iommu/arm-smmu: hard iova_to_phys
cover iommu/arm-smmu: hard iova_to_phys
This series introduces support for performing iova-to-phys translations via the ARM SMMU hardware on supported implementations. We also make use of some new generic macros for polling hardware registers.
The iopoll macros were previously discussed here:
http://marc.info/?l=linux-arm-kernel&m=140414727509158
Matt Wagantall (1):
iopoll: Introduce memory-mapped IO polling macros
Mitchel Humpherys (1):
iommu/arm-smmu: add support for iova_to_phys through ATS1PR
drivers/iommu/arm-smmu.c | 73 +++++++++++++++++++++++++++++- include/linux/iopoll.h | 114 +++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 186 insertions(+), 1 deletion(-) create mode 100644 include/linux/iopoll.h
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
PATCH 1/2 iopoll: Introduce memory-mapped IO polling macros
From: Matt Wagantall <[email protected]>
It is sometimes necessary to poll a memory-mapped register until its value satisfies some condition. Introduce a family of convenience macros that do this. Tight-loop and sleeping versions are provided with and without timeouts.
--- include/linux/iopoll.h | 114 +++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 114 insertions(+) create mode 100644 include/linux/iopoll.h
include/linux/iopoll.h new file +114 -0
@@ -0,0 +1,114 @@ +/* +* Copyright (c) 2012-2014 The Linux Foundation. All rights reserved. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 and +* only version 2 as published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#ifndef _LINUX_IOPOLL_H +#define _LINUX_IOPOLL_H + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/hrtimer.h> +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/io.h> + +/** +* readl_poll_timeout - Periodically poll an address until a condition is met or a timeout occurs +* @addr: Address to poll +* @val: Variable to read the value into +* @cond: Break condition (usually involving @val) +* @sleep_us: Maximum time to sleep between reads in us (0 tight-loops) +* @timeout_us: Timeout in us, 0 means never timeout +* +* Returns 0 on success and -ETIMEDOUT upon a timeout. In either +* case, the last read value at @addr is stored in @val. Must not +* be called from atomic context if sleep_us or timeout_us are used. +*/ +#define readl_poll_timeout (addr, val, cond, sleep_us, timeout_us) \ +({ \ + ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \ + might_sleep_if(timeout_us); \ + for (;;) { \ + (val) = readl(addr); \ + if (cond) \ + break; \ + if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \ + (val) = readl(addr); \ + break; \ + } \ + if (sleep_us) \ + usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \ + } \ + (cond) ? 0 : -ETIMEDOUT; \ +}) + +/** +* readl_poll_timeout_noirq - Periodically poll an address until a condition is met or a timeout occurs +* @addr: Address to poll +* @val: Variable to read the value into +* @cond: Break condition (usually involving @val) +* @max_reads: Maximum number of reads before giving up +* @time_between_us: Time to udelay() between successive reads +* +* Returns 0 on success and -ETIMEDOUT upon a timeout. +*/ +#define readl_poll_timeout_noirq (addr, val, cond, max_reads, time_between_us) \ +({ \ + int count; \ + for (count = (max_reads); count > 0; count--) { \ + (val) = readl(addr); \ + if (cond) \ + break; \ + udelay(time_between_us); \ + } \ + (cond) ? 0 : -ETIMEDOUT; \ +}) + +/** +* readl_poll - Periodically poll an address until a condition is met +* @addr: Address to poll +* @val: Variable to read the value into +* @cond: Break condition (usually involving @val) +* @sleep_us: Maximum time to sleep between reads in us (0 tight-loops) +* +* Must not be called from atomic context if sleep_us is used. +*/ +#define readl_poll (addr, val, cond, sleep_us) \ + readl_poll_timeout(addr, val, cond, sleep_us, 0) + +/** +* readl_tight_poll_timeout - Tight-loop on an address until a condition is met or a timeout occurs +* @addr: Address to poll +* @val: Variable to read the value into +* @cond: Break condition (usually involving @val) +* @timeout_us: Timeout in us, 0 means never timeout +* +* Returns 0 on success and -ETIMEDOUT upon a timeout. In either +* case, the last read value at @addr is stored in @val. Must not +* be called from atomic context if timeout_us is used. +*/ +#define readl_tight_poll_timeout (addr, val, cond, timeout_us) \ + readl_poll_timeout(addr, val, cond, 0, timeout_us) + +/** +* readl_tight_poll - Tight-loop on an address until a condition is met +* @addr: Address to poll +* @val: Variable to read the value into +* @cond: Break condition (usually involving @val) +* +* May be called from atomic context. +*/ +#define readl_tight_poll (addr, val, cond) \ + readl_poll_timeout(addr, val, cond, 0, 0) + +#endif /* _LINUX_IOPOLL_H */
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
PATCH 1/2 iopoll: Introduce memory-mapped IO polling macros
Hi Mitch, Matt,
Quoted 6 lines · Mitchel Humpherys
From: Matt Wagantall <[email protected]>
It is sometimes necessary to poll a memory-mapped register until its value satisfies some condition. Introduce a family of convenience macros that do this. Tight-loop and sleeping versions are provided with and without timeouts.
