Skip to contentSkip to conversation

Request for help booting Gumstix from MTD Flash

DISCUSSION Larry Martin 2 participants 3 messages Jun 28, 2014 – Jul 1, 2014 Memory technology devices (MTD)

lore
Share & tools
lore
#0 lore raw

Hello, I am writing this list because my question is not being answered on the Gumstix list, so I am turning to the subsystem developers. I have a u-boot, kernel and rootfs all booting properly from MMC, but when I try to boot the set from NAND the kernel says the rootfs superblock is empty.

I think the problem may be mapping of the MTD block boundaries. Gumstix provides Angstrom images in NAND, which boot fine, but their MTD partition sizes differ from mine. I started my project in Linaro and intended to distribute on MMC at first, until we had vibration issues. Now I need my Linaro stuff to work in NAND. The Linaro MTD partitions differ from the Angstrom ones. I'm hoping someone here can point me to the right information to get my system working.

My UBI volume is in MTD4. It was made from my working MMC rootfs on a Linux Mint PC using these commands:

Quoted 2 lines

sudo mkfs.ubifs -v -r /media/rootfs1 -o rootfs.ubifs -m 2048 -e 129024 -c 1996 sudo ubinize -v -o rootfs.ubi -m 2048 -p 128KiB -s 512 ubi.cfg

where ubi.cfg is:

Quoted 7 lines

[ubifs]
mode=ubi
image=rootfs.ubifs
vol_id=0
vol_type=dynamic
vol_name=rootfs
vol_flags=autoresize

rootfs.ubi starts with "UBI#". After installation with 'ubiformat -y /dev/mtd4 -f rootfs.ubi', I read MTD4 back and compared it with the input file. They differ by about 32K scattered bytes, which I assume are erase counters. MTD4 does start with "UBI#". While booted from MMC, I got these MTD sizes from /sys/class/mtd. In the Angstrom boot, MTD3 is smaller, so the start of MTD4 is different.

Quoted 6 lines
P       size             start
0 524288         80000   00000000
1 1835008       1C0000   00080000
2 262144         40000   00240000
3 8388608       800000   00280000
4 525860864   1F580000   00A80000

When I try to boot from NAND, the kernel says the superblock is empty. It should not be empty. I'm hoping somebody here can help me connect the dots. Here are the important parts of my boot log:

Quoted 25 lines
[    1.447052] UBI: attaching mtd4 to ubi0
[    1.451354] UBI: physical eraseblock size:   131072 bytes (128 KiB)
[    1.457977] UBI: logical eraseblock size:    129024 bytes
[    1.463653] UBI: smallest flash I/O unit:    2048
[    1.468597] UBI: sub-page size:              512
[    1.473480] UBI: VID header offset:          512 (aligned 512)
[    1.479614] UBI: data offset:                2048
[    2.823974] UBI: max. sequence number:       0
[    2.854461] UBI: volume 0 ("rootfs") re-sized from 2980 to 3968 LEBs
[    2.862243] UBI: attached mtd4 to ubi0
[    2.866271] UBI: MTD device name:            "rootfs"
[    2.871612] UBI: MTD device size:            501 MiB
[    2.876831] UBI: number of good PEBs:        4012
[    2.881774] UBI: number of bad PEBs:         0
[    2.886444] UBI: number of corrupted PEBs:   0
[    2.891143] UBI: max. allowed volumes:       128
[    2.896026] UBI: wear-leveling threshold:    4096
[    2.900939] UBI: number of internal volumes: 1
[    2.905639] UBI: number of user volumes:     1
[    2.910339] UBI: available PEBs:             0
[    2.915008] UBI: total number of reserved PEBs: 4012
[    2.920227] UBI: number of PEBs reserved for bad PEB handling: 40
[    2.926666] UBI: max/mean erase counter: 0/0
[    2.931152] UBI: image sequence number:  95215050
[    2.936126] UBI: background thread "ubi_bgt0d" started, PID 46

...

