ncr53c8xx: remove remnants of immediate arbitration

index 1d508dcbf859..49c7b723225b 100644
@@ -52,12 +52,10 @@ Written by Gerard Roudier <[email protected]>
              10.2.19 Check SCSI BUS 
              10.2.20 Exclude a host from being attached
              10.2.21 Suggest a default SCSI id for hosts
-             10.2.22 Enable use of IMMEDIATE ARBITRATION
       10.3 Advised boot setup commands
       10.4 PCI configuration fix-up boot option
       10.5 Serial NVRAM support boot option
       10.6 SCSI BUS checking boot option
-      10.7 IMMEDIATE ARBITRATION boot option
 11. Some constants and flags of the ncr53c8xx.h header file
 12. Installation
 13. Architecture dependent features

@@ -843,16 +841,6 @@ port address 0x1400.
     try to deduce the value previously set in the hardware and use value 
     7 if the hardware value is zero.
 
-10.2.22 Enable use of IMMEDIATE ARBITRATION
-        (only supported by the sym53c8xx driver. See 10.7 for more details)
-        iarb:0    do not use this feature.
-        iarb:#x   use this feature according to bit fields as follow:
-
-    bit 0 (1) : enable IARB each time the initiator has been reselected 
-                when it arbitrated for the SCSI BUS.
-    (#x >> 4) : maximum number of successive settings of IARB if the initiator 
-                win arbitration and it has other commands to send to a device.
-
 Boot fail safe
     safe:y	load the following assumed fail safe initial setup
 

@@ -876,7 +864,6 @@ Boot fail safe
   differential support		from BIOS settings	diff:1
   irq mode			from BIOS settings	irqm:1
   SCSI BUS check		do not attach on error	buschk:1
-  immediate arbitration		disabled		iarb:0
 
 10.3 Advised boot setup commands
 

@@ -1005,45 +992,6 @@ Unfortunately, the following common SCSI BUS problems are not detected:
 On the other hand, either bad cabling, broken devices, not conformant 
 devices, ... may cause a SCSI signal to be wrong when te driver reads it.
 
-10.7 IMMEDIATE ARBITRATION boot option
-
-This option is only supported by the SYM53C8XX driver (not by the NCR53C8XX).
-
-SYMBIOS 53C8XX chips are able to arbitrate for the SCSI BUS as soon as they 
-have detected an expected disconnection (BUS FREE PHASE). For this process 
-to be started, bit 1 of SCNTL1 IO register must be set when the chip is 
-connected to the SCSI BUS.
-
-When this feature has been enabled for the current connection, the chip has 
-every chance to win arbitration if only devices with lower priority are 
-competing for the SCSI BUS. By the way, when the chip is using SCSI id 7, 
-then it will for sure win the next SCSI BUS arbitration.
-
-Since, there is no way to know what devices are trying to arbitrate for the 
-BUS, using this feature can be extremely unfair. So, you are not advised
-to enable it, or at most enable this feature for the case the chip lost 
-the previous arbitration (boot option 'iarb:1').
-
-This feature has the following advantages:
-
-a) Allow the initiator with ID 7 to win arbitration when it wants so.
-b) Overlap at least 4 micro-seconds of arbitration time with the execution 
-   of SCRIPTS that deal with the end of the current connection and that 
-   starts the next job.
-
-Hmmm... But (a) may just prevent other devices from reselecting the initiator, 
-and delay data transfers or status/completions, and (b) may just waste 
-SCSI BUS bandwidth if the SCRIPTS execution lasts more than 4 micro-seconds.
-
-The use of IARB needs the SCSI_NCR_IARB_SUPPORT option to have been defined 
-at compile time and the 'iarb' boot option to have been set to a non zero 
-value at boot time. It is not that useful for real work, but can be used 
-to stress SCSI devices or for some applications that can gain advantage of 
-it. By the way, if you experience badnesses like 'unexpected disconnections', 
-'bad reselections', etc... when using IARB on heavy IO load, you should not 
-be surprised, because force-feeding anything and blocking its arse at the 
-same time cannot work for a long time. :-))
-
 
 11. Some constants and flags of the ncr53c8xx.h header file