Skip to contentSkip to conversation

iio: Add Dyna-Image AL3320A ambient light sensor driver

PATCH Superseded Daniel Baluta 2 participants 3 messages Aug 21, 2014 – Aug 22, 2014 IIO

v2 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 iio: Add Dyna-Image AL3320A ambient light sensor driver

Minimal implementation. This driver provides raw illuminance readings.

This is based on drivers/hwmon/al3320.c (*) driver from msm tree written by Tsechih Lin <[email protected]>

* https://android.googlesource.com/kernel/msm.git

---
Changes since v1: (reported by Peter Meerwald)
* used u8 instead of int for passing gain and mean_time
* used i2c_smbus_read_word_swapped instead of 2 x i2c_smbus_read_byte_data
* used devm_iio_device_register instead of iio_device_register
* small style fixes

 drivers/iio/light/Kconfig   |  10 ++
 drivers/iio/light/Makefile  |   1 +
 drivers/iio/light/al3320a.c | 247 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 258 insertions(+)
 create mode 100644 drivers/iio/light/al3320a.c
drivers/iio/light/Kconfig +10 -0
index bf05ca5..5bea821 100644
@@ -17,6 +17,16 @@ config ADJD_S311
 	 This driver can also be built as a module.  If so, the module
 	 will be called adjd_s311.
 
+config AL3320A
+	tristate "AL3320A ambient light sensor"
+	depends on I2C
+	help
+	 Say Y here if you want to build a driver for the Dyna Image AL3320A
+	 ambient light sensor.
+
+	 To compile this driver as a module, choose M here: the
+	 module will be called al3320a.
+
 config APDS9300
 	tristate "APDS9300 ambient light sensor"
 	depends on I2C
drivers/iio/light/Makefile +1 -0
index 8b8c09f..47877a3 100644
@@ -4,6 +4,7 @@
 
 # When adding new entries keep the list in alphabetical order
 obj-$(CONFIG_ADJD_S311)		+= adjd_s311.o
+obj-$(CONFIG_AL3320A)		+= al3320a.o
 obj-$(CONFIG_APDS9300)		+= apds9300.o
 obj-$(CONFIG_CM32181)		+= cm32181.o
 obj-$(CONFIG_CM36651)		+= cm36651.o
drivers/iio/light/al3320a.c new file +247 -0

247 lines not on this page · raw message

Signature · 1 line
1.9.1
#1 lore raw
Quoted 7 lines

Minimal implementation. This driver provides raw illuminance readings.

This is based on drivers/hwmon/al3320.c (*) driver from msm tree written by Tsechih Lin <[email protected]>

* https://android.googlesource.com/kernel/msm.git

some more comments on minor things below...

Quoted 62 lines

---
Changes since v1: (reported by Peter Meerwald)
* used u8 instead of int for passing gain and mean_time
* used i2c_smbus_read_word_swapped instead of 2 x i2c_smbus_read_byte_data
* used devm_iio_device_register instead of iio_device_register
* small style fixes

 drivers/iio/light/Kconfig   |  10 ++
 drivers/iio/light/Makefile  |   1 +
 drivers/iio/light/al3320a.c | 247 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 258 insertions(+)
 create mode 100644 drivers/iio/light/al3320a.c
drivers/iio/light/Kconfig +10 -0
index bf05ca5..5bea821 100644
@@ -17,6 +17,16 @@ config ADJD_S311
 	 This driver can also be built as a module.  If so, the module
 	 will be called adjd_s311.
 
+config AL3320A
+	tristate "AL3320A ambient light sensor"
+	depends on I2C
+	help
+	 Say Y here if you want to build a driver for the Dyna Image AL3320A
+	 ambient light sensor.
+
+	 To compile this driver as a module, choose M here: the
+	 module will be called al3320a.
+
 config APDS9300
 	tristate "APDS9300 ambient light sensor"
 	depends on I2C
drivers/iio/light/Makefile +1 -0
index 8b8c09f..47877a3 100644
@@ -4,6 +4,7 @@
 
 # When adding new entries keep the list in alphabetical order
 obj-$(CONFIG_ADJD_S311)		+= adjd_s311.o
+obj-$(CONFIG_AL3320A)		+= al3320a.o
 obj-$(CONFIG_APDS9300)		+= apds9300.o
 obj-$(CONFIG_CM32181)		+= cm32181.o
 obj-$(CONFIG_CM36651)		+= cm36651.o
drivers/iio/light/al3320a.c new file +9 -0
new file mode 100644
index 0000000..787ce2e
@@ -0,0 +1,247 @@
+/*
+ * AL3320A - Dyna Image Ambient Light Sensor
+ *
+ * Copyright (c) 2014, Intel Corporation.
+ *
+ * This file is subject to the terms and conditions of version 2 of
+ * the GNU General Public License.  See the file COPYING in the main
+ * directory of this archive for more details.
+ *

drivers/iio/light/al3320a.c line 19

Quoted 10 lines
drivers/iio/light/al3320a.c new file +10 -0
+ * IIO driver for AL3320A (7-bit I2C slave address 0x1C).
+ *
+ * TODO: interrupt support
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>

mutex is not needed

drivers/iio/light/al3320a.c line 31

Quoted 12 lines
drivers/iio/light/al3320a.c new file +12 -0
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+#define AL3320A_DRV_NAME "al3320a"
+
+#define AL3320A_REG_CONFIG		0x00
+#define AL3320A_REG_STATUS		0x01
+#define AL3320A_REG_INT			0x02
+#define AL3320A_REG_WAIT		0x06
+#define AL3320A_REG_CONFIG_RANGE	0x07
+#define AL3320A_REG_PERSIST		0x08

PERSIST is not used, maybe add to TODO

drivers/iio/light/al3320a.c line 35

Quoted 4 lines
drivers/iio/light/al3320a.c new file +4 -0
+#define AL3320A_REG_MEAN_TIME		0x09
+#define AL3320A_REG_ADUMMY		0x0A
+#define AL3320A_REG_DATA_LOW		0x22
+#define AL3320A_REG_DATA_HIGH		0x23

DATA_HIGH became unused by read_word_swapped()

drivers/iio/light/al3320a.c line 40

Quoted 5 lines
drivers/iio/light/al3320a.c new file +5 -0
+
+#define AL3320A_REG_LOW_THRESH_LOW	0x30
+#define AL3320A_REG_LOW_THRESH_HIGH	0x31
+#define AL3320A_REG_HIGH_THRESH_LOW	0x32
+#define AL3320A_REG_HIGH_THRESH_HIGH	0x33

threshold are TODO

drivers/iio/light/al3320a.c line 44

Quoted 4 lines
drivers/iio/light/al3320a.c new file +4 -0
+
+#define AL3320A_CONFIG_DISABLE		0x00
+#define AL3320A_CONFIG_ENABLE		BIT(0)
+#define AL3320A_CONFIG_SW_RESET		BIT(2)