Quoted 46 lines
[    5.073486] UBIFS error (pid 1): ubifs_read_node: bad node type (0
but expected 6)
[    5.081542] UBIFS error (pid 1): ubifs_read_node: bad node at LEB
0:0, LEB mapping status 1
[    5.090545] Not a node, first 24 bytes:
[    5.094512] 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 ........................
[    5.108398] [<c00132b4>] (unwind_backtrace+0x0/0x11c) from
[<c01c038c>] (ubifs_read_node+0x264/0x29c)
[    5.118194] [<c01c038c>] (ubifs_read_node+0x264/0x29c) from
[<c01bd1b0>] (ubifs_read_sb_node+0x50/0x70)
[    5.128173] [<c01bd1b0>] (ubifs_read_sb_node+0x50/0x70) from
[<c01bd230>] (ubifs_read_superblock+0x20/0xeec)
[    5.138610] [<c01bd230>] (ubifs_read_superblock+0x20/0xeec) from
[<c01bbdbc>] (ubifs_mount+0x940/0x1b04)
[    5.148773] [<c01bbdbc>] (ubifs_mount+0x940/0x1b04) from [<c00e1dc8>]
(mount_fs+0x70/0x164)
[    5.157684] [<c00e1dc8>] (mount_fs+0x70/0x164) from [<c00f8400>]
(vfs_kern_mount+0x4c/0xc0)
[    5.166595] usb 1-2.1: New USB device found, idVendor=0424,
idProduct=ec00
[    5.173919] [<c00f8400>] (vfs_kern_mount+0x4c/0xc0) from [<c00f84a8>]
(do_kern_mount+0x34/0xd4)
[    5.183105] usb 1-2.1: New USB device strings: Mfr=0, Product=0,
SerialNumber=0
[    5.190856] [<c00f84a8>] (do_kern_mount+0x34/0xd4) from [<c00fa04c>]
(do_mount+0x658/0x6e8)
[    5.200347] [<c00fa04c>] (do_mount+0x658/0x6e8) from [<c00fa168>]
(sys_mount+0x84/0xc4)
[    5.209930] [<c00fa168>] (sys_mount+0x84/0xc4) from [<c0654c14>]
(mount_block_root+0xe4/0x218)
[    5.219238] [<c0654c14>] (mount_block_root+0xe4/0x218) from
[<c0654fc4>] (prepare_namespace+0x88/0x1bc)
[    5.229248] [<c0654fc4>] (prepare_namespace+0x88/0x1bc) from
[<c065496c>] (kernel_init+0x1b8/0x1f8)
[    5.238861] [<c065496c>] (kernel_init+0x1b8/0x1f8) from [<c000ee48>]
(kernel_thread_exit+0x0/0x8)
[    5.254455] List of all partitions:
[    5.258178] 1f00             512 mtdblock0  (driver?)
[    5.263580] 1f01            1792 mtdblock1  (driver?)
[    5.268920] 1f02             256 mtdblock2  (driver?)
[    5.274261] 1f03            8192 mtdblock3  (driver?)
[    5.279602] 1f04          513536 mtdblock4  (driver?)
[    5.284942] 1f05          499968 mtdblock5  (driver?)
[    5.290283] No filesystem could mount root, tried:  ubifs
[    5.295989] Kernel panic - not syncing: VFS: Unable to mount root fs
Quoted 1 line

on unknown-block(0,0)

AT 5.094 seconds, the system reads 24 bytes all zero. But my superblock starts with "UBI#" ! The sizes at 5.258 seconds look right, assuming they are 1K blocks.

See also:
http://gumstix.8.x6.nabble.com/Re-Is-there-an-easy-way-to-make-a-UBI-image-from-a-working-MMC-tt4969276.html
http://gumstix.8.x6.nabble.com/Is-there-an-easy-way-to-make-a-UBI-image-from-a-working-MMC-tt4969113.html

Thanks,
Larry

Signature · 5 lines
Larry Martin
www.GlueLogix.com
Design, Test and Support of Computerized Systems
desk USA 919.342.0201
cell USA 919.641.1733
#1 lore raw
Quoted 6 lines · Larry Martin

Hello, I am writing this list because my question is not being answered on the Gumstix list, so I am turning to the subsystem developers. I have a u-boot, kernel and rootfs all booting properly from MMC, but when I try to boot the set from NAND the kernel says the rootfs superblock is empty.

I think I just answered my own question. The last image I made worked ok. The difference was that I changed the -c 1996 to -c 4010 in the mkfs.ubifs call. My flash segment has 4011 blocks. 1996 was too few. I think the image was getting truncated. I can't explain why the superblock was coming up empty, but the image is working now.

Thanks,
Larry

#2 lore raw
In reply to Larry Martin
Quoted 5 lines · Larry Martin

Hello, I am writing this list because my question is not being answered on the Gumstix list, so I am turning to the subsystem developers. I have a u-boot, kernel and rootfs all booting properly from MMC, but when I try to boot the set from NAND the kernel says the rootfs superblock is empty.

I'd try to mark every eraseblock with its number. Then try to boot, and see what is the number of the block where UBIFS searches for the superblock.

Probably if you take your 'rootfs.ubifs', then modify it like this:

for each 128KiB-2KiB block
fill the block with its number

Then you ubinize it and to the same as you did.

And in the mount failure you should see the block number instead of zeros, I'd assume.

Or you may hack ubinize and make it put the block number to the 'sqnum' field. And then hack the UBI driver and make it print sqnum for you.

Basically this is an idea how to detect misplaced partitioning.

Signature · 2 lines
Best Regards,
Artem Bityutskiy