ALSA: hda - verify pin:converter connection on unsol event for HSW and VLV
PATCH 1/1 ALSA: hda - verify pin:converter connection on unsol event for HSW and VLV
From: Mengdong Lin <[email protected]>
This patch will verify the pin's coverter selection for an active stream when an unsol event reports this pin becomes available again after a display mode change or hot-plug event.
For Haswell+ and Valleyview: display mode change or hot-plug can change the transcoder:port connection and make all the involved audio pins share the 1st converter. So the stream using 1st convertor will flow to multiple pins but active streams using other converters will fail. This workaround is to assure the pin selects the right conveter and an assigned converter is not shared by other unused pins.
sound/pci/hda/patch_hdmi.c +9 -1
@@ -1594,10 +1594,18 @@ static bool hdmi_present_sense(struct hdmi_spec_per_pin *per_pin, int repoll)* Re-setup pin and infoframe. This is needed e.g. when * - sink is first plugged-in (infoframe is not set up if !monitor_present) * - transcoder can change during stream playback on Haswell +* and this can make HW reset converter selection on a pin. */ -if (eld->eld_valid && !old_eld_valid && per_pin->setup) +if (eld->eld_valid && !old_eld_valid && per_pin->setup) { +if (is_haswell_plus (codec) ||is_valleyview (codec)) { +intel_verify_pin_cvt_connect (codec, per_pin); +intel_not_share_assigned_cvt (codec, pin_nid, + per_pin->mux_idx); + } +hdmi_setup_audio_infoframe (codec, per_pin, per_pin->non_pcm); + } }if (eld_changed)
Signature · 1 line
1.8.1.2
Takashi Iwai
AppliedAt Thu, 12 Jun 2014 14:42:25 +0800,
Quoted 7 lines · [email protected] wrote:
From: Mengdong Lin <[email protected]>
This patch will verify the pin's coverter selection for an active stream when an unsol event reports this pin becomes available again after a display mode change or hot-plug event.
Quoted 8 lines
For Haswell+ and Valleyview: display mode change or hot-plug can change the transcoder:port connection and make all the involved audio pins share the 1st converter. So the stream using 1st convertor will flow to multiple pins but active streams using other converters will fail. This workaround is to assure the pin selects the right conveter and an assigned converter is not shared by other unused pins.
Signed-off-by Mengdong Lin <[email protected]>
Thanks, applied now with Cc to stable.
Takashi
Quoted 28 lines
sound/pci/hda/patch_hdmi.c +9
-1@@ -1594,10 +1594,18 @@ static bool hdmi_present_sense(struct hdmi_spec_per_pin *per_pin, int repoll)* Re-setup pin and infoframe. This is needed e.g. when * - sink is first plugged-in (infoframe is not set up if !monitor_present) * - transcoder can change during stream playback on Haswell +* and this can make HW reset converter selection on a pin. */ -if (eld->eld_valid && !old_eld_valid && per_pin->setup) +if (eld->eld_valid && !old_eld_valid && per_pin->setup) { +if (is_haswell_plus (codec) ||is_valleyview (codec)) { +intel_verify_pin_cvt_connect (codec, per_pin); +intel_not_share_assigned_cvt (codec, pin_nid, + per_pin->mux_idx); + } +hdmi_setup_audio_infoframe (codec, per_pin, per_pin->non_pcm); + } }if (eld_changed)Signature · 1 line
1.8.1.2