Skip to contentSkip to conversation

PCI: pciehp: Flush slot control prior to reset

PATCH In review Alex Williamson 1 participant 2 messages Nov 7, 2014 – Nov 10, 2014 PCI

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 PCI: pciehp: Flush slot control prior to reset

Since 3461a068661c we don't automatically do a pcie_wait_cmd() for as part of pcie_write_cmd(), it needs to be called explicitly or triggered by the next pcie_write_cmd(). However, when we do a secondary bus reset and we're using pcie_write_cmd() to make sure that we don't see that bus reset as a hotplug event, we really want to make sure the update is complete. Testing on an old Lenovo S20 system, which sets surprise hotplug for some slots, this failure to flush results in a link down event seen by the hotplug controller when we issue the bus reset and returns us to the undesireable behavior of removing and re-adding the device. Force a flush by adding an explicit call to pcie_wait_cmd().

---

 drivers/pci/hotplug/pciehp_hpc.c |    1 +
 1 file changed, 1 insertion(+)
drivers/pci/hotplug/pciehp_hpc.c +1 -0
index 0ebf754..e540966 100644
@@ -660,6 +660,7 @@ int pciehp_reset_slot(struct slot *slot, int probe)
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, 0);
 	if (pciehp_poll_mode)
 		del_timer_sync(&ctrl->poll_timer);
+	pcie_wait_cmd(ctrl);
 
 	pci_reset_bridge_secondary_bus(ctrl->pcie->port);
 
#1 lore raw
Quoted 25 lines · Alex Williamson

Since 3461a068661c we don't automatically do a pcie_wait_cmd() for as part of pcie_write_cmd(), it needs to be called explicitly or triggered by the next pcie_write_cmd(). However, when we do a secondary bus reset and we're using pcie_write_cmd() to make sure that we don't see that bus reset as a hotplug event, we really want to make sure the update is complete. Testing on an old Lenovo S20 system, which sets surprise hotplug for some slots, this failure to flush results in a link down event seen by the hotplug controller when we issue the bus reset and returns us to the undesireable behavior of removing and re-adding the device. Force a flush by adding an explicit call to pcie_wait_cmd().

---

 drivers/pci/hotplug/pciehp_hpc.c |    1 +
 1 file changed, 1 insertion(+)
drivers/pci/hotplug/pciehp_hpc.c +0 -0
index 0ebf754..e540966 100644

drivers/pci/hotplug/pciehp_hpc.c int pciehp_reset_slot(struct slot *slot, int probe) · line 666

Quoted 7 lines
drivers/pci/hotplug/pciehp_hpc.c +1 -0
@@ -660,6 +660,7 @@ int pciehp_reset_slot(struct slot *slot, int probe)
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, 0);
 	if (pciehp_poll_mode)
 		del_timer_sync(&ctrl->poll_timer);
+	pcie_wait_cmd(ctrl);
 
 	pci_reset_bridge_secondary_bus(ctrl->pcie->port);
 

I think we might need a similar change on the other side of the reset, calling pcie_wait_cmd() explicitly before we re-enable polling. The patch above passed about 7000 VM startup/shutdown cycles (up from zero w/o the patch), but it did eventually get a spurious hotplug. With the additional pcie_wait_cmd() I'm thinking about, I've passed 8000 cycles. TL;DR, I'm probably sending a v2 of this patch. Thanks,

Alex