Skip to contentSkip to conversation

ahci-platform: Bump max number of clocks to 5

PATCH In review Kumar Gala 3 participants 4 messages Sep 22, 2014 – Sep 23, 2014

Subsystems (3)
lore
Share & tools
lore

Kumar Gala

author
#0 lore raw

PATCH v5 1/2 ahci-platform: Bump max number of clocks to 5

Qualcomm IPQ806x SoCs with SATA controllers need 5 clocks to be enabled.

---
v4/v5:
* Updated to upstream changes

 drivers/ata/ahci.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/ata/ahci.h +1 -1
index 59ae0ee..90156ff 100644
@@ -53,7 +53,7 @@
 
 enum {
 	AHCI_MAX_PORTS		= 32,
-	AHCI_MAX_CLKS		= 4,
+	AHCI_MAX_CLKS		= 5,
 	AHCI_MAX_SG		= 168, /* hardware max is 64K */
 	AHCI_DMA_BOUNDARY	= 0xffffffff,
 	AHCI_MAX_CMDS		= 32,
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
author
#1 lore raw

PATCH 2/2 ata: qcom: Add device tree bindings information

Add device tree binding for Qualcomm AHCI SATA controller and specifically the sata controller on the IPQ806x family of SoCs.

We can utilize the "generic-ahci" platform driver with the addition of the sata phy to enable SATA support on Qualcomm SoCs with AHCI controllers.

---
v5:
* Moved to using "generic-ahci" binding support and assigned-clocks so we can use upstream generic ahci support w/o a special driver. Updated binding spec to reflect that.

v4:
* Added simple PM ops implementation
* Added setting of pmalive clk

v3:
* Added comment about suspend/resume not supported
* Fixup ahci_platform_init_host for upstream change to interface
* cleanup error handling of rxoob clk, moved to devm_clk_get/put

v2:
* Fixed MODULE_LICENSE to be GPL v2

 .../devicetree/bindings/ata/qcom-sata.txt          | 48 ++++++++++++++++++++++
 1 file changed, 48 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/ata/qcom-sata.txt
Documentation/devicetree/bindings/ata/qcom-sata.txt new file +48 -0
new file mode 100644
index 0000000..094de91
@@ -0,0 +1,48 @@
+* Qualcomm AHCI SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible		: compatible list, must contain "generic-ahci"
+- interrupts		: <interrupt mapping for SATA IRQ>
+- reg			: <registers mapping>
+- phys			: Must contain exactly one entry as specified
+			  in phy-bindings.txt
+- phy-names		: Must be "sata-phy"
+
+Required properties for "qcom,ipq806x-ahci" compatible:
+- clocks		: Must contain an entry for each entry in clock-names.
+- clock-names		: Shall be:
+				"slave_iface" - Fabric port AHB clock for SATA
+				"iface" - AHB clock
+				"core" - core clock
+				"rxoob" - RX out-of-band clock
+				"pmalive" - Power Module Alive clock
+- assigned-clocks	: Shall be:
+				SATA_RXOOB_CLK
+				SATA_PMALIVE_CLK
+- assigned-clock-rates	: Shall be:
+				100Mhz (100000000) for SATA_RXOOB_CLK
+				100Mhz (100000000) for SATA_PMALIVE_CLK
+
+Example:
+	sata at 29000000 {
+		compatible = "qcom,ipq806x-ahci", "generic-ahci";
+		reg = <0x29000000 0x180>;
+
+		interrupts = <0 209 0x0>;
+
+		clocks = <&gcc SFAB_SATA_S_H_CLK>,
+			 <&gcc SATA_H_CLK>,
+			 <&gcc SATA_A_CLK>,
+			 <&gcc SATA_RXOOB_CLK>,
+			 <&gcc SATA_PMALIVE_CLK>;
+		clock-names = "slave_iface", "iface", "core",
+				"rxoob", "pmalive";
+		assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
+		assigned-clock-rates = <100000000>, <100000000>;
+
+		phys = <&sata_phy>;
+		phy-names = "sata-phy";
+	};
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
Reviewed-by on v5 1/2
#2 lore raw
In reply to Kumar Gala

Hi,

Thanks, this new set looks good to me, and is:

Regards,

Hans

Quoted 24 lines · Kumar Gala

Qualcomm IPQ806x SoCs with SATA controllers need 5 clocks to be enabled.

---
v4/v5:
* Updated to upstream changes

 drivers/ata/ahci.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/ata/ahci.h +1 -1
index 59ae0ee..90156ff 100644
@@ -53,7 +53,7 @@
 
 enum {
 	AHCI_MAX_PORTS		= 32,
-	AHCI_MAX_CLKS		= 4,
+	AHCI_MAX_CLKS		= 5,
 	AHCI_MAX_SG		= 168, /* hardware max is 64K */
 	AHCI_DMA_BOUNDARY	= 0xffffffff,
 	AHCI_MAX_CMDS		= 32,