SW_RESET is unused

Quoted 124 lines
drivers/iio/light/al3320a.c new file +124 -0
+
+#define AL3320A_GAIN_SHIFT		1
+
+/* chip params default values */
+#define AL3320A_DEFAULT_MEAN_TIME	4
+#define AL3320A_DEFAULT_WAIT_TIME	0 /* no waiting */
+
+enum al3320a_range {
+	AL3320A_RANGE_1, /* 33.28K lux */
+	AL3320A_RANGE_2, /* 8.32K lux  */
+	AL3320A_RANGE_3, /* 2.08K lux  */
+	AL3320A_RANGE_4  /* 0.65K lux  */
+};
+
+static const int al3320a_scales[][2] = {
+	{0, 512000}, {0, 128000}, {0, 32000}, {0, 10000}
+};
+
+struct al3320a_data {
+	struct i2c_client *client;
+	u8 range;
+};
+
+static const struct iio_chan_spec al3320a_channels[] = {
+	{
+		.type	= IIO_LIGHT,
+		.info_mask_separate =
+			BIT(IIO_CHAN_INFO_RAW) |
+			BIT(IIO_CHAN_INFO_SCALE),
+	}
+};
+
+static int al3320a_enable(struct al3320a_data *data)
+{
+	return i2c_smbus_write_byte_data(data->client, AL3320A_REG_CONFIG,
+					 AL3320A_CONFIG_ENABLE);
+}
+
+static int al3320a_disable(struct al3320a_data *data)
+{
+	return i2c_smbus_write_byte_data(data->client, AL3320A_REG_CONFIG,
+					 AL3320A_CONFIG_DISABLE);
+}
+
+static int al3320a_set_config_range(struct al3320a_data *data, u8 gain)
+{
+	int ret;
+
+	ret = i2c_smbus_write_byte_data(data->client, AL3320A_REG_CONFIG_RANGE,
+					 gain << AL3320A_GAIN_SHIFT);
+	if (ret >= 0)
+		data->range = gain;
+	return ret;
+}
+
+static int al3320a_set_mean_time(struct al3320a_data *data, u8 mean_time)
+{
+	return i2c_smbus_write_byte_data(data->client, AL3320A_REG_MEAN_TIME,
+					 mean_time);
+}
+
+static int al3320a_set_wait_time(struct al3320a_data *data, u8 wait_time)
+{
+	return i2c_smbus_write_byte_data(data->client, AL3320A_REG_WAIT,
+					 wait_time);
+}
+
+static int al3320a_get_adc_value(struct al3320a_data *data)
+{
+	return i2c_smbus_read_word_swapped(data->client, AL3320A_REG_DATA_LOW);
+}
+
+static int al3320a_init(struct al3320a_data *data)
+{
+	int ret;
+
+	/* power on */
+	ret = al3320a_enable(data);
+	if (ret)
+		return ret;
+
+	ret = al3320a_set_config_range(data, AL3320A_RANGE_3);
+	if (ret)
+		return ret;
+
+	ret = al3320a_set_mean_time(data, AL3320A_DEFAULT_MEAN_TIME);
+	if (ret)
+		return ret;
+
+	ret = al3320a_set_wait_time(data, AL3320A_DEFAULT_WAIT_TIME);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int al3320a_read_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int *val,
+			    int *val2,
+			    long mask)
+{
+	struct al3320a_data *data = iio_priv(indio_dev);
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = al3320a_get_adc_value(data);
+		if (ret < 0)
+			return ret;
+		*val = ret;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		*val = al3320a_scales[data->range][0];
+		*val2 = al3320a_scales[data->range][1];
+		return IIO_VAL_INT_PLUS_MICRO;
+	}
+	return -EINVAL;
+}
+
+static int al3320a_write_raw(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan,
+			     int val, int val2, long mask)
+{

drivers/iio/light/al3320a.c line 178

Quoted 10 lines
drivers/iio/light/al3320a.c new file +10 -0
+	struct al3320a_data *data = iio_priv(indio_dev);
+	int i;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		for (i = 0; i < ARRAY_SIZE(al3320a_scales); i++) {
+			if (val == al3320a_scales[i][0] &&
+			    val2 == al3320a_scales[i][1])
+				return al3320a_set_config_range(data, i);
+		}

could add a break; here so it is not missed when handling more masks

Quoted 37 lines
drivers/iio/light/al3320a.c new file +37 -0
+	}
+	return -EINVAL;
+}
+
+static const struct iio_info al3320a_info = {
+	.driver_module	= THIS_MODULE,
+	.read_raw	= al3320a_read_raw,
+	.write_raw	= al3320a_write_raw,
+};
+
+static int al3320a_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct al3320a_data *data;
+	struct iio_dev *indio_dev;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	i2c_set_clientdata(client, indio_dev);
+	data->client = client;
+
+	indio_dev->dev.parent = &client->dev;
+	indio_dev->info = &al3320a_info;
+	indio_dev->name = AL3320A_DRV_NAME;
+	indio_dev->channels = al3320a_channels;
+	indio_dev->num_channels = ARRAY_SIZE(al3320a_channels);
+	indio_dev->modes = INDIO_DIRECT_MODE;
+
+	ret = al3320a_init(data);
+	if (ret) {
+		dev_err(&client->dev, "al3320a chip init failed\n");
+		return ret;
+	}

drivers/iio/light/al3320a.c line 225

Quoted 10 lines
drivers/iio/light/al3320a.c new file +10 -0
+
+	return devm_iio_device_register(&client->dev, indio_dev);
+}
+
+static int al3320a_remove(struct i2c_client *client)
+{
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
+	struct al3320a_data *data = iio_priv(indio_dev);
+
+	return  al3320a_disable(data);

extra space before al3320a_disable()

Quoted 23 lines
drivers/iio/light/al3320a.c new file +22 -0
+}
+
+static const struct i2c_device_id al3320a_id[] = {
+	{"al3320a", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, al3320a_id);
+
+static struct i2c_driver al3320a_driver = {
+	.driver = {
+		.name = AL3320A_DRV_NAME,
+	},
+	.probe		= al3320a_probe,
+	.remove		= al3320a_remove,
+	.id_table	= al3320a_id,
+};
+
+module_i2c_driver(al3320a_driver);
+
+MODULE_AUTHOR("Daniel Baluta <[email protected]>");
+MODULE_DESCRIPTION("AL3320A Ambient Light Sensor driver");
+MODULE_LICENSE("GPL v2");
Signature · 2 lines
Peter Meerwald
+43-664-2444418 (mobile)
#2 lore raw
Quoted 76 lines · Peter Meerwald
Quoted 7 lines

Minimal implementation. This driver provides raw illuminance readings.

