Skip to contentSkip to conversation

drm/i915/vlv: assert and de-assert sideband reset at boot and resume v3

PATCH In review Jesse Barnes 3 participants 10 messages May 23, 2014 – May 28, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/6 drm/i915/vlv: assert and de-assert sideband reset at boot and resume v3

This is a bit like the CMN reset de-assert we do in DPIO_CTL, except that it resets the whole common lane section of the PHY. This is required on machines where the BIOS doesn't do this for us on boot or resume to properly re-calibrate and get the PHY ready to transmit data.

Without this patch, such machines won't resume correctly much of the time, with the symptom being a 'port ready' timeout and/or a link training failure.

Note that simply asserting reset at suspend and de-asserting at resume is not sufficient, nor is simply de-asserting at boot. Both of these cases have been tested and have still been found to have failures on some configurations.

v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)

---
 drivers/gpu/drm/i915/intel_display.c | 19 +++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h     |  3 ++-
 drivers/gpu/drm/i915/intel_pm.c      | 13 ++++++++++---
 3 files changed, 31 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/intel_display.c +19 -0
index df58afc..bdb4624 100644
@@ -1509,6 +1509,25 @@ static void intel_reset_dpio(struct drm_device *dev)
 
 	} else {
 		/*
+		 * If DPIO has already been reset, e.g. by BIOS, just skip all
+		 * this.
+		 */
+		if (I915_READ(DPIO_CTL) & DPIO_CMNRST)
+			return;
+
+		/*
+		 * From VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_11.docx:
+		 * Need to assert and de-assert PHY SB reset by gating the
+		 * common lane power, then un-gating it.
+		 * Simply ungating isn't enough to reset the PHY enough to get
+		 * ports and lanes running.
+		 */
+		__vlv_set_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC,
+				     false);
+		__vlv_set_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC,
+				     true);
+
+		/*
 		 * From VLV2A0_DP_eDP_DPIO_driver_vbios_notes_10.docx -
 		 *  6.	De-assert cmn_reset/side_reset. Same as VLV X0.
 		 *   a.	GUnit 0x2110 bit[0] set to 1 (def 0)
drivers/gpu/drm/i915/intel_drv.h +2 -1
index 0ef2777..feb6165 100644
@@ -966,7 +966,8 @@ void intel_runtime_pm_put(struct drm_i915_private *dev_priv);
 void intel_init_runtime_pm(struct drm_i915_private *dev_priv);
 void intel_fini_runtime_pm(struct drm_i915_private *dev_priv);
 void ilk_wm_get_hw_state(struct drm_device *dev);
-
+void __vlv_set_power_well(struct drm_i915_private *dev_priv,
+			  enum punit_power_well power_well_id, bool enable);
 
 /* intel_sdvo.c */
 bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob);
drivers/gpu/drm/i915/intel_pm.c +10 -3
index b59e8ab..8f7dbb9 100644
@@ -5724,10 +5724,9 @@ static bool i9xx_always_on_power_well_enabled(struct drm_i915_private *dev_priv,
 	return true;
 }
 
-static void vlv_set_power_well(struct drm_i915_private *dev_priv,
-			       struct i915_power_well *power_well, bool enable)
+void __vlv_set_power_well(struct drm_i915_private *dev_priv,
+			  enum punit_power_well power_well_id, bool enable)
 {
-	enum punit_power_well power_well_id = power_well->data;
 	u32 mask;
 	u32 state;
 	u32 ctrl;
@@ -5760,6 +5759,14 @@ out:
 	mutex_unlock(&dev_priv->rps.hw_lock);
 }
 
+static void vlv_set_power_well(struct drm_i915_private *dev_priv,
+			       struct i915_power_well *power_well, bool enable)
+{
+	enum punit_power_well power_well_id = power_well->data;
+
+	__vlv_set_power_well(dev_priv, power_well_id, enable);
+}
+
 static void vlv_power_well_sync_hw(struct drm_i915_private *dev_priv,
 				   struct i915_power_well *power_well)
 {
Signature · 1 line
1.8.4.2
#1 lore raw

PATCH 2/6 drm/i915/vlv: drop power well enable in uncore_sanitize

We do this at runtime and later on now.

