usb: phy: msm: Fixes, cleanups and DT support
Subsystems (5)
v7 cover usb: phy: msm: Fixes, cleanups and DT support
From: "Ivan T. Ivanov" <[email protected]>
Hi,
This is a next version of patches posted earlier[1].
Hopefully comments from Felipe, Srinivas and Sergei have been addressed.
Changes since v6
- New patch "Enable deferred driver probing"
- Add log to patches wich did not have long description.
- Revert several changes not related to commit message.
[1] http://www.spinics.net/lists/linux-usb/msg106158.html
Ivan T. Ivanov (18):
usb: phy: msm: Make driver selectable on ARCH_QCOM
usb: phy: msm: Remove __init macro from driver probe method
usb: phy: msm: Move global regulators variables to driver state
usb: phy: msm: Enable deferred driver probing
usb: phy: msm: Migrate to Managed Device Resource allocation
usb: phy: msm: Remove unnecessarily check for valid regulators.
usb: phy: msm: Fix checkpatch.pl warnings
usb: phy: msm: Replace custom enum usb_mode_type with enum usb_dr_mode
usb: phy: msm: Remove unused pclk_src_name
usb: phy: msm: Remove HSUSB prefix from regulator names
usb: phy: msm: Properly check result from platform_get_irq()
usb: phy: msm: Add device tree support and binding information
usb: phy: msm: Use reset framework for LINK and PHY resets
usb: phy: msm: Add support for secondary PHY control
usb: phy: msm: Correct USB PHY Reset sequence for newer platform
usb: phy: msm: Handle disconnect events
usb: phy: msm: Vote for corner of VDD CX instead of voltage of VDD CX
usb: phy: msm: Use usb_add_phy_dev() to register device
Tim Bird (2):
usb: phy: msm: Fix PTS definitions for MSM USB controller
usb: phy: msm: Select secondary PHY via TCSR
.../devicetree/bindings/usb/msm-hsusb.txt | 78 +++ arch/arm/mach-msm/board-msm7x30.c | 2 +- arch/arm/mach-msm/board-qsd8x50.c | 2 +- drivers/usb/phy/Kconfig | 6 +- drivers/usb/phy/phy-msm-usb.c | 705 ++++++++++++--------- include/linux/usb/msm_hsusb.h | 39 +- include/linux/usb/msm_hsusb_hw.h | 14 +- 7 files changed, 509 insertions(+), 337 deletions(-)
--
1.8.3.2
PATCH v7 1/20 usb: phy: msm: Make driver selectable on ARCH_QCOM
From: "Ivan T. Ivanov" <[email protected]>
Controller could be found on APQ and MSM platforms, make configuration description more generic.
--- drivers/usb/phy/Kconfig | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/usb/phy/Kconfig +3 -3
@@ -171,11 +171,11 @@ config USB_ISP1301 module will be called phy-isp1301. config USB_MSM_OTG - tristate "OTG support for Qualcomm on-chip USB controller" - depends on (USB || USB_GADGET) && ARCH_MSM + tristate "Qualcomm on-chip USB OTG controller support" + depends on (USB || USB_GADGET) && (ARCH_MSM || ARCH_QCOM) select USB_PHY help - Enable this to support the USB OTG transceiver on MSM chips. It + Enable this to support the USB OTG transceiver on Qualcomm chips. It handles PHY initialization, clock management, and workarounds required after resetting the hardware and power management. This driver is required even for peripheral only or host only
Signature · 1 line
1.8.3.2
PATCH v7 2/20 usb: phy: msm: Remove __init macro from driver probe method
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
This fixes following:
WARNING: drivers/usb/phy/built-in.o(.data+0x68): Section mismatch in reference from the variable msm_otg_driver to the function .init.text:msm_otg_probe() The variable msm_otg_driver references
the function __init msm_otg_probe()
--- drivers/usb/phy/phy-msm-usb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/phy/phy-msm-usb.c +1 -1
@@ -1406,7 +1406,7 @@ static void msm_otg_debugfs_cleanup(void)debugfs_remove (msm_otg_dbg_root); } -static int __init msm_otg_probe (struct platform_device *pdev) +static int msm_otg_probe (struct platform_device *pdev) {int ret =0 ;struct resource *res;
Signature · 1 line
1.8.3.2
PATCH v7 3/20 usb: phy: msm: Move global regulators variables to driver state
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Eliminating global variables allows driver to handle multiple device instances.
--- drivers/usb/phy/phy-msm-usb.c | 82 ++++++++++++++++++++----------------------- include/linux/usb/msm_hsusb.h | 3 ++ 2 files changed, 42 insertions(+), 43 deletions(-)
drivers/usb/phy/phy-msm-usb.c +39 -43
@@ -58,47 +58,43 @@#define USB_PHY_VDD_DIG_VOL_MIN 1000000/* uV */ #define USB_PHY_VDD_DIG_VOL_MAX 1320000/* uV */ -static struct regulator *hsusb_3p3; -static struct regulator *hsusb_1p8; -static struct regulator *hsusb_vddcx; -static int msm_hsusb_init_vddcx (struct msm_otg *motg,int init) {int ret =0 ;if (init) { - hsusb_vddcx =regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); -if (IS_ERR (hsusb_vddcx)) { + motg->vddcx =regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); +if (IS_ERR (motg->vddcx)) {dev_err (motg->phy.dev,"unable to get hsusb vddcx\n" ); -return PTR_ERR (hsusb_vddcx); +return PTR_ERR (motg->vddcx); } - ret =regulator_set_voltage (hsusb_vddcx, + ret =regulator_set_voltage (motg->vddcx,USB_PHY_VDD_DIG_VOL_MIN ,USB_PHY_VDD_DIG_VOL_MAX );if (ret) {dev_err (motg->phy.dev,"unable to set the voltage " "for hsusb vddcx\n" ); -regulator_put (hsusb_vddcx); +regulator_put (motg->vddcx);return ret; } - ret =regulator_enable (hsusb_vddcx); + ret =regulator_enable (motg->vddcx);if (ret) {dev_err (motg->phy.dev,"unable to enable hsusb vddcx\n" ); -regulator_put (hsusb_vddcx); +regulator_put (motg->vddcx); } }else { - ret =regulator_set_voltage (hsusb_vddcx,0 , + ret =regulator_set_voltage (motg->vddcx,0 ,USB_PHY_VDD_DIG_VOL_MAX );if (ret)dev_err (motg->phy.dev,"unable to set the voltage " "for hsusb vddcx\n" ); - ret =regulator_disable (hsusb_vddcx); + ret =regulator_disable (motg->vddcx);if (ret)dev_err (motg->phy.dev,"unable to disable hsusb vddcx\n" ); -regulator_put (hsusb_vddcx); +regulator_put (motg->vddcx); }return ret;
@@ -109,38 +105,38 @@ static int msm_hsusb_ldo_init(struct msm_otg *motg, int init)int rc =0 ;if (init) { - hsusb_3p3 =regulator_get (motg->phy.dev,"HSUSB_3p3" ); -if (IS_ERR (hsusb_3p3)) { + motg->v3p3 =regulator_get (motg->phy.dev,"HSUSB_3p3" ); +if (IS_ERR (motg->v3p3)) {dev_err (motg->phy.dev,"unable to get hsusb 3p3\n" ); -return PTR_ERR (hsusb_3p3); +return PTR_ERR (motg->v3p3); } - rc =regulator_set_voltage (hsusb_3p3,USB_PHY_3P3_VOL_MIN , + rc =regulator_set_voltage (motg->v3p3,USB_PHY_3P3_VOL_MIN ,USB_PHY_3P3_VOL_MAX );if (rc) {dev_err (motg->phy.dev,"unable to set voltage level " "for hsusb 3p3\n" ); goto put_3p3; } - rc =regulator_enable (hsusb_3p3); + rc =regulator_enable (motg->v3p3);if (rc) {dev_err (motg->phy.dev,"unable to enable the hsusb 3p3\n" ); goto put_3p3; } - hsusb_1p8 =regulator_get (motg->phy.dev,"HSUSB_1p8" ); -if (IS_ERR (hsusb_1p8)) { + motg->v1p8 =regulator_get (motg->phy.dev,"HSUSB_1p8" ); +if (IS_ERR (motg->v1p8)) {dev_err (motg->phy.dev,"unable to get hsusb 1p8\n" ); - rc =PTR_ERR (hsusb_1p8); + rc =PTR_ERR (motg->v1p8); goto disable_3p3; } - rc =regulator_set_voltage (hsusb_1p8,USB_PHY_1P8_VOL_MIN , + rc =regulator_set_voltage (motg->v1p8,USB_PHY_1P8_VOL_MIN ,USB_PHY_1P8_VOL_MAX );if (rc) {dev_err (motg->phy.dev,"unable to set voltage level " "for hsusb 1p8\n" ); goto put_1p8; } - rc =regulator_enable (hsusb_1p8); + rc =regulator_enable (motg->v1p8);if (rc) {dev_err (motg->phy.dev,"unable to enable the hsusb 1p8\n" ); goto put_1p8;
@@ -149,54 +145,54 @@ static int msm_hsusb_ldo_init(struct msm_otg *motg, int init)return 0 ; } -regulator_disable (hsusb_1p8); +regulator_disable (motg->v1p8); put_1p8: -regulator_put (hsusb_1p8); +regulator_put (motg->v1p8); disable_3p3: -regulator_disable (hsusb_3p3); +regulator_disable (motg->v3p3); put_3p3: -regulator_put (hsusb_3p3); +regulator_put (motg->v3p3);return rc; } -static int msm_hsusb_ldo_set_mode (int on) +static int msm_hsusb_ldo_set_mode (struct msm_otg *motg,int on) {int ret =0 ; -if (!hsusb_1p8 ||IS_ERR (hsusb_1p8)) { +if (!motg->v1p8 ||IS_ERR (motg->v1p8)) {pr_err ("%s: HSUSB_1p8 is not initialized\n" , __func__);return -ENODEV ; } -if (!hsusb_3p3 ||IS_ERR (hsusb_3p3)) { +if (!motg->v3p3 ||IS_ERR (motg->v3p3)) {pr_err ("%s: HSUSB_3p3 is not initialized\n" , __func__);return -ENODEV ; }if (on) { - ret =regulator_set_optimum_mode (hsusb_1p8, + ret =regulator_set_optimum_mode (motg->v1p8,USB_PHY_1P8_HPM_LOAD );if (ret <0 ) {pr_err ("%s: Unable to set HPM of the regulator " "HSUSB_1p8\n" , __func__);return ret; } - ret =regulator_set_optimum_mode (hsusb_3p3, + ret =regulator_set_optimum_mode (motg->v3p3,USB_PHY_3P3_HPM_LOAD );if (ret <0 ) {pr_err ("%s: Unable to set HPM of the regulator " "HSUSB_3p3\n" , __func__); -regulator_set_optimum_mode (hsusb_1p8, +regulator_set_optimum_mode (motg->v1p8,USB_PHY_1P8_LPM_LOAD );return ret; } }else { - ret =regulator_set_optimum_mode (hsusb_1p8, + ret =regulator_set_optimum_mode (motg->v1p8,USB_PHY_1P8_LPM_LOAD );if (ret <0 )pr_err ("%s: Unable to set LPM of the regulator " "HSUSB_1p8\n" , __func__); - ret =regulator_set_optimum_mode (hsusb_3p3, + ret =regulator_set_optimum_mode (motg->v3p3,USB_PHY_3P3_LPM_LOAD );if (ret <0 ) pr_err("%s: Unable to set LPM of the regulator "
@@ -417,7 +413,7 @@ static int msm_otg_reset(struct usb_phy *phy)#ifdef CONFIG_PM #define USB_PHY_SUSP_DIG_VOL 500000 -static int msm_hsusb_config_vddcx (int high) +static int msm_hsusb_config_vddcx (struct msm_otg *motg,int high) {int max_vol =USB_PHY_VDD_DIG_VOL_MAX ;int min_vol;
@@ -428,7 +424,7 @@ static int msm_hsusb_config_vddcx(int high)else min_vol =USB_PHY_SUSP_DIG_VOL ; - ret =regulator_set_voltage (hsusb_vddcx, min_vol, max_vol); + ret =regulator_set_voltage (motg->vddcx, min_vol, max_vol);if (ret) {pr_err ("%s: unable to set the voltage for regulator " "HSUSB_VDDCX\n" , __func__);
@@ -518,8 +514,8 @@ static int msm_otg_suspend(struct msm_otg *motg)if (motg->pdata->phy_type ==SNPS_28NM_INTEGRATED_PHY && motg->pdata->otg_control ==OTG_PMIC_CONTROL ) { -msm_hsusb_ldo_set_mode (0 ); -msm_hsusb_config_vddcx (0 ); +msm_hsusb_ldo_set_mode (motg,0 ); +msm_hsusb_config_vddcx (motg,0 ); }if (device_may_wakeup (phy->dev))
@@ -555,8 +551,8 @@ static int msm_otg_resume(struct msm_otg *motg)if (motg->pdata->phy_type ==SNPS_28NM_INTEGRATED_PHY && motg->pdata->otg_control ==OTG_PMIC_CONTROL ) { -msm_hsusb_ldo_set_mode (1 ); -msm_hsusb_config_vddcx (1 ); +msm_hsusb_ldo_set_mode (motg,1 ); +msm_hsusb_config_vddcx (motg,1 );writel (readl (USB_PHY_CTRL ) & ~PHY_RETEN ,USB_PHY_CTRL ); }
@@ -1521,7 +1517,7 @@ static int msm_otg_probe(struct platform_device *pdev)dev_err (&pdev->dev,"hsusb vreg configuration failed\n" ); goto vddcx_exit; } - ret =msm_hsusb_ldo_set_mode (1 ); + ret =msm_hsusb_ldo_set_mode (motg,1 );if (ret) {dev_err (&pdev->dev,"hsusb vreg enable failed\n" ); goto ldo_exit;
include/linux/usb/msm_hsusb.h +3 -0
@@ -183,6 +183,9 @@ struct msm_otg {enum usb_chg_state chg_state;enum usb_chg_type chg_type;u8 dcd_retries; +struct regulator *v3p3; +struct regulator *v1p8; + struct regulator *vddcx; };#endif
--
1.8.3.2
PATCH v7 4/20 usb: phy: msm: Enable deferred driver probing
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Using platform_driver_probe() prevent driver from requesting probe deferral. Fix this.
--- drivers/usb/phy/phy-msm-usb.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/usb/phy/phy-msm-usb.c +2 -1
@@ -1736,6 +1736,7 @@ static const struct dev_pm_ops msm_otg_dev_pm_ops = { };static struct platform_driver msm_otg_driver = { + .probe = msm_otg_probe, .remove = msm_otg_remove, .driver = { .name =DRIVER_NAME ,
@@ -1744,7 +1745,7 @@ static struct platform_driver msm_otg_driver = { }, }; -module_platform_driver_probe (msm_otg_driver, msm_otg_probe); +module_platform_driver (msm_otg_driver);MODULE_LICENSE ("GPL v2" );MODULE_DESCRIPTION ("MSM USB transceiver driver" );
--
1.8.3.2
PATCH v7 5/20 usb: phy: msm: Migrate to Managed Device Resource allocation
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Move memory, regulators, clocks and irq allocation to devm_* variants. Properly check for valid clk handles.
--- drivers/usb/phy/phy-msm-usb.c | 192 ++++++++++++++++-------------------------- 1 file changed, 73 insertions(+), 119 deletions(-)
drivers/usb/phy/phy-msm-usb.c +73 -119
@@ -63,27 +63,18 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)int ret =0 ;if (init) { - motg->vddcx =regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); -if (IS_ERR (motg->vddcx)) { -dev_err (motg->phy.dev,"unable to get hsusb vddcx\n" ); -return PTR_ERR (motg->vddcx); - } - ret =regulator_set_voltage (motg->vddcx,USB_PHY_VDD_DIG_VOL_MIN ,USB_PHY_VDD_DIG_VOL_MAX );if (ret) {dev_err (motg->phy.dev,"unable to set the voltage " "for hsusb vddcx\n" ); -regulator_put (motg->vddcx);return ret; } ret =regulator_enable (motg->vddcx); -if (ret) { +if (ret)dev_err (motg->phy.dev,"unable to enable hsusb vddcx\n" ); -regulator_put (motg->vddcx); - } }else { ret =regulator_set_voltage (motg->vddcx,0 ,USB_PHY_VDD_DIG_VOL_MAX );
@@ -93,8 +84,6 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init) ret =regulator_disable (motg->vddcx);if (ret)dev_err (motg->phy.dev,"unable to disable hsusb vddcx\n" ); - -regulator_put (motg->vddcx); }return ret;
@@ -105,53 +94,38 @@ static int msm_hsusb_ldo_init(struct msm_otg *motg, int init)int rc =0 ;if (init) { - motg->v3p3 =regulator_get (motg->phy.dev,"HSUSB_3p3" ); -if (IS_ERR (motg->v3p3)) { -dev_err (motg->phy.dev,"unable to get hsusb 3p3\n" ); -return PTR_ERR (motg->v3p3); - } - rc =regulator_set_voltage (motg->v3p3,USB_PHY_3P3_VOL_MIN ,USB_PHY_3P3_VOL_MAX );if (rc) {dev_err (motg->phy.dev,"unable to set voltage level " "for hsusb 3p3\n" ); - goto put_3p3; + goto exit; } rc =regulator_enable (motg->v3p3);if (rc) {dev_err (motg->phy.dev,"unable to enable the hsusb 3p3\n" ); - goto put_3p3; - } - motg->v1p8 =regulator_get (motg->phy.dev,"HSUSB_1p8" ); -if (IS_ERR (motg->v1p8)) { -dev_err (motg->phy.dev,"unable to get hsusb 1p8\n" ); - rc =PTR_ERR (motg->v1p8); - goto disable_3p3; + goto exit; } rc =regulator_set_voltage (motg->v1p8,USB_PHY_1P8_VOL_MIN ,USB_PHY_1P8_VOL_MAX );if (rc) {dev_err (motg->phy.dev,"unable to set voltage level " "for hsusb 1p8\n" ); - goto put_1p8; + goto disable_3p3; } rc =regulator_enable (motg->v1p8);if (rc) {dev_err (motg->phy.dev,"unable to enable the hsusb 1p8\n" ); - goto put_1p8; + goto disable_3p3; }return 0 ; }regulator_disable (motg->v1p8); -put_1p8: -regulator_put (motg->v1p8); disable_3p3:regulator_disable (motg->v3p3); -put_3p3: -regulator_put (motg->v3p3); +exit:return rc; }
@@ -506,7 +480,7 @@ static int msm_otg_suspend(struct msm_otg *motg)clk_disable_unprepare (motg->pclk);clk_disable_unprepare (motg->clk); -if (motg->core_clk) +if (!IS_ERR (motg->core_clk))clk_disable_unprepare (motg->core_clk);if (!IS_ERR (motg->pclk_src))
@@ -546,7 +520,7 @@ static int msm_otg_resume(struct msm_otg *motg)clk_prepare_enable (motg->pclk);clk_prepare_enable (motg->clk); -if (motg->core_clk) +if (!IS_ERR (motg->core_clk))clk_prepare_enable (motg->core_clk); if (motg->pdata->phy_type == SNPS_28NM_INTEGRATED_PHY &&
@@ -1415,37 +1389,34 @@ static int msm_otg_probe(struct platform_device *pdev)return -ENODEV ; } - motg =kzalloc (sizeof (struct msm_otg ),GFP_KERNEL ); + motg =devm_kzalloc (&pdev->dev,sizeof (struct msm_otg ),GFP_KERNEL );if (!motg) {dev_err (&pdev->dev,"unable to allocate msm_otg\n" );return -ENOMEM ; } - motg->phy.otg =kzalloc (sizeof (struct usb_otg ),GFP_KERNEL ); + motg->phy.otg =devm_kzalloc (&pdev->dev,sizeof (struct usb_otg ), +GFP_KERNEL );if (!motg->phy.otg) {dev_err (&pdev->dev,"unable to allocate msm_otg\n" ); - ret = -ENOMEM ; - goto free_motg; +return -ENOMEM ; } motg->pdata =dev_get_platdata (&pdev->dev); phy = &motg->phy; phy->dev = &pdev->dev; - motg->phy_reset_clk =clk_get (&pdev->dev,"usb_phy_clk" ); + motg->phy_reset_clk =devm_clk_get (&pdev->dev,"usb_phy_clk" );if (IS_ERR (motg->phy_reset_clk)) {dev_err (&pdev->dev,"failed to get usb_phy_clk\n" ); - ret =PTR_ERR (motg->phy_reset_clk); - goto free_motg; +return PTR_ERR (motg->phy_reset_clk); } - motg->clk =clk_get (&pdev->dev,"usb_hs_clk" ); + motg->clk =devm_clk_get (&pdev->dev,"usb_hs_clk" );if (IS_ERR (motg->clk)) {dev_err (&pdev->dev,"failed to get usb_hs_clk\n" ); - ret =PTR_ERR (motg->clk); - goto put_phy_reset_clk; +return PTR_ERR (motg->clk); } -clk_set_rate (motg->clk,60000000 );/* * If USB Core is running its protocol engine based on CORE CLK,
@@ -1454,22 +1425,18 @@ static int msm_otg_probe(struct platform_device *pdev)* CORE CLK. For such USB cores, vote for maximum clk frequency * on pclk source */ + motg->pclk_src =ERR_PTR (-ENOENT );if (motg->pdata->pclk_src_name) { - motg->pclk_src =clk_get (&pdev->dev, - motg->pdata->pclk_src_name); + motg->pclk_src =devm_clk_get (&pdev->dev, + motg->pdata->pclk_src_name);if (IS_ERR (motg->pclk_src)) - goto put_clk; -clk_set_rate (motg->pclk_src,INT_MAX ); -clk_prepare_enable (motg->pclk_src); - }else - motg->pclk_src =ERR_PTR (-ENOENT ); - +return PTR_ERR (motg->pclk_src); + } - motg->pclk =clk_get (&pdev->dev,"usb_hs_pclk" ); + motg->pclk =devm_clk_get (&pdev->dev,"usb_hs_pclk" );if (IS_ERR (motg->pclk)) {dev_err (&pdev->dev,"failed to get usb_hs_pclk\n" ); - ret =PTR_ERR (motg->pclk); - goto put_pclk_src; +return PTR_ERR (motg->pclk); }/*
@@ -1477,65 +1444,78 @@ static int msm_otg_probe(struct platform_device *pdev)* clock is introduced to remove the dependency on AXI * bus frequency. */ - motg->core_clk =clk_get (&pdev->dev,"usb_hs_core_clk" ); -if (IS_ERR (motg->core_clk)) - motg->core_clk =NULL ; + motg->core_clk =devm_clk_get (&pdev->dev,"usb_hs_core_clk" ); res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); -if (!res) { -dev_err (&pdev->dev,"failed to get platform resource mem\n" ); - ret = -ENODEV ; - goto put_core_clk; - } + motg->regs =devm_ioremap (&pdev->dev, res->start,resource_size (res)); +if (IS_ERR (motg->regs)) +return PTR_ERR (motg->regs); - motg->regs =ioremap (res->start,resource_size (res)); -if (!motg->regs) { -dev_err (&pdev->dev,"ioremap failed\n" ); - ret = -ENOMEM ; - goto put_core_clk; - }dev_info (&pdev->dev,"OTG regs = %p\n" , motg->regs); motg->irq =platform_get_irq (pdev,0 );if (!motg->irq) {dev_err (&pdev->dev,"platform_get_irq failed\n" ); - ret = -ENODEV ; - goto free_regs; +return motg->irq; + } + + motg->vddcx =devm_regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); +if (IS_ERR (motg->vddcx)) { +dev_err (motg->phy.dev,"unable to get hsusb vddcx\n" ); +return PTR_ERR (motg->vddcx); + } + + motg->v3p3 =devm_regulator_get (motg->phy.dev,"HSUSB_3p3" ); +if (IS_ERR (motg->v3p3)) { +dev_err (motg->phy.dev,"unable to get hsusb 3p3\n" ); +return PTR_ERR (motg->v3p3); + } + + motg->v1p8 =devm_regulator_get (motg->phy.dev,"HSUSB_1p8" ); +if (IS_ERR (motg->v1p8)) { +dev_err (motg->phy.dev,"unable to get hsusb 1p8\n" ); +return PTR_ERR (motg->v1p8); + } + +clk_set_rate (motg->clk,60000000 ); +if (!IS_ERR (motg->pclk_src)) { +clk_set_rate (motg->pclk_src,INT_MAX ); +clk_prepare_enable (motg->pclk_src); }clk_prepare_enable (motg->clk);clk_prepare_enable (motg->pclk); +if (!IS_ERR (motg->core_clk)) +clk_prepare_enable (motg->core_clk); + ret =msm_hsusb_init_vddcx (motg,1 );if (ret) {dev_err (&pdev->dev,"hsusb vddcx configuration failed\n" ); - goto free_regs; + goto disable_clks; } ret =msm_hsusb_ldo_init (motg,1 );if (ret) {dev_err (&pdev->dev,"hsusb vreg configuration failed\n" ); - goto vddcx_exit; + goto disable_vddcx; } ret =msm_hsusb_ldo_set_mode (motg,1 );if (ret) {dev_err (&pdev->dev,"hsusb vreg enable failed\n" ); - goto ldo_exit; + goto disable_ldo; } -if (motg->core_clk) -clk_prepare_enable (motg->core_clk); -writel (0 ,USB_USBINTR );writel (0 ,USB_OTGSC );INIT_WORK (&motg->sm_work, msm_otg_sm_work);INIT_DELAYED_WORK (&motg->chg_work, msm_chg_detect_work); - ret =request_irq (motg->irq, msm_otg_irq,IRQF_SHARED , + ret =devm_request_irq (&pdev->dev, motg->irq, msm_otg_irq,IRQF_SHARED ,"msm_otg" , motg);if (ret) {dev_err (&pdev->dev,"request irq failed\n" ); - goto disable_clks; + goto disable_ldo; } phy->init = msm_otg_reset;
@@ -1550,7 +1530,7 @@ static int msm_otg_probe(struct platform_device *pdev) ret =usb_add_phy (&motg->phy,USB_PHY_TYPE_USB2 );if (ret) {dev_err (&pdev->dev,"usb_add_phy failed\n" ); - goto free_irq; + goto disable_ldo; }platform_set_drvdata (pdev, motg);
@@ -1568,33 +1548,18 @@ static int msm_otg_probe(struct platform_device *pdev)pm_runtime_enable (&pdev->dev);return 0 ; -free_irq: -free_irq (motg->irq, motg); + +disable_ldo: +msm_hsusb_ldo_init (motg,0 ); +disable_vddcx: +msm_hsusb_init_vddcx (motg,0 ); disable_clks:clk_disable_unprepare (motg->pclk);clk_disable_unprepare (motg->clk); -ldo_exit: -msm_hsusb_ldo_init (motg,0 ); -vddcx_exit: -msm_hsusb_init_vddcx (motg,0 ); -free_regs: -iounmap (motg->regs); -put_core_clk: -if (motg->core_clk) -clk_put (motg->core_clk); -clk_put (motg->pclk); -put_pclk_src: -if (!IS_ERR (motg->pclk_src)) { +if (!IS_ERR (motg->core_clk)) +clk_disable_unprepare (motg->core_clk); +if (!IS_ERR (motg->pclk_src))clk_disable_unprepare (motg->pclk_src); -clk_put (motg->pclk_src); - } -put_clk: -clk_put (motg->clk); -put_phy_reset_clk: -clk_put (motg->phy_reset_clk); -free_motg: -kfree (motg->phy.otg); -kfree (motg);return ret; }
@@ -1617,7 +1582,7 @@ static int msm_otg_remove(struct platform_device *pdev)pm_runtime_disable (&pdev->dev);usb_remove_phy (phy); -free_irq (motg->irq, motg); +disable_irq (motg->irq);/* * Put PHY in low power mode.
@@ -1637,26 +1602,15 @@ static int msm_otg_remove(struct platform_device *pdev)clk_disable_unprepare (motg->pclk);clk_disable_unprepare (motg->clk); -if (motg->core_clk) +if (!IS_ERR (motg->core_clk))clk_disable_unprepare (motg->core_clk); -if (!IS_ERR (motg->pclk_src)) { +if (!IS_ERR (motg->pclk_src))clk_disable_unprepare (motg->pclk_src); -clk_put (motg->pclk_src); - } +msm_hsusb_ldo_init (motg,0 ); -iounmap (motg->regs);pm_runtime_set_suspended (&pdev->dev); -clk_put (motg->phy_reset_clk); -clk_put (motg->pclk); -clk_put (motg->clk); -if (motg->core_clk) -clk_put (motg->core_clk); - -kfree (motg->phy.otg); -kfree (motg); -return 0 ; }
--
1.8.3.2
Re: [PATCH v7 05/20] usb: phy: msm: Migrate to Managed Device Resource allocation
Quoted 7 lines · Ivan T. Ivanov
drivers/usb/phy/phy-msm-usb.c +7
-0+ motg->vddcx =devm_regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); +if (IS_ERR (motg->vddcx)) { +dev_err (motg->phy.dev,"unable to get hsusb vddcx\n" ); +return PTR_ERR (motg->vddcx); + } + + motg->v3p3 =devm_regulator_get (motg->phy.dev,"HSUSB_3p3" );
drivers/usb/phy/phy-msm-usb.c static int msm_otg_probe(struct platform_device *pdev) · line 1478
Quoted 10 lines
drivers/usb/phy/phy-msm-usb.c +10
-0+if (IS_ERR (motg->v3p3)) { +dev_err (motg->phy.dev,"unable to get hsusb 3p3\n" ); +return PTR_ERR (motg->v3p3); + } + + motg->v1p8 =devm_regulator_get (motg->phy.dev,"HSUSB_1p8" ); +if (IS_ERR (motg->v1p8)) { +dev_err (motg->phy.dev,"unable to get hsusb 1p8\n" ); +return PTR_ERR (motg->v1p8); + }
It seems that calling devm_regulator_bulk_get() here would simplify the code here.
Re: [PATCH v7 05/20] usb: phy: msm: Migrate to Managed Device Resource allocation
Quoted 14 lines · Fabio Estevam
Quoted 12 lines · Ivan T. Ivanov
drivers/usb/phy/phy-msm-usb.c +12
-0+ motg->vddcx =devm_regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); +if (IS_ERR (motg->vddcx)) { +dev_err (motg->phy.dev,"unable to get hsusb vddcx\n" ); +return PTR_ERR (motg->vddcx); + } + + motg->v3p3 =devm_regulator_get (motg->phy.dev,"HSUSB_3p3" ); +if (IS_ERR (motg->v3p3)) { +dev_err (motg->phy.dev,"unable to get hsusb 3p3\n" ); +return PTR_ERR (motg->v3p3); + } +
Quoted 8 lines
drivers/usb/phy/phy-msm-usb.c static int msm_otg_probe(struct platform_device *pdev) · line 1478
Quoted 5 lines
drivers/usb/phy/phy-msm-usb.c +5
-0+ motg->v1p8 =devm_regulator_get (motg->phy.dev,"HSUSB_1p8" ); +if (IS_ERR (motg->v1p8)) { +dev_err (motg->phy.dev,"unable to get hsusb 1p8\n" ); +return PTR_ERR (motg->v1p8); + }It seems that calling
devm_regulator_bulk_get()here would simplify the code here.
any comments here ?? Should I expect a new version ?
Signature · 1 line
balbi
Re: [PATCH v7 05/20] usb: phy: msm: Migrate to Managed Device Resource allocation
Quoted 15 lines · Felipe Balbi
Quoted 14 lines · Fabio Estevam
Quoted 12 lines · Ivan T. Ivanov
drivers/usb/phy/phy-msm-usb.c +12
-0+ motg->vddcx =devm_regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); +if (IS_ERR (motg->vddcx)) { +dev_err (motg->phy.dev,"unable to get hsusb vddcx\n" ); +return PTR_ERR (motg->vddcx); + } + + motg->v3p3 =devm_regulator_get (motg->phy.dev,"HSUSB_3p3" ); +if (IS_ERR (motg->v3p3)) { +dev_err (motg->phy.dev,"unable to get hsusb 3p3\n" ); +return PTR_ERR (motg->v3p3); + } +
Quoted 8 lines
Quoted 8 lines
drivers/usb/phy/phy-msm-usb.c static int msm_otg_probe(struct platform_device *pdev) · line 1478
Quoted 5 lines
drivers/usb/phy/phy-msm-usb.c +5
-0+ motg->v1p8 =devm_regulator_get (motg->phy.dev,"HSUSB_1p8" ); +if (IS_ERR (motg->v1p8)) { +dev_err (motg->phy.dev,"unable to get hsusb 1p8\n" ); +return PTR_ERR (motg->v1p8); + }It seems that calling
devm_regulator_bulk_get()here would simplify the code here.
Sure.
Quoted 2 lines
any comments here ?? Should I expect a new version ?
Will fix rest of the comments and send updated patch set.
Regards,
Ivan
Quoted 1 line
PATCH v7 6/20 usb: phy: msm: Remove unnecessarily check for valid regulators.
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Whether regulators are available or not is checked at driver probe. If they are not available driver will refuse to load, so no need to check them again.
--- drivers/usb/phy/phy-msm-usb.c | 10 ---------- 1 file changed, 10 deletions(-)
drivers/usb/phy/phy-msm-usb.c +0 -10
@@ -133,16 +133,6 @@ static int msm_hsusb_ldo_set_mode(struct msm_otg *motg, int on) {int ret =0 ; -if (!motg->v1p8 ||IS_ERR (motg->v1p8)) { -pr_err ("%s: HSUSB_1p8 is not initialized\n" , __func__); -return -ENODEV ; - } - -if (!motg->v3p3 ||IS_ERR (motg->v3p3)) { -pr_err ("%s: HSUSB_3p3 is not initialized\n" , __func__); -return -ENODEV ; - } -if (on) { ret =regulator_set_optimum_mode (motg->v1p8,USB_PHY_1P8_HPM_LOAD );
--
1.8.3.2
PATCH v7 7/20 usb: phy: msm: Fix checkpatch.pl warnings
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
This fixes following:
WARNING: quoted string split across lines
WARNING: Prefer seq_puts to seq_printf
--- drivers/usb/phy/phy-msm-usb.c | 39 ++++++++++++++------------------------- 1 file changed, 14 insertions(+), 25 deletions(-)
drivers/usb/phy/phy-msm-usb.c +14 -25
@@ -67,8 +67,7 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)USB_PHY_VDD_DIG_VOL_MIN , USB_PHY_VDD_DIG_VOL_MAX);if (ret) { -dev_err (motg->phy.dev,"unable to set the voltage " -"for hsusb vddcx\n" ); +dev_err (motg->phy.dev,"Cannot set vddcx voltage\n" );return ret; }
@@ -79,8 +78,7 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init) ret =regulator_set_voltage (motg->vddcx,0 ,USB_PHY_VDD_DIG_VOL_MAX );if (ret) -dev_err (motg->phy.dev,"unable to set the voltage " -"for hsusb vddcx\n" ); +dev_err (motg->phy.dev,"Cannot set vddcx voltage\n" ); ret =regulator_disable (motg->vddcx);if (ret)dev_err (motg->phy.dev,"unable to disable hsusb vddcx\n" );
@@ -97,8 +95,7 @@ static int msm_hsusb_ldo_init(struct msm_otg *motg, int init) rc =regulator_set_voltage (motg->v3p3,USB_PHY_3P3_VOL_MIN ,USB_PHY_3P3_VOL_MAX );if (rc) { -dev_err (motg->phy.dev,"unable to set voltage level " -"for hsusb 3p3\n" ); +dev_err (motg->phy.dev,"Cannot set v3p3 voltage\n" ); goto exit; } rc =regulator_enable (motg->v3p3);
@@ -109,8 +106,7 @@ static int msm_hsusb_ldo_init(struct msm_otg *motg, int init) rc =regulator_set_voltage (motg->v1p8,USB_PHY_1P8_VOL_MIN ,USB_PHY_1P8_VOL_MAX );if (rc) { -dev_err (motg->phy.dev,"unable to set voltage level " -"for hsusb 1p8\n" ); +dev_err (motg->phy.dev,"Cannot set v1p8 voltage\n" ); goto disable_3p3; } rc =regulator_enable (motg->v1p8);
@@ -137,15 +133,13 @@ static int msm_hsusb_ldo_set_mode(struct msm_otg *motg, int on) ret =regulator_set_optimum_mode (motg->v1p8,USB_PHY_1P8_HPM_LOAD );if (ret <0 ) { -pr_err ("%s: Unable to set HPM of the regulator " -"HSUSB_1p8\n" , __func__); +pr_err ("Could not set HPM for v1p8\n" );return ret; } ret =regulator_set_optimum_mode (motg->v3p3,USB_PHY_3P3_HPM_LOAD );if (ret <0 ) { -pr_err ("%s: Unable to set HPM of the regulator " -"HSUSB_3p3\n" , __func__); +pr_err ("Could not set HPM for v3p3\n" );regulator_set_optimum_mode (motg->v1p8,USB_PHY_1P8_LPM_LOAD );return ret;
@@ -154,13 +148,11 @@ static int msm_hsusb_ldo_set_mode(struct msm_otg *motg, int on) ret =regulator_set_optimum_mode (motg->v1p8,USB_PHY_1P8_LPM_LOAD );if (ret <0 ) -pr_err ("%s: Unable to set LPM of the regulator " -"HSUSB_1p8\n" , __func__); +pr_err ("Could not set LPM for v1p8\n" ); ret =regulator_set_optimum_mode (motg->v3p3,USB_PHY_3P3_LPM_LOAD );if (ret <0 ) -pr_err ("%s: Unable to set LPM of the regulator " -"HSUSB_3p3\n" , __func__); +pr_err ("Could not set LPM for v3p3\n" ); }pr_debug ("reg (%s)\n" , on ?"HPM" :"LPM" );
@@ -390,8 +382,7 @@ static int msm_hsusb_config_vddcx(struct msm_otg *motg, int high) ret =regulator_set_voltage (motg->vddcx, min_vol, max_vol);if (ret) { -pr_err ("%s: unable to set the voltage for regulator " -"HSUSB_VDDCX\n" , __func__); +pr_err ("Cannot set vddcx voltage\n" );return ret; }
@@ -546,8 +537,7 @@ static int msm_otg_resume(struct msm_otg *motg)* PHY. USB state can not be restored. Re-insertion * of USB cable is the only way to get USB working. */ -dev_err (phy->dev,"Unable to resume USB." -"Re-plugin the cable\n" ); +dev_err (phy->dev,"Unable to resume USB. Re-plugin the cable\n" );msm_otg_reset (phy); }
@@ -1242,13 +1232,13 @@ static int msm_otg_mode_show(struct seq_file *s, void *unused)switch (otg->phy->state) {case OTG_STATE_A_HOST : -seq_printf (s,"host\n" ); +seq_puts (s,"host\n" );break ;case OTG_STATE_B_PERIPHERAL : -seq_printf (s,"peripheral\n" ); +seq_puts (s,"peripheral\n" );break ;default : -seq_printf (s,"none\n" ); +seq_puts (s,"none\n" );break ; }
@@ -1530,8 +1520,7 @@ static int msm_otg_probe(struct platform_device *pdev) motg->pdata->otg_control == OTG_USER_CONTROL) { ret =msm_otg_debugfs_init (motg);if (ret) -dev_dbg (&pdev->dev,"mode debugfs file is" -"not available\n" ); +dev_dbg (&pdev->dev,"Can not create mode change file\n" ); }pm_runtime_set_active (&pdev->dev);
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
PATCH v7 8/20 usb: phy: msm: Replace custom enum usb_mode_type with enum usb_dr_mode
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Use enum usb_dr_mode and drop default usb_dr_mode from platform data.
USB DT bindings states: dr_mode: "...In case this attribute isn't passed via DT, USB DRD controllers should default to OTG...", so remove redundand field.
--- arch/arm/mach-msm/board-msm7x30.c | 2 +- arch/arm/mach-msm/board-qsd8x50.c | 2 +- drivers/usb/phy/phy-msm-usb.c | 41 ++++++++++++++++----------------------- include/linux/usb/msm_hsusb.h | 20 +------------------ 4 files changed, 20 insertions(+), 45 deletions(-)
arch/arm/mach-msm/board-msm7x30.c +1 -1
@@ -95,7 +95,7 @@ static int hsusb_phy_clk_reset(struct clk *phy_clk)static struct msm_otg_platform_data msm_otg_pdata = { .phy_init_seq = hsusb_phy_init_seq, - .mode =USB_PERIPHERAL , + .mode =USB_DR_MODE_PERIPHERAL , .otg_control =OTG_PHY_CONTROL , .link_clk_reset = hsusb_link_clk_reset, .phy_clk_reset = hsusb_phy_clk_reset,
arch/arm/mach-msm/board-qsd8x50.c +1 -1
@@ -116,7 +116,7 @@ static int hsusb_phy_clk_reset(struct clk *phy_clk)static struct msm_otg_platform_data msm_otg_pdata = { .phy_init_seq = hsusb_phy_init_seq, - .mode =USB_PERIPHERAL , + .mode =USB_DR_MODE_PERIPHERAL , .otg_control =OTG_PHY_CONTROL , .link_clk_reset = hsusb_link_clk_reset, .phy_clk_reset = hsusb_phy_clk_reset,
drivers/usb/phy/phy-msm-usb.c +17 -24
129 lines not on this page · raw message
include/linux/usb/msm_hsusb.h +1 -19
@@ -23,21 +23,6 @@#include <linux/clk.h> /** -* Supported USB modes -* -* USB_PERIPHERAL Only peripheral mode is supported. -* USB_HOST Only host mode is supported. -* USB_OTG OTG mode is supported. -* -*/ -enum usb_mode_type { -USB_NONE =0 , -USB_PERIPHERAL , -USB_HOST , -USB_OTG , -}; - -/** * OTG control * * OTG_NO_CONTROL Id/VBUS notifications not required. Useful in host
@@ -121,8 +106,6 @@ enum usb_chg_type {* @power_budget: VBUS power budget in mA (0 will be treated as 500mA). * @mode: Supported mode (OTG/peripheral/host). * @otg_control: OTG switch controlled by user/Id pin -* @default_mode: Default operational mode. Applicable only if -* OTG switch is controller by user. * @pclk_src_name: pclk is derived from ebi1_usb_clk in case of 7x27 and 8k * dfab_usb_hs_clk in case of 8660 and 8960. */
@@ -130,9 +113,8 @@ struct msm_otg_platform_data {int *phy_init_seq;void (*vbus_power)(bool on);unsigned power_budget; -enum usb_mode_type mode; +enum usb_dr_mode mode;enum otg_control_type otg_control; -enum usb_mode_type default_mode;enum msm_usb_phy_type phy_type;void (*setup_gpio)(enum usb_otg_state state);char *pclk_src_name;
--
1.8.3.2
PATCH v7 9/20 usb: phy: msm: Remove unused pclk_src_name
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
There are no references to 'pclk_src_name' in plaform code, so it is unused.
--- drivers/usb/phy/phy-msm-usb.c | 26 +------------------------- include/linux/usb/msm_hsusb.h | 5 ----- 2 files changed, 1 insertion(+), 30 deletions(-)
drivers/usb/phy/phy-msm-usb.c +1 -25
@@ -464,9 +464,6 @@ static int msm_otg_suspend(struct msm_otg *motg)if (!IS_ERR (motg->core_clk))clk_disable_unprepare (motg->core_clk); -if (!IS_ERR (motg->pclk_src)) -clk_disable_unprepare (motg->pclk_src); -if (motg->pdata->phy_type ==SNPS_28NM_INTEGRATED_PHY && motg->pdata->otg_control ==OTG_PMIC_CONTROL ) {msm_hsusb_ldo_set_mode (motg,0 );
@@ -496,9 +493,6 @@ static int msm_otg_resume(struct msm_otg *motg)if (!atomic_read (&motg->in_lpm))return 0 ; -if (!IS_ERR (motg->pclk_src)) -clk_prepare_enable (motg->pclk_src); -clk_prepare_enable (motg->pclk);clk_prepare_enable (motg->clk);if (!IS_ERR (motg->core_clk))
@@ -1395,17 +1389,8 @@ static int msm_otg_probe(struct platform_device *pdev)* If USB Core is running its protocol engine based on CORE CLK, * CORE CLK must be running at >55Mhz for correct HSUSB * operation and USB core cannot tolerate frequency changes on -* CORE CLK. For such USB cores, vote for maximum clk frequency -* on pclk source +* CORE CLK. */ - motg->pclk_src =ERR_PTR (-ENOENT ); -if (motg->pdata->pclk_src_name) { - motg->pclk_src =devm_clk_get (&pdev->dev, - motg->pdata->pclk_src_name); -if (IS_ERR (motg->pclk_src)) -return PTR_ERR (motg->pclk_src); - } - motg->pclk =devm_clk_get (&pdev->dev,"usb_hs_pclk" );if (IS_ERR (motg->pclk)) {dev_err (&pdev->dev,"failed to get usb_hs_pclk\n" );
@@ -1451,10 +1436,6 @@ static int msm_otg_probe(struct platform_device *pdev) }clk_set_rate (motg->clk,60000000 ); -if (!IS_ERR (motg->pclk_src)) { -clk_set_rate (motg->pclk_src,INT_MAX ); -clk_prepare_enable (motg->pclk_src); - }clk_prepare_enable (motg->clk);clk_prepare_enable (motg->pclk);
@@ -1530,8 +1511,6 @@ disable_clks:clk_disable_unprepare (motg->clk);if (!IS_ERR (motg->core_clk))clk_disable_unprepare (motg->core_clk); -if (!IS_ERR (motg->pclk_src)) -clk_disable_unprepare (motg->pclk_src);return ret; }
@@ -1576,9 +1555,6 @@ static int msm_otg_remove(struct platform_device *pdev)clk_disable_unprepare (motg->clk);if (!IS_ERR (motg->core_clk))clk_disable_unprepare (motg->core_clk); -if (!IS_ERR (motg->pclk_src)) -clk_disable_unprepare (motg->pclk_src); -msm_hsusb_ldo_init (motg,0 );pm_runtime_set_suspended (&pdev->dev);
include/linux/usb/msm_hsusb.h +0 -5
@@ -106,8 +106,6 @@ enum usb_chg_type {* @power_budget: VBUS power budget in mA (0 will be treated as 500mA). * @mode: Supported mode (OTG/peripheral/host). * @otg_control: OTG switch controlled by user/Id pin -* @pclk_src_name: pclk is derived from ebi1_usb_clk in case of 7x27 and 8k -* dfab_usb_hs_clk in case of 8660 and 8960. */ struct msm_otg_platform_data {int *phy_init_seq;
@@ -117,7 +115,6 @@ struct msm_otg_platform_data {enum otg_control_type otg_control;enum msm_usb_phy_type phy_type;void (*setup_gpio)(enum usb_otg_state state); -char *pclk_src_name;int (*link_clk_reset)(struct clk *link_clk,bool assert);int (*phy_clk_reset)(struct clk *phy_clk); };
@@ -129,7 +126,6 @@ struct msm_otg_platform_data {* @irq: IRQ number assigned for HSUSB controller. * @clk: clock struct of usb_hs_clk. * @pclk: clock struct of usb_hs_pclk. -* @pclk_src: pclk source for voting. * @phy_reset_clk: clock struct of usb_phy_clk. * @core_clk: clock struct of usb_hs_core_clk. * @regs: ioremapped register base address.
@@ -150,7 +146,6 @@ struct msm_otg {int irq;struct clk *clk;struct clk *pclk; -struct clk *pclk_src;struct clk *phy_reset_clk;struct clk *core_clk;void __iomem *regs;
--
1.8.3.2
PATCH v7 10/20 usb: phy: msm: Remove HSUSB prefix from regulator names
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Prefix did not bring any useful information. Currently none of the MSM platforms define these regulators, so it is safe to rename them.
--- drivers/usb/phy/phy-msm-usb.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/usb/phy/phy-msm-usb.c +3 -3
@@ -1417,19 +1417,19 @@ static int msm_otg_probe(struct platform_device *pdev)return motg->irq; } - motg->vddcx =devm_regulator_get (motg->phy.dev,"HSUSB_VDDCX" ); + motg->vddcx =devm_regulator_get (motg->phy.dev,"vddcx" );if (IS_ERR (motg->vddcx)) {dev_err (motg->phy.dev,"unable to get hsusb vddcx\n" );return PTR_ERR (motg->vddcx); } - motg->v3p3 =devm_regulator_get (motg->phy.dev,"HSUSB_3p3" ); + motg->v3p3 =devm_regulator_get (motg->phy.dev,"v3p3" );if (IS_ERR (motg->v3p3)) {dev_err (motg->phy.dev,"unable to get hsusb 3p3\n" );return PTR_ERR (motg->v3p3); } - motg->v1p8 =devm_regulator_get (motg->phy.dev,"HSUSB_1p8" ); + motg->v1p8 =devm_regulator_get (motg->phy.dev,"v1p8" );if (IS_ERR (motg->v1p8)) {dev_err (motg->phy.dev,"unable to get hsusb 1p8\n" );return PTR_ERR (motg->v1p8);
--
1.8.3.2
PATCH v7 11/20 usb: phy: msm: Properly check result from platform_get_irq()
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Function return negative code on error.
--- drivers/usb/phy/phy-msm-usb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/usb/phy/phy-msm-usb.c +1 -1
@@ -1412,7 +1412,7 @@ static int msm_otg_probe(struct platform_device *pdev)dev_info (&pdev->dev,"OTG regs = %p\n" , motg->regs); motg->irq =platform_get_irq (pdev,0 ); -if (!motg->irq) { +if (motg->irq <0 ) {dev_err (&pdev->dev,"platform_get_irq failed\n" );return motg->irq; }
--
1.8.3.2
PATCH v7 12/20 usb: phy: msm: Add device tree support and binding information
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Allows controller to be specified via device tree.
--- .../devicetree/bindings/usb/msm-hsusb.txt | 67 ++++++++++++ drivers/usb/phy/phy-msm-usb.c | 113 +++++++++++++++++---- include/linux/usb/msm_hsusb.h | 6 +- 3 files changed, 165 insertions(+), 21 deletions(-)
Documentation/devicetree/bindings/usb/msm-hsusb.txt +67 -0
@@ -15,3 +15,70 @@ Example EHCI controller device node: usb-phy = <&usb_otg>; }; +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + };
drivers/usb/phy/phy-msm-usb.c +94 -19
188 lines not on this page · raw message
include/linux/usb/msm_hsusb.h +4 -2
@@ -100,8 +100,9 @@ enum usb_chg_type {/** * struct msm_otg_platform_data - platform device data * for msm_otg driver. -* @phy_init_seq: PHY configuration sequence. val, reg pairs -* terminated by -1. +* @phy_init_seq: PHY configuration sequence values. Value of -1 is reserved as +* "do not overwrite default vaule at this address". +* @phy_init_sz: PHY configuration sequence size. * @vbus_power: VBUS power on/off routine. * @power_budget: VBUS power budget in mA (0 will be treated as 500mA). * @mode: Supported mode (OTG/peripheral/host).
@@ -109,6 +110,7 @@ enum usb_chg_type {*/ struct msm_otg_platform_data {int *phy_init_seq; +int phy_init_sz;void (*vbus_power)(bool on);unsigned power_budget;enum usb_dr_mode mode;
--
1.8.3.2
PATCH v7 13/20 usb: phy: msm: Use reset framework for LINK and PHY resets
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Using reset framework eliminate need of platform specific callbacks and enable reset lines to be specified in DT files.
--- drivers/usb/phy/phy-msm-usb.c | 29 +++++++++++++++++++++-------- include/linux/usb/msm_hsusb.h | 3 +++ 2 files changed, 24 insertions(+), 8 deletions(-)
drivers/usb/phy/phy-msm-usb.c +21 -8
@@ -32,6 +32,7 @@#include <linux/pm_runtime.h> #include <linux/of.h> #include <linux/of_device.h> +#include <linux/reset.h> #include <linux/usb.h> #include <linux/usb/otg.h>
@@ -235,12 +236,15 @@ static void ulpi_init(struct msm_otg *motg)static int msm_otg_link_clk_reset (struct msm_otg *motg,bool assert) { -int ret =0 ; +int ret; -if (!motg->pdata->link_clk_reset) -return ret; +if (motg->pdata->link_clk_reset) + ret = motg->pdata->link_clk_reset (motg->clk, assert); +else if (assert) + ret =reset_control_assert (motg->link_rst); +else + ret =reset_control_deassert (motg->link_rst); - ret = motg->pdata->link_clk_reset (motg->clk, assert);if (ret)dev_err (motg->phy.dev,"usb link clk reset %s failed\n" , assert ?"assert" :"deassert" );
@@ -250,12 +254,13 @@ static int msm_otg_link_clk_reset(struct msm_otg *motg, bool assert)static int msm_otg_phy_clk_reset (struct msm_otg *motg) { -int ret =0 ; +int ret; -if (!motg->pdata->phy_clk_reset) -return ret; +if (motg->pdata->phy_clk_reset) + ret = motg->pdata->phy_clk_reset (motg->phy_reset_clk); +else + ret =reset_control_reset (motg->phy_rst); - ret = motg->pdata->phy_clk_reset (motg->phy_reset_clk);if (ret)dev_err (motg->phy.dev,"usb phy clk reset failed\n" );
@@ -1377,6 +1382,14 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg) id =of_match_device (msm_otg_dt_match, &pdev->dev); pdata->phy_type = (int ) id->data; + motg->link_rst =devm_reset_control_get (&pdev->dev,"link" ); +if (IS_ERR (motg->link_rst)) +return PTR_ERR (motg->link_rst); + + motg->phy_rst =devm_reset_control_get (&pdev->dev,"phy" ); +if (IS_ERR (motg->phy_rst)) +return PTR_ERR (motg->phy_rst); + pdata->mode =of_usb_get_dr_mode (node);if (pdata->mode ==USB_DR_MODE_UNKNOWN ) pdata->mode =USB_DR_MODE_OTG ;
include/linux/usb/msm_hsusb.h +3 -0
@@ -165,6 +165,9 @@ struct msm_otg {struct regulator *v3p3;struct regulator *v1p8;struct regulator *vddcx; + +struct reset_control *phy_rst; + struct reset_control *link_rst; };#endif
--
1.8.3.2
PATCH v7 14/20 usb: phy: msm: Add support for secondary PHY control
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Allow support to use 2nd HSPHY with USB2 Core.
Some platforms may have configuration to allow USB controller work with any of the two HSPHYs present. By default driver configures USB core to use primary HSPHY. Add support to allow user select 2nd HSPHY using DT parameter.
--- .../devicetree/bindings/usb/msm-hsusb.txt | 6 ++++++ drivers/usb/phy/phy-msm-usb.c | 24 ++++++++++++++++++++-- include/linux/usb/msm_hsusb.h | 1 + include/linux/usb/msm_hsusb_hw.h | 1 + 4 files changed, 30 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/usb/msm-hsusb.txt +6 -0
@@ -59,6 +59,12 @@ Optional properties: For example: qcom,phy-init-sequence = < -1 0x63 >; Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. +- qcom,phy-num: Select number of pyco-phy to use, can be one of + 0 - PHY one, default + 1 - Second PHY + Some platforms may have configuration to allow USB + controller work with any of the two HSPHYs present. + Example HSUSB OTG controller device node: usb@f9a55000 {
drivers/usb/phy/phy-msm-usb.c +22 -2
@@ -314,6 +314,9 @@ static int msm_otg_phy_reset(struct msm_otg *motg)if (!retries)return -ETIMEDOUT ; +if (motg->phy_number) +writel (readl (USB_PHY_CTRL2 ) |BIT (16 ),USB_PHY_CTRL2 ); +dev_info (motg->phy.dev,"phy_reset: success\n" );return 0 ; }
@@ -368,6 +371,9 @@ static int msm_otg_reset(struct usb_phy *phy)ulpi_write (phy, ulpi_val,ULPI_USB_INT_EN_FALL ); } +if (motg->phy_number) +writel (readl (USB_PHY_CTRL2 ) |BIT (16 ),USB_PHY_CTRL2 ); +return 0 ; }
@@ -404,6 +410,7 @@ static int msm_otg_suspend(struct msm_otg *motg)struct usb_phy *phy = &motg->phy;struct usb_bus *bus = phy->otg->host;struct msm_otg_platform_data *pdata = motg->pdata; +void __iomem *addr;int cnt =0 ;if (atomic_read (&motg->in_lpm))
@@ -463,9 +470,13 @@ static int msm_otg_suspend(struct msm_otg *motg)*/ writel (readl (USB_USBCMD ) |ASYNC_INTR_CTRL |ULPI_STP_CTRL ,USB_USBCMD ); + addr =USB_PHY_CTRL ; +if (motg->phy_number) + addr =USB_PHY_CTRL2 ; +if (motg->pdata->phy_type ==SNPS_28NM_INTEGRATED_PHY && motg->pdata->otg_control ==OTG_PMIC_CONTROL ) -writel (readl (USB_PHY_CTRL ) |PHY_RETEN ,USB_PHY_CTRL ); +writel (readl (addr) |PHY_RETEN , addr);clk_disable_unprepare (motg->pclk);clk_disable_unprepare (motg->clk);
@@ -495,6 +506,7 @@ static int msm_otg_resume(struct msm_otg *motg) {struct usb_phy *phy = &motg->phy;struct usb_bus *bus = phy->otg->host; +void __iomem *addr;int cnt =0 ;unsigned temp;
@@ -508,9 +520,14 @@ static int msm_otg_resume(struct msm_otg *motg)if (motg->pdata->phy_type ==SNPS_28NM_INTEGRATED_PHY && motg->pdata->otg_control ==OTG_PMIC_CONTROL ) { + + addr =USB_PHY_CTRL ; +if (motg->phy_number) + addr =USB_PHY_CTRL2 ; +msm_hsusb_ldo_set_mode (motg,1 );msm_hsusb_config_vddcx (motg,1 ); -writel (readl (USB_PHY_CTRL ) & ~PHY_RETEN ,USB_PHY_CTRL ); +writel (readl (addr) & ~PHY_RETEN , addr); } temp =readl (USB_USBCMD );
@@ -1399,6 +1416,9 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)if (val ==OTG_PMIC_CONTROL ) pdata->otg_control = val; +if (!of_property_read_u32 (node,"qcom,phy-num" , &val) && val <2 ) + motg->phy_number = val; + prop =of_find_property (node,"qcom,phy-init-sequence" , &len);if (!prop || !len)return 0 ;
include/linux/usb/msm_hsusb.h +1 -0
@@ -158,6 +158,7 @@ struct msm_otg {atomic_t in_lpm;int async_int;unsigned cur_power; +int phy_number;struct delayed_work chg_work;enum usb_chg_state chg_state;enum usb_chg_type chg_type;
include/linux/usb/msm_hsusb_hw.h +1 -0
@@ -25,6 +25,7 @@#define USB_OTGSC (MSM_USB_BASE + 0x01A4)#define USB_USBMODE (MSM_USB_BASE + 0x01A8)#define USB_PHY_CTRL (MSM_USB_BASE + 0x0240) +#define USB_PHY_CTRL2 (MSM_USB_BASE + 0x0278)#define USBCMD_RESET 2#define USB_USBINTR (MSM_USB_BASE + 0x0148)
--
1.8.3.2
PATCH v7 15/20 usb: phy: msm: Correct USB PHY Reset sequence for newer platform
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
On few legacy platforms, USB PHY is having dedicated reset clk. It is used to reset USB PHY after putting USB PHY into low power mode and for calibration of USB PHY. Putting USB PHY into low power mode is causing ulpi read/write timeout as expected. USB PHY reset clk is not available on newer platform.
For 28nm PHY, reset USB PHY after resestting USB LINK. Also reset USB PHY using USB_PHY_PON bit with USB_OTG_HS_PHY_CTRL register after programming USB PHY Override registers as suggested with hardware programming guidelines.
--- drivers/usb/phy/phy-msm-usb.c | 140 ++++++++++++++++++++++++--------------- include/linux/usb/msm_hsusb_hw.h | 5 ++ 2 files changed, 93 insertions(+), 52 deletions(-)
drivers/usb/phy/phy-msm-usb.c +88 -52
@@ -48,6 +48,7 @@#define DRIVER_NAME "msm_otg"#define ULPI_IO_TIMEOUT_USEC (10 * 1000) +#define LINK_RESET_TIMEOUT_USEC (250 * 1000)#define USB_PHY_3P3_VOL_MIN 3050000/* uV */ #define USB_PHY_3P3_VOL_MAX 3300000/* uV */
@@ -267,77 +268,35 @@ static int msm_otg_phy_clk_reset(struct msm_otg *motg)return ret; } -static int msm_otg_phy_reset (struct msm_otg *motg) +static int msm_link_reset (struct msm_otg *motg) {u32 val;int ret; -int retries; ret =msm_otg_link_clk_reset (motg,1 );if (ret)return ret; - ret =msm_otg_phy_clk_reset (motg); -if (ret) -return ret; - ret =msm_otg_link_clk_reset (motg,0 ); -if (ret) -return ret; - val =readl (USB_PORTSC ) & ~PORTSC_PTS_MASK ; -writel (val |PORTSC_PTS_ULPI ,USB_PORTSC ); - -for (retries =3 ; retries >0 ; retries--) { - ret =ulpi_write (&motg->phy,ULPI_FUNC_CTRL_SUSPENDM , -ULPI_CLR (ULPI_FUNC_CTRL )); -if (!ret) -break ; - ret =msm_otg_phy_clk_reset (motg); -if (ret) -return ret; - } -if (!retries) -return -ETIMEDOUT ; +/* wait for 1ms delay as suggested in HPG. */ +usleep_range (1000 ,1200 ); -/* This reset calibrates the phy, if the above write succeeded */ - ret =msm_otg_phy_clk_reset (motg); + ret =msm_otg_link_clk_reset (motg,0 );if (ret)return ret; -for (retries =3 ; retries >0 ; retries--) { - ret =ulpi_read (&motg->phy,ULPI_DEBUG ); -if (ret != -ETIMEDOUT ) -break ; - ret =msm_otg_phy_clk_reset (motg); -if (ret) -return ret; - } -if (!retries) -return -ETIMEDOUT ; -if (motg->phy_number)writel (readl (USB_PHY_CTRL2 ) |BIT (16 ),USB_PHY_CTRL2 ); -dev_info (motg->phy.dev,"phy_reset: success\n" ); + val =readl (USB_PORTSC ) & ~PORTSC_PTS_MASK ; +writel (val |PORTSC_PTS_ULPI ,USB_PORTSC ); +return 0 ; } -#define LINK_RESET_TIMEOUT_USEC (250 * 1000)static int msm_otg_reset (struct usb_phy *phy) { struct msm_otg *motg = container_of(phy, struct msm_otg, phy); -struct msm_otg_platform_data *pdata = motg->pdata;int cnt =0 ; -int ret; -u32 val =0 ; -u32 ulpi_val =0 ; - - ret =msm_otg_phy_reset (motg); -if (ret) { -dev_err (phy->dev,"phy_reset failed\n" ); -return ret; - } - -ulpi_init (motg);writel (USBCMD_RESET ,USB_USBCMD );while (cnt <LINK_RESET_TIMEOUT_USEC ) {
@@ -351,11 +310,86 @@ static int msm_otg_reset(struct usb_phy *phy)/* select ULPI phy */ writel (0x80000000 ,USB_PORTSC ); +writel (0x0 ,USB_AHBBURST ); +writel (0x08 ,USB_AHBMODE ); + +if (motg->phy_number) +writel (readl (USB_PHY_CTRL2 ) |BIT (16 ),USB_PHY_CTRL2 ); +return 0 ; +} + +static void msm_phy_reset (struct msm_otg *motg) +{ +void __iomem *addr; + +if (motg->pdata->phy_type !=SNPS_28NM_INTEGRATED_PHY ) { +msm_otg_phy_clk_reset (motg); +return ; + } + + addr =USB_PHY_CTRL ; +if (motg->phy_number) + addr =USB_PHY_CTRL2 ; + +/* Assert USB PHY_POR */ +writel (readl (addr) |PHY_POR_ASSERT , addr); + +/* +* wait for minimum 10 microseconds as suggested in HPG. +* Use a slightly larger value since the exact value didn't +* work 100% of the time. +*/ +udelay (12 ); + +/* Deassert USB PHY_POR */ +writel (readl (addr) & ~PHY_POR_ASSERT , addr); +} + +static int msm_usb_reset (struct usb_phy *phy) +{ + struct msm_otg *motg = container_of(phy, struct msm_otg, phy); +int ret; + +if (!IS_ERR (motg->core_clk)) +clk_prepare_enable (motg->core_clk); + + ret =msm_link_reset (motg); +if (ret) { +dev_err (phy->dev,"phy_reset failed\n" ); +return ret; + } + + ret =msm_otg_reset (&motg->phy); +if (ret) { +dev_err (phy->dev,"link reset failed\n" ); +return ret; + }msleep (100 ); -writel (0x0 ,USB_AHBBURST ); -writel (0x00 ,USB_AHBMODE ); +/* Reset USB PHY after performing USB Link RESET */ +msm_phy_reset (motg); + +if (!IS_ERR (motg->core_clk)) +clk_disable_unprepare (motg->core_clk); + +return 0 ; +} + +static int msm_phy_init (struct usb_phy *phy) +{ + struct msm_otg *motg = container_of(phy, struct msm_otg, phy); +struct msm_otg_platform_data *pdata = motg->pdata; +u32 val, ulpi_val =0 ; + +/* Program USB PHY Override registers. */ +ulpi_init (motg); + +/* +* It is recommended in HPG to reset USB PHY after programming +* USB PHY Override registers. +*/ +msm_phy_reset (motg);if (pdata->otg_control ==OTG_PHY_CONTROL ) { val =readl (USB_OTGSC );
@@ -1579,7 +1613,7 @@ static int msm_otg_probe(struct platform_device *pdev) goto disable_ldo; } - phy->init = msm_otg_reset; + phy->init = msm_phy_init; phy->set_power = msm_otg_set_power; phy->io_ops = &msm_otg_io_ops;
@@ -1588,6 +1622,8 @@ static int msm_otg_probe(struct platform_device *pdev) phy->otg->set_host = msm_otg_set_host; phy->otg->set_peripheral = msm_otg_set_peripheral; +msm_usb_reset (phy); + ret =usb_add_phy (&motg->phy,USB_PHY_TYPE_USB2 );if (ret) {dev_err (&pdev->dev,"usb_add_phy failed\n" );
include/linux/usb/msm_hsusb_hw.h +5 -0
@@ -42,9 +42,14 @@#define ULPI_DATA (n) ((n) & 255)#define ULPI_DATA_READ (n) (((n) >> 8) & 255) +/* synopsys 28nm phy registers */ +#define ULPI_PWR_CLK_MNG_REG 0x88 +#define OTG_COMP_DISABLE BIT(0) +#define ASYNC_INTR_CTRL (1 << 29)/* Enable async interrupt */ #define ULPI_STP_CTRL (1 << 30)/* Block communication with PHY */ #define PHY_RETEN (1 << 1)/* PHY retention enable/disable */ +#define PHY_POR_ASSERT (1 << 0)/* USB2 28nm PHY POR ASSERT */ /* OTG definitions */ #define OTGSC_INTSTS_MASK (0x7f << 16)
--
1.8.3.2
PATCH v7 16/20 usb: phy: msm: Fix PTS definitions for MSM USB controller
In reply to Ivan T. IvanovFrom: Tim Bird <[email protected]>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB controller. This is a standard chipidea PORTSC definition, where a PHY_TYPE of 10b (<<30) is ULPI and 11b (<<30) is SERIAL. Fix the definitions and use them correctly in the driver code.
--- drivers/usb/phy/phy-msm-usb.c | 8 +++++--- include/linux/usb/msm_hsusb_hw.h | 5 +++-- 2 files changed, 8 insertions(+), 5 deletions(-)
drivers/usb/phy/phy-msm-usb.c +5 -3
@@ -287,8 +287,9 @@ static int msm_link_reset(struct msm_otg *motg)if (motg->phy_number)writel (readl (USB_PHY_CTRL2 ) |BIT (16 ),USB_PHY_CTRL2 ); +/* put transceiver in serial mode as part of reset */ val =readl (USB_PORTSC ) & ~PORTSC_PTS_MASK ; -writel (val |PORTSC_PTS_ULPI ,USB_PORTSC ); +writel (val |PORTSC_PTS_SERIAL ,USB_PORTSC );return 0 ; }
@@ -308,8 +309,9 @@ static int msm_otg_reset(struct usb_phy *phy)if (cnt >=LINK_RESET_TIMEOUT_USEC )return -ETIMEDOUT ; -/* select ULPI phy */ -writel (0x80000000 ,USB_PORTSC ); +/* select ULPI phy and clear other status/control bits in PORTSC */ +writel (PORTSC_PTS_ULPI ,USB_PORTSC ); +writel (0x0 ,USB_AHBBURST );writel (0x08 ,USB_AHBMODE );
include/linux/usb/msm_hsusb_hw.h +3 -2
@@ -31,8 +31,9 @@#define USB_USBINTR (MSM_USB_BASE + 0x0148)#define PORTSC_PHCD (1 << 23)/* phy suspend mode */ -#define PORTSC_PTS_MASK (3 << 30) -#define PORTSC_PTS_ULPI (3 << 30) +#define PORTSC_PTS_MASK (3 << 30) +#define PORTSC_PTS_ULPI (2 << 30) +#define PORTSC_PTS_SERIAL (3 << 30)#define USB_ULPI_VIEWPORT (MSM_USB_BASE + 0x0170)#define ULPI_RUN (1 << 30)
--
1.8.3.2
Re: [PATCH v7 16/20] usb: phy: msm: Fix PTS definitions for MSM USB controller
Quoted 8 lines · Ivan T. Ivanov
From: Tim Bird <[email protected]>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB controller. This is a standard chipidea PORTSC definition, where a
PHY_TYPEof 10b (<<30) is ULPI and 11b (<<30) is SERIAL. Fix the definitions and use them correctly in the driver code.Signed-off-by Tim Bird <tim.bird-/[email protected]>
since you're the one sending the patch, you must add your signed-off-by too. If you reply with your SoB I'll add to proper patches.
Signature · 1 line
balbi
Re: [PATCH v7 16/20] usb: phy: msm: Fix PTS definitions for MSM USB controller
Sent from my Sony Xperia™ smartphone
---- Felipe Balbi wrote ----
Quoted 15 lines · Ivan T. Ivanov
Quoted 8 lines
From: Tim Bird <[email protected]>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB controller. This is a standard chipidea PORTSC definition, where a
PHY_TYPEof 10b (<<30) is ULPI and 11b (<<30) is SERIAL. Fix the definitions and use them correctly in the driver code.Signed-off-by Tim Bird <[email protected]>since you're the one sending the patch, you must add your signed-off-by too. If you reply with your SoB I'll add to proper patches.
Signature · 1 line
balbi
Re: [PATCH v7 16/20] usb: phy: msm: Fix PTS definitions for MSM USB controller
Hi,
Quoted 1 line · Tim
Signed-off-by Tim Bird <[email protected]>
thanks Tim but I already had your SoB in the patch, I need Ivan's :-)
Quoted 17 lines
Sent from my Sony Xperia™ smartphone
---- Felipe Balbi wrote ----
Quoted 12 lines · Ivan T. Ivanov
Quoted 8 lines
From: Tim Bird <[email protected]>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB controller. This is a standard chipidea PORTSC definition, where a
PHY_TYPEof 10b (<<30) is ULPI and 11b (<<30) is SERIAL. Fix the definitions and use them correctly in the driver code.Signed-off-by Tim Bird <[email protected]>since you're the one sending the patch, you must add your signed-off-by too. If you reply with your SoB I'll add to proper patches.
Signature · 1 line
balbi
Re: [PATCH v7 16/20] usb: phy: msm: Fix PTS definitions for MSM USB controller
In reply to Felipe BalbiQuoted 8 lines · Felipe Balbi
Quoted 7 lines · Ivan T. Ivanov
From: Tim Bird <[email protected]>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB controller. This is a standard chipidea PORTSC definition, where a
PHY_TYPEof 10b (<<30) is ULPI and 11b (<<30) is SERIAL. Fix the definitions and use them correctly in the driver code.
Quoted 5 lines
Quoted 1 line
Signed-off-by Tim Bird <[email protected]>since you're the one sending the patch, you must add your signed-off-by too. If you reply with your SoB I'll add to proper patches.
Sure.
Thanks.
Re: [PATCH v7 16/20] usb: phy: msm: Fix PTS definitions for MSM USB controller
Quoted 11 lines · Ivan T. Ivanov
Quoted 10 lines · Felipe Balbi
Quoted 8 lines · Ivan T. Ivanov
From: Tim Bird <[email protected]>
Fix the value used for Parallel Transceiver Select (PTS) for the MSM USB controller. This is a standard chipidea PORTSC definition, where a
PHY_TYPEof 10b (<<30) is ULPI and 11b (<<30) is SERIAL. Fix the definitions and use them correctly in the driver code.Signed-off-by Tim Bird <[email protected]>
Quoted 7 lines
Quoted 3 lines
since you're the one sending the patch, you must add your signed-off-by too. If you reply with your SoB I'll add to proper patches.
Sure.
Signed-of-by Ivan T. Ivanov <[email protected]>
Thanks, I also need you to SoB the other patch from Tim.
Signature · 1 line
balbi
PATCH v7 17/20 usb: phy: msm: Select secondary PHY via TCSR
In reply to Ivan T. IvanovFrom: Tim Bird <[email protected]>
Select the secondary PHY using the TCSR register, if phy-num=1 in the DTS (or phy_number is set in the platform data). The SOC has 2 PHYs which can be used with the OTG port, and this code allows configuring the correct one.
Note: This resolves the problem I was seeing where I couldn't get the USB driver working at all on a dragonboard, from cold boot. This patch depends on patch 5/14 from Ivan's msm USB patch set. It does not use DT for the register address, as there's no evidence that this address changes between SoC versions.
--- drivers/usb/phy/phy-msm-usb.c | 14 ++++++++++++++ include/linux/usb/msm_hsusb_hw.h | 3 +++ 2 files changed, 17 insertions(+)
drivers/usb/phy/phy-msm-usb.c +14 -0
@@ -1488,6 +1488,7 @@ static int msm_otg_probe(struct platform_device *pdev)struct resource *res;struct msm_otg *motg;struct usb_phy *phy; +void __iomem *phy_select; motg =devm_kzalloc (&pdev->dev,sizeof (struct msm_otg ),GFP_KERNEL );if (!motg) {
@@ -1552,6 +1553,19 @@ static int msm_otg_probe(struct platform_device *pdev)if (IS_ERR (motg->regs))return PTR_ERR (motg->regs); +/* +* NOTE: The PHYs can be multiplexed between the chipidea controller +* and the dwc3 controller, using a single bit. It is important that +* the dwc3 driver does not set this bit in an incompatible way. +*/ +if (motg->phy_number) { + phy_select =devm_ioremap_nocache (&pdev->dev,USB2_PHY_SEL ,4 ); +if (IS_ERR (phy_select)) +return PTR_ERR (phy_select); +/* Enable second PHY with the OTG port */ +writel_relaxed (0x1 , phy_select); + } +dev_info (&pdev->dev,"OTG regs = %p\n" , motg->regs); motg->irq =platform_get_irq (pdev,0 );
include/linux/usb/msm_hsusb_hw.h +3 -0
@@ -16,6 +16,9 @@#ifndef __LINUX_USB_GADGET_MSM72K_UDC_H__#define __LINUX_USB_GADGET_MSM72K_UDC_H__ +/* USB phy selector - in TCSR address range */ +#define USB2_PHY_SEL 0xfd4ab000 +#define USB_AHBBURST (MSM_USB_BASE + 0x0090)#define USB_AHBMODE (MSM_USB_BASE + 0x0098)#define USB_CAPLENGTH (MSM_USB_BASE + 0x0100)/* 8 bit */
--
1.8.3.2
PATCH v7 18/20 usb: phy: msm: Handle disconnect events
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
Put the transceiver in non-driving mode. Otherwise host may not detect soft-disconnection.
--- drivers/usb/phy/phy-msm-usb.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
drivers/usb/phy/phy-msm-usb.c +18 -0
@@ -235,6 +235,23 @@ static void ulpi_init(struct msm_otg *motg) } } +static int msm_phy_notify_disconnect (struct usb_phy *phy, +enum usb_device_speed speed) +{ +int val; + +/* +* Put the transceiver in non-driving mode. Otherwise host +* may not detect soft-disconnection. +*/ + val =ulpi_read (phy,ULPI_FUNC_CTRL ); + val &= ~ULPI_FUNC_CTRL_OPMODE_MASK ; + val |=ULPI_FUNC_CTRL_OPMODE_NONDRIVING ; +ulpi_write (phy, val,ULPI_FUNC_CTRL ); + +return 0 ; +} +static int msm_otg_link_clk_reset (struct msm_otg *motg,bool assert) {int ret;
@@ -1631,6 +1648,7 @@ static int msm_otg_probe(struct platform_device *pdev) phy->init = msm_phy_init; phy->set_power = msm_otg_set_power; + phy->notify_disconnect = msm_phy_notify_disconnect; phy->io_ops = &msm_otg_io_ops;
--
1.8.3.2
PATCH v7 19/20 usb: phy: msm: Vote for corner of VDD CX instead of voltage of VDD CX
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
New platform uses RBCPR hardware feature, with that voting for absolute voltage of VDD CX is not required. Hence vote for corner of VDD CX which uses nominal corner voltage on VDD CX.
--- .../devicetree/bindings/usb/msm-hsusb.txt | 5 ++++ drivers/usb/phy/phy-msm-usb.c | 35 +++++++++++++++++----- include/linux/usb/msm_hsusb.h | 1 + 3 files changed, 33 insertions(+), 8 deletions(-)
Documentation/devicetree/bindings/usb/msm-hsusb.txt +5 -0
@@ -65,6 +65,10 @@ Optional properties: Some platforms may have configuration to allow USB controller work with any of the two HSPHYs present. +- qcom,vdd-levels: This property must be a list of three integer values + (no, min, max) where each value represents either a voltage + in microvolts or a value corresponding to voltage corner. + Example HSUSB OTG controller device node: usb@f9a55000 {
@@ -87,4 +91,5 @@ Example HSUSB OTG controller device node: qcom,otg-control = <1>; qcom,phy-init-sequence = < -1 0x63 >; + qcom,vdd-levels = <1 5 7>; };
drivers/usb/phy/phy-msm-usb.c +27 -8
@@ -62,6 +62,13 @@#define USB_PHY_VDD_DIG_VOL_MIN 1000000/* uV */ #define USB_PHY_VDD_DIG_VOL_MAX 1320000/* uV */ +#define USB_PHY_SUSP_DIG_VOL 500000/* uV */ + +enum vdd_levels { +VDD_LEVEL_NONE =0 , +VDD_LEVEL_MIN , +VDD_LEVEL_MAX , +};static int msm_hsusb_init_vddcx (struct msm_otg *motg,int init) {
@@ -69,8 +76,8 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)if (init) { ret =regulator_set_voltage (motg->vddcx, -USB_PHY_VDD_DIG_VOL_MIN , -USB_PHY_VDD_DIG_VOL_MAX ); + motg->vdd_levels[VDD_LEVEL_MIN ], + motg->vdd_levels[VDD_LEVEL_MAX ]);if (ret) {dev_err (motg->phy.dev,"Cannot set vddcx voltage\n" );return ret;
@@ -81,7 +88,7 @@ static int msm_hsusb_init_vddcx(struct msm_otg *motg, int init)dev_err (motg->phy.dev,"unable to enable hsusb vddcx\n" ); }else { ret =regulator_set_voltage (motg->vddcx,0 , -USB_PHY_VDD_DIG_VOL_MAX ); + motg->vdd_levels[VDD_LEVEL_MAX ]);if (ret)dev_err (motg->phy.dev,"Cannot set vddcx voltage\n" ); ret =regulator_disable (motg->vddcx);
@@ -435,17 +442,16 @@ static int msm_phy_init(struct usb_phy *phy)#ifdef CONFIG_PM -#define USB_PHY_SUSP_DIG_VOL 500000static int msm_hsusb_config_vddcx (struct msm_otg *motg,int high) { -int max_vol =USB_PHY_VDD_DIG_VOL_MAX ; +int max_vol = motg->vdd_levels[VDD_LEVEL_MAX ];int min_vol;int ret;if (high) - min_vol =USB_PHY_VDD_DIG_VOL_MIN ; + min_vol = motg->vdd_levels[VDD_LEVEL_MIN ];else - min_vol =USB_PHY_SUSP_DIG_VOL ; + min_vol = motg->vdd_levels[VDD_LEVEL_NONE ]; ret =regulator_set_voltage (motg->vddcx, min_vol, max_vol);if (ret) {
@@ -1441,7 +1447,7 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)struct device_node *node = pdev->dev.of_node;struct property *prop;int len, ret, words; -u32 val; +u32 val, tmp[3 ]; pdata =devm_kzalloc (&pdev->dev,sizeof (*pdata),GFP_KERNEL );if (!pdata)
@@ -1472,6 +1478,19 @@ static int msm_otg_read_dt(struct platform_device *pdev, struct msm_otg *motg)if (!of_property_read_u32 (node,"qcom,phy-num" , &val) && val <2 ) motg->phy_number = val; + motg->vdd_levels[VDD_LEVEL_NONE ] =USB_PHY_SUSP_DIG_VOL ; + motg->vdd_levels[VDD_LEVEL_MIN ] =USB_PHY_VDD_DIG_VOL_MIN ; + motg->vdd_levels[VDD_LEVEL_MAX ] =USB_PHY_VDD_DIG_VOL_MAX ; + +if (of_get_property (node,"qcom,vdd-levels" , &len) && + len ==sizeof (tmp)) { +of_property_read_u32_array (node,"qcom,vdd-levels" , + tmp, len /sizeof (*tmp)); + motg->vdd_levels[VDD_LEVEL_NONE ] = tmp[VDD_LEVEL_NONE ]; + motg->vdd_levels[VDD_LEVEL_MIN ] = tmp[VDD_LEVEL_MIN ]; + motg->vdd_levels[VDD_LEVEL_MAX ] = tmp[VDD_LEVEL_MAX ]; + } + prop =of_find_property (node,"qcom,phy-init-sequence" , &len);if (!prop || !len)return 0 ;
include/linux/usb/msm_hsusb.h +1 -0
@@ -169,6 +169,7 @@ struct msm_otg {struct reset_control *phy_rst;struct reset_control *link_rst; + int vdd_levels[3]; };#endif
--
1.8.3.2
PATCH v7 20/20 usb: phy: msm: Use usb_add_phy_dev() to register device
In reply to Ivan T. IvanovFrom: "Ivan T. Ivanov" <[email protected]>
They could be more than one USB2.0 PHY's on the platform. This will allow all of them to be registred successfuly.
--- drivers/usb/phy/phy-msm-usb.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/usb/phy/phy-msm-usb.c +2 -1
@@ -1668,6 +1668,7 @@ static int msm_otg_probe(struct platform_device *pdev) phy->init = msm_phy_init; phy->set_power = msm_otg_set_power; phy->notify_disconnect = msm_phy_notify_disconnect; + phy->type =USB_PHY_TYPE_USB2 ; phy->io_ops = &msm_otg_io_ops;
@@ -1677,7 +1678,7 @@ static int msm_otg_probe(struct platform_device *pdev)msm_usb_reset (phy); - ret =usb_add_phy (&motg->phy,USB_PHY_TYPE_USB2 ); + ret =usb_add_phy_dev (&motg->phy);if (ret) {dev_err (&pdev->dev,"usb_add_phy failed\n" ); goto disable_ldo;
--
1.8.3.2
Re: [PATCH v7 20/20] usb: phy: msm: Use usb_add_phy_dev() to register device
Hello.
Quoted 3 lines · Ivan T. Ivanov
From: "Ivan T. Ivanov" <[email protected]>
They could be more than one USB2.0 PHY's on the platform.
s/They/There/
Quoted 1 line
This will allow all of them to be registred successfuly.
s/registred successfuly/registered successfully/
Quoted 1 line
Signed-off-by Ivan T. Ivanov <[email protected]>
WBR, Sergei
Re: [PATCH v7 20/20] usb: phy: msm: Use usb_add_phy_dev() to register device
Quoted 6 lines · Sergei Shtylyov
Hello.
Quoted 1 line · Ivan T. Ivanov
From: "Ivan T. Ivanov" <[email protected]>
Quoted 9 lines
Quoted 1 line
They could be more than one USB2.0 PHY's on the platform.
s/They/There/
Quoted 1 line
This will allow all of them to be registred successfuly.
s/registred successfuly/registered successfully/
Quoted 1 line
Signed-off-by Ivan T. Ivanov <[email protected]>
how about here ?
Signature · 1 line
balbi
Re: [PATCH v7 20/20] usb: phy: msm: Use usb_add_phy_dev() to register device
Quoted 7 lines · Felipe Balbi
Quoted 6 lines · Sergei Shtylyov
Hello.
Quoted 1 line · Ivan T. Ivanov
From: "Ivan T. Ivanov" <[email protected]>
Quoted 7 lines
Quoted 7 lines
Quoted 1 line
They could be more than one USB2.0 PHY's on the platform.
s/They/There/
Quoted 1 line
This will allow all of them to be registred successfuly.
s/registred successfuly/registered successfully/
Ouch. will fix it.
Regards,
Ivan