ARM: tegra: Overhaul Venice2 regulators
Subsystems (2)
PATCH v2 1/7 ARM: tegra: Overhaul Venice2 regulators
From: Thierry Reding <[email protected]>
Some of the regulators and the relationships to other regulators are wrong. This commit attempts to rectify this by making them more similar to what the schematics contain. This starts by adding a +VDD_MUX supply that represents the 12V input and derives the main +3.3V_SYS and +5V_SYS supplies from that. The majority of the other regulators derive from one of those three.
While at it, rename the regulators to match the names in the schematics to make them easier to match up.
---
Changes in v2:
- rename as3722_sd2 label to vdd_1v35_lp0 and as3722_sd5 label to vddio_1v8
- rename sd0 regulator from +VDD_CPU to +VDD_CPU_AP to match schematics
- rename sd6 regulator from +VDD_GPU to +VDD_GPU_AP to match schematics
- change polarity of GPIO K.01 from low to high for regulator +5V_VDD_TS_SW
- rename +3.3V_AVDD_HDMI regulator to +3.3V_AVDD_HDMI_AP_GATED
- make +3.3V_RUN regulator controlled by PMU_REGEN3
- add +3.3V_LP0 regulator (controlled by PMU_REGEN1), marking it as always on because it supplies the USB VBUS pins and we don't have a supply input for those yet
arch/arm/boot/dts/tegra124-venice2.dts | 169 +++++++++++++++++++-------------- 1 file changed, 98 insertions(+), 71 deletions(-)
arch/arm/boot/dts/tegra124-venice2.dts +98 -71
@@ -644,19 +644,19 @@ }; regulators { - vsup-sd2-supply = <&vdd_ac_bat_reg>; - vsup-sd3-supply = <&vdd_ac_bat_reg>; - vsup-sd4-supply = <&vdd_ac_bat_reg>; - vsup-sd5-supply = <&vdd_ac_bat_reg>; - vin-ldo0-supply = <&as3722_sd2>; - vin-ldo1-6-supply = <&vdd_ac_bat_reg>; - vin-ldo2-5-7-supply = <&as3722_sd5>; - vin-ldo3-4-supply = <&vdd_ac_bat_reg>; - vin-ldo9-10-supply = <&vdd_ac_bat_reg>; - vin-ldo11-supply = <&vdd_ac_bat_reg>; + vsup-sd2-supply = <&vdd_5v0_sys>; + vsup-sd3-supply = <&vdd_5v0_sys>; + vsup-sd4-supply = <&vdd_5v0_sys>; + vsup-sd5-supply = <&vdd_5v0_sys>; + vin-ldo0-supply = <&vdd_1v35_lp0>; + vin-ldo1-6-supply = <&vdd_3v3_run>; + vin-ldo2-5-7-supply = <&vddio_1v8>; + vin-ldo3-4-supply = <&vdd_3v3_sys>; + vin-ldo9-10-supply = <&vdd_5v0_sys>; + vin-ldo11-supply = <&vdd_3v3_run>; sd0 { - regulator-name = "vdd-cpu"; + regulator-name = "+VDD_CPU_AP"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1400000>; regulator-min-microamp = <3500000>;
@@ -667,7 +667,7 @@ }; sd1 { - regulator-name = "vdd-core"; + regulator-name = "+VDD_CORE"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1350000>; regulator-min-microamp = <2500000>;
@@ -677,8 +677,8 @@ ams,external-control = <1>; }; - as3722_sd2: sd2 { - regulator-name = "vddio-ddr"; + vdd_1v35_lp0: sd2 { + regulator-name = "+1.35V_LP0"; regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; regulator-always-on;
@@ -686,7 +686,7 @@ }; sd3 { - regulator-name = "vddio-ddr-2phase"; + regulator-name = "+1.35V_LP0"; regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; regulator-always-on;
@@ -694,15 +694,15 @@ }; sd4 { - regulator-name = "avdd-pex-sata"; + regulator-name = "+1.05V_RUN"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; regulator-boot-on; regulator-always-on; }; - as3722_sd5: sd5 { - regulator-name = "vddio-sys"; + vddio_1v8: sd5 { + regulator-name = "+1.8V_VDDIO"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on;
@@ -710,7 +710,7 @@ }; sd6 { - regulator-name = "vdd-gpu"; + regulator-name = "+VDD_GPU_AP"; regulator-min-microvolt = <650000>; regulator-max-microvolt = <1200000>; regulator-min-microamp = <3500000>;
@@ -720,7 +720,7 @@ }; ldo0 { - regulator-name = "avdd_pll"; + regulator-name = "+1.05V_RUN_AVDD"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; regulator-boot-on;
@@ -729,13 +729,13 @@ }; ldo1 { - regulator-name = "run-cam-1.8"; + regulator-name = "+1.8V_RUN_CAM"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; ldo2 { - regulator-name = "gen-avdd,vddio-hsic"; + regulator-name = "+1.2V_GEN_AVDD"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-boot-on;
@@ -743,7 +743,7 @@ }; ldo3 { - regulator-name = "vdd-rtc"; + regulator-name = "+1.00V_LP0_VDD_RTC"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; regulator-boot-on;
@@ -752,21 +752,19 @@ }; ldo4 { - regulator-name = "vdd-cam"; + regulator-name = "+3.3V_RUN_CAM"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - regulator-boot-on; - regulator-always-on; }; ldo5 { - regulator-name = "vdd-cam-front"; + regulator-name = "+1.2V_RUN_CAM_FRONT"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; ldo6 { - regulator-name = "vddio-sdmmc3"; + regulator-name = "+VDDIO_SDMMC3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on;
@@ -774,25 +772,25 @@ }; ldo7 { - regulator-name = "vdd-cam-rear"; + regulator-name = "+1.05V_RUN_CAM_REAR"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; }; ldo9 { - regulator-name = "vdd-touch"; + regulator-name = "+2.8V_RUN_TOUCH"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; ldo10 { - regulator-name = "vdd-cam-af"; + regulator-name = "+2.8V_RUN_CAM_AF"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; ldo11 { - regulator-name = "vpp-fuse"; + regulator-name = "+1.8V_RUN_VPP_FUSE"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; };
@@ -975,99 +973,128 @@ #address-cells = <1>; #size-cells = <0>; - vdd_ac_bat_reg: regulator@0 { + vdd_mux: regulator@0 { compatible = "regulator-fixed"; reg = <0>; - regulator-name = "vdd_ac_bat"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; + regulator-name = "+VDD_MUX"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; regulator-always-on; + regulator-boot-on; }; - vdd_3v3_reg: regulator@1 { + vdd_5v0_sys: regulator@1 { compatible = "regulator-fixed"; reg = <1>; - regulator-name = "vdd_3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; + regulator-name = "+5V_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; regulator-always-on; regulator-boot-on; - enable-active-high; - gpio = <&as3722 1 GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_mux>; }; - vdd_3v3_modem_reg: regulator@2 { + vdd_3v3_sys: regulator@2 { compatible = "regulator-fixed"; reg = <2>; - regulator-name = "vdd-modem-3v3"; + regulator-name = "+3.3V_SYS"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - enable-active-high; - gpio = <&as3722 2 GPIO_ACTIVE_HIGH>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; }; - vdd_hdmi_5v0_reg: regulator@3 { + vdd_3v3_run: regulator@3 { compatible = "regulator-fixed"; reg = <3>; - regulator-name = "vdd-hdmi-5v0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; + regulator-name = "+3.3V_RUN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&as3722 1 GPIO_ACTIVE_HIGH>; enable-active-high; - gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_3v3_sys>; }; - vdd_bl_reg: regulator@4 { + vdd_3v3_hdmi: regulator@4 { compatible = "regulator-fixed"; reg = <4>; - regulator-name = "vdd-bl"; + regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_LOW>; + vin-supply = <&vdd_3v3_run>; }; - vdd_ts_sw_5v0: regulator@5 { + vdd_led: regulator@5 { compatible = "regulator-fixed"; reg = <5>; - regulator-name = "vdd_ts_sw"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; + regulator-name = "+VDD_LED"; + gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>; enable-active-high; - regulator-boot-on; - gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_LOW>; + vin-supply = <&vdd_mux>; }; - usb1_vbus_reg: regulator@6 { + vdd_5v0_ts: regulator@6 { compatible = "regulator-fixed"; reg = <6>; - regulator-name = "usb1_vbus"; + regulator-name = "+5V_VDD_TS_SW"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-boot-on; + gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>; enable-active-high; - gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; - gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; }; - usb3_vbus_reg: regulator@7 { + vdd_usb1_vbus: regulator@7 { compatible = "regulator-fixed"; reg = <7>; - regulator-name = "usb3_vbus"; + regulator-name = "+5V_USB_HS"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - regulator-boot-on; + gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; enable-active-high; - gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; }; - panel_3v3_reg: regulator@8 { + vdd_usb3_vbus: regulator@8 { compatible = "regulator-fixed"; reg = <8>; - regulator-name = "panel_3v3"; + regulator-name = "+5V_USB_SS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; + enable-active-high; + gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_3v3_panel: regulator@9 { + compatible = "regulator-fixed"; + reg = <9>; + regulator-name = "+3.3V_PANEL"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - enable-active-high; gpio = <&as3722 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_run>; + }; + + vdd_3v3_lp0: regulator@10 { + compatible = "regulator-fixed"; + reg = <10>; + regulator-name = "+3.3V_LP0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* + * TODO: find a way to wire this up with the USB EHCI + * controllers so that it can be enabled on demand. + */ + regulator-always-on; + gpio = <&as3722 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_sys>; }; };
Signature · 1 line
1.8.4.2
A message that is not in the archive (sent off-list or not yet received): 1393431629-7040-1-git-send-email-thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org
PATCH 2/7 ARM: tegra: Hook up SDMMC3 power-supply on Venice2
From: Thierry Reding <[email protected]>
The SDMMC3 interface is supplied with 1.8V by the PMICs LDO6.
--- arch/arm/boot/dts/tegra124-venice2.dts | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)
arch/arm/boot/dts/tegra124-venice2.dts +2 -3
@@ -763,12 +763,10 @@ regulator-max-microvolt = <1200000>; }; - ldo6 { + vddio_sdmmc3: ldo6 { regulator-name = "+VDDIO_SDMMC3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; }; ldo7 {
@@ -930,6 +928,7 @@ power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; status = "okay"; bus-width = <4>; + vmmc-supply = <&vddio_sdmmc3>; }; sdhci@700b0600 {
Signature · 1 line
1.8.4.2
PATCH 3/7 ARM: tegra: Add Tegra124 host1x support
In reply to a message not in the archiveFrom: Thierry Reding <[email protected]>
The version of host1x found on Tegra124 SoCs isn't compatible to earlier versions since some of the registers have moved in order to increase the capabilities.
--- arch/arm/boot/dts/tegra124.dtsi | 41 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 41 insertions(+)
arch/arm/boot/dts/tegra124.dtsi +41 -0
@@ -9,6 +9,47 @@ compatible = "nvidia,tegra124"; interrupt-parent = <&gic>; + host1x@50000000 { + compatible = "nvidia,tegra124-host1x", "simple-bus"; + reg = <0x50000000 0x00034000>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */ + <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* general */ + clocks = <&tegra_car TEGRA124_CLK_HOST1X>; + resets = <&tegra_car 28>; + reset-names = "host1x"; + + #address-cells = <1>; + #size-cells = <1>; + + ranges = <0x54000000 0x54000000 0x01000000>; + + dc@54200000 { + compatible = "nvidia,tegra124-dc"; + reg = <0x54200000 0x00040000>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DISP1>, + <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 27>; + reset-names = "dc"; + + nvidia,head = <0>; + }; + + dc@54240000 { + compatible = "nvidia,tegra124-dc"; + reg = <0x54240000 0x00040000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DISP2>, + <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 26>; + reset-names = "dc"; + + nvidia,head = <1>; + }; + }; + gic: interrupt-controller@50041000 { compatible = "arm,cortex-a15-gic"; #interrupt-cells = <3>;
Signature · 1 line
1.8.4.2
PATCH 4/7 ARM: tegra: Add Tegra124 eDP support
In reply to a message not in the archiveFrom: Thierry Reding <[email protected]>
Tegra124 has a pair of controllers (SOR and DPAUX) that together can be used to drive eDP panels.
--- arch/arm/boot/dts/tegra124.dtsi | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+)
arch/arm/boot/dts/tegra124.dtsi +26 -0
@@ -48,6 +48,32 @@ nvidia,head = <1>; }; + + sor@54540000 { + compatible = "nvidia,tegra124-sor"; + reg = <0x54540000 0x00040000>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_SOR0>, + <&tegra_car TEGRA124_CLK_PLL_D_OUT0>, + <&tegra_car TEGRA124_CLK_PLL_DP>, + <&tegra_car TEGRA124_CLK_CLK_M>; + clock-names = "sor", "parent", "dp", "safe"; + resets = <&tegra_car 182>; + reset-names = "sor"; + status = "disabled"; + }; + + dpaux@545c0000 { + compatible = "nvidia,tegra124-dpaux"; + reg = <0x545c0000 0x00040000>; + interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DPAUX>, + <&tegra_car TEGRA124_CLK_PLL_DP>; + clock-names = "dpaux", "parent"; + resets = <&tegra_car 181>; + reset-names = "dpaux"; + status = "disabled"; + }; }; gic: interrupt-controller@50041000 {
Signature · 1 line
1.8.4.2
PATCH 5/7 ARM: tegra: Enable eDP for Venice2
In reply to a message not in the archiveFrom: Thierry Reding <[email protected]>
Venice2 has a 12.9" (2560x1700) panel connected to the eDP output of the Tegra124. The panel has an EDID to describe the video timings but needs a few extra nodes to get the backlight to come up.
--- arch/arm/boot/dts/tegra124-venice2.dts | 32 ++++++++++++++++++++++++++++++++ 1 file changed, 32 insertions(+)
arch/arm/boot/dts/tegra124-venice2.dts +32 -0
@@ -16,6 +16,20 @@ reg = <0x80000000 0x80000000>; }; + host1x@50000000 { + sor@54540000 { + status = "okay"; + + nvidia,dpaux = <&dpaux>; + nvidia,panel = <&panel>; + }; + + dpaux: dpaux@545c0000 { + vdd-supply = <&vdd_3v3_panel>; + status = "okay"; + }; + }; + pinmux: pinmux@70000868 { pinctrl-names = "default"; pinctrl-0 = <&pinmux_default>;
@@ -942,6 +956,17 @@ }; }; + backlight: backlight { + compatible = "pwm-backlight"; + + enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>; + power-supply = <&vdd_led>; + pwms = <&pwm 1 1000000>; + + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; + clocks { compatible = "simple-bus"; #address-cells = <1>;
@@ -967,6 +992,13 @@ }; }; + panel: panel { + compatible = "lg,lp129qe", "simple-panel"; + + backlight = <&backlight>; + ddc-i2c-bus = <&dpaux>; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>;
Signature · 1 line
1.8.4.2
PATCH 6/7 ARM: tegra: Add Tegra124 USB support
In reply to a message not in the archiveFrom: Thierry Reding <[email protected]>
The USB controllers on Tegra124 are backwards-compatible with those found on Tegra30.
