Skip to contentSkip to conversation

drm/i915/bdw: Set initial rps freq to RP1

PATCH In review Ben Widawsky 2 participants 5 messages Apr 1, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/4 drm/i915/bdw: Set initial rps freq to RP1

Programming it outside of the rp0-rp1 range is considered a programming error. Since we do not know that the previous value would actually be in the range, program something we've read from the hardware, and therefore know will work.

This is potentially an issue for platforms whose ranges are outside the norms given in the programming guide (ie. early silicon)

v2: Use RP1 instead of RPn

---
 drivers/gpu/drm/i915/intel_pm.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +4 -2
index e9a9aef..51ff40e 100644
@@ -3284,8 +3284,10 @@ static void gen8_enable_rps(struct drm_device *dev)
 				    rc6_mask);
 
 	/* 4 Program defaults and thresholds for RPS*/
-	I915_WRITE(GEN6_RPNSWREQ, HSW_FREQUENCY(10)); /* Request 500 MHz */
-	I915_WRITE(GEN6_RC_VIDEO_FREQ, HSW_FREQUENCY(12)); /* Request 600 MHz */
+	I915_WRITE(GEN6_RPNSWREQ,
+		   HSW_FREQUENCY(dev_priv->rps.rp1_freq));
+	I915_WRITE(GEN6_RC_VIDEO_FREQ,
+		   HSW_FREQUENCY(dev_priv->rps.rp1_freq));
 	/* NB: Docs say 1s, and 1000000 - which aren't equivalent */
 	I915_WRITE(GEN6_RP_DOWN_TIMEOUT, 100000000 / 128); /* 1 second timeout */
 
Signature · 1 line
1.9.1
#1 lore raw

PATCH 2/4 drm/i915/bdw: Extract rp_state_caps logic

We have a need for duplicated parsing of the RP_STATE_CAPS register (and the setting of the associated fields). To reuse some code, we can extract the function into a simple helper.

This patch also addresses the fact that we missed doing this for gen8, something we should have done anyway.

This could be two patches, one to extract, and one to add gen8, but it's trivial enough that I think one is fine. I will accept a request to split it. Please notice the fix addressed by v2 below.

Valleyview is left untouched because it is different.

v2: Logically rebased on top of
commit dd0a1aa19bd3d7203e58157b84cea78bbac605ac

Author: Jeff McGee <[email protected]>
Date:   Tue Feb 4 11:32:31 2014 -0600

drm/i915: Restore rps/rc6 on reset

Note with the above change the fix for gen8 is also handled (which was not the case in Jeff's original patch).

---
 drivers/gpu/drm/i915/intel_pm.c | 40 +++++++++++++++++++++++-----------------
 1 file changed, 23 insertions(+), 17 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +23 -17
index 51ff40e..ed45143 100644
@@ -3247,6 +3247,27 @@ static void gen6_enable_rps_interrupts(struct drm_device *dev)
 	spin_unlock_irq(&dev_priv->irq_lock);
 }
 
+static void parse_rp_state_cap(struct drm_i915_private *dev_priv, u32 rp_state_cap)
+{
+	/* All of these values are in units of 50MHz */
+	dev_priv->rps.cur_freq		= 0;
+	/* static values from HW: RP0 < RPe < RP1 < RPn (min_freq) */
+	dev_priv->rps.rp1_freq		= (rp_state_cap >>  8) & 0xff;
+	dev_priv->rps.rp0_freq		= (rp_state_cap >>  0) & 0xff;
+	dev_priv->rps.min_freq		= (rp_state_cap >> 16) & 0xff;
+	/* XXX: only BYT has a special efficient freq */
+	dev_priv->rps.efficient_freq	= dev_priv->rps.rp1_freq;
+	/* hw_max = RP0 until we check for overclocking */
+	dev_priv->rps.max_freq		= dev_priv->rps.rp0_freq;
+
+	/* Preserve min/max settings in case of re-init */
+	if (dev_priv->rps.max_freq_softlimit == 0)
+		dev_priv->rps.max_freq_softlimit = dev_priv->rps.max_freq;
+
+	if (dev_priv->rps.min_freq_softlimit == 0)
+		dev_priv->rps.min_freq_softlimit = dev_priv->rps.min_freq;
+}
+
 static void gen8_enable_rps(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
@@ -3265,6 +3286,7 @@ static void gen8_enable_rps(struct drm_device *dev)
 	I915_WRITE(GEN6_RC_CONTROL, 0);
 
