Skip to contentSkip to conversation

BSM: How to determine size of DRAM used for internal graphics?

Intel 945 Paul Menzel 1 participant 3 messages May 30, 2014 – Jun 9, 2014

lore
Share & tools
lore
#0 lore raw

Dear Intel graphics folks,

since commit 17fec8a0 [1]

drm/i915: Use Graphics Base of Stolen Memory on all gen3+

Linux reads the register BSM (Base of Stolen Memory) directly to get the base address of graphics stolen memory. With coreboot [2] and native graphics init – note that everything works with the proprietary VGA BIOS/Option ROM – this causes a regression [3] as this register is not programmed at all.

From the datasheet *Mobile Intel® 945 Express Chipset Family* [4] the register BSM is described on page 290.

Graphics Stolen Memory and TSEG are within DRAM space defined under TOLUD. From the top of low used DRAM, (G)MCH claims 1 to 64 MBs of DRAM for internal graphics if enabled.

This register contains bits 31 to 20 of the base address of stolen
DRAM memory. The host interface determines the base of graphics stolen memory by subtracting the graphics stolen memory size from TOLUD. See Device 0 TOLUD for more explanations.

Also see Figure 12 *Main Memory Address Range* in section 9.2 on page 325.

Unfortunately I am unable to find out how the graphics stolen memory size is determined. I’d have thought it is used for the framebuffer, but according to page 93 (Graphics Mode select (GMS)) that the framebuffer size can only be 1 MB or 8 MB, which contradicts that it can be up to 64 MB.

If it is determined implicitly by the value I set the BSM to, where can I find the recommendations what size to use? I’d guess it is dependent on the RAM size, that means dependent if the system has 512 MB or 4 GB for example.

Thanks,

Paul

[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=17fec8a08698bcab98788e1e89f5b8e7502ababd
[2] http://www.coreboot.org/
[3] https://bugs.freedesktop.org/show_bug.cgi?id=79038
[4] http://www.intel.com/content/dam/www/public/us/en/documents/datasheets/mobile-945-express-chipset-datasheet.pdf

    Document Number: 309219-006

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#1 lore raw

Dear Intel graphics folks,

Am Freitag, den 30.05.2014, 13:45 +0200 schrieb Paul Menzel:

Quoted 33 lines

since commit 17fec8a0 [1]

drm/i915: Use Graphics Base of Stolen Memory on all gen3+

Linux reads the register BSM (Base of Stolen Memory) directly to get the base address of graphics stolen memory. With coreboot [2] and native graphics init – note that everything works with the proprietary VGA BIOS/Option ROM – this causes a regression [3] as this register is not programmed at all.

From the datasheet *Mobile Intel® 945 Express Chipset Family* [4] the register BSM is described on page 290.

Graphics Stolen Memory and TSEG are within DRAM space defined under TOLUD. From the top of low used DRAM, (G)MCH claims 1 to 64 MBs of DRAM for internal graphics if enabled.

This register contains bits 31 to 20 of the base address of stolen
DRAM memory. The host interface determines the base of graphics stolen memory by subtracting the graphics stolen memory size from TOLUD. See Device 0 TOLUD for more explanations.

Also see Figure 12 *Main Memory Address Range* in section 9.2 on page 325.

Unfortunately I am unable to find out how the graphics stolen memory size is determined. I’d have thought it is used for the framebuffer, but according to page 93 (Graphics Mode select (GMS)) that the framebuffer size can only be 1 MB or 8 MB, which contradicts that it can be up to 64 MB.

Quoted 4 lines

If it is determined implicitly by the value I set the BSM to, where can I find the recommendations what size to use? I’d guess it is dependent on the RAM size, that means dependent if the system has 512 MB or 4 GB for example.

The datasheet documents the bits of the register BSM as Read Only (RO). So I am even more confused now.

Thanks,

Paul

Quoted 5 lines

[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=17fec8a08698bcab98788e1e89f5b8e7502ababd
[2] http://www.coreboot.org/
[3] https://bugs.freedesktop.org/show_bug.cgi?id=79038
[4] http://www.intel.com/content/dam/www/public/us/en/documents/datasheets/mobile-945-express-chipset-datasheet.pdf

    Document Number: 309219-006

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#2 lore raw

Dear Intel graphics folks,

Am Freitag, den 30.05.2014, 14:47 +0200 schrieb Paul Menzel:

Quoted 35 lines

Am Freitag, den 30.05.2014, 13:45 +0200 schrieb Paul Menzel:

Quoted 33 lines

since commit 17fec8a0 [1]

drm/i915: Use Graphics Base of Stolen Memory on all gen3+

Linux reads the register BSM (Base of Stolen Memory) directly to get the base address of graphics stolen memory. With coreboot [2] and native graphics init – note that everything works with the proprietary VGA BIOS/Option ROM – this causes a regression [3] as this register is not programmed at all.

From the datasheet *Mobile Intel® 945 Express Chipset Family* [4] the register BSM is described on page 290.

Graphics Stolen Memory and TSEG are within DRAM space defined under TOLUD. From the top of low used DRAM, (G)MCH claims 1 to 64 MBs of DRAM for internal graphics if enabled.

This register contains bits 31 to 20 of the base address of stolen
DRAM memory. The host interface determines the base of graphics stolen memory by subtracting the graphics stolen memory size from TOLUD. See Device 0 TOLUD for more explanations.

Also see Figure 12 *Main Memory Address Range* in section 9.2 on page 325.

Unfortunately I am unable to find out how the graphics stolen memory size is determined. I’d have thought it is used for the framebuffer, but according to page 93 (Graphics Mode select (GMS)) that the framebuffer size can only be 1 MB or 8 MB, which contradicts that it can be up to 64 MB.

Quoted 7 lines
Quoted 4 lines

If it is determined implicitly by the value I set the BSM to, where can I find the recommendations what size to use? I’d guess it is dependent on the RAM size, that means dependent if the system has 512 MB or 4 GB for example.

The datasheet documents the bits of the register BSM as Read Only (RO). So I am even more confused now.

It turned out that the register is indeed read-only and that the register to look at seems to be PGTBL_CTL/PGETBL_CTL.

Thanks,

Paul

Quoted 5 lines
Quoted 5 lines

[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=17fec8a08698bcab98788e1e89f5b8e7502ababd
[2] http://www.coreboot.org/
[3] https://bugs.freedesktop.org/show_bug.cgi?id=79038
[4] http://www.intel.com/content/dam/www/public/us/en/documents/datasheets/mobile-945-express-chipset-datasheet.pdf

    Document Number: 309219-006

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx