staging: panel: Refactor panel initialization
cover staging: panel: Refactor panel initialization
This set of patches focuses on making current initialization process easier to understand - especially it tries to emphasize what are the priorities of the params coming from different sources (Kconfig values, device profiles and module param values set on loading). I paid attention not to change to behaviour of the code itself (at least for now), so all hacky places are kept.
Mariusz Gorski (9):
staging: panel: Set default parport module param value
staging: panel: Call init function directly
staging: panel: Remove magic numbers
staging: panel: Use a macro for checking module params state
staging: panel: Start making module params read-only
staging: panel: Make two more module params read-only
staging: panel: Refactor LCD init code
staging: panel: Remove more magic number comparison
staging: panel: Move LCD-related state into struct lcd
drivers/staging/panel/panel.c | 672 ++++++++++++++++++++++-------------------- 1 file changed, 357 insertions(+), 315 deletions(-)
Signature · 1 line
2.1.3
PATCH 1/9 staging: panel: Set default parport module param value
Set default parport module param value to DEFAULT_PARPORT so that a if-block can be avoided.
--- drivers/staging/panel/panel.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/staging/panel/panel.c +1 -4
@@ -429,7 +429,7 @@ static struct timer_list scan_timer;MODULE_DESCRIPTION ("Generic parallel port LCD/Keypad driver" ); -static int parport =-1 ; +static int parport =DEFAULT_PARPORT ;module_param (parport, int,0000 );MODULE_PARM_DESC (parport,"Parallel port index (0=lpt1, 1=lpt2, ...)" );
@@ -2231,9 +2231,6 @@ static int panel_init(void)if (lcd_type <0 ) lcd_type = lcd_enabled; -if (parport <0 ) - parport =DEFAULT_PARPORT ; -/* take care of an eventual profile */ switch (profile) {case PANEL_PROFILE_CUSTOM :
Signature · 1 line
2.1.3
Re: [PATCH 1/9] staging: panel: Set default parport module param value
Quoted 4 lines · Mariusz Gorski
Set default parport module param value to
DEFAULT_PARPORTso that a if-block can be avoided.Signed-off-by Mariusz Gorski <[email protected]>
PATCH 2/9 staging: panel: Call init function directly
In reply to Mariusz GorskiRemove useless function and let the kernel call the actual init function directly.
--- drivers/staging/panel/panel.c | 7 +------ 1 file changed, 1 insertion(+), 6 deletions(-)
drivers/staging/panel/panel.c +1 -6
@@ -2222,7 +2222,7 @@ static struct parport_driver panel_driver = { };/* init function */ -static int panel_init (void ) +static int __init panel_init_module (void ) {/* for backwards compatibility */ if (keypad_type <0 )
@@ -2334,11 +2334,6 @@ static int panel_init(void)return 0 ; } -static int __init panel_init_module (void ) -{ -return panel_init (); -} - static void __exit panel_cleanup_module(void) {unregister_reboot_notifier (&panel_notifier);
Signature · 1 line
2.1.3
Re: [PATCH 2/9] staging: panel: Call init function directly
Quoted 4 lines · Mariusz Gorski
Remove useless function and let the kernel call the actual init function directly.
Signed-off-by Mariusz Gorski <[email protected]>
PATCH 3/9 staging: panel: Remove magic numbers
In reply to Mariusz GorskiGet rid of magic numbers indicating that the value of a module param is not set. Use a defined value instead.
--- drivers/staging/panel/panel.c | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-)
drivers/staging/panel/panel.c +12 -10
@@ -133,6 +133,8 @@#define LCD_ESCAPE_LEN 24/* max chars for LCD escape command */ #define LCD_ESCAPE_CHAR 27/* use char 27 for escape command */ +#define NOT_SET -1 +/* macros to simplify use of the parallel port */ #define r_ctr (x) (parport_read_control((x)->port))#define r_dtr (x) (parport_read_data((x)->port))
@@ -439,37 +441,37 @@ MODULE_PARM_DESC(profile,"1=16x2 old kp; 2=serial 16x2, new kp; 3=16x2 hantronix; " "4=16x2 nexcom; default=40x2, old kp"); -static int keypad_type =-1 ; +static int keypad_type =NOT_SET ;module_param (keypad_type, int,0000 );MODULE_PARM_DESC (keypad_type,"Keypad type: 0=none, 1=old 6 keys, 2=new 6+1 keys, 3=nexcom 4 keys" ); -static int lcd_type =-1 ; +static int lcd_type =NOT_SET ;module_param (lcd_type, int,0000 );MODULE_PARM_DESC (lcd_type,"LCD type: 0=none, 1=old //, 2=serial ks0074, 3=hantronix //, 4=nexcom //, 5=compiled-in" ); -static int lcd_height =-1 ; +static int lcd_height =NOT_SET ;module_param (lcd_height, int,0000 );MODULE_PARM_DESC (lcd_height,"Number of lines on the LCD" ); -static int lcd_width =-1 ; +static int lcd_width =NOT_SET ;module_param (lcd_width, int,0000 );MODULE_PARM_DESC (lcd_width,"Number of columns on the LCD" ); -static int lcd_bwidth =-1 ;/* internal buffer width (usually 40) */ +static int lcd_bwidth =NOT_SET ;/* internal buffer width (usually 40) */ module_param (lcd_bwidth, int,0000 );MODULE_PARM_DESC (lcd_bwidth,"Internal LCD line width (40)" ); -static int lcd_hwidth =-1 ;/* hardware buffer width (usually 64) */ +static int lcd_hwidth =NOT_SET ;/* hardware buffer width (usually 64) */ module_param (lcd_hwidth, int,0000 );MODULE_PARM_DESC (lcd_hwidth,"LCD line hardware address (64)" ); -static int lcd_charset =-1 ; +static int lcd_charset =NOT_SET ;module_param (lcd_charset, int,0000 );MODULE_PARM_DESC (lcd_charset,"LCD character set: 0=standard, 1=KS0074" ); -static int lcd_proto =-1 ; +static int lcd_proto =NOT_SET ;module_param (lcd_proto, int,0000 );MODULE_PARM_DESC (lcd_proto,"LCD communication: 0=parallel (//), 1=serial, 2=TI LCD Interface" );
@@ -515,11 +517,11 @@ MODULE_PARM_DESC(lcd_bl_pin,/* Deprecated module parameters - consider not using them anymore */ -static int lcd_enabled =-1 ; +static int lcd_enabled =NOT_SET ;module_param (lcd_enabled, int,0000 );MODULE_PARM_DESC (lcd_enabled,"Deprecated option, use lcd_type instead" ); -static int keypad_enabled =-1 ; +static int keypad_enabled =NOT_SET ;module_param (keypad_enabled, int,0000 );MODULE_PARM_DESC (keypad_enabled,"Deprecated option, use keypad_type instead" );
Signature · 1 line
2.1.3
Re: [PATCH 3/9] staging: panel: Remove magic numbers
Quoted 4 lines · Mariusz Gorski
Get rid of magic numbers indicating that the value of a module param is not set. Use a defined value instead.
Signed-off-by Mariusz Gorski <[email protected]>
PATCH 4/9 staging: panel: Use a macro for checking module params state
In reply to Mariusz GorskiAvoid values comparison and use a macro instead that checks whether module param has been set by the user to some value at loading time.