[...]
Quoted 11 lines
include/linux/iopoll.h new file +11
-0+/** +* readl_poll_timeout_noirq - Periodically poll an address until a condition is met or a timeout occurs +* @addr: Address to poll +* @val: Variable to read the value into +* @cond: Break condition (usually involving @val) +* @max_reads: Maximum number of reads before giving up +* @time_between_us: Time to udelay() between successive reads +* +* Returns 0 on success and -ETIMEDOUT upon a timeout. +*/ +#define readl_poll_timeout_noirq (addr, val, cond, max_reads, time_between_us) \
include/linux/iopoll.h line 75
Quoted 10 lines
include/linux/iopoll.h new file +10
-0+({ \ +int count; \ +for (count = (max_reads); count >0 ; count--) { \ + (val) =readl (addr); \ +if (cond) \ +break ; \ +udelay (time_between_us); \ + } \ + (cond) ?0 : -ETIMEDOUT ; \ +})
I think I'd just name this one readl_poll_timeout_atomic, then drop the helper macros you define later on. Drivers should be able to figure out the parameters they want pretty easily and it makes it more explicit imo.
Anyway, the rest of the patch looks fine.
Will
PATCH 2/2 iommu/arm-smmu: add support for iova_to_phys through ATS1PR
In reply to Mitchel HumpherysCurrently, we provide the iommu_ops.iova_to_phys service by doing a table walk in software to translate IO virtual addresses to physical addresses. On SMMUs that support it, it can be useful to ask the SMMU itself to do the translation. This can be used to warm the TLBs for an SMMU. It can also be useful for testing and hardware validation.
Since the address translation registers are optional on SMMUv2, only enable hardware translations when using SMMUv1 or when SMMU_IDR0.S1TS=1 and SMMU_IDR0.ATOSNS=0, as described in the ARM SMMU v1-v2 spec.
