gic: preserve gic V2 bypass bits in cpu ctrl register
Subsystems (2)
PATCH v4 1/1 gic: preserve gic V2 bypass bits in cpu ctrl register
This change is made to preserve the GIC v2 bypass bits in the GIC_CPU_CTRL register (also known as the GICC_CTLR register in spec). This code will preserve all bits configured by the bootload regarding v2 bypass group bits. In the X-Gene platform (as well others), the bypass functionality is not generally used and bypass bits should not be changed by the kernel gic code as it could lead to incorrect behavior. Tested on X-Gene mustang board.
---
V4: Change to use bypass mask, change to use more suitable variable name.
V3: Fix code not touch other bits other than bypass bits.
drivers/irqchip/irq-gic.c | 20 +++++++++++++++++--- 1 files changed, 17 insertions(+), 3 deletions(-)
drivers/irqchip/irq-gic.c +17 -3
@@ -97,6 +97,8 @@ struct irq_chip gic_arch_extn = {#define MAX_GIC_NR 1#endif +#define GIC_BYPASS_MASK 0x1e0 +static struct gic_chip_data gic_data[MAX_GIC_NR ]__read_mostly ;#ifdef CONFIG_GIC_NON_BANKED
@@ -418,6 +420,7 @@ static void gic_cpu_init(struct gic_chip_data *gic)void __iomem *dist_base =gic_data_dist_base (gic);void __iomem *base =gic_data_cpu_base (gic);unsigned int cpu_mask, cpu =smp_processor_id (); +unsigned int bypass;int i;/*
@@ -449,13 +452,20 @@ static void gic_cpu_init(struct gic_chip_data *gic)writel_relaxed (0xa0a0a0a0 , dist_base +GIC_DIST_PRI + i *4 /4 );writel_relaxed (0xf0 , base +GIC_CPU_PRIMASK ); -writel_relaxed (1 , base +GIC_CPU_CTRL ); + + bypass =readl (base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass |0x1 , base +GIC_CPU_CTRL ); }void gic_cpu_if_down (void ) {void __iomem *cpu_base =gic_data_cpu_base (&gic_data[0 ]); -writel_relaxed (0 , cpu_base +GIC_CPU_CTRL ); +unsigned int bypass; + + bypass =readl (cpu_base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass, cpu_base +GIC_CPU_CTRL ); }#ifdef CONFIG_CPU_PM
@@ -566,6 +576,7 @@ static void gic_cpu_restore(unsigned int gic_nr) {int i;u32 *ptr; +unsigned int bypass;void __iomem *dist_base;void __iomem *cpu_base;
@@ -590,7 +601,10 @@ static void gic_cpu_restore(unsigned int gic_nr)writel_relaxed (0xa0a0a0a0 , dist_base +GIC_DIST_PRI + i *4 );writel_relaxed (0xf0 , cpu_base +GIC_CPU_PRIMASK ); -writel_relaxed (1 , cpu_base +GIC_CPU_CTRL ); + + bypass =readl (cpu_base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass |0x1 , cpu_base +GIC_CPU_CTRL ); }static int gic_notifier (struct notifier_block *self,unsigned long cmd,void *v)
Signature · 1 line
1.7.6.1
Quoted 3 lines · Feng Kan
This change is made to preserve the GIC v2 bypass bits in the
GIC_CPU_CTRLregister (also known as theGICC_CTLRregister in spec). This code will preserve all bits configured by the bootload regarding
bootloader
Quoted 1 line
v2 bypass group bits. In the X-Gene platform (as well others), the
Which other platform? It'd be interesting to know which one, as you're implying they haven't managed to boot a mainline kernel so far...
Quoted 28 lines
bypass functionality is not generally used and bypass bits should not be changed by the kernel gic code as it could lead to incorrect behavior. Tested on X-Gene mustang board.
Signed-off-by Vinayak Kale <[email protected]>Acked-by Anup Patel <[email protected]>Signed-off-by Feng Kan <[email protected]>---
V4: Change to use bypass mask, change to use more suitable variable name.
V3: Fix code not touch other bits other than bypass bits.drivers/irqchip/irq-gic.c | 20 +++++++++++++++++--- 1 files changed, 17 insertions(+), 3 deletions(-)drivers/irqchip/irq-gic.c +2
-0@@ -97,6 +97,8 @@ struct irq_chip gic_arch_extn = {#define MAX_GIC_NR 1#endif +#define GIC_BYPASS_MASK 0x1e0 +static struct gic_chip_data gic_data[MAX_GIC_NR ]__read_mostly ;#ifdef CONFIG_GIC_NON_BANKED
drivers/irqchip/irq-gic.c static void gic_cpu_init(struct gic_chip_data *gic) · line 423
Quoted 4 lines
drivers/irqchip/irq-gic.c +1
-0@@ -418,6 +420,7 @@ static void gic_cpu_init(struct gic_chip_data *gic)void __iomem *dist_base =gic_data_dist_base (gic);void __iomem *base =gic_data_cpu_base (gic);unsigned int cpu_mask, cpu =smp_processor_id (); +unsigned int bypass;
Please use a type that corresponds to the width of the access (u32 in this case).
Quoted 35 lines
drivers/irqchip/irq-gic.c +10
-2int i;/* @@ -449,13 +452,20 @@ static void gic_cpu_init(struct gic_chip_data *gic)writel_relaxed (0xa0a0a0a0 , dist_base +GIC_DIST_PRI + i *4 /4 );writel_relaxed (0xf0 , base +GIC_CPU_PRIMASK ); -writel_relaxed (1 , base +GIC_CPU_CTRL ); + + bypass =readl (base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass |0x1 , base +GIC_CPU_CTRL ); }void gic_cpu_if_down (void ) {void __iomem *cpu_base =gic_data_cpu_base (&gic_data[0 ]); -writel_relaxed (0 , cpu_base +GIC_CPU_CTRL ); +unsigned int bypass; + + bypass =readl (cpu_base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass, cpu_base +GIC_CPU_CTRL ); }#ifdef CONFIG_CPU_PM @@ -566,6 +576,7 @@ static void gic_cpu_restore(unsigned int gic_nr) {int i;u32 *ptr; +unsigned int bypass;void __iomem *dist_base;void __iomem *cpu_base;
drivers/irqchip/irq-gic.c static void gic_cpu_restore(unsigned int gic_nr) · line 607
Quoted 8 lines
drivers/irqchip/irq-gic.c +4
-1@@ -590,7 +601,10 @@ static void gic_cpu_restore(unsigned int gic_nr)writel_relaxed (0xa0a0a0a0 , dist_base +GIC_DIST_PRI + i *4 );writel_relaxed (0xf0 , cpu_base +GIC_CPU_PRIMASK ); -writel_relaxed (1 , cpu_base +GIC_CPU_CTRL ); + + bypass =readl (cpu_base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass |0x1 , cpu_base +GIC_CPU_CTRL );
It would be good to turn these into a static function (gic_cpu_if_up, matching gic_cpu_if_down?), and use it in both gic_cpu_init and gic_cpu_restore.
Thanks,
M.
Signature · 1 line
Jazz is not dead. It just smells funny.
Quoted 10 lines · Marc Zyngier
Quoted 3 lines · Feng Kan
This change is made to preserve the GIC v2 bypass bits in the
GIC_CPU_CTRLregister (also known as theGICC_CTLRregister in spec). This code will preserve all bits configured by the bootload regardingbootloader
Quoted 1 line
v2 bypass group bits. In the X-Gene platform (as well others), the
Which other platform? It'd be interesting to know which one, as you're implying they haven't managed to boot a mainline kernel so far...
Okay, wording could use some refinement here. What I mean is that most platform would probably not use the bypass feature. Correct me if I am wrong here. Not setting the bypass bit does not impact booting kernel, it only create incorrect behavior when the impacted irq are used.
Quoted 73 lines
Quoted 28 lines
bypass functionality is not generally used and bypass bits should not be changed by the kernel gic code as it could lead to incorrect behavior. Tested on X-Gene mustang board.
Signed-off-by Vinayak Kale <[email protected]>Acked-by Anup Patel <[email protected]>Signed-off-by Feng Kan <[email protected]>---
V4: Change to use bypass mask, change to use more suitable variable name.
V3: Fix code not touch other bits other than bypass bits.drivers/irqchip/irq-gic.c | 20 +++++++++++++++++--- 1 files changed, 17 insertions(+), 3 deletions(-)drivers/irqchip/irq-gic.c +2
-0@@ -97,6 +97,8 @@ struct irq_chip gic_arch_extn = {#define MAX_GIC_NR 1#endif +#define GIC_BYPASS_MASK 0x1e0 +static struct gic_chip_data gic_data[MAX_GIC_NR ]__read_mostly ;#ifdef CONFIG_GIC_NON_BANKED drivers/irqchip/irq-gic.c static void gic_cpu_init(struct gic_chip_data *gic) · line 423
Quoted 4 lines
drivers/irqchip/irq-gic.c +1
-0@@ -418,6 +420,7 @@ static void gic_cpu_init(struct gic_chip_data *gic)void __iomem *dist_base =gic_data_dist_base (gic);void __iomem *base =gic_data_cpu_base (gic);unsigned int cpu_mask, cpu =smp_processor_id (); +unsigned int bypass;Please use a type that corresponds to the width of the access (u32 in this case).
Quoted 37 lines
drivers/irqchip/irq-gic.c +10
-2int i;/* @@ -449,13 +452,20 @@ static void gic_cpu_init(struct gic_chip_data *gic)writel_relaxed (0xa0a0a0a0 , dist_base +GIC_DIST_PRI + i *4 /4 );writel_relaxed (0xf0 , base +GIC_CPU_PRIMASK ); -writel_relaxed (1 , base +GIC_CPU_CTRL ); + + bypass =readl (base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass |0x1 , base +GIC_CPU_CTRL ); }void gic_cpu_if_down (void ) {void __iomem *cpu_base =gic_data_cpu_base (&gic_data[0 ]); -writel_relaxed (0 , cpu_base +GIC_CPU_CTRL ); +unsigned int bypass; + + bypass =readl (cpu_base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass, cpu_base +GIC_CPU_CTRL ); }#ifdef CONFIG_CPU_PM @@ -566,6 +576,7 @@ static void gic_cpu_restore(unsigned int gic_nr) {int i;u32 *ptr; +unsigned int bypass;void __iomem *dist_base;void __iomem *cpu_base;@@ -590,7 +601,10 @@ static void gic_cpu_restore(unsigned int gic_nr)writel_relaxed (0xa0a0a0a0 , dist_base +GIC_DIST_PRI + i *4 );
Quoted 10 lines
drivers/irqchip/irq-gic.c static void gic_cpu_restore(unsigned int gic_nr) · line 607
Quoted 6 lines
drivers/irqchip/irq-gic.c +4
-1writel_relaxed (0xf0 , cpu_base +GIC_CPU_PRIMASK ); -writel_relaxed (1 , cpu_base +GIC_CPU_CTRL ); + + bypass =readl (cpu_base +GIC_CPU_CTRL ); + bypass &=GIC_BYPASS_MASK ; +writel_relaxed (bypass |0x1 , cpu_base +GIC_CPU_CTRL );It would be good to turn these into a static function (
gic_cpu_if_up, matchinggic_cpu_if_down?), and use it in bothgic_cpu_initandgic_cpu_restore.
Would a macro be better here, please see my next patch. As two additional static functions seems a bit heavy. Please let me know. Thanks
Quoted 6 lines
Thanks,
M.--
Jazz is not dead. It just smells funny.