iMX6Q/DL:SABREAUTO/SABRESD: Move DDR and FDT configs to defconfig
PATCH 1/5 iMX6Q/DL:SABREAUTO/SABRESD: Move DDR and FDT configs to defconfig
To support more iMX6 variants,
1. Make the DDR size configurable based on the defconfig file
2. Make the FDT file configurable based on the defconfig file
--- board/freescale/mx6qsabreauto/mx6qsabreauto.c | 2 +- board/freescale/mx6sabresd/mx6sabresd.c | 2 +- configs/mx6dlsabreauto_defconfig | 2 +- configs/mx6dlsabresd_defconfig | 2 +- configs/mx6qsabreauto_defconfig | 2 +- configs/mx6qsabresd_defconfig | 2 +- include/configs/mx6qsabreauto.h | 9 ++------- include/configs/mx6sabresd.h | 8 +------- 8 files changed, 9 insertions(+), 20 deletions(-)
board/freescale/mx6qsabreauto/mx6qsabreauto.c +1 -1
@@ -45,7 +45,7 @@ DECLARE_GLOBAL_DATA_PTR;int dram_init (void ) { - gd->ram_size =get_ram_size ((void *)PHYS_SDRAM ,PHYS_SDRAM_SIZE ); + gd->ram_size = (phys_size_t )CONFIG_DDR_MB *1024 *1024 ;return 0 ; }
board/freescale/mx6sabresd/mx6sabresd.c +1 -1
@@ -53,7 +53,7 @@ DECLARE_GLOBAL_DATA_PTR;int dram_init (void ) { - gd->ram_size =get_ram_size ((void *)PHYS_SDRAM ,PHYS_SDRAM_SIZE ); + gd->ram_size = (phys_size_t )CONFIG_DDR_MB *1024 *1024 ;return 0 ; }
configs/mx6dlsabreauto_defconfig +1 -1
@@ -1,3 +1,3 @@ -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/mx6dl.cfg,MX6DL" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/mx6dl.cfg,MX6DL,DEFAULT_FDT_FILE=\"imx6dl-sabreauto.dtb\",DDR_MB=2048" CONFIG_ARM=y CONFIG_TARGET_MX6QSABREAUTO=y
configs/mx6dlsabresd_defconfig +1 -1
@@ -1,3 +1,3 @@ -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DEFAULT_FDT_FILE=\"imx6dl-sabresd.dtb\",DDR_MB=1024" CONFIG_ARM=y CONFIG_TARGET_MX6SABRESD=y
configs/mx6qsabreauto_defconfig +1 -1
@@ -1,3 +1,3 @@ -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6Q" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6Q,DEFAULT_FDT_FILE=\"imx6q-sabreauto.dtb\",DDR_MB=2048" CONFIG_ARM=y CONFIG_TARGET_MX6QSABREAUTO=y
configs/mx6qsabresd_defconfig +1 -1
@@ -1,3 +1,3 @@ -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q,DEFAULT_FDT_FILE=\"imx6q-sabresd.dtb\",DDR_MB=1024" CONFIG_ARM=y CONFIG_TARGET_MX6SABRESD=y
include/configs/mx6qsabreauto.h +2 -7
@@ -1,5 +1,5 @@/* -* Copyright (C) 2012 Freescale Semiconductor, Inc. +* Copyright (C) 2014 Freescale Semiconductor, Inc. * * Configuration settings for the Freescale i.MX6Q SabreAuto board. *
@@ -12,13 +12,8 @@#define CONFIG_MACH_TYPE 3529#define CONFIG_MXC_UART_BASE UART4_BASE#define CONFIG_CONSOLE_DEV "ttymxc3" -#if definedCONFIG_MX6Q -#define CONFIG_DEFAULT_FDT_FILE "imx6q-sabreauto.dtb" -#elif definedCONFIG_MX6DL -#define CONFIG_DEFAULT_FDT_FILE "imx6dl-sabreauto.dtb" -#endif +#define CONFIG_MMCROOT "/dev/mmcblk0p2" -#define PHYS_SDRAM_SIZE (2u * 1024 * 1024 * 1024)/* USB Configs */ #define CONFIG_CMD_USB
include/configs/mx6sabresd.h +1 -7
@@ -1,5 +1,5 @@/* -* Copyright (C) 2012 Freescale Semiconductor, Inc. +* Copyright (C) 2014 Freescale Semiconductor, Inc. * * Configuration settings for the Freescale i.MX6Q SabreSD board. *
@@ -16,12 +16,6 @@#define CONFIG_MXC_UART_BASE UART1_BASE#define CONFIG_CONSOLE_DEV "ttymxc0"#define CONFIG_MMCROOT "/dev/mmcblk1p2" -#if defined(CONFIG_MX6Q ) -#define CONFIG_DEFAULT_FDT_FILE "imx6q-sabresd.dtb" -#elif defined(CONFIG_MX6DL ) -#define CONFIG_DEFAULT_FDT_FILE "imx6dl-sabresd.dtb" -#endif -#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
Signature · 1 line
1.7.4.1
PATCH 2/5 iMX6Q:SABREAUTO: Rename the imximage.cfg to mx6q.cfg
Rename the imximage.cfg to mx6q.cfg.
No function change at all
--- board/freescale/mx6qsabreauto/imximage.cfg | 129 ---------------------------- board/freescale/mx6qsabreauto/mx6q.cfg | 129 ++++++++++++++++++++++++++++ configs/mx6qsabreauto_defconfig | 2 +- 3 files changed, 130 insertions(+), 130 deletions(-) delete mode 100644 board/freescale/mx6qsabreauto/imximage.cfg create mode 100644 board/freescale/mx6qsabreauto/mx6q.cfg
board/freescale/mx6qsabreauto/imximage.cfg deleted +0 -129
@@ -1,129 +0,0 @@ -/* - * Copyright (C) 2012 Freescale Semiconductor, Inc. - * - * SPDX-License-Identifier: GPL-2.0+ - * - * Refer doc/README.imximage for more details about how-to configure - * and create imximage boot image - * - * The syntax is taken as close as possible with the kwbimage - */ -/* image version */ - -IMAGE_VERSION 2 - -/* - * Boot Device : one of - * spi, sd (the board has no nand neither onenand) - */ -BOOT_FROM sd - -/* - * Device Configuration Data (DCD) - * - * Each entry must have the format: - * Addr-type Address Value - * - * where: - * Addr-type register length (1,2 or 4 bytes) - * Address absolute address of the register - * value value to be stored in the register - */ -DATA 4 0x020e0798 0x000C0000 -DATA 4 0x020e0758 0x00000000 -DATA 4 0x020e0588 0x00000030 -DATA 4 0x020e0594 0x00000030 -DATA 4 0x020e056c 0x00000030 -DATA 4 0x020e0578 0x00000030 -DATA 4 0x020e074c 0x00000030 -DATA 4 0x020e057c 0x00000030 -DATA 4 0x020e058c 0x00000000 -DATA 4 0x020e059c 0x00000030 -DATA 4 0x020e05a0 0x00000030 -DATA 4 0x020e078c 0x00000030 -DATA 4 0x020e0750 0x00020000 -DATA 4 0x020e05a8 0x00000028 -DATA 4 0x020e05b0 0x00000028 -DATA 4 0x020e0524 0x00000028 -DATA 4 0x020e051c 0x00000028 -DATA 4 0x020e0518 0x00000028 -DATA 4 0x020e050c 0x00000028 -DATA 4 0x020e05b8 0x00000028 -DATA 4 0x020e05c0 0x00000028 -DATA 4 0x020e0774 0x00020000 -DATA 4 0x020e0784 0x00000028 -DATA 4 0x020e0788 0x00000028 -DATA 4 0x020e0794 0x00000028 -DATA 4 0x020e079c 0x00000028 -DATA 4 0x020e07a0 0x00000028 -DATA 4 0x020e07a4 0x00000028 -DATA 4 0x020e07a8 0x00000028 -DATA 4 0x020e0748 0x00000028 -DATA 4 0x020e05ac 0x00000028 -DATA 4 0x020e05b4 0x00000028 -DATA 4 0x020e0528 0x00000028 -DATA 4 0x020e0520 0x00000028 -DATA 4 0x020e0514 0x00000028 -DATA 4 0x020e0510 0x00000028 -DATA 4 0x020e05bc 0x00000028 -DATA 4 0x020e05c4 0x00000028 -DATA 4 0x021b0800 0xa1390003 -DATA 4 0x021b080c 0x001F001F -DATA 4 0x021b0810 0x001F001F -DATA 4 0x021b480c 0x001F001F -DATA 4 0x021b4810 0x001F001F -DATA 4 0x021b083c 0x43260335 -DATA 4 0x021b0840 0x031A030B -DATA 4 0x021b483c 0x4323033B -DATA 4 0x021b4840 0x0323026F -DATA 4 0x021b0848 0x483D4545 -DATA 4 0x021b4848 0x44433E48 -DATA 4 0x021b0850 0x41444840 -DATA 4 0x021b4850 0x4835483E -DATA 4 0x021b081c 0x33333333 -DATA 4 0x021b0820 0x33333333 -DATA 4 0x021b0824 0x33333333 -DATA 4 0x021b0828 0x33333333 -DATA 4 0x021b481c 0x33333333 -DATA 4 0x021b4820 