--- drivers/staging/panel/panel.c | 88 ++++++++++++++++++++++--------------------- 1 file changed, 45 insertions(+), 43 deletions(-)
drivers/staging/panel/panel.c +45 -43
@@ -135,6 +135,8 @@#define NOT_SET -1 +#define IS_NOT_SET (x) (x == NOT_SET) +/* macros to simplify use of the parallel port */ #define r_ctr (x) (parport_read_control((x)->port))#define r_dtr (x) (parport_read_data((x)->port))
@@ -1411,29 +1413,29 @@ static void lcd_init(void)switch (lcd_type) {case LCD_TYPE_OLD :/* parallel mode, 8 bits */ -if (lcd_proto <0 ) +if (IS_NOT_SET (lcd_proto)) lcd_proto =LCD_PROTO_PARALLEL ; -if (lcd_charset <0 ) +if (IS_NOT_SET (lcd_charset)) lcd_charset =LCD_CHARSET_NORMAL ;if (lcd_e_pin ==PIN_NOT_SET ) lcd_e_pin =PIN_STROBE ;if (lcd_rs_pin ==PIN_NOT_SET ) lcd_rs_pin =PIN_AUTOLF ; -if (lcd_width <0 ) +if (IS_NOT_SET (lcd_width)) lcd_width =40 ; -if (lcd_bwidth <0 ) +if (IS_NOT_SET (lcd_bwidth)) lcd_bwidth =40 ; -if (lcd_hwidth <0 ) +if (IS_NOT_SET (lcd_hwidth)) lcd_hwidth =64 ; -if (lcd_height <0 ) +if (IS_NOT_SET (lcd_height)) lcd_height =2 ;break ;case LCD_TYPE_KS0074 :/* serial mode, ks0074 */ -if (lcd_proto <0 ) +if (IS_NOT_SET (lcd_proto)) lcd_proto =LCD_PROTO_SERIAL ; -if (lcd_charset <0 ) +if (IS_NOT_SET (lcd_charset)) lcd_charset =LCD_CHARSET_KS0074 ;if (lcd_bl_pin ==PIN_NOT_SET ) lcd_bl_pin =PIN_AUTOLF ;
@@ -1442,20 +1444,20 @@ static void lcd_init(void)if (lcd_da_pin ==PIN_NOT_SET ) lcd_da_pin =PIN_D0 ; -if (lcd_width <0 ) +if (IS_NOT_SET (lcd_width)) lcd_width =16 ; -if (lcd_bwidth <0 ) +if (IS_NOT_SET (lcd_bwidth)) lcd_bwidth =40 ; -if (lcd_hwidth <0 ) +if (IS_NOT_SET (lcd_hwidth)) lcd_hwidth =16 ; -if (lcd_height <0 ) +if (IS_NOT_SET (lcd_height)) lcd_height =2 ;break ;case LCD_TYPE_NEXCOM :/* parallel mode, 8 bits, generic */ -if (lcd_proto <0 ) +if (IS_NOT_SET (lcd_proto)) lcd_proto =LCD_PROTO_PARALLEL ; -if (lcd_charset <0 ) +if (IS_NOT_SET (lcd_charset)) lcd_charset =LCD_CHARSET_NORMAL ;if (lcd_e_pin ==PIN_NOT_SET ) lcd_e_pin =PIN_AUTOLF ;
@@ -1464,42 +1466,42 @@ static void lcd_init(void)if (lcd_rw_pin ==PIN_NOT_SET ) lcd_rw_pin =PIN_INITP ; -if (lcd_width <0 ) +if (IS_NOT_SET (lcd_width)) lcd_width =16 ; -if (lcd_bwidth <0 ) +if (IS_NOT_SET (lcd_bwidth)) lcd_bwidth =40 ; -if (lcd_hwidth <0 ) +if (IS_NOT_SET (lcd_hwidth)) lcd_hwidth =64 ; -if (lcd_height <0 ) +if (IS_NOT_SET (lcd_height)) lcd_height =2 ;break ;case LCD_TYPE_CUSTOM :/* customer-defined */ -if (lcd_proto <0 ) +if (IS_NOT_SET (lcd_proto)) lcd_proto =DEFAULT_LCD_PROTO ; -if (lcd_charset <0 ) +if (IS_NOT_SET (lcd_charset)) lcd_charset =DEFAULT_LCD_CHARSET ;/* default geometry will be set later */ break ;case LCD_TYPE_HANTRONIX :/* parallel mode, 8 bits, hantronix-like */ default : -if (lcd_proto <0 ) +if (IS_NOT_SET (lcd_proto)) lcd_proto =LCD_PROTO_PARALLEL ; -if (lcd_charset <0 ) +if (IS_NOT_SET (lcd_charset)) lcd_charset =LCD_CHARSET_NORMAL ;if (lcd_e_pin ==PIN_NOT_SET ) lcd_e_pin =PIN_STROBE ;if (lcd_rs_pin ==PIN_NOT_SET ) lcd_rs_pin =PIN_SELECP ; -if (lcd_width <0 ) +if (IS_NOT_SET (lcd_width)) lcd_width =16 ; -if (lcd_bwidth <0 ) +if (IS_NOT_SET (lcd_bwidth)) lcd_bwidth =40 ; -if (lcd_hwidth <0 ) +if (IS_NOT_SET (lcd_hwidth)) lcd_hwidth =64 ; -if (lcd_height <0 ) +if (IS_NOT_SET (lcd_height)) lcd_height =2 ;break ; }
@@ -1557,7 +1559,7 @@ static void lcd_init(void)if (lcd_da_pin ==PIN_NOT_SET ) lcd_da_pin =PIN_NONE ; -if (lcd_charset <0 ) +if (IS_NOT_SET (lcd_charset)) lcd_charset =DEFAULT_LCD_CHARSET ;if (lcd_charset ==LCD_CHARSET_KS0074 )
@@ -2227,58 +2229,58 @@ static struct parport_driver panel_driver = {static int __init panel_init_module (void ) {/* for backwards compatibility */ -if (keypad_type <0 ) +if (IS_NOT_SET (keypad_type)) keypad_type = keypad_enabled; -if (lcd_type <0 ) +if (IS_NOT_SET (lcd_type)) lcd_type = lcd_enabled;/* take care of an eventual profile */ switch (profile) {case PANEL_PROFILE_CUSTOM :/* custom profile */ -if (keypad_type <0 ) +if (IS_NOT_SET (keypad_type)) keypad_type =DEFAULT_KEYPAD_TYPE ; -if (lcd_type <0 ) +if (IS_NOT_SET (lcd_type)) lcd_type =DEFAULT_LCD_TYPE ;break ;case PANEL_PROFILE_OLD :/* 8 bits, 2*16, old keypad */ -if (keypad_type <0 ) +if (IS_NOT_SET (keypad_type)) keypad_type =KEYPAD_TYPE_OLD ; -if (lcd_type <0 ) +if (IS_NOT_SET (lcd_type)) lcd_type =LCD_TYPE_OLD ; -if (lcd_width <0 ) +if (IS_NOT_SET (lcd_width)) lcd_width =16 ; -if (lcd_hwidth <0 ) +if (IS_NOT_SET (lcd_hwidth)) lcd_hwidth =16 ;break ;case PANEL_PROFILE_NEW :/* serial, 2*16, new keypad */ -if (keypad_type <0 ) +if (IS_NOT_SET (keypad_type)) keypad_type =KEYPAD_TYPE_NEW ; -if (lcd_type <0 ) +if (IS_NOT_SET (lcd_type)) lcd_type =LCD_TYPE_KS0074 ;break ;case PANEL_PROFILE_HANTRONIX :/* 8 bits, 2*16 hantronix-like, no keypad */ -if (keypad_type <0 ) +if (IS_NOT_SET (keypad_type)) keypad_type =KEYPAD_TYPE_NONE ; -if (lcd_type <0 ) +if (IS_NOT_SET (lcd_type)) lcd_type =LCD_TYPE_HANTRONIX ;break ;case PANEL_PROFILE_NEXCOM :/* generic 8 bits, 2*16, nexcom keypad, eg. Nexcom. */ -if (keypad_type <0 ) +if (IS_NOT_SET (keypad_type)) keypad_type =KEYPAD_TYPE_NEXCOM ; -if (lcd_type <0 ) +if (IS_NOT_SET (lcd_type)) lcd_type =LCD_TYPE_NEXCOM ;break ;case PANEL_PROFILE_LARGE :/* 8 bits, 2*40, old keypad */ -if (keypad_type <0 ) +if (IS_NOT_SET (keypad_type)) keypad_type =KEYPAD_TYPE_OLD ; -if (lcd_type <0 ) +if (IS_NOT_SET (lcd_type)) lcd_type =LCD_TYPE_OLD ;break ; }
Signature · 1 line
2.1.3
Re: [PATCH 4/9] staging: panel: Use a macro for checking module params state
Quoted 30 lines · Mariusz Gorski
Avoid values comparison and use a macro instead that checks whether module param has been set by the user to some value at loading time.
Signed-off-by Mariusz Gorski <[email protected]>--- drivers/staging/panel/panel.c | 88 ++++++++++++++++++++++--------------------- 1 file changed, 45 insertions(+), 43 deletions(-)drivers/staging/panel/panel.c +3
-2@@ -135,6 +135,8 @@#define NOT_SET -1 +#define IS_NOT_SET (x) (x == NOT_SET) +/* macros to simplify use of the parallel port */ #define r_ctr (x) (parport_read_control((x)->port))#define r_dtr (x) (parport_read_data((x)->port))@@ -1411,29 +1413,29 @@ static void lcd_init(void)switch (lcd_type) {case LCD_TYPE_OLD :/* parallel mode, 8 bits */ -if (lcd_proto <0 ) +if (IS_NOT_SET (lcd_proto)) lcd_proto =LCD_PROTO_PARALLEL ; -if (lcd_charset <0 )
drivers/staging/panel/panel.c static void lcd_init(void) · line 1426
Quoted 10 lines
drivers/staging/panel/panel.c +2
-1+if (IS_NOT_SET (lcd_charset)) lcd_charset =LCD_CHARSET_NORMAL ;if (lcd_e_pin ==PIN_NOT_SET ) lcd_e_pin =PIN_STROBE ;if (lcd_rs_pin ==PIN_NOT_SET ) lcd_rs_pin =PIN_AUTOLF ; -if (lcd_width <0 ) +if (IS_NOT_SET (lcd_width)) lcd_width =40 ;
(...)
I'm not convinced at all by the increased readability of this one. To me it adds obfuscation since I have to look for the macro definition to see how it checks whether the type is set or not.
I think you'd rather simply open-code the macro here and keep the natural comparison. The fields were already initialized to the NOT_SET value, better check agaist the same value here especially since it matches other tests as well. That would give :
- if (lcd_proto < 0)
+ if (lcd_proto == NOT_SET)
lcd_proto = LCD_PROTO_PARALLEL;
etc... To me it's more readable.
Willy
Re: [PATCH 4/9] staging: panel: Use a macro for checking module params state
Quoted 56 lines · Willy Tarreau
Quoted 30 lines · Mariusz Gorski
Avoid values comparison and use a macro instead that checks whether module param has been set by the user to some value at loading time.
Signed-off-by Mariusz Gorski <[email protected]>--- drivers/staging/panel/panel.c | 88 ++++++++++++++++++++++--------------------- 1 file changed, 45 insertions(+), 43 deletions(-)drivers/staging/panel/panel.c +3
-2@@ -135,6 +135,8 @@#define NOT_SET -1 +#define IS_NOT_SET (x) (x == NOT_SET) +/* macros to simplify use of the parallel port */ #define r_ctr (x) (parport_read_control((x)->port))#define r_dtr (x) (parport_read_data((x)->port))@@ -1411,29 +1413,29 @@ static void lcd_init(void)switch (lcd_type) {case LCD_TYPE_OLD :/* parallel mode, 8 bits */ -if (lcd_proto <0 ) +if (IS_NOT_SET (lcd_proto)) lcd_proto =LCD_PROTO_PARALLEL ; -if (lcd_charset <0 )drivers/staging/panel/panel.c static void lcd_init(void) · line 1426
Quoted 10 lines
drivers/staging/panel/panel.c +2
-1+if (IS_NOT_SET (lcd_charset)) lcd_charset =LCD_CHARSET_NORMAL ;if (lcd_e_pin ==PIN_NOT_SET ) lcd_e_pin =PIN_STROBE ;if (lcd_rs_pin ==PIN_NOT_SET ) lcd_rs_pin =PIN_AUTOLF ; -if (lcd_width <0 ) +if (IS_NOT_SET (lcd_width)) lcd_width =40 ;(...)
I'm not convinced at all by the increased readability of this one. To me it adds obfuscation since I have to look for the macro definition to see how it checks whether the type is set or not.
I think you'd rather simply open-code the macro here and keep the natural comparison. The fields were already initialized to the
NOT_SETvalue, better check agaist the same value here especially since it matches other tests as well. That would give :drivers/staging/panel/panel.c +1
-1-if (lcd_proto <0 ) +if (lcd_proto ==NOT_SET ) lcd_proto =LCD_PROTO_PARALLEL ;
Quoted 4 lines
etc... To me it's more readable.
Willy
Hmm ok maybe you're right, maybe I've tried to hide too much here. "x == NOT_SET" hides already enough ;) I'll fix that.
Thanks,
Mariusz
PATCH 5/9 staging: panel: Start making module params read-only
In reply to Mariusz GorskiStart decoupling module params from the actual device state, both for lcd and keypad, by keeping the params read-only and moving the device state to related structs.
--- drivers/staging/panel/panel.c | 35 +++++++++++++++++++++-------------- 1 file changed, 21 insertions(+), 14 deletions(-)
drivers/staging/panel/panel.c +21 -14
@@ -214,6 +214,10 @@ static pmask_t phys_prev;static char inputs_stable;/* these variables are specific to the keypad */ +static struct { +bool enabled; +} keypad; +static char keypad_buffer[KEYPAD_BUFFER ];static int keypad_buflen;static int keypad_start;
@@ -221,6 +225,9 @@ static char keypressed;static wait_queue_head_t keypad_read_wait;/* lcd-specific variables */ +static struct { +bool enabled; +} lcd;/* contains the LCD config state */ static unsigned long int lcd_flags;
@@ -1395,7 +1402,7 @@ static void panel_lcd_print(const char *s)const char *tmp = s;int count =strlen (s); -if (lcd_enabled && lcd_initialized) { +if (lcd.enabled && lcd_initialized) {for (; count-- >0 ; tmp++) {if (!in_interrupt () && (((count +1 ) &0x1f ) ==0 ))/* let's be a little nice with other processes
@@ -1925,7 +1932,7 @@ static void panel_process_inputs(void)static void panel_scan_timer (void ) { -if (keypad_enabled && keypad_initialized) { +if (keypad.enabled && keypad_initialized) {if (spin_trylock_irq (&pprt_lock)) {phys_scan_contacts ();
@@ -1937,7 +1944,7 @@ static void panel_scan_timer(void)panel_process_inputs (); } -if (lcd_enabled && lcd_initialized) { +if (lcd.enabled && lcd_initialized) {if (keypressed) {if (light_tempo ==0 && ((lcd_flags &LCD_FLAG_L ) ==0 ))lcd_backlight (1 );
@@ -2116,7 +2123,7 @@ static void keypad_init(void)static int panel_notify_sys (struct notifier_block *this,unsigned long code,void *unused) { -if (lcd_enabled && lcd_initialized) { +if (lcd.enabled && lcd_initialized) {switch (code) {case SYS_DOWN : panel_lcd_print
@@ -2172,13 +2179,13 @@ static void panel_attach(struct parport *port)/* must init LCD first, just in case an IRQ from the keypad is * generated at keypad init */ -if (lcd_enabled) { +if (lcd.enabled) {lcd_init ();if (misc_register (&lcd_dev)) goto err_unreg_device; } -if (keypad_enabled) { +if (keypad.enabled) {keypad_init ();if (misc_register (&keypad_dev)) goto err_lcd_unreg;
@@ -2186,7 +2193,7 @@ static void panel_attach(struct parport *port)return ; err_lcd_unreg: -if (lcd_enabled) +if (lcd.enabled)misc_deregister (&lcd_dev); err_unreg_device:parport_unregister_device (pprt);
@@ -2204,12 +2211,12 @@ static void panel_detach(struct parport *port)return ; } -if (keypad_enabled && keypad_initialized) { +if (keypad.enabled && keypad_initialized) {misc_deregister (&keypad_dev); keypad_initialized =0 ; } -if (lcd_enabled && lcd_initialized) { +if (lcd.enabled && lcd_initialized) {misc_deregister (&lcd_dev); lcd_initialized =0 ; }
@@ -2285,8 +2292,8 @@ static int __init panel_init_module(void)break ; } - lcd_enabled = (lcd_type >0 ); - keypad_enabled = (keypad_type >0 ); + lcd.enabled = (lcd_type >0 ); + keypad.enabled = (keypad_type >0 );switch (keypad_type) {case KEYPAD_TYPE_OLD :
@@ -2311,7 +2318,7 @@ static int __init panel_init_module(void)return -EIO ; } -if (!lcd_enabled && !keypad_enabled) { +if (!lcd.enabled && !keypad.enabled) {/* no device enabled, let's release the parport */ if (pprt) {parport_release (pprt);
@@ -2346,12 +2353,12 @@ static void __exit panel_cleanup_module(void)del_timer_sync (&scan_timer);if (pprt !=NULL ) { -if (keypad_enabled) { +if (keypad.enabled) {misc_deregister (&keypad_dev); keypad_initialized =0 ; } -if (lcd_enabled) { +if (lcd.enabled) {panel_lcd_print ("\x0cLCD driver " PANEL_VERSION "\nunloaded.\x1b[Lc\x1b[Lb\x1b[L-" );misc_deregister (&lcd_dev);
Signature · 1 line
2.1.3
Re: [PATCH 5/9] staging: panel: Start making module params read-only
Quoted 5 lines · Mariusz Gorski
Start decoupling module params from the actual device state, both for lcd and keypad, by keeping the params read-only and moving the device state to related structs.
Signed-off-by Mariusz Gorski <[email protected]>
PATCH 6/9 staging: panel: Make two more module params read-only
In reply to Mariusz GorskiMake keypad_type and lcd_type module params read-only. This step also starts making it more clear what is the precedence of device params coming from different sources (device profile, runtime module param values etc).
--- drivers/staging/panel/panel.c | 71 ++++++++++++++++++++++--------------------- 1 file changed, 37 insertions(+), 34 deletions(-)
drivers/staging/panel/panel.c +37 -34
@@ -229,6 +229,9 @@ static struct {bool enabled; } lcd; +/* Needed only for init */ +static int selected_lcd_type =NOT_SET ; +/* contains the LCD config state */ static unsigned long int lcd_flags;/* contains the LCD X offset */
@@ -1417,7 +1420,7 @@ static void panel_lcd_print(const char *s)/* initialize the LCD driver */ static void lcd_init (void ) { -switch (lcd_type) { +switch (selected_lcd_type) {case LCD_TYPE_OLD :/* parallel mode, 8 bits */ if (IS_NOT_SET (lcd_proto))
@@ -2235,28 +2238,21 @@ static struct parport_driver panel_driver = {/* init function */ static int __init panel_init_module (void ) { -/* for backwards compatibility */ -if (IS_NOT_SET (keypad_type)) - keypad_type = keypad_enabled; - -if (IS_NOT_SET (lcd_type)) - lcd_type = lcd_enabled; +int selected_keypad_type =NOT_SET ;/* take care of an eventual profile */ switch (profile) {case PANEL_PROFILE_CUSTOM :/* custom profile */ -if (IS_NOT_SET (keypad_type)) - keypad_type =DEFAULT_KEYPAD_TYPE ; -if (IS_NOT_SET (lcd_type)) - lcd_type =DEFAULT_LCD_TYPE ; + selected_keypad_type =DEFAULT_KEYPAD_TYPE ; + selected_lcd_type =DEFAULT_LCD_TYPE ;break ;case PANEL_PROFILE_OLD :/* 8 bits, 2*16, old keypad */ -if (IS_NOT_SET (keypad_type)) - keypad_type =KEYPAD_TYPE_OLD ; -if (IS_NOT_SET (lcd_type)) - lcd_type =LCD_TYPE_OLD ; + selected_keypad_type =KEYPAD_TYPE_OLD ; + selected_lcd_type =LCD_TYPE_OLD ; + +/* TODO: This two are a little hacky, sort it out later */ if (IS_NOT_SET (lcd_width)) lcd_width =16 ;if (IS_NOT_SET (lcd_hwidth))
@@ -2264,38 +2260,45 @@ static int __init panel_init_module(void)break ;case PANEL_PROFILE_NEW :/* serial, 2*16, new keypad */ -if (IS_NOT_SET (keypad_type)) - keypad_type =KEYPAD_TYPE_NEW ; -if (IS_NOT_SET (lcd_type)) - lcd_type =LCD_TYPE_KS0074 ; + selected_keypad_type =KEYPAD_TYPE_NEW ; + selected_lcd_type =LCD_TYPE_KS0074 ;break ;case PANEL_PROFILE_HANTRONIX :/* 8 bits, 2*16 hantronix-like, no keypad */ -if (IS_NOT_SET (keypad_type)) - keypad_type =KEYPAD_TYPE_NONE ; -if (IS_NOT_SET (lcd_type)) - lcd_type =LCD_TYPE_HANTRONIX ; + selected_keypad_type =KEYPAD_TYPE_NONE ; + selected_lcd_type =LCD_TYPE_HANTRONIX ;break ;case PANEL_PROFILE_NEXCOM :/* generic 8 bits, 2*16, nexcom keypad, eg. Nexcom. */ -if (IS_NOT_SET (keypad_type)) - keypad_type =KEYPAD_TYPE_NEXCOM ; -if (IS_NOT_SET (lcd_type)) - lcd_type =LCD_TYPE_NEXCOM ; + selected_keypad_type =KEYPAD_TYPE_NEXCOM ; + selected_lcd_type =LCD_TYPE_NEXCOM ;break ;case PANEL_PROFILE_LARGE :/* 8 bits, 2*40, old keypad */ -if (IS_NOT_SET (keypad_type)) - keypad_type =KEYPAD_TYPE_OLD ; -if (IS_NOT_SET (lcd_type)) - lcd_type =LCD_TYPE_OLD ; + selected_keypad_type =KEYPAD_TYPE_OLD ; + selected_lcd_type =LCD_TYPE_OLD ;break ; } - lcd.enabled = (lcd_type >0 ); - keypad.enabled = (keypad_type >0 ); +/* +* Overwrite selection with module param values (both keypad and lcd), +* where the deprecated params have lower prio. +*/ +if (keypad_enabled >-1 ) + selected_keypad_type = keypad_enabled; +if (keypad_type >-1 ) + selected_keypad_type = keypad_type; + + keypad.enabled = (selected_keypad_type >0 ); + +if (lcd_enabled >-1 ) + selected_lcd_type = lcd_enabled; +if (lcd_type >-1 ) + selected_lcd_type = lcd_type; + + lcd.enabled = (selected_lcd_type >0 ); -switch (keypad_type) { +switch (selected_keypad_type) {case KEYPAD_TYPE_OLD : keypad_profile = old_keypad_profile;break ;
Signature · 1 line
2.1.3
Re: [PATCH 6/9] staging: panel: Make two more module params read-only
Quoted 25 lines · Mariusz Gorski
Make
keypad_typeandlcd_typemodule params read-only. This step also starts making it more clear what is the precedence of device params coming from different sources (device profile, runtime module param values etc).Signed-off-by Mariusz Gorski <[email protected]>--- drivers/staging/panel/panel.c | 71 ++++++++++++++++++++++--------------------- 1 file changed, 37 insertions(+), 34 deletions(-)drivers/staging/panel/panel.c +3
-0@@ -229,6 +229,9 @@ static struct {bool enabled; } lcd; +/* Needed only for init */ +static int selected_lcd_type =NOT_SET ; +/* contains the LCD config state */ static unsigned long int lcd_flags;/* contains the LCD X offset */
drivers/staging/panel/panel.c static void panel_lcd_print(const char *s) · line 1423
Quoted 5 lines
drivers/staging/panel/panel.c +1
-1@@ -1417,7 +1420,7 @@ static void panel_lcd_print(const char *s)/* initialize the LCD driver */ static void lcd_init (void ) { -switch (lcd_type) { +switch (selected_lcd_type) {
(...)
stupid question : why not move that to the lcd struct you just created instead of creating a new variable ? It would make sense to me to have lcd.type here just like you did with enabled. Same for keypad.
Willy
Re: [PATCH 6/9] staging: panel: Make two more module params read-only
Quoted 34 lines · Willy Tarreau
Quoted 30 lines · Mariusz Gorski
Make
keypad_typeandlcd_typemodule params read-only. This step also starts making it more clear what is the precedence of device params coming from different sources (device profile, runtime module param values etc).Signed-off-by Mariusz Gorski <[email protected]>--- drivers/staging/panel/panel.c | 71 ++++++++++++++++++++++--------------------- 1 file changed, 37 insertions(+), 34 deletions(-)drivers/staging/panel/panel.c +4
-1@@ -229,6 +229,9 @@ static struct {bool enabled; } lcd; +/* Needed only for init */ +static int selected_lcd_type =NOT_SET ; +/* contains the LCD config state */ static unsigned long int lcd_flags;/* contains the LCD X offset */ @@ -1417,7 +1420,7 @@ static void panel_lcd_print(const char *s)/* initialize the LCD driver */ static void lcd_init (void ) { -switch (lcd_type) { +switch (selected_lcd_type) {(...)
Quoted 7 lines
stupid question : why not move that to the lcd struct you just created instead of creating a new variable ? It would make sense to me to have lcd.type here just like you did with enabled. Same for keypad.
Willy
I get your point here. This var is here only because it's set in init_panel_module() and then used in lcd_init(). So it's needed really only for the init code. It doesn't directly_ describe the lcd's state, so I decided to keep it out.
Thanks,
Mariusz
Re: [PATCH 6/9] staging: panel: Make two more module params read-only
Quoted 40 lines · Mariusz Gorski
Quoted 39 lines · Willy Tarreau
Quoted 25 lines · Mariusz Gorski
Make
keypad_typeandlcd_typemodule params read-only. This step also starts making it more clear what is the precedence of device params coming from different sources (device profile, runtime module param values etc).Signed-off-by Mariusz Gorski <[email protected]>--- drivers/staging/panel/panel.c | 71 ++++++++++++++++++++++--------------------- 1 file changed, 37 insertions(+), 34 deletions(-)drivers/staging/panel/panel.c +3
-0@@ -229,6 +229,9 @@ static struct {bool enabled; } lcd; +/* Needed only for init */ +static int selected_lcd_type =NOT_SET ; +/* contains the LCD config state */ static unsigned long int lcd_flags;/* contains the LCD X offset */ drivers/staging/panel/panel.c static void panel_lcd_print(const char *s) · line 1423
Quoted 5 lines
drivers/staging/panel/panel.c +1
-1@@ -1417,7 +1420,7 @@ static void panel_lcd_print(const char *s)/* initialize the LCD driver */ static void lcd_init (void ) { -switch (lcd_type) { +switch (selected_lcd_type) {(...)
stupid question : why not move that to the lcd struct you just created instead of creating a new variable ? It would make sense to me to have lcd.type here just like you did with enabled. Same for keypad.
Quoted 7 lines
Quoted 2 lines
Willy
I get your point here. This var is here only because it's set in
init_panel_module()and then used inlcd_init(). So it's needed really only for the init code. It doesn'tdirectly_describe the lcd's state, so I decided to keep it out.
OK but isn't it the same for some of the other variables you moved there ? Anyway that's not important, I have nothing against this, it was just a question.
Willy
PATCH 7/9 staging: panel: Refactor LCD init code
In reply to Mariusz GorskiRework lcd_init method to make it a little bit more clear about the precedence of the params, move LCD geometry and pins layout to the LCD struct and thus make the LCD-related module params effectively read-only.
--- drivers/staging/panel/panel.c | 304 ++++++++++++++++++++++-------------------- 1 file changed, 163 insertions(+), 141 deletions(-)
drivers/staging/panel/panel.c +163 -141
@@ -227,6 +227,21 @@ static wait_queue_head_t keypad_read_wait;/* lcd-specific variables */ static struct {bool enabled; +int height; +int width; +int bwidth; +int hwidth; +int charset; +int proto; +/* TODO: use union here? */ +struct { +int e; +int rs; +int rw; +int cl; +int da; +int bl; + } pins; } lcd;/* Needed only for init */
@@ -768,7 +783,7 @@ static void lcd_send_serial(int byte)/* turn the backlight on or off */ static void lcd_backlight (int on) { -if (lcd_bl_pin ==PIN_NONE ) +if (lcd.pins.bl ==PIN_NONE )return ;/* The backlight is activated by setting the AUTOFEED line to +5V */
@@ -867,23 +882,23 @@ static void lcd_write_data_tilcd(int data)static void lcd_gotoxy (void ) {lcd_write_cmd (0x80 /* set DDRAM address */ - | (lcd_addr_y ? lcd_hwidth :0 ) + | (lcd_addr_y ? lcd.hwidth :0 )/* we force the cursor to stay at the end of the line if it wants to go farther */ - | ((lcd_addr_x < lcd_bwidth) ? lcd_addr_x & - (lcd_hwidth -1 ) : lcd_bwidth -1 )); + | ((lcd_addr_x < lcd.bwidth) ? lcd_addr_x & + (lcd.hwidth -1 ) : lcd.bwidth -1 )); }static void lcd_print (char c) { -if (lcd_addr_x < lcd_bwidth) { +if (lcd_addr_x < lcd.bwidth) {if (lcd_char_conv !=NULL ) c = lcd_char_conv[(unsigned char )c];lcd_write_data (c); lcd_addr_x++; }/* prevents the cursor from wrapping onto the next line */ -if (lcd_addr_x == lcd_bwidth) +if (lcd_addr_x == lcd.bwidth)lcd_gotoxy (); }
@@ -897,7 +912,7 @@ static void lcd_clear_fast_s(void)lcd_gotoxy ();spin_lock_irq (&pprt_lock); -for (pos =0 ; pos < lcd_height * lcd_hwidth; pos++) { +for (pos =0 ; pos < lcd.height * lcd.hwidth; pos++) {lcd_send_serial (0x5F );/* R/W=W, RS=1 */ lcd_send_serial (' ' &0x0F );lcd_send_serial ((' ' >>4 ) &0x0F );
@@ -920,7 +935,7 @@ static void lcd_clear_fast_p8(void)lcd_gotoxy ();spin_lock_irq (&pprt_lock); -for (pos =0 ; pos < lcd_height * lcd_hwidth; pos++) { +for (pos =0 ; pos < lcd.height * lcd.hwidth; pos++) {/* present the data to the data port */ w_dtr (pprt,' ' );
@@ -958,7 +973,7 @@ static void lcd_clear_fast_tilcd(void)lcd_gotoxy ();spin_lock_irq (&pprt_lock); -for (pos =0 ; pos < lcd_height * lcd_hwidth; pos++) { +for (pos =0 ; pos < lcd.height * lcd.hwidth; pos++) {/* present the data to the data port */ w_dtr (pprt,' ' );udelay (60 );
@@ -983,7 +998,7 @@ static void lcd_clear_display(void)static void lcd_init_display (void ) { - lcd_flags = ((lcd_height >1 ) ?LCD_FLAG_N :0 ) + lcd_flags = ((lcd.height >1 ) ?LCD_FLAG_N :0 ) |LCD_FLAG_D |LCD_FLAG_C |LCD_FLAG_B ;long_sleep (20 );/* wait 20 ms after power-up for the paranoid */
@@ -1097,17 +1112,17 @@ static inline int handle_lcd_special_code(void)case 'l' :/* Shift Cursor Left */ if (lcd_addr_x >0 ) {/* back one char if not at end of line */ -if (lcd_addr_x < lcd_bwidth) +if (lcd_addr_x < lcd.bwidth)lcd_write_cmd (0x10 ); lcd_addr_x--; } processed =1 ;break ;case 'r' :/* shift cursor right */ -if (lcd_addr_x < lcd_width) { +if (lcd_addr_x < lcd.width) {/* allow the cursor to pass the end of the line */ if (lcd_addr_x < - (lcd_bwidth -1 )) + (lcd.bwidth -1 ))lcd_write_cmd (0x14 ); lcd_addr_x++; }
@@ -1126,7 +1141,7 @@ static inline int handle_lcd_special_code(void)case 'k' : {/* kill end of line */ int x; -for (x = lcd_addr_x; x < lcd_bwidth; x++) +for (x = lcd_addr_x; x < lcd.bwidth; x++)lcd_write_data (' ' );/* restore cursor position */
@@ -1274,7 +1289,7 @@ static void lcd_write_char(char c)if (lcd_addr_x >0 ) {/* check if we're not at the end of the line */ -if (lcd_addr_x < lcd_bwidth) +if (lcd_addr_x < lcd.bwidth)/* back one char */ lcd_write_cmd (0x10 ); lcd_addr_x--;
@@ -1291,10 +1306,10 @@ static void lcd_write_char(char c)case '\n' :/* flush the remainder of the current line and go to the beginning of the next line */ -for (; lcd_addr_x < lcd_bwidth; lcd_addr_x++) +for (; lcd_addr_x < lcd.bwidth; lcd_addr_x++)lcd_write_data (' ' ); lcd_addr_x =0 ; - lcd_addr_y = (lcd_addr_y +1 ) % lcd_height; + lcd_addr_y = (lcd_addr_y +1 ) % lcd.height;lcd_gotoxy ();break ;case '\r' :
@@ -1423,174 +1438,164 @@ static void lcd_init(void)switch (selected_lcd_type) {case LCD_TYPE_OLD :/* parallel mode, 8 bits */ -if (IS_NOT_SET (lcd_proto)) - lcd_proto =LCD_PROTO_PARALLEL ; -if (IS_NOT_SET (lcd_charset)) - lcd_charset =LCD_CHARSET_NORMAL ; -if (lcd_e_pin ==PIN_NOT_SET ) - lcd_e_pin =PIN_STROBE ; -if (lcd_rs_pin ==PIN_NOT_SET ) - lcd_rs_pin =PIN_AUTOLF ; - -if (IS_NOT_SET (lcd_width)) - lcd_width =40 ; -if (IS_NOT_SET (lcd_bwidth)) - lcd_bwidth =40 ; -if (IS_NOT_SET (lcd_hwidth)) - lcd_hwidth =64 ; -if (IS_NOT_SET (lcd_height)) - lcd_height =2 ; + lcd.proto =LCD_PROTO_PARALLEL ; + lcd.charset =LCD_CHARSET_NORMAL ; + lcd.pins.e =PIN_STROBE ; + lcd.pins.rs =PIN_AUTOLF ; + + lcd.width =40 ; + lcd.bwidth =40 ; + lcd.hwidth =64 ; + lcd.height =2 ;break ;case LCD_TYPE_KS0074 :/* serial mode, ks0074 */ -if (IS_NOT_SET (lcd_proto)) - lcd_proto =LCD_PROTO_SERIAL ; -if (IS_NOT_SET (lcd_charset)) - lcd_charset =LCD_CHARSET_KS0074 ; -if (lcd_bl_pin ==PIN_NOT_SET ) - lcd_bl_pin =PIN_AUTOLF ; -if (lcd_cl_pin ==PIN_NOT_SET ) - lcd_cl_pin =PIN_STROBE ; -if (lcd_da_pin ==PIN_NOT_SET ) - lcd_da_pin =PIN_D0 ; - -if (IS_NOT_SET (lcd_width)) - lcd_width =16 ; -if (IS_NOT_SET (lcd_bwidth)) - lcd_bwidth =40 ; -if (IS_NOT_SET (lcd_hwidth)) - lcd_hwidth =16 ; -if (IS_NOT_SET (lcd_height)) - lcd_height =2 ; + lcd.proto =LCD_PROTO_SERIAL ; + lcd.charset =LCD_CHARSET_KS0074 ; + lcd.pins.bl =PIN_AUTOLF ; + lcd.pins.cl =PIN_STROBE ; + lcd.pins.da =PIN_D0 ; + + lcd.width =16 ; + lcd.bwidth =40 ; + lcd.hwidth =16 ; + lcd.height =2 ;break ;case LCD_TYPE_NEXCOM :/* parallel mode, 8 bits, generic */ -if (IS_NOT_SET (lcd_proto)) - lcd_proto =LCD_PROTO_PARALLEL ; -if (IS_NOT_SET (lcd_charset)) - lcd_charset =LCD_CHARSET_NORMAL ; -if (lcd_e_pin ==PIN_NOT_SET ) - lcd_e_pin =PIN_AUTOLF ; -if (lcd_rs_pin ==PIN_NOT_SET ) - lcd_rs_pin =PIN_SELECP ; -if (lcd_rw_pin ==PIN_NOT_SET ) - lcd_rw_pin =PIN_INITP ; - -if (IS_NOT_SET (lcd_width)) - lcd_width =16 ; -if (IS_NOT_SET (lcd_bwidth)) - lcd_bwidth =40 ; -if (IS_NOT_SET (lcd_hwidth)) - lcd_hwidth =64 ; -if (IS_NOT_SET (lcd_height)) - lcd_height =2 ; + lcd.proto =LCD_PROTO_PARALLEL ; + lcd.charset =LCD_CHARSET_NORMAL ; + lcd.pins.e =PIN_AUTOLF ; + lcd.pins.rs =PIN_SELECP ; + lcd.pins.rw =PIN_INITP ; + + lcd.width =16 ; + lcd.bwidth =40 ; + lcd.hwidth =64 ; + lcd.height =2 ;break ;case LCD_TYPE_CUSTOM :/* customer-defined */ -if (IS_NOT_SET (lcd_proto)) - lcd_proto =DEFAULT_LCD_PROTO ; -if (IS_NOT_SET (lcd_charset)) - lcd_charset =DEFAULT_LCD_CHARSET ; + lcd.proto =DEFAULT_LCD_PROTO ; + lcd.charset =DEFAULT_LCD_CHARSET ;/* default geometry will be set later */ break ;case LCD_TYPE_HANTRONIX :/* parallel mode, 8 bits, hantronix-like */ default : -if (IS_NOT_SET (lcd_proto)) - lcd_proto =LCD_PROTO_PARALLEL ; -if (IS_NOT_SET (lcd_charset)) - lcd_charset =LCD_CHARSET_NORMAL ; -if (lcd_e_pin ==PIN_NOT_SET ) - lcd_e_pin =PIN_STROBE ; -if (lcd_rs_pin ==PIN_NOT_SET ) - lcd_rs_pin =PIN_SELECP ; - -if (IS_NOT_SET (lcd_width)) - lcd_width =16 ; -if (IS_NOT_SET (lcd_bwidth)) - lcd_bwidth =40 ; -if (IS_NOT_SET (lcd_hwidth)) - lcd_hwidth =64 ; -if (IS_NOT_SET (lcd_height)) - lcd_height =2 ; + lcd.proto =LCD_PROTO_PARALLEL ; + lcd.charset =LCD_CHARSET_NORMAL ; + lcd.pins.e =PIN_STROBE ; + lcd.pins.rs =PIN_SELECP ; + + lcd.width =16 ; + lcd.bwidth =40 ; + lcd.hwidth =64 ; + lcd.height =2 ;break ; } +/* Overwrite with module params set on loading */ +if (lcd_height >-1 ) + lcd.height = lcd_height; +if (lcd_width >-1 ) + lcd.width = lcd_width; +if (lcd_bwidth >-1 ) + lcd.bwidth = lcd_bwidth; +if (lcd_hwidth >-1 ) + lcd.hwidth = lcd_hwidth; +if (lcd_charset >-1 ) + lcd.charset = lcd_charset; +if (lcd_proto >-1 ) + lcd.proto = lcd_proto; +if (lcd_e_pin !=PIN_NOT_SET ) + lcd.pins.e = lcd_e_pin; +if (lcd_rs_pin !=PIN_NOT_SET ) + lcd.pins.rs = lcd_rs_pin; +if (lcd_rw_pin !=PIN_NOT_SET ) + lcd.pins.rw = lcd_rw_pin; +if (lcd_cl_pin !=PIN_NOT_SET ) + lcd.pins.cl = lcd_cl_pin; +if (lcd_da_pin !=PIN_NOT_SET ) + lcd.pins.da = lcd_da_pin; +if (lcd_bl_pin !=PIN_NOT_SET ) + lcd.pins.bl = lcd_bl_pin; +/* this is used to catch wrong and default values */ -if (lcd_width <=0 ) - lcd_width =DEFAULT_LCD_WIDTH ; -if (lcd_bwidth <=0 ) - lcd_bwidth =DEFAULT_LCD_BWIDTH ; -if (lcd_hwidth <=0 ) - lcd_hwidth =DEFAULT_LCD_HWIDTH ; -if (lcd_height <=0 ) - lcd_height =DEFAULT_LCD_HEIGHT ; - -if (lcd_proto ==LCD_PROTO_SERIAL ) {/* SERIAL */ +if (lcd.width <=0 ) + lcd.width =DEFAULT_LCD_WIDTH ; +if (lcd.bwidth <=0 ) + lcd.bwidth =DEFAULT_LCD_BWIDTH ; +if (lcd.hwidth <=0 ) + lcd.hwidth =DEFAULT_LCD_HWIDTH ; +if (lcd.height <=0 ) + lcd.height =DEFAULT_LCD_HEIGHT ; + +if (lcd.proto ==LCD_PROTO_SERIAL ) {/* SERIAL */ lcd_write_cmd = lcd_write_cmd_s; lcd_write_data = lcd_write_data_s; lcd_clear_fast = lcd_clear_fast_s; -if (lcd_cl_pin ==PIN_NOT_SET ) - lcd_cl_pin =DEFAULT_LCD_PIN_SCL ; -if (lcd_da_pin ==PIN_NOT_SET ) - lcd_da_pin =DEFAULT_LCD_PIN_SDA ; +if (lcd.pins.cl ==PIN_NOT_SET ) + lcd.pins.cl =DEFAULT_LCD_PIN_SCL ; +if (lcd.pins.da ==PIN_NOT_SET ) + lcd.pins.da =DEFAULT_LCD_PIN_SDA ; - }else if (lcd_proto ==LCD_PROTO_PARALLEL ) {/* PARALLEL */ + }else if (lcd.proto ==LCD_PROTO_PARALLEL ) {/* PARALLEL */ lcd_write_cmd = lcd_write_cmd_p8; lcd_write_data = lcd_write_data_p8; lcd_clear_fast = lcd_clear_fast_p8; -if (lcd_e_pin ==PIN_NOT_SET ) - lcd_e_pin =DEFAULT_LCD_PIN_E ; -if (lcd_rs_pin ==PIN_NOT_SET ) - lcd_rs_pin =DEFAULT_LCD_PIN_RS ; -if (lcd_rw_pin ==PIN_NOT_SET ) - lcd_rw_pin =DEFAULT_LCD_PIN_RW ; +if (lcd.pins.e ==PIN_NOT_SET ) + lcd.pins.e =DEFAULT_LCD_PIN_E ; +if (lcd.pins.rs ==PIN_NOT_SET ) + lcd.pins.rs =DEFAULT_LCD_PIN_RS ; +if (lcd.pins.rw ==PIN_NOT_SET ) + lcd.pins.rw =DEFAULT_LCD_PIN_RW ; }else { lcd_write_cmd = lcd_write_cmd_tilcd; lcd_write_data = lcd_write_data_tilcd; lcd_clear_fast = lcd_clear_fast_tilcd; } -if (lcd_bl_pin ==PIN_NOT_SET ) - lcd_bl_pin =DEFAULT_LCD_PIN_BL ; - -if (lcd_e_pin ==PIN_NOT_SET ) - lcd_e_pin =PIN_NONE ; -if (lcd_rs_pin ==PIN_NOT_SET ) - lcd_rs_pin =PIN_NONE ; -if (lcd_rw_pin ==PIN_NOT_SET ) - lcd_rw_pin =PIN_NONE ; -if (lcd_bl_pin ==PIN_NOT_SET ) - lcd_bl_pin =PIN_NONE ; -if (lcd_cl_pin ==PIN_NOT_SET ) - lcd_cl_pin =PIN_NONE ; -if (lcd_da_pin ==PIN_NOT_SET ) - lcd_da_pin =PIN_NONE ; - -if (IS_NOT_SET (lcd_charset)) - lcd_charset =DEFAULT_LCD_CHARSET ; - -if (lcd_charset ==LCD_CHARSET_KS0074 ) +if (lcd.pins.bl ==PIN_NOT_SET ) + lcd.pins.bl =DEFAULT_LCD_PIN_BL ; + +if (lcd.pins.e ==PIN_NOT_SET ) + lcd.pins.e =PIN_NONE ; +if (lcd.pins.rs ==PIN_NOT_SET ) + lcd.pins.rs =PIN_NONE ; +if (lcd.pins.rw ==PIN_NOT_SET ) + lcd.pins.rw =PIN_NONE ; +if (lcd.pins.bl ==PIN_NOT_SET ) + lcd.pins.bl =PIN_NONE ; +if (lcd.pins.cl ==PIN_NOT_SET ) + lcd.pins.cl =PIN_NONE ; +if (lcd.pins.da ==PIN_NOT_SET ) + lcd.pins.da =PIN_NONE ; + +if (IS_NOT_SET (lcd.charset)) + lcd.charset =DEFAULT_LCD_CHARSET ; + +if (lcd.charset ==LCD_CHARSET_KS0074 ) lcd_char_conv = lcd_char_conv_ks0074;else lcd_char_conv =NULL ; -if (lcd_bl_pin !