---
 drivers/gpu/drm/i915/intel_uncore.c | 18 ------------------
 1 file changed, 18 deletions(-)
drivers/gpu/drm/i915/intel_uncore.c +0 -18
index 27fe2df..bcd6945 100644
@@ -393,26 +393,8 @@ void intel_uncore_early_sanitize(struct drm_device *dev)
 
 void intel_uncore_sanitize(struct drm_device *dev)
 {
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	u32 reg_val;
-
 	/* BIOS often leaves RC6 enabled, but disable it for hw init */
 	intel_disable_gt_powersave(dev);
-
-	/* Turn off power gate, require especially for the BIOS less system */
-	if (IS_VALLEYVIEW(dev)) {
-
-		mutex_lock(&dev_priv->rps.hw_lock);
-		reg_val = vlv_punit_read(dev_priv, PUNIT_REG_PWRGT_STATUS);
-
-		if (reg_val & (PUNIT_PWRGT_PWR_GATE(PUNIT_POWER_WELL_RENDER) |
-			       PUNIT_PWRGT_PWR_GATE(PUNIT_POWER_WELL_MEDIA) |
-			       PUNIT_PWRGT_PWR_GATE(PUNIT_POWER_WELL_DISP2D)))
-			vlv_punit_write(dev_priv, PUNIT_REG_PWRGT_CTRL, 0x0);
-
-		mutex_unlock(&dev_priv->rps.hw_lock);
-
-	}
 }
 
 /*
Signature · 1 line
1.8.4.2
#2 lore raw

PATCH 3/6 drm/i915/vlv: move CRI refclk enable into __vlv_set_power_well

In reply to Jesse Barnes

This needs to be done before we power back on the CMN_BC well so the PHY can calibrate properly.

---
 drivers/gpu/drm/i915/intel_display.c |  8 --------
 drivers/gpu/drm/i915/intel_pm.c      | 11 +++++++++++
 2 files changed, 11 insertions(+), 8 deletions(-)
drivers/gpu/drm/i915/intel_display.c +0 -8
index bdb4624..369cd1e 100644
@@ -1477,14 +1477,6 @@ static void intel_reset_dpio(struct drm_device *dev)
 	if (!IS_VALLEYVIEW(dev))
 		return;
 
-	/*
-	 * Enable the CRI clock source so we can get at the display and the
-	 * reference clock for VGA hotplug / manual detection.
-	 */
-	I915_WRITE(DPLL(PIPE_B), I915_READ(DPLL(PIPE_B)) |
-		   DPLL_REFA_CLK_ENABLE_VLV |
-		   DPLL_INTEGRATED_CRI_CLK_VLV);
-
 	if (IS_CHERRYVIEW(dev)) {
 		enum dpio_phy phy;
 		u32 val;
drivers/gpu/drm/i915/intel_pm.c +11 -0
index 8f7dbb9..e8f0c85 100644
@@ -5731,6 +5731,17 @@ void __vlv_set_power_well(struct drm_i915_private *dev_priv,
 	u32 state;
 	u32 ctrl;
 
+	if (power_well_id == PUNIT_POWER_WELL_DPIO_CMN_BC && enable) {
+		/*
+		 * Enable the CRI clock source so we can get at the display
+		 * and the reference clock for VGA hotplug / manual detection.
+		 */
+		I915_WRITE(DPLL(PIPE_B), I915_READ(DPLL(PIPE_B)) |
+			   DPLL_REFA_CLK_ENABLE_VLV |
+			   DPLL_INTEGRATED_CRI_CLK_VLV);
+		udelay(1); /* >10ns for cmnreset, >0ns for sidereset */
+	}
+
 	mask = PUNIT_PWRGT_MASK(power_well_id);
 	state = enable ? PUNIT_PWRGT_PWR_ON(power_well_id) :
 			 PUNIT_PWRGT_PWR_GATE(power_well_id);
Signature · 1 line
1.8.4.2
#3 lore raw

PATCH 4/6 drm/i915/vlv: re-order power wells so DPIO common comes after TX

In reply to Jesse Barnes

There may be a dependency here.