0x33333333 -DATA 4 0x021b4824 0x33333333 -DATA 4 0x021b4828 0x33333333 -DATA 4 0x021b08b8 0x00000800 -DATA 4 0x021b48b8 0x00000800 -DATA 4 0x021b0004 0x00020036 -DATA 4 0x021b0008 0x09444040 -DATA 4 0x021b000c 0x8A8F7955 -DATA 4 0x021b0010 0xFF328F64 -DATA 4 0x021b0014 0x01FF00DB -DATA 4 0x021b0018 0x00001740 -DATA 4 0x021b001c 0x00008000 -DATA 4 0x021b002c 0x000026d2 -DATA 4 0x021b0030 0x008F1023 -DATA 4 0x021b0040 0x00000047 -DATA 4 0x021b0000 0x841A0000 -DATA 4 0x021b001c 0x04088032 -DATA 4 0x021b001c 0x00008033 -DATA 4 0x021b001c 0x00048031 -DATA 4 0x021b001c 0x09408030 -DATA 4 0x021b001c 0x04008040 -DATA 4 0x021b0020 0x00005800 -DATA 4 0x021b0818 0x00011117 -DATA 4 0x021b4818 0x00011117 -DATA 4 0x021b0004 0x00025576 -DATA 4 0x021b0404 0x00011006 -DATA 4 0x021b001c 0x00000000 - -/* set the default clock gate to save power */ -DATA 4 0x020c4068 0x00C03F3F -DATA 4 0x020c406c 0x0030FC03 -DATA 4 0x020c4070 0x0FFFC000 -DATA 4 0x020c4074 0x3FF00000 -DATA 4 0x020c4078 0xFFFFF300 -DATA 4 0x020c407c 0x0F0000F3 -DATA 4 0x020c4080 0x00000FFF - -/* enable AXI cache for VDOA/VPU/IPU */ -DATA 4 0x020e0010 0xF00000CF -/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ -DATA 4 0x020e0018 0x007F007F -DATA 4 0x020e001c 0x007F007F
board/freescale/mx6qsabreauto/mx6q.cfg new file +129 -0
129 lines not on this page · raw message
configs/mx6qsabreauto_defconfig +1 -1
@@ -1,3 +1,3 @@ -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6Q,DEFAULT_FDT_FILE=\"imx6q-sabreauto.dtb\",DDR_MB=2048" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/mx6q.cfg,MX6Q,DEFAULT_FDT_FILE=\"imx6q-sabreauto.dtb\",DDR_MB=2048" CONFIG_ARM=y CONFIG_TARGET_MX6QSABREAUTO=y
Signature · 1 line
1.7.4.1
Fabio Estevam
reviewerPATCH 2/5 iMX6Q:SABREAUTO: Rename the imximage.cfg to mx6q.cfg
Quoted 7 lines · Ye.Li
Rename the imximage.cfg to mx6q.cfg.
No function change at allSigned-off-by Ye.Li <[email protected]>--- board/freescale/mx6qsabreauto/imximage.cfg | 129 ---------------------------- board/freescale/mx6qsabreauto/mx6q.cfg | 129 ++++++++++++++++++++++++++++
It would be better to use git format -M so that git can detect the file rename.
PATCH 2/5 iMX6Q:SABREAUTO: Rename the imximage.cfg to mx6q.cfg
Quoted 9 lines · Fabio Estevam
Quoted 7 lines · Ye.Li
Rename the imximage.cfg to mx6q.cfg.
No function change at allSigned-off-by Ye.Li <[email protected]>--- board/freescale/mx6qsabreauto/imximage.cfg | 129 ---------------------------- board/freescale/mx6qsabreauto/mx6q.cfg | 129 ++++++++++++++++++++++++++++It would be better to use git format -M so that git can detect the file rename.
Ok. Will change to use it in V2 patch.
Best regards,
Ye Li
PATCH 3/5 iMX6DL:SABRESD: Add new DDR script
In reply to Ye.LiAdd specified mx6dl_4x_mt41j128.cfg DDR script for iMX6DLSABRESD board. Not share from nitrogen6x. The default boot device also changes to SD card.
--- board/freescale/mx6sabresd/mx6dl_4x_mt41j128.cfg | 130 ++++++++++++++++++++++ configs/mx6dlsabresd_defconfig | 2 +- 2 files changed, 131 insertions(+), 1 deletions(-) create mode 100644 board/freescale/mx6sabresd/mx6dl_4x_mt41j128.cfg
board/freescale/mx6sabresd/mx6dl_4x_mt41j128.cfg new file +130 -0
@@ -0,0 +1,130 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * Jason Liu <[email protected]> + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer doc/README.imximage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* image version */ +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +DATA 4 0x020e0774 0x000C0000 +DATA 4 0x020e0754 0x00000000 +DATA 4 0x020e04ac 0x00000030 +DATA 4 0x020e04b0 0x00000030 +DATA 4 0x020e0464 0x00000030 +DATA 4 0x020e0490 0x00000030 +DATA 4 0x020e074c 0x00000030 +DATA 4 0x020e0494 0x00000030 +DATA 4 0x020e04a0 0x00000000 +DATA 4 0x020e04b4 0x00000030 +DATA 4 0x020e04b8 0x00000030 +DATA 4 0x020e076c 0x00000030 +DATA 4 0x020e0750 0x00020000 +DATA 4 0x020e04bc 0x00000030 +DATA 4 0x020e04c0 0x00000030 +DATA 4 0x020e04c4 0x00000030 +DATA 4 0x020e04c8 0x00000030 +DATA 4 0x020e04cc 0x00000030 +DATA 4 0x020e04d0 0x00000030 +DATA 4 0x020e04d4 0x00000030 +DATA 4 0x020e04d8 0x00000030 +DATA 4 0x020e0760 0x00020000 +DATA 4 0x020e0764 0x00000030 +DATA 4 0x020e0770 0x00000030 +DATA 4 0x020e0778 0x00000030 +DATA 4 0x020e077c 0x00000030 +DATA 4 0x020e0780 0x00000030 +DATA 4 0x020e0784 0x00000030 +DATA 4 0x020e078c 0x00000030 +DATA 4 0x020e0748 0x00000030 +DATA 4 0x020e0470 0x00000030 +DATA 4 0x020e0474 0x00000030 +DATA 4 0x020e0478 0x00000030 +DATA 4 0x020e047c 0x00000030 +DATA 4 0x020e0480 0x00000030 +DATA 4 0x020e0484 0x00000030 +DATA 4 0x020e0488 0x00000030 +DATA 4 0x020e048c 0x00000030 +DATA 4 0x021b0800 0xa1390003 +DATA 4 0x021b080c 0x001F001F +DATA 4 0x021b0810 0x001F001F +DATA 4 0x021b480c 0x001F001F +DATA 4 0x021b4810 0x001F001F +DATA 4 0x021b083c 0x4220021F +DATA 4 0x021b0840 0x0207017E +DATA 4 0x021b483c 0x4201020C +DATA 4 0x021b4840 0x01660172 +DATA 4 0x021b0848 0x4A4D4E4D +DATA 4 0x021b4848 0x4A4F5049 +DATA 4 0x021b0850 0x3F3C3D31 +DATA 4 0x021b4850 0x3238372B +DATA 4 0x021b081c 0x33333333 +DATA 4 0x021b0820 0x33333333 +DATA 4 0x021b0824 0x33333333 +DATA 4 0x021b0828 0x33333333 +DATA 4 0x021b481c 0x33333333 +DATA 4 0x021b4820 0x33333333 +DATA 4 0x021b4824 0x33333333 +DATA 4 0x021b4828 0x33333333 +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b48b8 0x00000800 +DATA 4 0x021b0004 0x0002002D +DATA 4 0x021b0008 0x00333030 +DATA 4 0x021b000c 0x3F435313 +DATA 4 0x021b0010 0xB66E8B63 +DATA 4 0x021b0014 0x01FF00DB +DATA 4 0x021b0018 0x00001740 +DATA 4 0x021b001c 0x00008000 +DATA 4 0x021b002c 0x000026d2 +DATA 4 0x021b0030 0x00431023 +DATA 4 0x021b0040 0x00000027 +DATA 4 0x021b0000 0x831A0000 +DATA 4 0x021b001c 0x04008032 +DATA 4 0x021b001c 0x00008033 +DATA 4 0x021b001c 0x00048031 +DATA 4 0x021b001c 0x05208030 +DATA 4 0x021b001c 0x04008040 +DATA 4 0x021b0020 0x00005800 +DATA 4 0x021b0818 0x00011117 +DATA 4 0x021b4818 0x00011117 +DATA 4 0x021b0004 0x0002556D +DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b001c 0x00000000 + +/* set the default clock gate to save power */ +DATA 4 0x020c4068 0x00C03F3F +DATA 4 0x020c406c 0x0030FC03 +DATA 4 0x020c4070 0x0FFFC000 +DATA 4 0x020c4074 0x3FF00000 +DATA 4 0x020c4078 0x00FFF300 +DATA 4 0x020c407c 0x0F0000C3 +DATA 4 0x020c4080 0x000003FF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4 0x020e0010 0xF00000CF +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ +DATA 4 0x020e0018 0x007F007F +DATA 4 0x020e001c 0x007F007F
configs/mx6dlsabresd_defconfig +1 -1
@@ -1,3 +1,3 @@ -CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DEFAULT_FDT_FILE=\"imx6dl-sabresd.dtb\",DDR_MB=1024" +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sabresd/mx6dl_4x_mt41j128.cfg,MX6DL,DEFAULT_FDT_FILE=\"imx6dl-sabresd.dtb\",DDR_MB=1024" CONFIG_ARM=y CONFIG_TARGET_MX6SABRESD=y
Signature · 1 line
1.7.4.1
Fabio Estevam
reviewerPATCH 3/5 iMX6DL:SABRESD: Add new DDR script
Hi Ye Li,
Quoted 4 lines · Ye.Li
Add specified mx6dl_4x_mt41j128.cfg DDR script for iMX6DLSABRESD board. Not share from nitrogen6x. The default boot device also changes to SD card.
Signed-off-by Ye.Li <[email protected]>
Thanks for the patch, but I have already sent this one:
https://patchwork.ozlabs.org/patch/381961/
Regards,
Fabio Estevam
PATCH 3/5 iMX6DL:SABRESD: Add new DDR script
Quoted 6 lines · Fabio Estevam
Hi Ye Li,
Quoted 3 lines · Ye.Li
Add specified mx6dl_4x_mt41j128.cfg DDR script for iMX6DLSABRESD board. Not share from nitrogen6x. The default boot device also changes to SD card.
Quoted 7 lines
Quoted 1 line
Signed-off-by Ye.Li <[email protected]>Thanks for the patch, but I have already sent this one:
https://patchwork.ozlabs.org/patch/381961/Regards,
Fabio Estevam
I did not notice your patch. Thanks for submit it. I will rework mine.
Best regards,
Ye Li
PATCH 4/5 iMX6Solo:SABRESD: Add the i.MX6Solo SABRESD board support
In reply to Ye.LiThe i.MX6solo SABRE-SD board configuration has the following difference with i.MX6dl sabre-sd:
- DDR bus width: 32bit
- DDR capacity: 512M
--- board/freescale/mx6sabresd/mx6solo_4x_mt41j128.cfg | 106 ++++++++++++++++++++ configs/mx6solosabresd_defconfig | 3 + include/configs/mx6sabre_common.h | 14 ++- 3 files changed, 121 insertions(+), 2 deletions(-) create mode 100644 board/freescale/mx6sabresd/mx6solo_4x_mt41j128.cfg create mode 100644 configs/mx6solosabresd_defconfig
board/freescale/mx6sabresd/mx6solo_4x_mt41j128.cfg new file +106 -0
@@ -0,0 +1,106 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * Jason Liu <[email protected]> + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer doc/README.imximage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ + +/* image version */ +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +DATA 4 0x020e0774 0x000C0000 +DATA 4 0x020e0754 0x00000000 +DATA 4 0x020e04ac 0x00000030 +DATA 4 0x020e04b0 0x00000030 +DATA 4 0x020e0464 0x00000030 +DATA 4 0x020e0490 0x00000030 +DATA 4 0x020e074c 0x00000030 +DATA 4 0x020e0494 0x00000030 +DATA 4 0x020e04a0 0x00000000 +DATA 4 0x020e04b4 0x00000030 +DATA 4 0x020e04b8 0x00000030 +DATA 4 0x020e076c 0x00000030 +DATA 4 0x020e0750 0x00020000 +DATA 4 0x020e04bc 0x00000030 +DATA 4 0x020e04c0 0x00000030 +DATA 4 0x020e04c4 0x00000030 +DATA 4 0x020e04c8 0x00000030 +DATA 4 0x020e0760 0x00020000 +DATA 4 0x020e0764 0x00000030 +DATA 4 0x020e0770 0x00000030 +DATA 4 0x020e0778 0x00000030 +DATA 4 0x020e077c 0x00000030 +DATA 4 0x020e0470 0x00000030 +DATA 4 0x020e0474 0x00000030 +DATA 4 0x020e0478 0x00000030 +DATA 4 0x020e047c 0x00000030 +DATA 4 0x021b0800 0xa1390003 +DATA 4 0x021b080c 0x001F001F +DATA 4 0x021b0810 0x001F001F +DATA 4 0x021b083c 0x42190219 +DATA 4 0x021b0840 0x017B0177 +DATA 4 0x021b0848 0x4B4D4E4D +DATA 4 0x021b0850 0x3F3E2D36 +DATA 4 0x021b081c 0x33333333 +DATA 4 0x021b0820 0x33333333 +DATA 4 0x021b0824 0x33333333 +DATA 4 0x021b0828 0x33333333 +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b0004 0x0002002D +DATA 4 0x021b0008 0x00333030 +DATA 4 0x021b000c 0x3F435313 +DATA 4 0x021b0010 0xB66E8B63 +DATA 4 0x021b0014 0x01FF00DB +DATA 4 0x021b0018 0x00001740 +DATA 4 0x021b001c 0x00008000 +DATA 4 0x021b002c 0x000026d2 +DATA 4 0x021b0030 0x00431023 +DATA 4 0x021b0040 0x00000017 +DATA 4 0x021b0000 0x83190000 +DATA 4 0x021b001c 0x04008032 +DATA 4 0x021b001c 0x00008033 +DATA 4 0x021b001c 0x00048031 +DATA 4 0x021b001c 0x05208030 +DATA 4 0x021b001c 0x04008040 +DATA 4 0x021b0020 0x00005800 +DATA 4 0x021b0818 0x00011117 +DATA 4 0x021b0004 0x0002556D +DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b001c 0x00000000 + +/* set the default clock gate to save power */ +DATA 4 0x020c4068 0x00C03F3F +DATA 4 0x020c406c 0x0030FC03 +DATA 4 0x020c4070 0x0FFFC000 +DATA 4 0x020c4074 0x3FF00000 +DATA 4 0x020c4078 0x00FFF300 +DATA 4 0x020c407c 0x0F0000C3 +DATA 4 0x020c4080 0x000003FF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4 0x020e0010 0xF00000CF +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ +DATA 4 0x020e0018 0x007F007F +DATA 4 0x020e001c 0x007F007F
configs/mx6solosabresd_defconfig new file +3 -0
@@ -0,0 +1,3 @@ +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sabresd/mx6solo_4x_mt41j128.cfg,MX6S,DEFAULT_FDT_FILE=\"imx6dl-sabresd.dtb\",DDR_MB=512" +CONFIG_ARM=y +CONFIG_TARGET_MX6SABRESD=y
include/configs/mx6sabre_common.h +12 -2
@@ -11,6 +11,11 @@#define CONFIG_MX6 +#ifdef CONFIG_MX6S +#define CONFIG_MX6DL +#define CONFIG_SYS_NOSMP "nosmp" +#endif +#include "mx6_common.h" #include <linux/sizes.h>
@@ -97,6 +102,10 @@#define CONFIG_LOADADDR 0x12000000#define CONFIG_SYS_TEXT_BASE 0x17800000 +#ifndef CONFIG_SYS_NOSMP +#define CONFIG_SYS_NOSMP +#endif +#ifdef CONFIG_SUPPORT_EMMC_BOOT #define EMMC_ENV \ "emmcdev=2\0" \
@@ -146,7 +155,8 @@"fi; " \"fi\0" \EMMC_ENV \ -"mmcargs=setenv bootargs console=${console},${baudrate} " \ +"smp=" CONFIG_SYS_NOSMP "\0" \ +"mmcargs=setenv bootargs console=${console},${baudrate} ${smp} " \"root=${mmcroot}\0" \"loadbootscript=" \"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
@@ -169,7 +179,7 @@"else " \"bootz; " \"fi;\0" \ -"netargs=setenv bootargs console=${console},${baudrate} " \ +"netargs=setenv bootargs console=${console},${baudrate} ${smp} " \"root=/dev/nfs " \"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \"netboot=echo Booting from net ...; " \
Signature · 1 line
1.7.4.1
Fabio Estevam
reviewerPATCH 4/5 iMX6Solo:SABRESD: Add the i.MX6Solo SABRESD board support
include/configs/mx6sabre_common.h line 158
Quoted 9 lines · Ye.Li
#ifdef
CONFIG_SUPPORT_EMMC_BOOT#define EMMC_ENV \ "emmcdev=2\0" \include/configs/mx6sabre_common.h +1
-1@@ -146,7 +155,8 @@"fi; " \"fi\0" \EMMC_ENV \ -"mmcargs=setenv bootargs console=${console},${baudrate} " \ +"smp=" CONFIG_SYS_NOSMP "\0" \
Why do we need this 'smp' string?
PATCH 4/5 iMX6Solo:SABRESD: Add the i.MX6Solo SABRESD board support
Quoted 12 lines · Fabio Estevam
include/configs/mx6sabre_common.h line 158
Quoted 9 lines · Ye.Li
#ifdef
CONFIG_SUPPORT_EMMC_BOOT#define EMMC_ENV \ "emmcdev=2\0" \include/configs/mx6sabre_common.h +1
-1@@ -146,7 +155,8 @@"fi; " \"fi\0" \EMMC_ENV \ -"mmcargs=setenv bootargs console=${console},${baudrate} " \ +"smp=" CONFIG_SYS_NOSMP "\0" \Why do we need this 'smp' string?
This "nosmp" is intended for imx6solo on a SMP kernel, which asks SMP kernel to act as UP kernel. If kernel supports to detect the uni-processor or multi-processor with cores number from SCU, this parameter is not necessary . But it is nice to have. How do you think?
Best regards,
Ye Li
PATCH 4/5 iMX6Solo:SABRESD: Add the i.MX6Solo SABRESD board support
Quoted 14 lines · On Wed, Sep 3, 2014 at 4:23 AM, Li Ye-B37916 <[email protected]> wrote:
Quoted 12 lines · Fabio Estevam
include/configs/mx6sabre_common.h line 158
Quoted 9 lines · Ye.Li
#ifdef
CONFIG_SUPPORT_EMMC_BOOT#define EMMC_ENV \ "emmcdev=2\0" \include/configs/mx6sabre_common.h +1
-1@@ -146,7 +155,8 @@"fi; " \"fi\0" \EMMC_ENV \ -"mmcargs=setenv bootargs console=${console},${baudrate} " \ +"smp=" CONFIG_SYS_NOSMP "\0" \Why do we need this 'smp' string?
Quoted 1 line
This "nosmp" is intended for imx6solo on a SMP kernel, which asks SMP kernel to act as UP kernel. If kernel supports to detect the uni-processor or multi-processor with cores number from SCU, this parameter is not necessary . But it is nice to have. How do you think?
is this a real mx6solo processor on this board, or is it a dual-lite that you only wants to use a single core to 'simulate' a solo?
Signature · 3 lines
Otavio Salvador O.S. Systems http://www.ossystems.com.br http://code.ossystems.com.br Mobile: +55 (53) 9981-7854 Mobile: +1 (347) 903-9750
PATCH 4/5 iMX6Solo:SABRESD: Add the i.MX6Solo SABRESD board support
Quoted 14 lines · Otavio Salvador
Quoted 13 lines · On Wed, Sep 3, 2014 at 4:23 AM, Li Ye-B37916 <[email protected]> wrote:
Quoted 12 lines · Fabio Estevam
include/configs/mx6sabre_common.h line 158
Quoted 9 lines · Ye.Li
#ifdef
CONFIG_SUPPORT_EMMC_BOOT#define EMMC_ENV \ "emmcdev=2\0" \include/configs/mx6sabre_common.h +1
-1@@ -146,7 +155,8 @@"fi; " \"fi\0" \EMMC_ENV \ -"mmcargs=setenv bootargs console=${console},${baudrate} " \ +"smp=" CONFIG_SYS_NOSMP "\0" \Why do we need this 'smp' string?
Quoted 4 lines
Quoted 1 line
This "nosmp" is intended for imx6solo on a SMP kernel, which asks SMP kernel to act as UP kernel. If kernel supports to detect the uni-processor or multi-processor with cores number from SCU, this parameter is not necessary . But it is nice to have. How do you think?
is this a real mx6solo processor on this board, or is it a dual-lite that you only wants to use a single core to 'simulate' a solo?
This is a real mx6solo processor on this board.
Your question reminders me this bootarg is indeed for simulation. In fsl release, we provide a feature to simulate the mx6dl for mx6solo. But on a real mx6solo board, this bootarg is unnecessary.
Best regards,
Ye Li
Fabio Estevam
reviewerPATCH 4/5 iMX6Solo:SABRESD: Add the i.MX6Solo SABRESD board support
Hi Ye,
Quoted 3 lines · On Tue, Sep 9, 2014 at 12:35 AM, Li Ye-B37916 <[email protected]> wrote:
This is a real mx6solo processor on this board.
Your question reminders me this bootarg is indeed for simulation. In fsl release, we provide a feature to simulate the mx6dl for mx6solo. But on a real mx6solo board, this bootarg is unnecessary.
In this case, let's skip the 'smp' then.
Thanks
PATCH 4/5 iMX6Solo:SABRESD: Add the i.MX6Solo SABRESD board support
Hi Fabio,
Quoted 8 lines · Fabio Estevam
Hi Ye,
Quoted 2 lines · On Tue, Sep 9, 2014 at 12:35 AM, Li Ye-B37916 <[email protected]> wrote:
This is a real mx6solo processor on this board.
Your question reminders me this bootarg is indeed for simulation. In fsl release, we provide a feature to simulate the mx6dl for mx6solo. But on a real mx6solo board, this bootarg is unnecessary.In this case, let's skip the 'smp' then.
Thanks
Agree. Have removed the "smp" string in v2 patch.
Best regards,
Ye Li
PATCH 5/5 iMX6Solo:SABREAUTO: Add the i.MX6Solo SABREAUTO board support
In reply to Ye.LiThis patch is to add the i.MX6solo sabreauto support,
The i.MX6solo sabreauto board configuration has the following difference with i.MX6dl sabreauto:
- DDR bus width: 32bit
- DDR capacity: 1024M
--- board/freescale/mx6qsabreauto/mx6solo.cfg | 106 +++++++++++++++++++++++++++++ configs/mx6solosabreauto_defconfig | 3 + 2 files changed, 109 insertions(+), 0 deletions(-) create mode 100644 board/freescale/mx6qsabreauto/mx6solo.cfg create mode 100644 configs/mx6solosabreauto_defconfig
board/freescale/mx6qsabreauto/mx6solo.cfg new file +106 -0
@@ -0,0 +1,106 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * Jason Liu <[email protected]> + * + * SPDX-License-Identifier: GPL-2.0+ + * + * Refer doc/README.imximage for more details about how-to configure + * and create imximage boot image + * + * The syntax is taken as close as possible with the kwbimage + */ +/* image version */ + +IMAGE_VERSION 2 + +/* + * Boot Device : one of + * spi, sd (the board has no nand neither onenand) + */ +BOOT_FROM sd + +/* + * Device Configuration Data (DCD) + * + * Each entry must have the format: + * Addr-type Address Value + * + * where: + * Addr-type register length (1,2 or 4 bytes) + * Address absolute address of the register + * value value to be stored in the register + */ +DATA 4 0x020e0774 0x000C0000 +DATA 4 0x020e0754 0x00000000 +DATA 4 0x020e04ac 0x00000030 +DATA 4 0x020e04b0 0x00000030 +DATA 4 0x020e0464 0x00000030 +DATA 4 0x020e0490 0x00000030 +DATA 4 0x020e074c 0x00000030 +DATA 4 0x020e0494 0x00000030 +DATA 4 0x020e04a0 0x00000000 +DATA 4 0x020e04b4 0x00000030 +DATA 4 0x020e04b8 0x00000030 +DATA 4 0x020e076c 0x00000030 +DATA 4 0x020e0750 0x00020000 +DATA 4 0x020e04bc 0x00000028 +DATA 4 0x020e04c0 0x00000028 +DATA 4 0x020e04c4 0x00000028 +DATA 4 0x020e04c8 0x00000028 +DATA 4 0x020e0760 0x00020000 +DATA 4 0x020e0764 0x00000028 +DATA 4 0x020e0770 0x00000028 +DATA 4 0x020e0778 0x00000028 +DATA 4 0x020e077c 0x00000028 +DATA 4 0x020e0470 0x00000028 +DATA 4 0x020e0474 0x00000028 +DATA 4 0x020e0478 0x00000028 +DATA 4 0x020e047c 0x00000028 +DATA 4 0x021b0800 0xa1390003 +DATA 4 0x021b080c 0x001F001F +DATA 4 0x021b0810 0x001F001F +DATA 4 0x021b083c 0x421C0216 +DATA 4 0x021b0840 0x017B017A +DATA 4 0x021b0848 0x4B4A4E4C +DATA 4 0x021b0850 0x3F3F3334 +DATA 4 0x021b081c 0x33333333 +DATA 4 0x021b0820 0x33333333 +DATA 4 0x021b0824 0x33333333 +DATA 4 0x021b0828 0x33333333 +DATA 4 0x021b08b8 0x00000800 +DATA 4 0x021b0004 0x00020025 +DATA 4 0x021b0008 0x00333030 +DATA 4 0x021b000c 0x676B5313 +DATA 4 0x021b0010 0xB66E8B63 +DATA 4 0x021b0014 0x01FF00DB +DATA 4 0x021b0018 0x00001740 +DATA 4 0x021b001c 0x00008000 +DATA 4 0x021b002c 0x000026d2 +DATA 4 0x021b0030 0x006B1023 +DATA 4 0x021b0040 0x00000027 +DATA 4 0x021b0000 0x84190000 +DATA 4 0x021b001c 0x04008032 +DATA 4 0x021b001c 0x00008033 +DATA 4 0x021b001c 0x00048031 +DATA 4 0x021b001c 0x05208030 +DATA 4 0x021b001c 0x04008040 +DATA 4 0x021b0020 0x00005800 +DATA 4 0x021b0818 0x00011117 +DATA 4 0x021b0004 0x00025565 +DATA 4 0x021b0404 0x00011006 +DATA 4 0x021b001c 0x00000000 + +/* set the default clock gate to save power */ +DATA 4 0x020c4068 0x00C03F3F +DATA 4 0x020c406c 0x0030FC03 +DATA 4 0x020c4070 0x0FFFC000 +DATA 4 0x020c4074 0x3FF00000 +DATA 4 0x020c4078 0xFFFFF300 +DATA 4 0x020c407c 0x0F0000C3 +DATA 4 0x020c4080 0x00000FFF + +/* enable AXI cache for VDOA/VPU/IPU */ +DATA 4 0x020e0010 0xF00000CF +/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ +DATA 4 0x020e0018 0x007F007F +DATA 4 0x020e001c 0x007F007F
configs/mx6solosabreauto_defconfig new file +3 -0
@@ -0,0 +1,3 @@ +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6qsabreauto/mx6solo.cfg,MX6S,DEFAULT_FDT_FILE=\"imx6dl-sabreauto.dtb\",DDR_MB=1024" +CONFIG_ARM=y +CONFIG_TARGET_MX6QSABREAUTO=y
Signature · 1 line
1.7.4.1