This is based on drivers/hwmon/al3320.c (*) driver from msm tree written by Tsechih Lin <[email protected]>

* https://android.googlesource.com/kernel/msm.git

some more comments on minor things below...

Quoted 66 lines

---
Changes since v1: (reported by Peter Meerwald)
* used u8 instead of int for passing gain and mean_time
* used i2c_smbus_read_word_swapped instead of 2 x i2c_smbus_read_byte_data
* used devm_iio_device_register instead of iio_device_register
* small style fixes

 drivers/iio/light/Kconfig   |  10 ++
 drivers/iio/light/Makefile  |   1 +
 drivers/iio/light/al3320a.c | 247 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 258 insertions(+)
 create mode 100644 drivers/iio/light/al3320a.c
drivers/iio/light/Kconfig +10 -0
index bf05ca5..5bea821 100644
@@ -17,6 +17,16 @@ config ADJD_S311
       This driver can also be built as a module.  If so, the module
       will be called adjd_s311.
 
+config AL3320A
+     tristate "AL3320A ambient light sensor"
+     depends on I2C
+     help
+      Say Y here if you want to build a driver for the Dyna Image AL3320A
+      ambient light sensor.
+
+      To compile this driver as a module, choose M here: the
+      module will be called al3320a.
+
 config APDS9300
      tristate "APDS9300 ambient light sensor"
      depends on I2C
drivers/iio/light/Makefile +1 -0
index 8b8c09f..47877a3 100644
@@ -4,6 +4,7 @@
 
 # When adding new entries keep the list in alphabetical order
 obj-$(CONFIG_ADJD_S311)              += adjd_s311.o
+obj-$(CONFIG_AL3320A)                += al3320a.o
 obj-$(CONFIG_APDS9300)               += apds9300.o
 obj-$(CONFIG_CM32181)                += cm32181.o
 obj-$(CONFIG_CM36651)                += cm36651.o
drivers/iio/light/al3320a.c new file +13 -0
new file mode 100644
index 0000000..787ce2e
@@ -0,0 +1,247 @@
+/*
+ * AL3320A - Dyna Image Ambient Light Sensor
+ *
+ * Copyright (c) 2014, Intel Corporation.
+ *
+ * This file is subject to the terms and conditions of version 2 of
+ * the GNU General Public License.  See the file COPYING in the main
+ * directory of this archive for more details.
+ *
+ * IIO driver for AL3320A (7-bit I2C slave address 0x1C).
+ *
+ * TODO: interrupt support
+ *
Quoted 8 lines

drivers/iio/light/al3320a.c line 19

Quoted 6 lines
drivers/iio/light/al3320a.c new file +6 -0
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>

mutex is not needed

Correct. To be fixed in v3.

Quoted 15 lines

drivers/iio/light/al3320a.c line 31

Quoted 13 lines
drivers/iio/light/al3320a.c new file +12 -0
+
+#include <linux/iio/iio.h>
+#include <linux/iio/sysfs.h>
+
+#define AL3320A_DRV_NAME "al3320a"
+
+#define AL3320A_REG_CONFIG           0x00
+#define AL3320A_REG_STATUS           0x01
+#define AL3320A_REG_INT                      0x02
+#define AL3320A_REG_WAIT             0x06
+#define AL3320A_REG_CONFIG_RANGE     0x07
+#define AL3320A_REG_PERSIST          0x08

PERSIST is not used, maybe add to TODO

Hmm, I think PERSIST is an internal part of interrupt support which is already listed in TODO list.

Quoted 7 lines

drivers/iio/light/al3320a.c line 35

Quoted 5 lines
drivers/iio/light/al3320a.c new file +4 -0
+#define AL3320A_REG_MEAN_TIME                0x09
+#define AL3320A_REG_ADUMMY           0x0A
+#define AL3320A_REG_DATA_LOW         0x22
+#define AL3320A_REG_DATA_HIGH                0x23

DATA_HIGH became unused by read_word_swapped()

Ok, removed in v3. I've seen that it is a common practice to define only used registers. Anyhow, I think that drivers would be easier to understand/maintain if all register definitions are listed from start.