--- drivers/iommu/arm-smmu.c | 73 +++++++++++++++++++++++++++++++++++++++++++++++- 1 file changed, 72 insertions(+), 1 deletion(-)
drivers/iommu/arm-smmu.c +72 -1
@@ -36,6 +36,7 @@#include <linux/interrupt.h> #include <linux/io.h> #include <linux/iommu.h> +#include <linux/iopoll.h> #include <linux/mm.h> #include <linux/module.h> #include <linux/of.h>
@@ -140,6 +141,7 @@#define ID0_S2TS (1 << 29)#define ID0_NTS (1 << 28)#define ID0_SMS (1 << 27) +#define ID0_ATOSNS (1 << 26)#define ID0_PTFS_SHIFT 24#define ID0_PTFS_MASK 0x2#define ID0_PTFS_V8_ONLY 0x2
@@ -231,11 +233,17 @@#define ARM_SMMU_CB_TTBR0_HI 0x24#define ARM_SMMU_CB_TTBCR 0x30#define ARM_SMMU_CB_S1_MAIR0 0x38 +#define ARM_SMMU_CB_PAR_LO 0x50 +#define ARM_SMMU_CB_PAR_HI 0x54#define ARM_SMMU_CB_FSR 0x58#define ARM_SMMU_CB_FAR_LO 0x60#define ARM_SMMU_CB_FAR_HI 0x64#define ARM_SMMU_CB_FSYNR0 0x68#define ARM_SMMU_CB_S1_TLBIASID 0x610 +#define ARM_SMMU_CB_ATS1PR_LO 0x800 +#define ARM_SMMU_CB_ATS1PR_HI 0x804 +#define ARM_SMMU_CB_ATSR 0x8f0 +#define ATSR_LOOP_TIMEOUT 1000000/* 1s! */ #define SCTLR_S1_ASIDPNE (1 << 12)#define SCTLR_CFCFG (1 << 7)
@@ -247,6 +255,10 @@#define SCTLR_M (1 << 0)#define SCTLR_EAE_SBOP (SCTLR_AFE | SCTLR_TRE) +#define CB_PAR_F (1 << 0) + +#define ATSR_ACTIVE (1 << 0) +#define RESUME_RETRY (0 << 0)#define RESUME_TERMINATE (1 << 0)
@@ -354,6 +366,7 @@ struct arm_smmu_device {#define ARM_SMMU_FEAT_TRANS_S1 (1 << 2)#define ARM_SMMU_FEAT_TRANS_S2 (1 << 3)#define ARM_SMMU_FEAT_TRANS_NESTED (1 << 4) +#define ARM_SMMU_FEAT_TRANS_OPS (1 << 5)u32 features;#define ARM_SMMU_OPT_SECURE_CFG_ACCESS (1 << 0)
@@ -1485,7 +1498,7 @@ static size_t arm_smmu_unmap(struct iommu_domain *domain, unsigned long iova,return ret ?0 : size; } -static phys_addr_t arm_smmu_iova_to_phys (struct iommu_domain *domain, +static phys_addr_t arm_smmu_iova_to_phys_soft (struct iommu_domain *domain,dma_addr_t iova) {pgd_t *pgdp, pgd;
@@ -1518,6 +1531,59 @@ static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain,return __pfn_to_phys (pte_pfn (pte)) | (iova & ~PAGE_MASK ); } +static phys_addr_t arm_smmu_iova_to_phys_hard (struct iommu_domain *domain, +dma_addr_t iova) +{ +struct arm_smmu_domain *smmu_domain = domain->priv; +struct arm_smmu_device *smmu = smmu_domain->smmu; +struct arm_smmu_cfg *cfg = &smmu_domain->cfg; +struct device *dev = smmu->dev; +void __iomem *cb_base; +u32 tmp; +u64 phys; + + cb_base =ARM_SMMU_CB_BASE (smmu) +ARM_SMMU_CB (smmu, cfg->cbndx); + +if (smmu->version ==1 ) { +u32 reg = iova & ~0xFFF ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_LO ); + }else { +u32 reg = iova & ~0xFFF ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_LO ); + reg = (iova & ~0xFFF ) >>32 ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_HI ); + } + +if (readl_poll_timeout (cb_base +ARM_SMMU_CB_ATSR , tmp, + !(tmp &ATSR_ACTIVE ),10 ,ATSR_LOOP_TIMEOUT )) { +dev_err (dev, +"iova to phys timed out on 0x%pa for %s. Falling back to software table walk.\n" , + &iova,dev_name (dev)); +return arm_smmu_iova_to_phys_soft (domain, iova); + } + + phys =readl_relaxed (cb_base +ARM_SMMU_CB_PAR_LO ); + phys |= ((u64 )readl_relaxed (cb_base +ARM_SMMU_CB_PAR_HI )) <<32 ; + +if (phys &CB_PAR_F ) { +dev_err (dev,"translation fault on %s!