Skip to contentSkip to conversation

spi: clps711x: Convert to use master->max_speed_hz

PATCH Applied Axel Lin 2 participants 2 messages Mar 26, 2014 – Mar 27, 2014 SPI

lore
Share & tools
lore

Axel Lin

author
#0 lore raw

PATCH 1/1 spi: clps711x: Convert to use master->max_speed_hz

Set highest transfer speed to master->max_speed_hz and then we can remove hw->max_speed.

Signed-off-by Axel Lin <[email protected]>
---
 drivers/spi/spi-clps711x.c | 14 +++++++-------
 1 file changed, 7 insertions(+), 7 deletions(-)
drivers/spi/spi-clps711x.c +7 -7
index d623500..4cd62f6 100644
@@ -32,7 +32,6 @@ struct spi_clps711x_data {
 	struct regmap		*syscon;
 	struct regmap		*syscon1;
 	struct clk		*spi_clk;
-	u32			max_speed_hz;
 
 	u8			*tx_buf;
 	u8			*rx_buf;

@@ -51,16 +50,17 @@ static int spi_clps711x_setup(struct spi_device *spi)
 static void spi_clps711x_setup_xfer(struct spi_device *spi,
 				    struct spi_transfer *xfer)
 {
-	struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
+	struct spi_master *master = spi->master;
+	struct spi_clps711x_data *hw = spi_master_get_devdata(master);
 
 	/* Setup SPI frequency divider */
-	if (!xfer->speed_hz || (xfer->speed_hz >= hw->max_speed_hz))
+	if (xfer->speed_hz >= master->max_speed_hz)
 		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
 				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(3));
-	else if (xfer->speed_hz >= (hw->max_speed_hz / 2))
+	else if (xfer->speed_hz >= (master->max_speed_hz / 2))
 		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
 				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(2));
-	else if (xfer->speed_hz >= (hw->max_speed_hz / 8))
+	else if (xfer->speed_hz >= (master->max_speed_hz / 8))
 		regmap_update_bits(hw->syscon1, SYSCON_OFFSET,
 				   SYSCON1_ADCKSEL_MASK, SYSCON1_ADCKSEL(1));
 	else

@@ -182,7 +182,7 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 		ret = PTR_ERR(hw->spi_clk);
 		goto err_out;
 	}
-	hw->max_speed_hz = clk_get_rate(hw->spi_clk);
+	master->max_speed_hz = clk_get_rate(hw->spi_clk);
 
 	platform_set_drvdata(pdev, master);
 

@@ -220,7 +220,7 @@ static int spi_clps711x_probe(struct platform_device *pdev)
 	if (!ret) {
 		dev_info(&pdev->dev,
 			 "SPI bus driver initialized. Master clock %u Hz\n",
-			 hw->max_speed_hz);
+			 master->max_speed_hz);
 		return 0;
 	}
Signature · 8 lines
1.8.3.2



--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Applied
#1 lore raw
Quoted 2 lines · Axel Lin

Set highest transfer speed to master->max_speed_hz and then we can remove hw->max_speed.

Applied, thanks.