--- arch/arm/boot/dts/tegra124.dtsi | 99 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 99 insertions(+)
arch/arm/boot/dts/tegra124.dtsi +99 -0
@@ -591,6 +591,105 @@ }; }; + usb@7d000000 { + compatible = "nvidia,tegra30-ehci", "usb-ehci"; + reg = <0x7d000000 0x4000>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USBD>; + resets = <&tegra_car 22>; + reset-names = "usb"; + nvidia,phy = <&phy1>; + status = "disabled"; + }; + + phy1: usb-phy@7d000000 { + compatible = "nvidia,tegra30-usb-phy"; + reg = <0x7d000000 0x4000 0x7d000000 0x4000>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USBD>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + status = "disabled"; + }; + + usb@7d004000 { + compatible = "nvidia,tegra30-ehci", "usb-ehci"; + reg = <0x7d004000 0x4000>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB2>; + resets = <&tegra_car 58>; + reset-names = "usb"; + nvidia,phy = <&phy2>; + status = "disabled"; + }; + + phy2: usb-phy@7d004000 { + compatible = "nvidia,tegra30-usb-phy"; + reg = <0x7d004000 0x4000 0x7d000000 0x4000>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB2>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + status = "disabled"; + }; + + usb@7d008000 { + compatible = "nvidia,tegra30-ehci", "usb-ehci"; + reg = <0x7d008000 0x4000>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB3>; + resets = <&tegra_car 59>; + reset-names = "usb"; + nvidia,phy = <&phy3>; + status = "disabled"; + }; + + phy3: usb-phy@7d008000 { + compatible = "nvidia,tegra30-usb-phy"; + reg = <0x7d008000 0x4000 0x7d000000 0x4000>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB3>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + status = "disabled"; + }; + cpus { #address-cells = <1>; #size-cells = <0>;
Signature · 1 line
1.8.4.2
A message that is not in the archive (sent off-list or not yet received): 1393431629-7040-6-git-send-email-thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org
Re: [PATCH 6/7] ARM: tegra: Add Tegra124 USB support
arch/arm/boot/dts/tegra124.dtsi line 595
Quoted 9 lines · Thierry Reding
From: Thierry Reding <[email protected]>
The USB controllers on Tegra124 are backwards-compatible with those found on Tegra30.
arch/arm/boot/dts/tegra124.dtsi +2
-0+ usb@7d000000 { + compatible = "nvidia,tegra30-ehci", "usb-ehci";
These properties still all need the Tegra124 value in there too, just in case there's a need to differentiate in the future. I can fix that up when applying.
A message that is not in the archive (sent off-list or not yet received): [email protected]
Re: [PATCH 6/7] ARM: tegra: Add Tegra124 USB support
Quoted 6 lines · Stephen Warren
Quoted 4 lines · Thierry Reding
From: Thierry Reding <[email protected]>
The USB controllers on Tegra124 are backwards-compatible with those found on Tegra30.
Quoted 8 lines
arch/arm/boot/dts/tegra124.dtsi line 595
Quoted 4 lines
arch/arm/boot/dts/tegra124.dtsi +2
-0+ usb@7d000000 { + compatible = "nvidia,tegra30-ehci", "usb-ehci";These properties still all need the Tegra124 value in there too, just in case there's a need to differentiate in the future. I can fix that up when applying.
I've added those in v3 that I just sent out. I added Tegra124 values for both the USB EHCI controllers as well as the PHY nodes.
Thierry
PATCH 7/7 ARM: tegra: Enable USB on Venice2
In reply to a message not in the archiveFrom: Thierry Reding <[email protected]>
USB1 and USB3 are routed to two external connectors, while USB2 is used for the integrated webcam.
--- arch/arm/boot/dts/tegra124-venice2.dts | 29 ++++++++++++++++++++++++++++- 1 file changed, 28 insertions(+), 1 deletion(-)
arch/arm/boot/dts/tegra124-venice2.dts +28 -1
@@ -765,7 +765,7 @@ ams,enable-tracking; }; - ldo4 { + vdd_run_cam: ldo4 { regulator-name = "+3.3V_RUN_CAM"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>;
@@ -956,6 +956,33 @@ }; }; + usb@7d000000 { + status = "okay"; + }; + + usb-phy@7d000000 { + status = "okay"; + vbus-supply = <&vdd_usb1_vbus>; + }; + + usb@7d004000 { + status = "okay"; + }; + + usb-phy@7d004000 { + status = "okay"; + vbus-supply = <&vdd_run_cam>; + }; + + usb@7d008000 { + status = "okay"; + }; + + usb-phy@7d008000 { + status = "okay"; + vbus-supply = <&vdd_usb3_vbus>; + }; + backlight: backlight { compatible = "pwm-backlight";
Signature · 1 line
1.8.4.2