\n" ,dev_name (dev)); +dev_err (dev,"PAR = 0x%llx\n" , phys); + } + phys = (phys &0xFFFFFFF000ULL ) | (iova &0x00000FFF ); + +return phys; +} + +static phys_addr_t arm_smmu_iova_to_phys (struct iommu_domain *domain, +dma_addr_t iova) +{ +struct arm_smmu_domain *smmu_domain = domain->priv; + +if (smmu_domain->smmu->features &ARM_SMMU_FEAT_TRANS_OPS ) +return arm_smmu_iova_to_phys_hard (domain, iova); +return arm_smmu_iova_to_phys_soft (domain, iova); +} +static int arm_smmu_domain_has_cap (struct iommu_domain *domain,unsigned long cap) {
@@ -1730,6 +1796,11 @@ static int arm_smmu_device_cfg_probe(struct arm_smmu_device *smmu)return -ENODEV ; } +if (smmu->version ==1 || (!(id &ID0_ATOSNS ) && (id &ID0_S1TS ))) { + smmu->features |=ARM_SMMU_FEAT_TRANS_OPS ; +dev_notice (smmu->dev,"\taddress translation ops\n" ); + } +if (id &ID0_CTTW ) { smmu->features |=ARM_SMMU_FEAT_COHERENT_WALK ;dev_notice (smmu->dev,"\tcoherent table walk\n" );
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
PATCH 2/2 iommu/arm-smmu: add support for iova_to_phys through ATS1PR
Hi Mitch,
Quoted 9 lines · Mitchel Humpherys
Currently, we provide the iommu_ops.iova_to_phys service by doing a table walk in software to translate IO virtual addresses to physical addresses. On SMMUs that support it, it can be useful to ask the SMMU itself to do the translation. This can be used to warm the TLBs for an SMMU. It can also be useful for testing and hardware validation.
Since the address translation registers are optional on SMMUv2, only enable hardware translations when using SMMUv1 or when SMMU_IDR0.S1TS=1 and SMMU_IDR0.ATOSNS=0, as described in the ARM SMMU v1-v2 spec.
[...]
Quoted 18 lines
drivers/iommu/arm-smmu.c +18
-0+static phys_addr_t arm_smmu_iova_to_phys_hard (struct iommu_domain *domain, +dma_addr_t iova) +{ +struct arm_smmu_domain *smmu_domain = domain->priv; +struct arm_smmu_device *smmu = smmu_domain->smmu; +struct arm_smmu_cfg *cfg = &smmu_domain->cfg; +struct device *dev = smmu->dev; +void __iomem *cb_base; +u32 tmp; +u64 phys; + + cb_base =ARM_SMMU_CB_BASE (smmu) +ARM_SMMU_CB (smmu, cfg->cbndx); + +if (smmu->version ==1 ) { +u32 reg = iova & ~0xFFF ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_LO ); + }else { +u32 reg = iova & ~0xFFF ;
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1561
Quoted 10 lines
drivers/iommu/arm-smmu.c +10
-0+writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_LO ); + reg = (iova & ~0xFFF ) >>32 ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_HI ); + } + +if (readl_poll_timeout (cb_base +ARM_SMMU_CB_ATSR , tmp, + !(tmp &ATSR_ACTIVE ),10 ,ATSR_LOOP_TIMEOUT )) { +dev_err (dev, +"iova to phys timed out on 0x%pa for %s. Falling back to software table walk.\n" , + &iova,dev_name (dev));
dev_err already prints the device name.
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1572
Quoted 11 lines
drivers/iommu/arm-smmu.c +11
-0+return arm_smmu_iova_to_phys_soft (domain, iova); + } + + phys =readl_relaxed (cb_base +ARM_SMMU_CB_PAR_LO ); + phys |= ((u64 )readl_relaxed (cb_base +ARM_SMMU_CB_PAR_HI )) <<32 ; + +if (phys &CB_PAR_F ) { +dev_err (dev,"translation fault on %s!\n" ,dev_name (dev)); +dev_err (dev,"PAR = 0x%llx\n" , phys); + } + phys = (phys &0xFFFFFFF000ULL ) | (iova &0x00000FFF );
How does this work for 64k pages?