---
 drivers/gpu/drm/i915/intel_pm.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +6 -6
index e8f0c85..fb7e23e 100644
@@ -6122,12 +6122,6 @@ static struct i915_power_well vlv_power_wells[] = {
 		.ops = &vlv_display_power_well_ops,
 	},
 	{
-		.name = "dpio-common",
-		.domains = VLV_DPIO_CMN_BC_POWER_DOMAINS,
-		.data = PUNIT_POWER_WELL_DPIO_CMN_BC,
-		.ops = &vlv_dpio_power_well_ops,
-	},
-	{
 		.name = "dpio-tx-b-01",
 		.domains = VLV_DPIO_TX_B_LANES_01_POWER_DOMAINS |
 			   VLV_DPIO_TX_B_LANES_23_POWER_DOMAINS |
@@ -6163,6 +6157,12 @@ static struct i915_power_well vlv_power_wells[] = {
 		.ops = &vlv_dpio_power_well_ops,
 		.data = PUNIT_POWER_WELL_DPIO_TX_C_LANES_23,
 	},
+	{
+		.name = "dpio-common",
+		.domains = VLV_DPIO_CMN_BC_POWER_DOMAINS,
+		.data = PUNIT_POWER_WELL_DPIO_CMN_BC,
+		.ops = &vlv_dpio_power_well_ops,
+	},
 };
 
 #define set_power_wells(power_domains, __power_wells) ({		\
Signature · 1 line
1.8.4.2
#4 lore raw

Re: [PATCH 4/6] drm/i915/vlv: re-order power wells so DPIO common comes after TX

Quoted 3 lines · Jesse Barnes

There may be a dependency here.

Hm, this implicit ordering is a bit funky imo ... If this increase in complexity in furture platforms I think we should switch to epxlicit depencies and grab references in turn. Turtles all the way down and all. -Daniel

Quoted 41 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +6 -6
index e8f0c85..fb7e23e 100644
@@ -6122,12 +6122,6 @@ static struct i915_power_well vlv_power_wells[] = {
 		.ops = &vlv_display_power_well_ops,
 	},
 	{
-		.name = "dpio-common",
-		.domains = VLV_DPIO_CMN_BC_POWER_DOMAINS,
-		.data = PUNIT_POWER_WELL_DPIO_CMN_BC,
-		.ops = &vlv_dpio_power_well_ops,
-	},
-	{
 		.name = "dpio-tx-b-01",
 		.domains = VLV_DPIO_TX_B_LANES_01_POWER_DOMAINS |
 			   VLV_DPIO_TX_B_LANES_23_POWER_DOMAINS |
@@ -6163,6 +6157,12 @@ static struct i915_power_well vlv_power_wells[] = {
 		.ops = &vlv_dpio_power_well_ops,
 		.data = PUNIT_POWER_WELL_DPIO_TX_C_LANES_23,
 	},
+	{
+		.name = "dpio-common",
+		.domains = VLV_DPIO_CMN_BC_POWER_DOMAINS,
+		.data = PUNIT_POWER_WELL_DPIO_CMN_BC,
+		.ops = &vlv_dpio_power_well_ops,
+	},
 };
 
 #define set_power_wells(power_domains, __power_wells) ({		\
Signature · 6 lines
1.8.4.2

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 3 lines
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
#5 lore raw

PATCH 5/6 drm/i915/vlv: move DPIO common reset de-assert into __vlv_set_power_well

In reply to Jesse Barnes

We need to do this anytime we power gate the DPIO common well.

---
 drivers/gpu/drm/i915/intel_display.c | 13 ------------
 drivers/gpu/drm/i915/intel_pm.c      | 39 +++++++++++++++++++++++++++---------
 2 files changed, 30 insertions(+), 22 deletions(-)
drivers/gpu/drm/i915/intel_display.c +0 -13
index 369cd1e..bfa1fc7 100644
@@ -1518,19 +1518,6 @@ static void intel_reset_dpio(struct drm_device *dev)
 				     false);
 		__vlv_set_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC,
 				     true);
-
-		/*
-		 * From VLV2A0_DP_eDP_DPIO_driver_vbios_notes_10.docx -
-		 *  6.	De-assert cmn_reset/side_reset. Same as VLV X0.
-		 *   a.	GUnit 0x2110 bit[0] set to 1 (def 0)
-		 *   b.	The other bits such as sfr settings / modesel may all
-		 *	be set to 0.
-		 *
-		 * This should only be done on init and resume from S3 with
-		 * both PLLs disabled, or we risk losing DPIO and PLL
-		 * synchronization.
-		 */
-		I915_WRITE(DPIO_CTL, I915_READ(DPIO_CTL) | DPIO_CMNRST);
 	}
 }
 
drivers/gpu/drm/i915/intel_pm.c +30 -9
index fb7e23e..948a4aa 100644
@@ -5731,15 +5731,22 @@ void __vlv_set_power_well(struct drm_i915_private *dev_priv,
 	u32 state;
 	u32 ctrl;
 
-	if (power_well_id == PUNIT_POWER_WELL_DPIO_CMN_BC && enable) {
-		/*
-		 * Enable the CRI clock source so we can get at the display
-		 * and the reference clock for VGA hotplug / manual detection.
-		 */
-		I915_WRITE(DPLL(PIPE_B), I915_READ(DPLL(PIPE_B)) |
-			   DPLL_REFA_CLK_ENABLE_VLV |
-			   DPLL_INTEGRATED_CRI_CLK_VLV);
-		udelay(1); /* >10ns for cmnreset, >0ns for sidereset */
+	if (power_well_id == PUNIT_POWER_WELL_DPIO_CMN_BC) {
+		if (enable) {
+			/*
+			 * Enable the CRI clock source so we can get at the
+			 * display and the reference clock for VGA
+			 * hotplug / manual detection.
+			 */
+			I915_WRITE(DPLL(PIPE_B), I915_READ(DPLL(PIPE_B)) |
+				   DPLL_REFA_CLK_ENABLE_VLV |
+				   DPLL_INTEGRATED_CRI_CLK_VLV);
+			udelay(1); /* >10ns for cmnreset, >0ns for sidereset */
+		} else {
+			/* Assert common reset */
+			I915_WRITE(DPIO_CTL, I915_READ(DPIO_CTL) &
+				   ~DPIO_CMNRST);
+		}
 	}
 
 	mask = PUNIT_PWRGT_MASK(power_well_id);
@@ -5768,6 +5775,20 @@ void __vlv_set_power_well(struct drm_i915_private *dev_priv,
 
 out:
 	mutex_unlock(&dev_priv->rps.hw_lock);
+
+	/*
+	 * From VLV2A0_DP_eDP_DPIO_driver_vbios_notes_10.docx -
+	 *  6.	De-assert cmn_reset/side_reset. Same as VLV X0.
+	 *   a.	GUnit 0x2110 bit[0] set to 1 (def 0)
+	 *   b.	The other bits such as sfr settings / modesel may all
+	 *	be set to 0.
+	 *
+	 * This should only be done on init and resume from S3 with
+	 * both PLLs disabled, or we risk losing DPIO and PLL
+	 * synchronization.
+	 */
+	if (power_well_id == PUNIT_POWER_WELL_DPIO_CMN_BC && enable)
+		I915_WRITE(DPIO_CTL, I915_READ(DPIO_CTL) | DPIO_CMNRST);
 }
 
 static void vlv_set_power_well(struct drm_i915_private *dev_priv,
Signature · 1 line
1.8.4.2
#6 lore raw

PATCH 6/6 drm/i915/vlv: add pll assertion when disabling DPIO common well

In reply to Jesse Barnes

When doing this, all PLLs should be disabled.

---
 drivers/gpu/drm/i915/intel_pm.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/gpu/drm/i915/intel_pm.c +4 -0
index 948a4aa..452518f 100644
@@ -5727,9 +5727,11 @@ static bool i9xx_always_on_power_well_enabled(struct drm_i915_private *dev_priv,
 void __vlv_set_power_well(struct drm_i915_private *dev_priv,
 			  enum punit_power_well power_well_id, bool enable)
 {
+	struct drm_device *dev = dev_priv->dev;
 	u32 mask;
 	u32 state;
 	u32 ctrl;
+	enum pipe pipe;
 
 	if (power_well_id == PUNIT_POWER_WELL_DPIO_CMN_BC) {
 		if (enable) {
@@ -5743,6 +5745,8 @@ void __vlv_set_power_well(struct drm_i915_private *dev_priv,
 				   DPLL_INTEGRATED_CRI_CLK_VLV);
 			udelay(1); /* >10ns for cmnreset, >0ns for sidereset */
 		} else {
+			for_each_pipe(pipe)
+				assert_pll_disabled(dev_priv, pipe);
 			/* Assert common reset */
 			I915_WRITE(DPIO_CTL, I915_READ(DPIO_CTL) &
 				   ~DPIO_CMNRST);
Signature · 1 line
1.8.4.2
Reviewed-by on v1 1/6
#7 lore raw
In reply to Jesse Barnes
Quoted 14 lines · Jesse Barnes

This is a bit like the CMN reset de-assert we do in DPIO_CTL, except that it resets the whole common lane section of the PHY. This is required on machines where the BIOS doesn't do this for us on boot or resume to properly re-calibrate and get the PHY ready to transmit data.

Without this patch, such machines won't resume correctly much of the time, with the symptom being a 'port ready' timeout and/or a link training failure.

Note that simply asserting reset at suspend and de-asserting at resume is not sufficient, nor is simply de-asserting at boot. Both of these cases have been tested and have still been found to have failures on some configurations.

Quoted 5 lines

v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)

The series matches my understanding of the limitations of the PHY, so:

But if these limitations are real, then I think we would also need to adjust the power domains to power up all the wells whenever even a single one is required.

This should be testable I think by simply:
1. disable both ports
2. enable one port
3. enable the other port

At step 3. the common well is already up, so the TX wells for the second port should come up in some kind of poor state.

Quoted 89 lines
---
 drivers/gpu/drm/i915/intel_display.c | 19 +++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h     |  3 ++-
 drivers/gpu/drm/i915/intel_pm.c      | 13 ++++++++++---
 3 files changed, 31 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/intel_display.c +19 -0
index df58afc..bdb4624 100644
@@ -1509,6 +1509,25 @@ static void intel_reset_dpio(struct drm_device *dev)
 
 	} else {
 		/*
+		 * If DPIO has already been reset, e.g. by BIOS, just skip all
+		 * this.
+		 */
+		if (I915_READ(DPIO_CTL) & DPIO_CMNRST)
+			return;
+
+		/*
+		 * From VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_11.docx:
+		 * Need to assert and de-assert PHY SB reset by gating the
+		 * common lane power, then un-gating it.
+		 * Simply ungating isn't enough to reset the PHY enough to get
+		 * ports and lanes running.
+		 */
+		__vlv_set_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC,
+				     false);
+		__vlv_set_power_well(dev_priv, PUNIT_POWER_WELL_DPIO_CMN_BC,
+				     true);
+
+		/*
 		 * From VLV2A0_DP_eDP_DPIO_driver_vbios_notes_10.docx -
 		 *  6.	De-assert cmn_reset/side_reset. Same as VLV X0.
 		 *   a.	GUnit 0x2110 bit[0] set to 1 (def 0)
drivers/gpu/drm/i915/intel_drv.h +2 -1
index 0ef2777..feb6165 100644
@@ -966,7 +966,8 @@ void intel_runtime_pm_put(struct drm_i915_private *dev_priv);
 void intel_init_runtime_pm(struct drm_i915_private *dev_priv);
 void intel_fini_runtime_pm(struct drm_i915_private *dev_priv);
 void ilk_wm_get_hw_state(struct drm_device *dev);
-
+void __vlv_set_power_well(struct drm_i915_private *dev_priv,
+			  enum punit_power_well power_well_id, bool enable);
 
 /* intel_sdvo.c */
 bool intel_sdvo_init(struct drm_device *dev, uint32_t sdvo_reg, bool is_sdvob);
drivers/gpu/drm/i915/intel_pm.c +10 -3
index b59e8ab..8f7dbb9 100644
@@ -5724,10 +5724,9 @@ static bool i9xx_always_on_power_well_enabled(struct drm_i915_private *dev_priv,
 	return true;
 }
 
-static void vlv_set_power_well(struct drm_i915_private *dev_priv,
-			       struct i915_power_well *power_well, bool enable)
+void __vlv_set_power_well(struct drm_i915_private *dev_priv,
+			  enum punit_power_well power_well_id, bool enable)
 {
-	enum punit_power_well power_well_id = power_well->data;
 	u32 mask;
 	u32 state;
 	u32 ctrl;
@@ -5760,6 +5759,14 @@ out:
 	mutex_unlock(&dev_priv->rps.hw_lock);
 }
 
+static void vlv_set_power_well(struct drm_i915_private *dev_priv,
+			       struct i915_power_well *power_well, bool enable)
+{
+	enum punit_power_well power_well_id = power_well->data;
+
+	__vlv_set_power_well(dev_priv, power_well_id, enable);
+}
+
 static void vlv_power_well_sync_hw(struct drm_i915_private *dev_priv,
 				   struct i915_power_well *power_well)
 {
Signature · 6 lines
1.8.4.2

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 2 lines
Ville Syrjälä
Intel OTC
#8 lore raw
Quoted 15 lines · Ville Syrjälä
Quoted 14 lines · Jesse Barnes

This is a bit like the CMN reset de-assert we do in DPIO_CTL, except that it resets the whole common lane section of the PHY. This is required on machines where the BIOS doesn't do this for us on boot or resume to properly re-calibrate and get the PHY ready to transmit data.

Without this patch, such machines won't resume correctly much of the time, with the symptom being a 'port ready' timeout and/or a link training failure.

Note that simply asserting reset at suspend and de-asserting at resume is not sufficient, nor is simply de-asserting at boot. Both of these cases have been tested and have still been found to have failures on some configurations.

Quoted 8 lines
Quoted 5 lines

v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)

The series matches my understanding of the limitations of the PHY, so:

All merged to dinq, thanks.

Quoted 11 lines

But if these limitations are real, then I think we would also need to adjust the power domains to power up all the wells whenever even a single one is required.

This should be testable I think by simply:
1. disable both ports
2. enable one port
3. enable the other port

At step 3. the common well is already up, so the TX wells for the second port should come up in some kind of poor state.

Hm, if we need this we might forc a modeset for _all_ pipes on vlv, even for unchanged ports. At elast as long as we enable something new. That should make this work properly I hope.
-Daniel

Signature · 3 lines
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
#9 lore raw
Quoted 36 lines · Daniel Vetter
Quoted 15 lines · Ville Syrjälä
Quoted 14 lines · Jesse Barnes

This is a bit like the CMN reset de-assert we do in DPIO_CTL, except that it resets the whole common lane section of the PHY. This is required on machines where the BIOS doesn't do this for us on boot or resume to properly re-calibrate and get the PHY ready to transmit data.

Without this patch, such machines won't resume correctly much of the time, with the symptom being a 'port ready' timeout and/or a link training failure.

Note that simply asserting reset at suspend and de-asserting at resume is not sufficient, nor is simply de-asserting at boot. Both of these cases have been tested and have still been found to have failures on some configurations.

Quoted 8 lines
Quoted 5 lines

v2: extract simpler set_power_well function for use in reset_dpio (Imre)
move to reset_dpio (Daniel & Ville)
v3: don't reset if DPIO reset is already de-asserted (Imre)

The series matches my understanding of the limitations of the PHY, so:

All merged to dinq, thanks.

Quoted 9 lines

But if these limitations are real, then I think we would also need to adjust the power domains to power up all the wells whenever even a single one is required.

This should be testable I think by simply:
1. disable both ports
2. enable one port
3. enable the other port

Quoted 6 lines
Quoted 2 lines

At step 3. the common well is already up, so the TX wells for the second port should come up in some kind of poor state.

Hm, if we need this we might forc a modeset for _all_ pipes on vlv, even for unchanged ports. At elast as long as we enable something new. That should make this work properly I hope.

Yeah that would work too, but obviously would cause some blinking that might be a bit disturbing. But we may have such blinking already due to adjusting cdclk. If the blinking is disturbing for users we might want to have a knob for controlling it: either use less power but blink more, or waste a bit of power and blink less. But I don't know if anyone would really want to waste power.

Signature · 2 lines
Ville Syrjälä
Intel OTC