 	rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
+	parse_rp_state_cap(dev_priv, rp_state_cap);
 
 	/* 2b: Program RC6 thresholds.*/
 	I915_WRITE(GEN6_RC6_WAKE_RATE_LIMIT, 40 << 16);
@@ -3353,23 +3375,7 @@ static void gen6_enable_rps(struct drm_device *dev)
 	rp_state_cap = I915_READ(GEN6_RP_STATE_CAP);
 	gt_perf_status = I915_READ(GEN6_GT_PERF_STATUS);
 
-	/* All of these values are in units of 50MHz */
-	dev_priv->rps.cur_freq		= 0;
-	/* static values from HW: RP0 < RPe < RP1 < RPn (min_freq) */
-	dev_priv->rps.rp1_freq		= (rp_state_cap >>  8) & 0xff;
-	dev_priv->rps.rp0_freq		= (rp_state_cap >>  0) & 0xff;
-	dev_priv->rps.min_freq		= (rp_state_cap >> 16) & 0xff;
-	/* XXX: only BYT has a special efficient freq */
-	dev_priv->rps.efficient_freq	= dev_priv->rps.rp1_freq;
-	/* hw_max = RP0 until we check for overclocking */
-	dev_priv->rps.max_freq		= dev_priv->rps.rp0_freq;
-
-	/* Preserve min/max settings in case of re-init */
-	if (dev_priv->rps.max_freq_softlimit == 0)
-		dev_priv->rps.max_freq_softlimit = dev_priv->rps.max_freq;
-
-	if (dev_priv->rps.min_freq_softlimit == 0)
-		dev_priv->rps.min_freq_softlimit = dev_priv->rps.min_freq;
+	parse_rp_state_cap(dev_priv, rp_state_cap);
 
 	/* disable the counters and set deterministic thresholds */
 	I915_WRITE(GEN6_RC_CONTROL, 0);
Signature · 1 line
1.9.1
#2 lore raw

PATCH 3/4 drm/i915/bdw: RPS frequency bits are the same as HSW

In reply to Ben Widawsky
---
 drivers/gpu/drm/i915/intel_pm.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/intel_pm.c +1 -1
index ed45143..9728c2c 100644
@@ -3041,7 +3041,7 @@ void gen6_set_rps(struct drm_device *dev, u8 val)
 	if (val != dev_priv->rps.cur_freq) {
 		gen6_set_rps_thresholds(dev_priv, val);
 
-		if (IS_HASWELL(dev))
+		if (IS_HASWELL(dev) || IS_BROADWELL(dev))
 			I915_WRITE(GEN6_RPNSWREQ,
 				   HSW_FREQUENCY(val));
 		else
Signature · 1 line
1.9.1
#3 lore raw

PATCH 4/4 drm/i915/bdw: Implement a basic PM interrupt handler

In reply to Ben Widawsky

Almost all of it is reusable from the existing code. The primary difference is we need to do even less in the interrupt handler, since interrupts are not shared in the same way.

The patch is mostly a copy-paste of the existing snb+ code, with updates to the relevant parts requiring changes to the interrupt handling. As such it /should/ be relatively trivial. It's highly likely that I missed some places where I need a gen8 version of the PM interrupts, but it has become invisible to me by now.

This patch could probably be split into adding the new functions, followed by actually handling the interrupts. Since the code is currently disabled (and broken) I think the patch stands better by itself.

v2: Move the commit about not touching the ringbuffer interrupt to the snb_* function where it belongs (Rodrigo)

v3: Rebased on Paulo's runtime PM changes

Conflicts:

	drivers/gpu/drm/i915/i915_irq.c
---
 drivers/gpu/drm/i915/i915_irq.c  | 84 +++++++++++++++++++++++++++++++++++++---
 drivers/gpu/drm/i915/i915_reg.h  |  1 +
 drivers/gpu/drm/i915/intel_drv.h |  2 +
 drivers/gpu/drm/i915/intel_pm.c  | 39 ++++++++++++++++++-
 4 files changed, 119 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/i915_irq.c +79 -5
index c8d2445..f9157dc 100644
@@ -214,6 +214,53 @@ static bool ivb_can_enable_err_int(struct drm_device *dev)
 	return true;
 }
 
+/**
+  * bdw_update_pm_irq - update GT interrupt 2
+  * @dev_priv: driver private
+  * @interrupt_mask: mask of interrupt bits to update
+  * @enabled_irq_mask: mask of interrupt bits to enable
+  *
+  * Copied from the snb function, updated with relevant register offsets
+  */
+static void bdw_update_pm_irq(struct drm_i915_private *dev_priv,
+			      uint32_t interrupt_mask,
+			      uint32_t enabled_irq_mask)
+{
+	uint32_t new_val;
+
+	assert_spin_locked(&dev_priv->irq_lock);
+
+	if (dev_priv->pm.irqs_disabled) {
+		WARN(1, "IRQs disabled\n");
+		dev_priv->pm.regsave.gen6_pmimr &= ~interrupt_mask;
+		dev_priv->pm.regsave.gen6_pmimr |= (~enabled_irq_mask &
+						     interrupt_mask);
+		return;
+	}
+
+	new_val = dev_priv->pm_irq_mask;
+	new_val &= ~interrupt_mask;
+	new_val |= (~enabled_irq_mask & interrupt_mask);
+
+	if (new_val != dev_priv->pm_irq_mask) {
+		dev_priv->pm_irq_mask = new_val;
+		I915_WRITE(GEN8_GT_IMR(2), I915_READ(GEN8_GT_IMR(2)) |
+					   dev_priv->pm_irq_mask);
+		POSTING_READ(GEN8_GT_IMR(2));
+	}
+}
+
+void bdw_enable_pm_irq(struct drm_i915_private *dev_priv, uint32_t mask)
+{
+	bdw_update_pm_irq(dev_priv, mask, mask);
+}
+
+void bdw_disable_pm_irq(struct drm_i915_private *dev_priv, uint32_t mask)
+{
+	bdw_update_pm_irq(dev_priv, mask, 0);
+}
+
+
 static bool cpt_can_enable_serr_int(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
@@ -1094,13 +1141,17 @@ static void gen6_pm_rps_work(struct work_struct *work)
 	spin_lock_irq(&dev_priv->irq_lock);
 	pm_iir = dev_priv->rps.pm_iir;
 	dev_priv->rps.pm_iir = 0;
-	/* Make sure not to corrupt PMIMR state used by ringbuffer code */
-	snb_enable_pm_irq(dev_priv, dev_priv->pm_rps_events);
+	if (IS_BROADWELL(dev_priv->dev))
+		bdw_enable_pm_irq(dev_priv, dev_priv->pm_rps_events);
+	else {
+		/* Make sure not to corrupt PMIMR state used by ringbuffer */
+		snb_enable_pm_irq(dev_priv, dev_priv->pm_rps_events);
+		/* Make sure we didn't queue anything we're not going to
+		 * process. */
+		WARN_ON(pm_iir & ~dev_priv->pm_rps_events);
+	}
 	spin_unlock_irq(&dev_priv->irq_lock);
 