Will
PATCH 2/2 iommu/arm-smmu: add support for iova_to_phys through ATS1PR
Quoted 37 lines · Will Deacon
Hi Mitch,
Quoted 9 lines · Mitchel Humpherys
Currently, we provide the iommu_ops.iova_to_phys service by doing a table walk in software to translate IO virtual addresses to physical addresses. On SMMUs that support it, it can be useful to ask the SMMU itself to do the translation. This can be used to warm the TLBs for an SMMU. It can also be useful for testing and hardware validation.
Since the address translation registers are optional on SMMUv2, only enable hardware translations when using SMMUv1 or when SMMU_IDR0.S1TS=1 and SMMU_IDR0.ATOSNS=0, as described in the ARM SMMU v1-v2 spec.
[...]
Quoted 22 lines
drivers/iommu/arm-smmu.c +22
-0+static phys_addr_t arm_smmu_iova_to_phys_hard (struct iommu_domain *domain, +dma_addr_t iova) +{ +struct arm_smmu_domain *smmu_domain = domain->priv; +struct arm_smmu_device *smmu = smmu_domain->smmu; +struct arm_smmu_cfg *cfg = &smmu_domain->cfg; +struct device *dev = smmu->dev; +void __iomem *cb_base; +u32 tmp; +u64 phys; + + cb_base =ARM_SMMU_CB_BASE (smmu) +ARM_SMMU_CB (smmu, cfg->cbndx); + +if (smmu->version ==1 ) { +u32 reg = iova & ~0xFFF ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_LO ); + }else { +u32 reg = iova & ~0xFFF ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_LO ); + reg = (iova & ~0xFFF ) >>32 ; +writel_relaxed (reg, cb_base +ARM_SMMU_CB_ATS1PR_HI ); + }
Quoted 8 lines
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1561
Quoted 6 lines
drivers/iommu/arm-smmu.c +6
-0+ +if (readl_poll_timeout (cb_base +ARM_SMMU_CB_ATSR , tmp, + !(tmp &ATSR_ACTIVE ),10 ,ATSR_LOOP_TIMEOUT )) { +dev_err (dev, +"iova to phys timed out on 0x%pa for %s. Falling back to software table walk.\n" , + &iova,dev_name (dev));
dev_erralready prints the device name.
Ah of course. I'll remove the dev_name.
Quoted 14 lines
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1572
Quoted 12 lines
drivers/iommu/arm-smmu.c +11
-0+return arm_smmu_iova_to_phys_soft (domain, iova); + } + + phys =readl_relaxed (cb_base +ARM_SMMU_CB_PAR_LO ); + phys |= ((u64 )readl_relaxed (cb_base +ARM_SMMU_CB_PAR_HI )) <<32 ; + +if (phys &CB_PAR_F ) { +dev_err (dev,"translation fault on %s!\n" ,dev_name (dev)); +dev_err (dev,"PAR = 0x%llx\n" , phys); + } + phys = (phys &0xFFFFFFF000ULL ) | (iova &0x00000FFF );How does this work for 64k pages?
So at the moment we're always assuming that we're using v7/v8 long descriptor format, right? All I see in the spec (14.5.15 SMMU_CBn_PAR) is that bits[47:12]=>PA[47:12]... Or am I missing something completely?
As a mental note, if we add support for v7 short descriptors (which we would like to do sometime soon) then we'll have to handle the supersection case here as well.
-Mitch
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
PATCH 2/2 iommu/arm-smmu: add support for iova_to_phys through ATS1PR
Quoted 16 lines · Mitchel Humpherys
Quoted 14 lines · Will Deacon
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1572
Quoted 11 lines · Mitchel Humpherys
drivers/iommu/arm-smmu.c +11
-0+return arm_smmu_iova_to_phys_soft (domain, iova); + } + + phys =readl_relaxed (cb_base +ARM_SMMU_CB_PAR_LO ); + phys |= ((u64 )readl_relaxed (cb_base +ARM_SMMU_CB_PAR_HI )) <<32 ; + +if (phys &CB_PAR_F ) { +dev_err (dev,"translation fault on %s!\n" ,dev_name (dev)); +dev_err (dev,"PAR = 0x%llx\n" , phys); + } + phys = (phys &0xFFFFFFF000ULL ) | (iova &0x00000FFF );How does this work for 64k pages?
