }else if (val) { -for_each_set_bit (n, &val,32 ) -set_bit (n, (unsigned long *)&bus->intstatus.counter); +atomic_orr (val, &bus->intstatus); }return ret;
@@ -2484,7 +2487,7 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus)unsigned long intstatus;uint txlimit = bus->txbound;/* Tx frames to send before resched */ uint framecnt;/* Temporary counter of tx/rx frames */ -int err =0 , n; +int err =0 ;brcmf_dbg (TRACE ,"Enter\n" );
@@ -2588,10 +2591,8 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) }/* Keep still-pending events for next scheduling */ -if (intstatus) { -for_each_set_bit (n, &intstatus,32 ) -set_bit (n, (unsigned long *)&bus->intstatus.counter); - } +if (intstatus) +atomic_orr (intstatus, &bus->intstatus);brcmf_sdio_clrintr (bus);
Signature · 1 line
1.7.10.4
Re: [PATCH 10/14] brcmfmac: Use atomic functions for intstatus update.
Hi Arend,
2014-02-25 11:30 GMT-08:00 Arend van Spriel <[email protected]>:
Quoted 24 lines
From: Hante Meuleman <[email protected]>
The intstatus in sdio code can be updated from different threads. To protect intstatus access, atomic functions are used. One of them is
set_bit, but this function is not guaranteed atomic on all platforms. The loop was replaced with local created OR function.Reviewed-by Arend Van Spriel <[email protected]>Reviewed-by Franky (Zhenhui) Lin <[email protected]>Reviewed-by Pieter-Paul Giesberts <[email protected]>Reviewed-by Daniel (Deognyoun) Kim <[email protected]>Signed-off-by Hante Meuleman <[email protected]>Signed-off-by Arend van Spriel <[email protected]>--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 29 ++++++++++---------- 1 file changed, 15 insertions(+), 14 deletions(-)drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +0
-0@@ -2444,12 +2444,21 @@ static inline void brcmf_sdio_clrintr(struct brcmf_sdio *bus) }
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c static inline void brcmf_sdio_clrintr(struct brcmf_sdio *bus) · line 2454
Quoted 10 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +8
-0} +static void atomic_orr (int val,atomic_t *v) +{ +int old_val; + + old_val =atomic_read (v); +while (atomic_cmpxchg (v, old_val, val | old_val) != old_val) + old_val =atomic_read (v); +}
Is not atomic_set_mask() doing the same thing?
Quoted 64 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +7
-15+static int brcmf_sdio_intr_rstatus (struct brcmf_sdio *bus) {struct brcmf_core *buscore;u32 addr;unsigned long val; -int n, ret; +int ret; buscore =brcmf_chip_get_core (bus->ci,BCMA_CORE_SDIO_DEV ); addr = buscore->base + offsetof(struct sdpcmd_regs , intstatus);@@ -2457,7 +2466,7 @@ static int brcmf_sdio_intr_rstatus(struct brcmf_sdio *bus) val =brcmf_sdiod_regrl (bus->sdiodev, addr, &ret); bus->sdcnt.f1regdata++;if (ret !=0 ) - val =0 ; +return ret; val &= bus->hostintmask;atomic_set (&bus->fcstate, !!(val &I_HMB_FC_STATE ));@@ -2466,13 +2475,7 @@ static int brcmf_sdio_intr_rstatus(struct brcmf_sdio *bus)if (val) {brcmf_sdiod_regwl (bus->sdiodev, addr, val, &ret); bus->sdcnt.f1regdata++; - } - -if (ret) { -atomic_set (&bus->intstatus,0 ); - }else if (val) { -for_each_set_bit (n, &val,32 ) -set_bit (n, (unsigned long *)&bus->intstatus.counter); +atomic_orr (val, &bus->intstatus); }return ret;@@ -2484,7 +2487,7 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus)unsigned long intstatus;uint txlimit = bus->txbound;/* Tx frames to send before resched */ uint framecnt;/* Temporary counter of tx/rx frames */ -int err =0 , n; +int err =0 ;brcmf_dbg (TRACE ,"Enter\n" );@@ -2588,10 +2591,8 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus) }/* Keep still-pending events for next scheduling */ -if (intstatus) { -for_each_set_bit (n, &intstatus,32 ) -set_bit (n, (unsigned long *)&bus->intstatus.counter); - } +if (intstatus) +atomic_orr (intstatus, &bus->intstatus);brcmf_sdio_clrintr (bus); --1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 1 line
Florian
Re: [PATCH 10/14] brcmfmac: Use atomic functions for intstatus update.
Quoted 29 lines · Florian Fainelli
Hi Arend,
2014-02-25 11:30 GMT-08:00 Arend van Spriel <[email protected]>:
Quoted 26 lines
From: Hante Meuleman <[email protected]>
The intstatus in sdio code can be updated from different threads. To protect intstatus access, atomic functions are used. One of them is
set_bit, but this function is not guaranteed atomic on all platforms. The loop was replaced with local created OR function.Reviewed-by Arend Van Spriel <[email protected]>Reviewed-by Franky (Zhenhui) Lin <[email protected]>Reviewed-by Pieter-Paul Giesberts <[email protected]>Reviewed-by Daniel (Deognyoun) Kim <[email protected]>Signed-off-by Hante Meuleman <[email protected]>Signed-off-by Arend van Spriel <[email protected]>--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 29 ++++++++++---------- 1 file changed, 15 insertions(+), 14 deletions(-)drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +0
-0@@ -2444,12 +2444,21 @@ static inline void brcmf_sdio_clrintr(struct brcmf_sdio *bus) } }
Quoted 10 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c static inline void brcmf_sdio_clrintr(struct brcmf_sdio *bus) · line 2454
Quoted 8 lines
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +8
-0+static void atomic_orr (int val,atomic_t *v) +{ +int old_val; + + old_val =atomic_read (v); +while (atomic_cmpxchg (v, old_val, val | old_val) != old_val) + old_val =atomic_read (v); +}Is not
atomic_set_mask()doing the same thing?
You are right. Hante thought that one was not supported on all archs, but asm-generic provides a fallback for those. I will revise this patch.
Thanks,
Arend
PATCH 11/14 brcmfmac: Put frame sdio tx error handling in sub function.
In reply to Arend van SprielFrom: Hante Meuleman <[email protected]>
--- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 112 ++++++-------------- 1 file changed, 33 insertions(+), 79 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +33 -79
@@ -1237,6 +1237,28 @@ static void brcmf_sdio_rxfail(struct brcmf_sdio *bus, bool abort, bool rtx) bus->cur_read.len =0 ; } +static void brcmf_sdio_txfail (struct brcmf_sdio *bus) +{ +struct brcmf_sdio_dev *sdiodev = bus->sdiodev; +u8 i, hi, lo; + +/* On failure, abort the command and terminate the frame */ +brcmf_err ("sdio error, abort command and terminate frame\n" ); + bus->sdcnt.tx_sderrs++; + +brcmf_sdiod_abort (sdiodev,SDIO_FUNC_2 ); +brcmf_sdiod_regwb (sdiodev,SBSDIO_FUNC1_FRAMECTRL ,SFC_WF_TERM ,NULL ); + bus->sdcnt.f1regdata++; + +for (i =0 ; i <3 ; i++) { + hi =brcmf_sdiod_regrb (sdiodev,SBSDIO_FUNC1_WFRAMEBCHI ,NULL ); + lo =brcmf_sdiod_regrb (sdiodev,SBSDIO_FUNC1_WFRAMEBCLO ,NULL ); + bus->sdcnt.f1regdata +=2 ; +if ((hi ==0 ) && (lo ==0 )) +break ; + } +} +/* return total length of buffer chain */ static uint brcmf_sdio_glom_len (struct brcmf_sdio *bus) {
@@ -2252,7 +2274,6 @@ static int brcmf_sdio_txpkt(struct brcmf_sdio *bus, struct sk_buff_head *pktq, uint chan) {int ret; -int i;struct sk_buff *pkt_next, *tmp;brcmf_dbg (TRACE ,"Enter\n" );
@@ -2265,28 +2286,9 @@ static int brcmf_sdio_txpkt(struct brcmf_sdio *bus, struct sk_buff_head *pktq, ret =brcmf_sdiod_send_pkt (bus->sdiodev, pktq); bus->sdcnt.f2txdata++; -if (ret <0 ) { -/* On failure, abort the command and terminate the frame */ -brcmf_dbg (INFO ,"sdio error %d, abort command and terminate frame\n" , - ret); - bus->sdcnt.tx_sderrs++; +if (ret <0 ) +brcmf_sdio_txfail (bus); -brcmf_sdiod_abort (bus->sdiodev,SDIO_FUNC_2 ); -brcmf_sdiod_regwb (bus->sdiodev,SBSDIO_FUNC1_FRAMECTRL , -SFC_WF_TERM ,NULL ); - bus->sdcnt.f1regdata++; - -for (i =0 ; i <3 ; i++) { -u8 hi, lo; - hi =brcmf_sdiod_regrb (bus->sdiodev, -SBSDIO_FUNC1_WFRAMEBCHI ,NULL ); - lo =brcmf_sdiod_regrb (bus->sdiodev, -SBSDIO_FUNC1_WFRAMEBCLO ,NULL ); - bus->sdcnt.f1regdata +=2 ; -if ((hi ==0 ) && (lo ==0 )) -break ; - } - }sdio_release_host (bus->sdiodev->func[1 ]); done:
@@ -2597,42 +2599,17 @@ static void brcmf_sdio_dpc(struct brcmf_sdio *bus)brcmf_sdio_clrintr (bus);if (data_ok (bus) && bus->ctrl_frame_stat && - (bus->clkstate ==CLK_AVAIL )) { -int i; + (bus->clkstate ==CLK_AVAIL )) {sdio_claim_host (bus->sdiodev->func[1 ]); err =brcmf_sdiod_send_buf (bus->sdiodev, bus->ctrl_frame_buf, (u32 )bus->ctrl_frame_len); -if (err <0 ) { -/* On failure, abort the command and -terminate the frame */ -brcmf_dbg (INFO ,"sdio error %d, abort command and terminate frame\n" , - err); - bus->sdcnt.tx_sderrs++; - -brcmf_sdiod_abort (bus->sdiodev,SDIO_FUNC_2 ); - -brcmf_sdiod_regwb (bus->sdiodev,SBSDIO_FUNC1_FRAMECTRL , -SFC_WF_TERM , &err); - bus->sdcnt.f1regdata++; - -for (i =0 ; i <3 ; i++) { -u8 hi, lo; - hi =brcmf_sdiod_regrb (bus->sdiodev, -SBSDIO_FUNC1_WFRAMEBCHI , - &err); - lo =brcmf_sdiod_regrb (bus->sdiodev, -SBSDIO_FUNC1_WFRAMEBCLO , - &err); - bus->sdcnt.f1regdata +=2 ; -if ((hi ==0 ) && (lo ==0 )) -break ; - } - - }else { +if (err <0 ) +brcmf_sdio_txfail (bus); +else bus->tx_seq = (bus->tx_seq +1 ) %SDPCM_SEQ_WRAP ; - } +sdio_release_host (bus->sdiodev->func[1 ]); bus->ctrl_frame_stat = false;brcmf_sdio_wait_event_wakeup (bus);
@@ -2802,38 +2779,15 @@ break2:static int brcmf_sdio_tx_frame (struct brcmf_sdio *bus,u8 *frame,u16 len) { -int i;int ret; bus->ctrl_frame_stat = false; ret =brcmf_sdiod_send_buf (bus->sdiodev, frame, len); -if (ret <0 ) { -/* On failure, abort the command and terminate the frame */ -brcmf_dbg (INFO ,"sdio error %d, abort command and terminate frame\n" , - ret); - bus->sdcnt.tx_sderrs++; - -brcmf_sdiod_abort (bus->sdiodev,SDIO_FUNC_2 ); - -brcmf_sdiod_regwb (bus->sdiodev,SBSDIO_FUNC1_FRAMECTRL , -SFC_WF_TERM ,NULL ); - bus->sdcnt.f1regdata++; - -for (i =0 ; i <3 ; i++) { -u8 hi, lo; - hi =brcmf_sdiod_regrb (bus->sdiodev, -SBSDIO_FUNC1_WFRAMEBCHI ,NULL ); - lo =brcmf_sdiod_regrb (bus->sdiodev, -SBSDIO_FUNC1_WFRAMEBCLO ,NULL ); - bus->sdcnt.f1regdata +=2 ; -if (hi ==0 && lo ==0 ) -break ; - } -return ret; - } - - bus->tx_seq = (bus->tx_seq +1 ) %SDPCM_SEQ_WRAP ; +if (ret <0 ) +brcmf_sdio_txfail (bus); +else + bus->tx_seq = (bus->tx_seq +1 ) %SDPCM_SEQ_WRAP ;return ret; }
Signature · 1 line
1.7.10.4
PATCH 12/14 brcmfmac: Correct mcs index report
In reply to Arend van SprielFrom: Daniel Kim <[email protected]>
There is a mismatch between the mcs index(0-7) reported to cfg80211 and the actual mcs index(0-15) in use. This patch resolves the mismatch by setting mcs info with the number of chains read from FW.
--- drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c | 17 +++++++++++++---- 1 file changed, 13 insertions(+), 4 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c +13 -4
@@ -5306,6 +5306,8 @@ static s32 brcmf_update_wiphybands(struct brcmf_cfg80211_info *cfg)u32 band_list[3 ];u32 nmode;u32 bw_cap[2 ] = {0 ,0 }; +u32 rxchain; +u32 nchain;s8 phy;s32 err;u32 nband;
@@ -5342,6 +5344,16 @@ static s32 brcmf_update_wiphybands(struct brcmf_cfg80211_info *cfg)brcmf_dbg (INFO ,"nmode=%d, bw_cap=(%d, %d)\n" , nmode, bw_cap[IEEE80211_BAND_2GHZ ], bw_cap[IEEE80211_BAND_5GHZ ]); + err =brcmf_fil_iovar_int_get (ifp,"rxchain" , &rxchain); +if (err) { +brcmf_err ("rxchain error (%d)\n" , err); + nchain =1 ; + }else { +for (nchain =0 ; rxchain; nchain++) + rxchain = rxchain & (rxchain -1 ); + } +brcmf_dbg (INFO ,"nchain=%d\n" , nchain); + err =brcmf_construct_reginfo (cfg, bw_cap);if (err) {brcmf_err ("brcmf_construct_reginfo failed (%d)\n" , err);
@@ -5370,10 +5382,7 @@ static s32 brcmf_update_wiphybands(struct brcmf_cfg80211_info *cfg) band->ht_cap.ht_supported = true; band->ht_cap.ampdu_factor =IEEE80211_HT_MAX_AMPDU_64K ; band->ht_cap.ampdu_density =IEEE80211_HT_MPDU_DENSITY_16 ; -/* An HT shall support all EQM rates for one spatial -* stream -*/ - band->ht_cap.mcs.rx_mask[0 ] =0xff ; +memset (band->ht_cap.mcs.rx_mask,0xff , nchain); band->ht_cap.mcs.tx_params =IEEE80211_HT_MCS_TX_DEFINED ; bands[band->band] = band; }
Signature · 1 line
1.7.10.4
PATCH 13/14 brcmfmac: use pre-allocated scatter-gather table for txglomming
In reply to Arend van SprielInstead of allocating a scatter-gather table for every transmit reuse a pre-allocated table. The transmit path will be faster by taking out this allocation.
--- drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 45 ++++++++++++++++---- drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c | 8 +--- .../net/wireless/brcm80211/brcmfmac/sdio_host.h | 2 + 3 files changed, 39 insertions(+), 16 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c +36 -9
@@ -53,6 +53,12 @@/* Maximum milliseconds to wait for F2 to come up */ #define SDIO_WAIT_F2RDY 3000 +#define BRCMF_DEFAULT_TXGLOM_SIZE 32/* max tx frames in glom chain */ +#define BRCMF_DEFAULT_RXGLOM_SIZE 32/* max rx frames in glom chain */ + +static int brcmf_sdiod_txglomsz =BRCMF_DEFAULT_TXGLOM_SIZE ; +module_param_named (txglomsz, brcmf_sdiod_txglomsz, int,0 ); +MODULE_PARM_DESC (txglomsz,"maximum tx packet chain size [SDIO]" );static irqreturn_t brcmf_sdiod_oob_irqhandler (int irq,void *dev_id) {
@@ -487,7 +493,6 @@ static int brcmf_sdiod_sglist_rw(struct brcmf_sdio_dev *sdiodev, uint fn,struct mmc_request mmc_req;struct mmc_command mmc_cmd;struct mmc_data mmc_dat; -struct sg_table st;struct scatterlist *sgl;int ret =0 ;
@@ -532,16 +537,11 @@ static int brcmf_sdiod_sglist_rw(struct brcmf_sdio_dev *sdiodev, uint fn, pkt_offset =0 ; pkt_next = target_list->next; -if (sg_alloc_table (&st, max_seg_cnt,GFP_KERNEL )) { - ret = -ENOMEM ; - goto exit; - } -memset (&mmc_req,0 ,sizeof (struct mmc_request ));memset (&mmc_cmd,0 ,sizeof (struct mmc_command ));memset (&mmc_dat,0 ,sizeof (struct mmc_data )); - mmc_dat.sg = st.sgl; + mmc_dat.sg = sdiodev->sgtable.sgl; mmc_dat.blksz = func_blk_sz; mmc_dat.flags = write ?MMC_DATA_WRITE :MMC_DATA_READ ; mmc_cmd.opcode =SD_IO_RW_EXTENDED ;
@@ -557,7 +557,7 @@ static int brcmf_sdiod_sglist_rw(struct brcmf_sdio_dev *sdiodev, uint fn,while (seg_sz) { req_sz =0 ; sg_cnt =0 ; - sgl = st.sgl; + sgl = sdiodev->sgtable.sgl;/* prep sg table */ while (pkt_next != (struct sk_buff *)target_list) { pkt_data = pkt_next->data + pkt_offset;
@@ -639,7 +639,7 @@ static int brcmf_sdiod_sglist_rw(struct brcmf_sdio_dev *sdiodev, uint fn, } exit: -sg_free_table (&st); +sg_init_table (sdiodev->sgtable.sgl, sdiodev->sgtable.orig_nents);while ((pkt_next =__skb_dequeue (&local_list)) !=NULL )brcmu_pkt_buf_free_skb (pkt_next);
@@ -863,6 +863,27 @@ int brcmf_sdiod_abort(struct brcmf_sdio_dev *sdiodev, uint fn)return 0 ; } +static void brcmf_sdiod_sgtable_alloc (struct brcmf_sdio_dev *sdiodev) +{ +uint nents; +int err; + +if (!sdiodev->sg_support) +return ; + + nents =max_t (uint,BRCMF_DEFAULT_RXGLOM_SIZE , brcmf_sdiod_txglomsz); + nents += (nents >>4 ) +1 ; + +WARN_ON (nents > sdiodev->max_segment_count); + +brcmf_dbg (TRACE ,"nents=%d\n" , nents); + err =sg_alloc_table (&sdiodev->sgtable, nents,GFP_KERNEL ); +if (err <0 ) { +brcmf_err ("allocation failed: disable scatter-gather" ); + sdiodev->sg_support = false; + } +} +static int brcmf_sdiod_remove (struct brcmf_sdio_dev *sdiodev) {if (sdiodev->bus) {
@@ -880,6 +901,7 @@ static int brcmf_sdiod_remove(struct brcmf_sdio_dev *sdiodev)sdio_disable_func (sdiodev->func[1 ]);sdio_release_host (sdiodev->func[1 ]); +sg_free_table (&sdiodev->sgtable); sdiodev->sbwad =0 ;return 0 ;