-	/* Make sure we didn't queue anything we're not going to process. */
-	WARN_ON(pm_iir & ~dev_priv->pm_rps_events);
-
 	if ((pm_iir & dev_priv->pm_rps_events) == 0)
 		return;
 
@@ -1292,6 +1343,19 @@ static void snb_gt_irq_handler(struct drm_device *dev,
 		ivybridge_parity_error_irq_handler(dev, gt_iir);
 }
 
+static void gen8_rps_irq_handler(struct drm_i915_private *dev_priv, u32 pm_iir)
+{
+	if ((pm_iir & GEN6_PM_RPS_EVENTS) == 0)
+		return;
+
+	spin_lock(&dev_priv->irq_lock);
+	dev_priv->rps.pm_iir |= pm_iir & GEN6_PM_RPS_EVENTS;
+	bdw_disable_pm_irq(dev_priv, pm_iir & GEN6_PM_RPS_EVENTS);
+	spin_unlock(&dev_priv->irq_lock);
+
+	queue_work(dev_priv->wq, &dev_priv->rps.work);
+}
+
 static irqreturn_t gen8_gt_irq_handler(struct drm_device *dev,
 				       struct drm_i915_private *dev_priv,
 				       u32 master_ctl)
@@ -1327,6 +1391,16 @@ static irqreturn_t gen8_gt_irq_handler(struct drm_device *dev,
 			DRM_ERROR("The master control interrupt lied (GT1)!\n");
 	}
 
+	if (master_ctl & GEN8_GT_PM_IRQ) {
+		tmp = I915_READ(GEN8_GT_IIR(2));
+		if (tmp & GEN6_PM_RPS_EVENTS) {
+			ret = IRQ_HANDLED;
+			gen8_rps_irq_handler(dev_priv, tmp);
+			I915_WRITE(GEN8_GT_IIR(1), tmp & GEN6_PM_RPS_EVENTS);
+		} else
+			DRM_ERROR("The master control interrupt lied (PM)!\n");
+	}
+
 	if (master_ctl & GEN8_GT_VECS_IRQ) {
 		tmp = I915_READ(GEN8_GT_IIR(3));
 		if (tmp) {
drivers/gpu/drm/i915/i915_reg.h +1 -0
index 1f927a5..6bc9c73 100644
@@ -4179,6 +4179,7 @@ enum punit_power_well {
 #define  GEN8_DE_PIPE_A_IRQ		(1<<16)
 #define  GEN8_DE_PIPE_IRQ(pipe)		(1<<(16+pipe))
 #define  GEN8_GT_VECS_IRQ		(1<<6)
+#define  GEN8_GT_PM_IRQ			(1<<4)
 #define  GEN8_GT_VCS2_IRQ		(1<<3)
 #define  GEN8_GT_VCS1_IRQ		(1<<2)
 #define  GEN8_GT_BCS_IRQ		(1<<1)
drivers/gpu/drm/i915/intel_drv.h +2 -0
index 9002e77..a9c5284 100644
@@ -629,6 +629,8 @@ void snb_enable_pm_irq(struct drm_i915_private *dev_priv, uint32_t mask);
 void snb_disable_pm_irq(struct drm_i915_private *dev_priv, uint32_t mask);
 void hsw_runtime_pm_disable_interrupts(struct drm_device *dev);
 void hsw_runtime_pm_restore_interrupts(struct drm_device *dev);
+void bdw_enable_pm_irq(struct drm_i915_private *dev_priv, uint32_t mask);
+void bdw_disable_pm_irq(struct drm_i915_private *dev_priv, uint32_t mask);
 
 
 /* intel_crt.c */
drivers/gpu/drm/i915/intel_pm.c +37 -2
index 9728c2c..2485962 100644
@@ -3165,6 +3165,25 @@ void valleyview_set_rps(struct drm_device *dev, u8 val)
 	trace_intel_gpu_freq_change(vlv_gpu_freq(dev_priv, val));
 }
 
+static void gen8_disable_rps_interrupts(struct drm_device *dev)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+
+	I915_WRITE(GEN6_PMINTRMSK, 0xffffffff);
+	I915_WRITE(GEN8_GT_IER(2), I915_READ(GEN8_GT_IER(2)) &
+				   ~GEN6_PM_RPS_EVENTS);
+	/* Complete PM interrupt masking here doesn't race with the rps work
+	 * item again unmasking PM interrupts because that is using a different
+	 * register (PMIMR) to mask PM interrupts. The only risk is in leaving
+	 * stale bits in PMIIR and PMIMR which gen6_enable_rps will clean up. */
+
+	spin_lock_irq(&dev_priv->irq_lock);
+	dev_priv->rps.pm_iir = 0;
+	spin_unlock_irq(&dev_priv->irq_lock);
+
+	I915_WRITE(GEN8_GT_IIR(2), GEN6_PM_RPS_EVENTS);
+}
+
 static void gen6_disable_rps_interrupts(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
@@ -3191,7 +3210,10 @@ static void gen6_disable_rps(struct drm_device *dev)
 	I915_WRITE(GEN6_RC_CONTROL, 0);
 	I915_WRITE(GEN6_RPNSWREQ, 1 << 31);
 
-	gen6_disable_rps_interrupts(dev);
+	if (IS_BROADWELL(dev))
+		gen8_disable_rps_interrupts(dev);
+	else
+		gen6_disable_rps_interrupts(dev);
 }
 
 static void valleyview_disable_rps(struct drm_device *dev)
@@ -3236,6 +3258,19 @@ int intel_enable_rc6(const struct drm_device *dev)
 	return INTEL_RC6_ENABLE;
 }
 
+static void gen8_enable_rps_interrupts(struct drm_device *dev)
+{
+	struct drm_i915_private *dev_priv = dev->dev_private;
+
+	spin_lock_irq(&dev_priv->irq_lock);
+	WARN_ON(dev_priv->rps.pm_iir);
+	bdw_enable_pm_irq(dev_priv, GEN6_PM_RPS_EVENTS);
+	I915_WRITE(GEN8_GT_IIR(2), GEN6_PM_RPS_EVENTS);
+	spin_unlock_irq(&dev_priv->irq_lock);
+
+	I915_WRITE(GEN6_PMINTRMSK, ~GEN6_PM_RPS_EVENTS);
+}
+
 static void gen6_enable_rps_interrupts(struct drm_device *dev)
 {
 	struct drm_i915_private *dev_priv = dev->dev_private;
@@ -3338,7 +3373,7 @@ static void gen8_enable_rps(struct drm_device *dev)
 
 	gen6_set_rps(dev, (I915_READ(GEN6_GT_PERF_STATUS) & 0xff00) >> 8);
 
-	gen6_enable_rps_interrupts(dev);
+	gen8_enable_rps_interrupts(dev);
 
 	gen6_gt_force_wake_put(dev_priv, FORCEWAKE_ALL);
 }
Signature · 1 line
1.9.1
#4 lore raw
In reply to Ben Widawsky
Quoted 5 lines · Ben Widawsky

Programming it outside of the rp0-rp1 range is considered a programming error. Since we do not know that the previous value would actually be in the range, program something we've read from the hardware, and therefore know will work.

Quoted 7 lines

This is potentially an issue for platforms whose ranges are outside the norms given in the programming guide (ie. early silicon)

v2: Use RP1 instead of RPn

For my own edification, I read the specs again (because of the RPS fallout) and the VIDEO_FREQ is simply an alternate to the normal boost frequency that we can select either manually or via the pcu for media workloads. We however combine the media workload into overall GPU activity and so only manage the single RPS frequency.

Therefore this patch is the right thing to do.
-Chris

Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre