ALSA: usb-audio: work around corrupted TEAC UD-H01 feedback data

From: Clemens Ladisch <[email protected]>

The TEAC UD-H01 firmware sends wrong feedback frequency values, thus causing the PC to send the samples at a wrong rate, which results in clicks and crackles in the output.

Add a workaround to detect and fix the corruption.

Signed-off-by Clemens Ladisch <[email protected]>

[[email protected]: use sender->udh01_fb_quirk rather than
ep->udh01_fb_quirk in snd_usb_handle_sync_urb()]

Reported-and-tested-by Mick <[email protected]>

Reported-and-tested-by Andrea Messa <[email protected]>

Cc <[email protected]>

---
Clemens, I hope you're ok that I resend this patch. With Mick's minor amendment (use sender->udh01_fb_quirk rather than ep->udh01_fb_quirk), Andrea Messa also reported success with the same hardware model.

Thanks,
Daniel

 sound/usb/card.h     |  1 +
 sound/usb/endpoint.c | 15 ++++++++++++++-
 2 files changed, 15 insertions(+), 1 deletion(-)

sound/usb/card.h +1 -0

index 9867ab8..97acb90 100644
@@ -92,6 +92,7 @@ struct snd_usb_endpoint {
 	unsigned int curframesize;      /* current packet size in frames (for capture) */
 	unsigned int syncmaxsize;	/* sync endpoint packet size */
 	unsigned int fill_max:1;	/* fill max packet size always */
+	unsigned int udh01_fb_quirk:1;	/* corrupted feedback data */
 	unsigned int datainterval;      /* log_2 of data packet interval */
 	unsigned int syncinterval;	/* P for adaptive mode, 0 otherwise */
 	unsigned char silence_value;

sound/usb/endpoint.c +14 -1

index e70a87e..289f582 100644
@@ -471,6 +471,10 @@ struct snd_usb_endpoint *snd_usb_add_endpoint(struct snd_usb_audio *chip,
 			ep->syncinterval = 3;
 
 		ep->syncmaxsize = le16_to_cpu(get_endpoint(alts, 1)->wMaxPacketSize);
+
+		if (chip->usb_id == USB_ID(0x0644, 0x8038) /* TEAC UD-H01 */ &&
+		    ep->syncmaxsize == 4)
+			ep->udh01_fb_quirk = 1;
 	}
 
 	list_add_tail(&ep->list, &chip->ep_list);

@@ -1105,7 +1109,16 @@ void snd_usb_handle_sync_urb(struct snd_usb_endpoint *ep,
 	if (f == 0)
 		return;
 
-	if (unlikely(ep->freqshift == INT_MIN)) {
+	if (unlikely(sender->udh01_fb_quirk)) {
+		/*
+		 * The TEAC UD-H01 firmware sometimes changes the feedback value
+		 * by +/- 0x1.0000.
+		 */
+		if (f < ep->freqn - 0x8000)
+			f += 0x10000;
+		else if (f > ep->freqn + 0x8000)
+			f -= 0x10000;
+	} else if (unlikely(ep->freqshift == INT_MIN)) {
 		/*
 		 * The first time we see a feedback value, determine its format
 		 * by shifting it left or right until it matches the nominal

Signature · 1 line

1.9.0