NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
Subsystems (2)
PATCH 1/1 NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
This patch contains several fixes for Scsi START_STOP_UNIT. The previous code did not account for signed vs. unsigned arithmetic which resulted in an invalid lowest power state caculation when the device only supports 1 power state.
The code for Power Condition == 2 (Idle) was not following the spec. The spec calls out setting the device to specific power states, depending upon Power Condition Modifier, without accounting for the number of power states supported by the device.
The code for Power Condition == 3 (Standby) was using a hard-coded '0' which I replaced with the macro POWER_STATE_0.
--- drivers/block/nvme-scsi.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/block/nvme-scsi.c +6 -6
@@ -1477,7 +1477,7 @@ static int nvme_trans_power_state(struct nvme_ns *ns, struct sg_io_hdr *hdr, goto out_dma; } id_ctrl = mem; - lowest_pow_st = id_ctrl->npss -1 ; + lowest_pow_st =max (POWER_STATE_0 , (int )(id_ctrl->npss -1 ));switch (pc) {case NVME_POWER_STATE_START_VALID :
@@ -1496,18 +1496,18 @@ static int nvme_trans_power_state(struct nvme_ns *ns, struct sg_io_hdr *hdr,/* Action unspecified if POWER CONDITION MODIFIER != [0,1,2] */ /* min of desired state and (lps-1) because lps is STOP */ if (pcmod ==0x0 ) - ps_desired =min (POWER_STATE_1 , (lowest_pow_st -1 )); + ps_desired =POWER_STATE_1 ;else if (pcmod ==0x1 ) - ps_desired =min (POWER_STATE_2 , (lowest_pow_st -1 )); + ps_desired =POWER_STATE_2 ;else if (pcmod ==0x2 ) - ps_desired =min (POWER_STATE_3 , (lowest_pow_st -1 )); + ps_desired =POWER_STATE_3 ;break ;case NVME_POWER_STATE_STANDBY :/* Action unspecified if POWER CONDITION MODIFIER != [0,1] */ if (pcmod ==0x0 ) - ps_desired =max (0 , (lowest_pow_st -2 )); + ps_desired =max (POWER_STATE_0 , (lowest_pow_st -2 ));else if (pcmod ==0x1 ) - ps_desired =max (0 , (lowest_pow_st -1 )); + ps_desired =max (POWER_STATE_0 , (lowest_pow_st -1 ));break ;case NVME_POWER_STATE_LU_CONTROL :default :
Signature · 1 line
1.7.10.4
PATCH 1/1 NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
Quoted 8 lines · Dan McLeran
This patch contains several fixes for Scsi
START_STOP_UNIT. The previous code did not account for signed vs. unsigned arithmetic which resulted in an invalid lowest power state caculation when the device only supports 1 power state.The code for Power Condition == 2 (Idle) was not following the spec. The spec calls out setting the device to specific power states, depending upon Power Condition Modifier, without accounting for the number of power states supported by the device.
Quoted 8 lines
The code for Power Condition == 3 (Standby) was using a hard-coded '0' which I replaced with the macro
POWER_STATE_0.Signed-off-by Dan McLeran <daniel.mcleran at intel.com>--- drivers/block/nvme-scsi.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
Looks good.
Reviewed-by: Vishal Verma <vishal.l.verma at linux.intel.com>
Quoted 37 lines
drivers/block/nvme-scsi.c +6
-6@@ -1477,7 +1477,7 @@ static int nvme_trans_power_state(struct nvme_ns *ns, struct sg_io_hdr *hdr, goto out_dma; } id_ctrl = mem; - lowest_pow_st = id_ctrl->npss -1 ; + lowest_pow_st =max (POWER_STATE_0 , (int )(id_ctrl->npss -1 ));switch (pc) {case NVME_POWER_STATE_START_VALID :@@ -1496,18 +1496,18 @@ static int nvme_trans_power_state(struct nvme_ns *ns, struct sg_io_hdr *hdr,/* Action unspecified if POWER CONDITION MODIFIER != [0,1,2] */ /* min of desired state and (lps-1) because lps is STOP */ if (pcmod ==0x0 ) - ps_desired =min (POWER_STATE_1 , (lowest_pow_st -1 )); + ps_desired =POWER_STATE_1 ;else if (pcmod ==0x1 ) - ps_desired =min (POWER_STATE_2 , (lowest_pow_st -1 )); + ps_desired =POWER_STATE_2 ;else if (pcmod ==0x2 ) - ps_desired =min (POWER_STATE_3 , (lowest_pow_st -1 )); + ps_desired =POWER_STATE_3 ;break ;case NVME_POWER_STATE_STANDBY :/* Action unspecified if POWER CONDITION MODIFIER != [0,1] */ if (pcmod ==0x0 ) - ps_desired =max (0 , (lowest_pow_st -2 )); + ps_desired =max (POWER_STATE_0 , (lowest_pow_st -2 ));else if (pcmod ==0x1 ) - ps_desired =max (0 , (lowest_pow_st -1 )); + ps_desired =max (POWER_STATE_0 , (lowest_pow_st -1 ));break ;case NVME_POWER_STATE_LU_CONTROL :default :