arm: omap: tao3530: Add pdata-quirk for the mmc2 internal clock
Subsystems (5)
PATCH v2 1/4 arm: omap: tao3530: Add pdata-quirk for the mmc2 internal clock
Set internal clock source for MMC2 on tao3530.
---
v2:
- Patch description added to commit text
arch/arm/mach-omap2/pdata-quirks.c | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm/mach-omap2/pdata-quirks.c +6 -0
@@ -253,6 +253,11 @@ static void __init nokia_n900_legacy_init(void) } } + +static void __init omap3_tao3530_legacy_init (void ) +{ +hsmmc2_internal_input_clk (); +}#endif /* CONFIG_ARCH_OMAP3 */ #ifdef CONFIG_ARCH_OMAP4
@@ -377,6 +382,7 @@ static struct pdata_init pdata_quirks[] __initdata = { { "ti,omap3-evm-37xx", omap3_evm_legacy_init, }, { "ti,omap3-zoom3", omap3_zoom_legacy_init, }, { "ti,am3517-evm", am3517_evm_legacy_init, }, + { "technexion,omap3-tao3530", omap3_tao3530_legacy_init, }, #endif #ifdef CONFIG_ARCH_OMAP4 { "ti,omap4-sdp", omap4_sdp_legacy_init, },
Signature · 1 line
2.1.0
PATCH v2 2/4 arm: omap3: Add Technexion TAO3530 SOM omap3-tao3530.dtsi
The Technexion TAO3530 is a OMAP3530 based SOM. This patch adds the basic support for it as an dtsi file which can be included by baseboard equipped with this SOM. E.g. the Technexion Thunder baseboard.
---
v2:
- Used OMAP3_CORE1_IOPAD macros for all mux entries
- Added ranges entry to gpmc node
- Added gpmc,device-width = <2> to nand dt node. Otherwise NAND probing would not work
arch/arm/boot/dts/omap3-tao3530.dtsi | 337 +++++++++++++++++++++++++++++++++++ 1 file changed, 337 insertions(+) create mode 100644 arch/arm/boot/dts/omap3-tao3530.dtsi
arch/arm/boot/dts/omap3-tao3530.dtsi new file +337 -0
@@ -0,0 +1,337 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2014 Stefan Roese <[email protected]> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap34xx-hs.dtsi" + +/ { + cpus { + cpu at 0 { + cpu0-supply = <&vcc>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; /* gpio_162 */ + vcc-supply = <&hsusb2_power>; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "omap3beagle"; + + /* McBSP2 is used for onboard sound, same as on beagle */ + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; + + /* Regulator to enable/switch the vcc of the Wifi module */ + mmc2_sdio_poweron: regulator-mmc2-sdio-poweron { + compatible = "regulator-fixed"; + regulator-name = "regulator-mmc2-sdio-poweron"; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3150000>; + gpio = <&gpio5 29 GPIO_ACTIVE_LOW>; /* gpio_157 */ + enable-active-low; + startup-delay-us = <10000>; + }; +}; + +&omap3_pmx_core { + hsusbb2_pins: pinmux_hsusbb2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3_CORE1_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3_CORE1_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3_CORE1_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3_CORE1_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3_CORE1_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ + OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ + OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ + OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + >; + }; + + /* wlan GPIO output for WLAN_EN */ + wlan_gpio: pinmux_wlan_gpio { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr gpio_157 */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl.i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda.i2c3_sda */ + >; + }; + + mcspi1_pins: pinmux_mcspi1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ + >; + }; + + mcspi3_pins: pinmux_mcspi3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x25dc, PIN_OUTPUT | MUX_MODE1) /* etk_d0.mcspi3_simo gpio14 INPUT | MODE1 */ + OMAP3_CORE1_IOPAD(0x25de, PIN_INPUT_PULLUP | MUX_MODE1) /* etk_d1.mcspi3_somi gpio15 INPUT | MODE1 */ + OMAP3_CORE1_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE1) /* etk_d2.mcspi3_cs0 gpio16 INPUT | MODE1 */ + OMAP3_CORE1_IOPAD(0x25e2, PIN_INPUT | MUX_MODE1) /* etk_d3.mcspi3_clk gpio17 INPUT | MODE1 */ + >; + }; + + mcbsp3_pins: pinmux_mcbsp3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x216c, PIN_OUTPUT | MUX_MODE0) /* mcbsp3_dx.uart2_cts */ + OMAP3_CORE1_IOPAD(0x216e, PIN_INPUT | MUX_MODE0) /* mcbsp3_dr.uart2_rts */ + OMAP3_CORE1_IOPAD(0x2170, PIN_INPUT | MUX_MODE0) /* mcbsp3_clk.uart2_tx */ + OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE0) /* mcbsp3_fsx.uart2_rx */ + >; + }; +}; + +/* McBSP1: mux'ed with GPIO158 as clock for HA-DSP */ +&mcbsp1 { + status = "disabled"; +}; + +&mcbsp2 { + status = "okay"; +}; + +&i2c1 { + clock-frequency = <2600000>; + + twl: twl at 48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; +}; + +&mcspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi1_pins>; + + spidev at 0 { + compatible = "spidev"; + spi-max-frequency = <48000000>; + reg = <0>; + spi-cpha; + }; +}; + +&mcspi3 { + pinctrl-names = "default"; + pinctrl-0 = <&mcspi3_pins>; + + spidev at 0 { + compatible = "spidev"; + spi-max-frequency = <48000000>; + reg = <0>; + spi-cpha; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + vmmc_aux-supply = <&vsim>; + cd-gpios = <&twl_gpio 0 0>; + bus-width = <8>; +}; + +// WiFi (Marvell 88W8686) on MMC2/SDIO +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&mmc2_sdio_poweron>; + non-removable; + bus-width = <4>; + cap-power-off-card; +}; + +&mmc3 { + status = "disabled"; +}; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + +&twl_gpio { + ti,use-leds; + /* pullups: BIT(1) */ + ti,pullups = <0x000002>; + /* + * pulldowns: + * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13) + * BIT(15), BIT(16), BIT(17) + */ + ti,pulldowns = <0x03a1c4>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&mcbsp3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp3_pins>; +}; + +&gpmc { + ranges = <0 0 0x00000000 0x01000000>; + + nand at 0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + nand-bus-width = <16>; + gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */ + ti,nand-ecc-opt = "sw"; + + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <36>; + gpmc,cs-wr-off-ns = <36>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <24>; + gpmc,adv-wr-off-ns = <36>; + gpmc,oe-on-ns = <6>; + gpmc,oe-off-ns = <48>; + gpmc,we-on-ns = <6>; + gpmc,we-off-ns = <30>; + gpmc,rd-cycle-ns = <72>; + gpmc,wr-cycle-ns = <72>; + gpmc,access-ns = <54>; + gpmc,wr-access-ns = <30>; + + #address-cells = <1>; + #size-cells = <1>; + + x-loader at 0 { + label = "X-Loader"; + reg = <0 0x80000>; + }; + + bootloaders at 80000 { + label = "U-Boot"; + reg = <0x80000 0x1e0000>; + }; + + bootloaders_env at 260000 { + label = "U-Boot Env"; + reg = <0x260000 0x20000>; + }; + + kernel at 280000 { + label = "Kernel"; + reg = <0x280000 0x400000>; + }; + + filesystem at 680000 { + label = "File System"; + reg = <0x680000 0xf980000>; + }; + }; +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&vaux2 { + regulator-name = "vdd_ehci"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; +};
Signature · 1 line
2.1.0
PATCH v2 3/4 arm: omap3: Add Technexion Thunder support (TAO3530 SOM based)
In reply to Stefan RoeseThis baseboard is equipped with the Technexion TAO35030 SOM. So includes this dtsi. Some Thunder specific features are:
- LCD panel
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/omap3-thunder.dts | 129 ++++++++++++++++++++++++++++++++++++ 2 files changed, 130 insertions(+) create mode 100644 arch/arm/boot/dts/omap3-thunder.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -309,6 +309,7 @@ dtb-$(CONFIG_ARCH_OMAP3) += am3517-craneboard.dtb \ omap3-sbc-t3517.dtb \ omap3-sbc-t3530.dtb \ omap3-sbc-t3730.dtb \ + omap3-thunder.dtb \ omap3-zoom3.dtb dtb-$(CONFIG_SOC_AM33XX) += am335x-base0033.dtb \ am335x-bone.dtb \
arch/arm/boot/dts/omap3-thunder.dts new file +129 -0
129 lines not on this page · raw message
Signature · 1 line
2.1.0
PATCH v2 4/4 arm: omap3: Add HEAD acoustics omap3-ha.dts and omap3-ha-lcd.dts (TAO3530 based)
In reply to Stefan RoeseThese baseboards are equipped with the Technexion TAO35030 SOM. So they include this dtsi. The common parts are extracted into an "common" dtsi file. The main difference between both boards is, that the *lcd has DSS support enabled for the LCD.
Some HEAD acoustics specific features are:
- LED handling
- Special FPGA/DSP audio driver (not included in this series)
- powerdown GPIO
---
v2:
- Used OMAP3_CORE1_IOPAD macros for all mux entries
arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/omap3-ha-common.dtsi | 88 ++++++++++++++++++ arch/arm/boot/dts/omap3-ha-lcd.dts | 165 +++++++++++++++++++++++++++++++++ arch/arm/boot/dts/omap3-ha.dts | 28 ++++++ 4 files changed, 283 insertions(+) create mode 100644 arch/arm/boot/dts/omap3-ha-common.dtsi create mode 100644 arch/arm/boot/dts/omap3-ha-lcd.dts create mode 100644 arch/arm/boot/dts/omap3-ha.dts
arch/arm/boot/dts/Makefile +2 -0
@@ -287,6 +287,8 @@ dtb-$(CONFIG_ARCH_OMAP3) += am3517-craneboard.dtb \ omap3-evm.dtb \ omap3-evm-37xx.dtb \ omap3-gta04.dtb \ + omap3-ha.dtb \ + omap3-ha-lcd.dtb \ omap3-igep0020.dtb \ omap3-igep0030.dtb \ omap3-ldp.dtb \
arch/arm/boot/dts/omap3-ha-common.dtsi new file +88 -0
88 lines not on this page · raw message
arch/arm/boot/dts/omap3-ha-lcd.dts new file +165 -0
165 lines not on this page · raw message
arch/arm/boot/dts/omap3-ha.dts new file +28 -0
@@ -0,0 +1,28 @@ +/* + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ + * Copyright (C) 2014 Stefan Roese <[email protected]> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "omap3-ha-common.dtsi" + +/ { + model = "TI OMAP3 HEAD acoustics baseboard with TAO3530 SOM"; + compatible = "headacoustics,omap3-ha", "technexion,omap3-tao3530", "ti,omap34xx", "ti,omap3"; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb2_pins + &powerdown_input_pins + &fpga_boot0_pins + &fpga_boot1_pins + &led_blue_pins + &led_green_pins + &led_red_pins + >; +};
Signature · 1 line
2.1.0
Tony Lindgren
maintainerPATCH v2 1/4 arm: omap: tao3530: Add pdata-quirk for the mmc2 internal clock
In reply to Stefan RoeseQuoted 9 lines · Stefan Roese
Set internal clock source for MMC2 on tao3530.
Signed-off-by Stefan Roese <[email protected]>Cc Thorsten Eisbein <[email protected]>Cc Tapani Utriainen <[email protected]>Cc Tony Lindgren <[email protected]>---
v2:
- Patch description added to commit text
Applying all into omap-for-v3.18/dt thanks.
Tony
Quoted 30 lines
arch/arm/mach-omap2/pdata-quirks.c | 6 ++++++ 1 file changed, 6 insertions(+)arch/arm/mach-omap2/pdata-quirks.c +6
-0@@ -253,6 +253,11 @@ static void __init nokia_n900_legacy_init(void) } } + +static void __init omap3_tao3530_legacy_init (void ) +{ +hsmmc2_internal_input_clk (); +}#endif /* CONFIG_ARCH_OMAP3 */ #ifdef CONFIG_ARCH_OMAP4 @@ -377,6 +382,7 @@ static struct pdata_init pdata_quirks[] __initdata = { { "ti,omap3-evm-37xx", omap3_evm_legacy_init, }, { "ti,omap3-zoom3", omap3_zoom_legacy_init, }, { "ti,am3517-evm", am3517_evm_legacy_init, }, + { "technexion,omap3-tao3530", omap3_tao3530_legacy_init, }, #endif #ifdef CONFIG_ARCH_OMAP4 { "ti,omap4-sdp", omap4_sdp_legacy_init, },Signature · 1 line
2.1.0