Quoted 3 lines
So at the moment we're always assuming that we're using v7/v8 long descriptor format, right? All I see in the spec (14.5.15
SMMU_CBn_PAR) is that bits[47:12]=>PA[47:12]... Or am I missing something completely?
I think you've got 64k pages confused with the short-descriptor format.
When we use 64k pages with long descriptors, you're masked off bits 15-12 of the iova above, so you'll have a hole in the physical address afaict.
Will
PATCH 2/2 iommu/arm-smmu: add support for iova_to_phys through ATS1PR
Quoted 17 lines · Will Deacon
Quoted 16 lines · Mitchel Humpherys
Quoted 14 lines · Will Deacon
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1572
Quoted 11 lines · Mitchel Humpherys
drivers/iommu/arm-smmu.c +11
-0+return arm_smmu_iova_to_phys_soft (domain, iova); + } + + phys =readl_relaxed (cb_base +ARM_SMMU_CB_PAR_LO ); + phys |= ((u64 )readl_relaxed (cb_base +ARM_SMMU_CB_PAR_HI )) <<32 ; + +if (phys &CB_PAR_F ) { +dev_err (dev,"translation fault on %s!\n" ,dev_name (dev)); +dev_err (dev,"PAR = 0x%llx\n" , phys); + } + phys = (phys &0xFFFFFFF000ULL ) | (iova &0x00000FFF );How does this work for 64k pages?
Quoted 8 lines
Quoted 3 lines
So at the moment we're always assuming that we're using v7/v8 long descriptor format, right? All I see in the spec (14.5.15
SMMU_CBn_PAR) is that bits[47:12]=>PA[47:12]... Or am I missing something completely?I think you've got 64k pages confused with the short-descriptor format.
When we use 64k pages with long descriptors, you're masked off bits 15-12 of the iova above, so you'll have a hole in the physical address afaict.
Even with long descriptors the spec says bits 15-12 should come from CB_PAR... It makes no mention of reinterpreting those bits depending on the programmed page granule. The only thing I can conclude from the spec is that hardware should be smart enough to do the right thing with bits 15-12 when the page granule is 64k. Although even if hardware is smart enough I guess CB_PAR[15:12] should be the same as iova[15:12] for the 64k case?
-Mitch
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
PATCH 2/2 iommu/arm-smmu: add support for iova_to_phys through ATS1PR
Quoted 27 lines · Mitchel Humpherys
Quoted 17 lines · Will Deacon
Quoted 16 lines · Mitchel Humpherys
Quoted 14 lines · Will Deacon
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1572
Quoted 11 lines · Mitchel Humpherys
drivers/iommu/arm-smmu.c +11
-0+return arm_smmu_iova_to_phys_soft (domain, iova); + } + + phys =readl_relaxed (cb_base +ARM_SMMU_CB_PAR_LO ); + phys |= ((u64 )readl_relaxed (cb_base +ARM_SMMU_CB_PAR_HI )) <<32 ; + +if (phys &CB_PAR_F ) { +dev_err (dev,"translation fault on %s!\n" ,dev_name (dev)); +dev_err (dev,"PAR = 0x%llx\n" , phys); + } + phys = (phys &0xFFFFFFF000ULL ) | (iova &0x00000FFF );How does this work for 64k pages?
Quoted 8 lines
Quoted 3 lines
So at the moment we're always assuming that we're using v7/v8 long descriptor format, right? All I see in the spec (14.5.15
SMMU_CBn_PAR) is that bits[47:12]=>PA[47:12]... Or am I missing something completely?I think you've got 64k pages confused with the short-descriptor format.
When we use 64k pages with long descriptors, you're masked off bits 15-12 of the iova above, so you'll have a hole in the physical address afaict.
Quoted 7 lines
Even with long descriptors the spec says bits 15-12 should come from
CB_PAR... It makes no mention of reinterpreting those bits depending on the programmed page granule. The only thing I can conclude from the spec is that hardware should be smart enough to do the right thing with bits 15-12 when the page granule is 64k. Although even if hardware is smart enough I guess CB_PAR[15:12] should be the same as iova[15:12] for the 64k case?
Yeah, fair enough, the code you have should work correctly then. Unfortunately, I don't have any suitable hardware on which to test it.
Will
PATCH 2/2 iommu/arm-smmu: add support for iova_to_phys through ATS1PR
Quoted 36 lines · Will Deacon
Quoted 27 lines · Mitchel Humpherys
Quoted 17 lines · Will Deacon
Quoted 16 lines · Mitchel Humpherys
Quoted 14 lines · Will Deacon
drivers/iommu/arm-smmu.c static phys_addr_t arm_smmu_iova_to_phys(struct iommu_domain *domain, · line 1572
Quoted 11 lines · Mitchel Humpherys
drivers/iommu/arm-smmu.c +11
-0+return arm_smmu_iova_to_phys_soft (domain, iova); + } + + phys =readl_relaxed (cb_base +ARM_SMMU_CB_PAR_LO ); + phys |= ((u64 )readl_relaxed (cb_base +ARM_SMMU_CB_PAR_HI )) <<32 ; + +if (phys &CB_PAR_F ) { +dev_err (dev,"translation fault on %s!\n" ,dev_name (dev)); +dev_err (dev,"PAR = 0x%llx\n" , phys); + } + phys = (phys &0xFFFFFFF000ULL ) | (iova &0x00000FFF );How does this work for 64k pages?
Quoted 8 lines
Quoted 3 lines
So at the moment we're always assuming that we're using v7/v8 long descriptor format, right? All I see in the spec (14.5.15
SMMU_CBn_PAR) is that bits[47:12]=>PA[47:12]... Or am I missing something completely?I think you've got 64k pages confused with the short-descriptor format.
When we use 64k pages with long descriptors, you're masked off bits 15-12 of the iova above, so you'll have a hole in the physical address afaict.
Quoted 7 lines
Even with long descriptors the spec says bits 15-12 should come from
CB_PAR... It makes no mention of reinterpreting those bits depending on the programmed page granule. The only thing I can conclude from the spec is that hardware should be smart enough to do the right thing with bits 15-12 when the page granule is 64k. Although even if hardware is smart enough I guess CB_PAR[15:12] should be the same as iova[15:12] for the 64k case?
Quoted 2 lines
Yeah, fair enough, the code you have should work correctly then. Unfortunately, I don't have any suitable hardware on which to test it.
FWIW, I have tested this on a few platforms here. I'll send out a v2 for the series then with the changes you suggested on the iopoll patch.
-Mitch
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
cover iommu/arm-smmu: hard iova_to_phys
In reply to Mitchel HumpherysQuoted 6 lines · Mitchel Humpherys
This series introduces support for performing iova-to-phys translations via the ARM SMMU hardware on supported implementations. We also make use of some new generic macros for polling hardware registers.
The iopoll macros were previously discussed here:
http://marc.info/?l=linux-arm-kernel&m=140414727509158
Forgot to reference the previous disussion on the iova_to_phys patch. Here it is:
http://marc.info/?m=140789123928103
Quoted 5 lines
Matt Wagantall (1):
iopoll: Introduce memory-mapped IO polling macros
Quoted 7 lines
Mitchel Humpherys (1):
iommu/arm-smmu: add support foriova_to_physthrough ATS1PRdrivers/iommu/arm-smmu.c | 73 +++++++++++++++++++++++++++++- include/linux/iopoll.h | 114 +++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 186 insertions(+), 1 deletion(-) create mode 100644 include/linux/iopoll.h
-Mitch
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation