Staging: rtl8192u: r8180_93cx6.c Added missing spaces
PATCH 1/1 Staging: rtl8192u: r8180_93cx6.c Added missing spaces
Added spaces needed in the proper places to address:
ERROR: space required after that ',' (ctx:VxV)
ERROR: space required after that ';' (ctx:VxV)
ERROR: space required after that close brace '}'
ERROR: space required before the open brace '{'
ERROR: space required before the open parenthesis '('
ERROR: spaces required around that '<' (ctx:VxV)
ERROR: spaces required around that '=' (ctx:VxV)
ERROR: spaces required around that '==' (ctx:VxV)
Signed-off-by Chaitanya Hazarey <[email protected]>
--- drivers/staging/rtl8192u/r8180_93cx6.c | 46 +++++++++++++++++----------------- 1 file changed, 23 insertions(+), 23 deletions(-)
drivers/staging/rtl8192u/r8180_93cx6.c +23 -23
@@ -53,7 +53,7 @@ static void eprom_ck_cycle(struct net_device *dev) } -static void eprom_w (struct net_device *dev,short bit) +static void eprom_w (struct net_device *dev,short bit) {u8 cmdreg;
@@ -86,7 +86,7 @@ static void eprom_send_bits_string(struct net_device *dev, short b[], int len) {int i; -for (i=0 ; i<len; i++){ +for (i =0 ; i < len; i++) {eprom_w (dev, b[i]);eprom_ck_cycle (dev); }
@@ -96,37 +96,37 @@ static void eprom_send_bits_string(struct net_device *dev, short b[], int len)u32 eprom_read (struct net_device *dev,u32 addr) {struct r8192_priv *priv =ieee80211_priv (dev); -short read_cmd[]={1 ,1 ,0 }; +short read_cmd[] = {1 ,1 ,0 };short addr_str[8 ];int i;int addr_len;u32 ret; - ret=0 ; + ret =0 ;//enable EPROM programming write_nic_byte_E (dev,EPROM_CMD , (EPROM_CMD_PROGRAM <<EPROM_CMD_OPERATING_MODE_SHIFT ));force_pci_posting (dev);udelay (EPROM_DELAY ); -if (priv->epromtype==EPROM_93c56){ - addr_str[7 ]=addr &1 ; - addr_str[6 ]=addr & (1 <<1 ); - addr_str[5 ]=addr & (1 <<2 ); - addr_str[4 ]=addr & (1 <<3 ); - addr_str[3 ]=addr & (1 <<4 ); - addr_str[2 ]=addr & (1 <<5 ); - addr_str[1 ]=addr & (1 <<6 ); - addr_str[0 ]=addr & (1 <<7 ); - addr_len=8 ; - }else { - addr_str[5 ]=addr &1 ; - addr_str[4 ]=addr & (1 <<1 ); - addr_str[3 ]=addr & (1 <<2 ); - addr_str[2 ]=addr & (1 <<3 ); - addr_str[1 ]=addr & (1 <<4 ); - addr_str[0 ]=addr & (1 <<5 ); - addr_len=6 ; +if (priv->epromtype == EPROM_93c56) { + addr_str[7 ] = addr &1 ; + addr_str[6 ] = addr & (1 <<1 ); + addr_str[5 ] = addr & (1 <<2 ); + addr_str[4 ] = addr & (1 <<3 ); + addr_str[3 ] = addr & (1 <<4 ); + addr_str[2 ] = addr & (1 <<5 ); + addr_str[1 ] = addr & (1 <<6 ); + addr_str[0 ] = addr & (1 <<7 ); + addr_len =8 ; + }else { + addr_str[5 ] = addr &1 ; + addr_str[4 ] = addr & (1 <<1 ); + addr_str[3 ] = addr & (1 <<2 ); + addr_str[2 ] = addr & (1 <<3 ); + addr_str[1 ] = addr & (1 <<4 ); + addr_str[0 ] = addr & (1 <<5 ); + addr_len =6 ; }eprom_cs (dev,1 );eprom_ck_cycle (dev);
@@ -137,7 +137,7 @@ u32 eprom_read(struct net_device *dev, u32 addr)//I'm unsure if it is necessary, but anyway shouldn't hurt eprom_w (dev,0 ); -for (i=0 ;i<16 ;i++){ +for (i =0 ; i <16 ; i++) {//eeprom needs a clk cycle between writing opcode&adr //and reading data. (eeprom outs a dummy 0) eprom_ck_cycle (dev);
Signature · 1 line
1.9.1
Great. Thanks.
regards,
dan carpenter