@@ -935,6 +957,11 @@ static int brcmf_sdiod_probe(struct brcmf_sdio_dev *sdiodev) SG_MAX_SINGLE_ALLOC); sdiodev->max_segment_size = host->max_seg_size; +/* allocate scatter-gather table. sg support +* will be disabled upon allocation failure. +*/ +brcmf_sdiod_sgtable_alloc (sdiodev); +/* try to attach to the target device */ sdiodev->bus =brcmf_sdio_probe (sdiodev);if (!sdiodev->bus) {
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c +1 -7
@@ -113,8 +113,6 @@ struct rte_console {#define BRCMF_TXBOUND 20/* Default for max tx frames in one scheduling */ -#define BRCMF_DEFAULT_TXGLOM_SIZE 32/* max tx frames in glom chain */ -#define BRCMF_TXMINMAX 1/* Max tx frames if rx still pending */ #define MEMBLOCK 2048/* Block size used for downloading
@@ -511,10 +509,6 @@ static const uint max_roundup = 512;#define ALIGNMENT 4 -static int brcmf_sdio_txglomsz =BRCMF_DEFAULT_TXGLOM_SIZE ; -module_param_named (txglomsz, brcmf_sdio_txglomsz, int,0 ); -MODULE_PARM_DESC (txglomsz,"maximum tx packet chain size [SDIO]" ); -enum brcmf_sdio_frmtype {BRCMF_SDIO_FT_NORMAL ,BRCMF_SDIO_FT_SUPER ,
@@ -2321,7 +2315,7 @@ static uint brcmf_sdio_sendfromq(struct brcmf_sdio *bus, uint maxframes)__skb_queue_head_init (&pktq);if (bus->txglom) pkt_num =min_t (u8, bus->tx_max - bus->tx_seq, - brcmf_sdio_txglomsz); + bus->sdiodev->txglomsz); pkt_num =min_t (u32, pkt_num,brcmu_pktq_mlen (&bus->txq, ~bus->flowcontrol));spin_lock_bh (&bus->txqlock);
drivers/net/wireless/brcm80211/brcmfmac/sdio_host.h +2 -0
@@ -180,6 +180,8 @@ struct brcmf_sdio_dev {uint max_request_size;ushort max_segment_count;uint max_segment_size; +uint txglomsz; +struct sg_table sgtable; };/* sdio core registers */
Signature · 1 line
1.7.10.4
PATCH 14/14 brcmfmac: reset suspend flag upon sdio suspend failure
In reply to Arend van SprielThe suspend callback first sets the suspend flag used in the driver but after that the actual suspend is done, which may fail. Reset the flag upon suspend failure.
--- drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-)
drivers/net/wireless/brcm80211/brcmfmac/bcmsdh.c +5 -3
@@ -1099,9 +1099,7 @@ static int brcmf_ops_sdio_suspend(struct device *dev)struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio;int ret =0 ; -brcmf_dbg (SDIO ,"\n" ); - -atomic_set (&sdiodev->suspend, true); +brcmf_dbg (SDIO ,"Enter\n" ); sdio_flags =sdio_get_host_pm_caps (sdiodev->func[1 ]);if (!(sdio_flags &MMC_PM_KEEP_POWER )) {
@@ -1109,9 +1107,12 @@ static int brcmf_ops_sdio_suspend(struct device *dev)return -EINVAL ; } +atomic_set (&sdiodev->suspend, true); + ret =sdio_set_host_pm_flags (sdiodev->func[1 ],MMC_PM_KEEP_POWER );if (ret) {brcmf_err ("Failed to set pm_flags\n" ); +atomic_set (&sdiodev->suspend, false);return ret; }
@@ -1125,6 +1126,7 @@ static int brcmf_ops_sdio_resume(struct device *dev)struct brcmf_bus *bus_if =dev_get_drvdata (dev);struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio; +brcmf_dbg (SDIO ,"Enter\n" );brcmf_sdio_wd_timer (sdiodev->bus,BRCMF_WD_POLL_MS );atomic_set (&sdiodev->suspend, false);return 0 ;
Signature · 1 line
1.7.10.4