Quoted 8 lines

drivers/iio/light/al3320a.c line 40

Quoted 6 lines
drivers/iio/light/al3320a.c new file +5 -0
+
+#define AL3320A_REG_LOW_THRESH_LOW   0x30
+#define AL3320A_REG_LOW_THRESH_HIGH  0x31
+#define AL3320A_REG_HIGH_THRESH_LOW  0x32
+#define AL3320A_REG_HIGH_THRESH_HIGH 0x33

threshold are TODO

ok.

Quoted 7 lines

drivers/iio/light/al3320a.c line 44

Quoted 5 lines
drivers/iio/light/al3320a.c new file +4 -0
+
+#define AL3320A_CONFIG_DISABLE               0x00
+#define AL3320A_CONFIG_ENABLE                BIT(0)
+#define AL3320A_CONFIG_SW_RESET              BIT(2)

SW_RESET is unused

Removed in v3.

Quoted 129 lines
Quoted 129 lines
drivers/iio/light/al3320a.c new file +128 -0
+
+#define AL3320A_GAIN_SHIFT           1
+
+/* chip params default values */
+#define AL3320A_DEFAULT_MEAN_TIME    4
+#define AL3320A_DEFAULT_WAIT_TIME    0 /* no waiting */
+
+enum al3320a_range {
+     AL3320A_RANGE_1, /* 33.28K lux */
+     AL3320A_RANGE_2, /* 8.32K lux  */
+     AL3320A_RANGE_3, /* 2.08K lux  */
+     AL3320A_RANGE_4  /* 0.65K lux  */
+};
+
+static const int al3320a_scales[][2] = {
+     {0, 512000}, {0, 128000}, {0, 32000}, {0, 10000}
+};
+
+struct al3320a_data {
+     struct i2c_client *client;
+     u8 range;
+};
+
+static const struct iio_chan_spec al3320a_channels[] = {
+     {
+             .type   = IIO_LIGHT,
+             .info_mask_separate =
+                     BIT(IIO_CHAN_INFO_RAW) |
+                     BIT(IIO_CHAN_INFO_SCALE),
+     }
+};
+
+static int al3320a_enable(struct al3320a_data *data)
+{
+     return i2c_smbus_write_byte_data(data->client, AL3320A_REG_CONFIG,
+                                      AL3320A_CONFIG_ENABLE);
+}
+
+static int al3320a_disable(struct al3320a_data *data)
+{
+     return i2c_smbus_write_byte_data(data->client, AL3320A_REG_CONFIG,
+                                      AL3320A_CONFIG_DISABLE);
+}
+
+static int al3320a_set_config_range(struct al3320a_data *data, u8 gain)
+{
+     int ret;
+
+     ret = i2c_smbus_write_byte_data(data->client, AL3320A_REG_CONFIG_RANGE,
+                                      gain << AL3320A_GAIN_SHIFT);
+     if (ret >= 0)
+             data->range = gain;
+     return ret;
+}
+
+static int al3320a_set_mean_time(struct al3320a_data *data, u8 mean_time)
+{
+     return i2c_smbus_write_byte_data(data->client, AL3320A_REG_MEAN_TIME,
+                                      mean_time);
+}
+
+static int al3320a_set_wait_time(struct al3320a_data *data, u8 wait_time)
+{
+     return i2c_smbus_write_byte_data(data->client, AL3320A_REG_WAIT,
+                                      wait_time);
+}
+
+static int al3320a_get_adc_value(struct al3320a_data *data)
+{
+     return i2c_smbus_read_word_swapped(data->client, AL3320A_REG_DATA_LOW);
+}
+
+static int al3320a_init(struct al3320a_data *data)
+{
+     int ret;
+
+     /* power on */
+     ret = al3320a_enable(data);
+     if (ret)
+             return ret;
+
+     ret = al3320a_set_config_range(data, AL3320A_RANGE_3);
+     if (ret)
+             return ret;
+
+     ret = al3320a_set_mean_time(data, AL3320A_DEFAULT_MEAN_TIME);
+     if (ret)
+             return ret;
+
+     ret = al3320a_set_wait_time(data, AL3320A_DEFAULT_WAIT_TIME);
+     if (ret)
+             return ret;
+
+     return 0;
+}
+
+static int al3320a_read_raw(struct iio_dev *indio_dev,
+                         struct iio_chan_spec const *chan,
+                         int *val,
+                         int *val2,
+                         long mask)
+{
+     struct al3320a_data *data = iio_priv(indio_dev);
+     int ret;
+
+     switch (mask) {
+     case IIO_CHAN_INFO_RAW:
+             ret = al3320a_get_adc_value(data);
+             if (ret < 0)
+                     return ret;
+             *val = ret;
+             return IIO_VAL_INT;
+     case IIO_CHAN_INFO_SCALE:
+             *val = al3320a_scales[data->range][0];
+             *val2 = al3320a_scales[data->range][1];
+             return IIO_VAL_INT_PLUS_MICRO;
+     }
+     return -EINVAL;
+}
+
+static int al3320a_write_raw(struct iio_dev *indio_dev,
+                          struct iio_chan_spec const *chan,
+                          int val, int val2, long mask)
+{
+     struct al3320a_data *data = iio_priv(indio_dev);
+     int i;
+
+     switch (mask) {
Quoted 8 lines

drivers/iio/light/al3320a.c line 178

Quoted 6 lines
drivers/iio/light/al3320a.c new file +6 -0
+     case IIO_CHAN_INFO_SCALE:
+             for (i = 0; i < ARRAY_SIZE(al3320a_scales); i++) {
+                     if (val == al3320a_scales[i][0] &&
+                         val2 == al3320a_scales[i][1])
+                             return al3320a_set_config_range(data, i);
+             }

could add a break; here so it is not missed when handling more masks

Fixed in v3.

Quoted 42 lines
Quoted 42 lines
drivers/iio/light/al3320a.c new file +41 -0
+     }
+     return -EINVAL;
+}
+
+static const struct iio_info al3320a_info = {
+     .driver_module  = THIS_MODULE,
+     .read_raw       = al3320a_read_raw,
+     .write_raw      = al3320a_write_raw,
+};
+
+static int al3320a_probe(struct i2c_client *client,
+                      const struct i2c_device_id *id)
+{
+     struct al3320a_data *data;
+     struct iio_dev *indio_dev;
+     int ret;
+
+     indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
+     if (!indio_dev)
+             return -ENOMEM;
+
+     data = iio_priv(indio_dev);
+     i2c_set_clientdata(client, indio_dev);
+     data->client = client;
+
+     indio_dev->dev.parent = &client->dev;
+     indio_dev->info = &al3320a_info;
+     indio_dev->name = AL3320A_DRV_NAME;
+     indio_dev->channels = al3320a_channels;
+     indio_dev->num_channels = ARRAY_SIZE(al3320a_channels);
+     indio_dev->modes = INDIO_DIRECT_MODE;
+
+     ret = al3320a_init(data);
+     if (ret) {
+             dev_err(&client->dev, "al3320a chip init failed\n");
+             return ret;
+     }
+
+     return devm_iio_device_register(&client->dev, indio_dev);
+}
+
Quoted 8 lines

drivers/iio/light/al3320a.c line 225

Quoted 6 lines
drivers/iio/light/al3320a.c new file +6 -0
+static int al3320a_remove(struct i2c_client *client)
+{
+     struct iio_dev *indio_dev = i2c_get_clientdata(client);
+     struct al3320a_data *data = iio_priv(indio_dev);
+
+     return  al3320a_disable(data);

extra space before al3320a_disable()

Good catch. Fixed in v3.

Quoted 27 lines
Quoted 14 lines
drivers/iio/light/al3320a.c new file +12 -0
+}
+
+static const struct i2c_device_id al3320a_id[] = {
+     {"al3320a", 0},
+     {}
+};
+MODULE_DEVICE_TABLE(i2c, al3320a_id);
+
+static struct i2c_driver al3320a_driver = {
+     .driver = {
+             .name = AL3320A_DRV_NAME,
+     },

drivers/iio/light/al3320a.c line 247

Quoted 10 lines
drivers/iio/light/al3320a.c new file +10 -0
+     .probe          = al3320a_probe,
+     .remove         = al3320a_remove,
+     .id_table       = al3320a_id,
+};
+
+module_i2c_driver(al3320a_driver);
+
+MODULE_AUTHOR("Daniel Baluta <[email protected]>");
+MODULE_DESCRIPTION("AL3320A Ambient Light Sensor driver");
+MODULE_LICENSE("GPL v2");

--

Quoted 1 line

Peter Meerwald

Thanks again Peter.