=PIN_NONE ) +if (lcd.pins.bl !=PIN_NONE )init_scan_timer (); -pin_to_bits (lcd_e_pin, lcd_bits[LCD_PORT_D ][LCD_BIT_E ], +pin_to_bits (lcd.pins.e, lcd_bits[LCD_PORT_D ][LCD_BIT_E ], lcd_bits[LCD_PORT_C ][LCD_BIT_E ]); -pin_to_bits (lcd_rs_pin, lcd_bits[LCD_PORT_D ][LCD_BIT_RS ], +pin_to_bits (lcd.pins.rs, lcd_bits[LCD_PORT_D ][LCD_BIT_RS ], lcd_bits[LCD_PORT_C ][LCD_BIT_RS ]); -pin_to_bits (lcd_rw_pin, lcd_bits[LCD_PORT_D ][LCD_BIT_RW ], +pin_to_bits (lcd.pins.rw, lcd_bits[LCD_PORT_D ][LCD_BIT_RW ], lcd_bits[LCD_PORT_C ][LCD_BIT_RW ]); -pin_to_bits (lcd_bl_pin, lcd_bits[LCD_PORT_D ][LCD_BIT_BL ], +pin_to_bits (lcd.pins.bl, lcd_bits[LCD_PORT_D ][LCD_BIT_BL ], lcd_bits[LCD_PORT_C ][LCD_BIT_BL ]); -pin_to_bits (lcd_cl_pin, lcd_bits[LCD_PORT_D ][LCD_BIT_CL ], +pin_to_bits (lcd.pins.cl, lcd_bits[LCD_PORT_D ][LCD_BIT_CL ], lcd_bits[LCD_PORT_C ][LCD_BIT_CL ]); -pin_to_bits (lcd_da_pin, lcd_bits[LCD_PORT_D ][LCD_BIT_DA ], +pin_to_bits (lcd.pins.da, lcd_bits[LCD_PORT_D ][LCD_BIT_DA ], lcd_bits[LCD_PORT_C ][LCD_BIT_DA ]);/* before this line, we must NOT send anything to the display.
@@ -2281,6 +2286,23 @@ static int __init panel_init_module(void) }/* +* Init lcd struct with load-time values to preserve exact current +* functionality (at least for now). +*/ + lcd.height = lcd_height; + lcd.width = lcd_width; + lcd.bwidth = lcd_bwidth; + lcd.hwidth = lcd_hwidth; + lcd.charset = lcd_charset; + lcd.proto = lcd_proto; + lcd.pins.e = lcd_e_pin; + lcd.pins.rs = lcd_rs_pin; + lcd.pins.rw = lcd_rw_pin; + lcd.pins.cl = lcd_cl_pin; + lcd.pins.da = lcd_da_pin; + lcd.pins.bl = lcd_bl_pin; + +/* * Overwrite selection with module param values (both keypad and lcd), * where the deprecated params have lower prio. */
Signature · 1 line
2.1.3
Re: [PATCH 7/9] staging: panel: Refactor LCD init code
Quoted 6 lines · Mariusz Gorski
Rework
lcd_initmethod to make it a little bit more clear about the precedence of the params, move LCD geometry and pins layout to the LCD struct and thus make the LCD-related module params effectively read-only.Signed-off-by Mariusz Gorski <[email protected]>
I like this refactoring. However I don't know if you got your LCD module to work or not, but for such important changes you should definitely test the code, since it's very easy to introduce minor bugs or even to fix a bug that used to make the whole driver work...
Willy
Re: [PATCH 7/9] staging: panel: Refactor LCD init code
Quoted 8 lines · Willy Tarreau
Quoted 6 lines · Mariusz Gorski
Rework
lcd_initmethod to make it a little bit more clear about the precedence of the params, move LCD geometry and pins layout to the LCD struct and thus make the LCD-related module params effectively read-only.Signed-off-by Mariusz Gorski <[email protected]>
Quoted 9 lines
Acked-by Willy Tarreau <[email protected]>I like this refactoring. However I don't know if you got your LCD module to work or not, but for such important changes you should definitely test the code, since it's very easy to introduce minor bugs or even to fix a bug that used to make the whole driver work...
Willy
Yes, I have tested this code with my LCD module and it works as before. This is what I've emphasized in the cover letter -
- I made sure (and tested), that all lcd and keypad params are set to the same state as before this patch series, and that the current behaviour of the module doesn't change. I've tested all profile/lcd_type combinations in an automated way to catch any edge cases :)
Thanks,
Mariusz
Re: [PATCH 7/9] staging: panel: Refactor LCD init code
Quoted 16 lines · Mariusz Gorski
Quoted 15 lines · Willy Tarreau
Quoted 6 lines · Mariusz Gorski
Rework
lcd_initmethod to make it a little bit more clear about the precedence of the params, move LCD geometry and pins layout to the LCD struct and thus make the LCD-related module params effectively read-only.Signed-off-by Mariusz Gorski <[email protected]>Acked-by Willy Tarreau <[email protected]>I like this refactoring. However I don't know if you got your LCD module to work or not, but for such important changes you should definitely test the code, since it's very easy to introduce minor bugs or even to fix a bug that used to make the whole driver work...
Quoted 4 lines
Quoted 2 lines
Willy
Yes, I have tested this code with my LCD module and it works as before.
great!
Quoted 6 lines
This is what I've emphasized in the cover letter -
- I made sure (and tested), that all lcd and keypad params are set to the same state as before this patch series, and that the current behaviour of the module doesn't change. I've tested all profile/lcd_type combinations in an automated way to catch any edge cases :)
"tested" was not mentionned in the cover letter, hence my asking :-)
Willy
PATCH 8/9 staging: panel: Remove more magic number comparison
In reply to Mariusz GorskiUse a macro instead of magic number comparison for checking whether a module param value has been set.
--- drivers/staging/panel/panel.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)
drivers/staging/panel/panel.c +11 -10
@@ -136,6 +136,7 @@#define NOT_SET -1#define IS_NOT_SET (x) (x == NOT_SET) +#define IS_SET (x) (x > NOT_SET)/* macros to simplify use of the parallel port */ #define r_ctr (x) (parport_read_control((x)->port))
@@ -1496,17 +1497,17 @@ static void lcd_init(void) }/* Overwrite with module params set on loading */ -if (lcd_height >-1 ) +if (IS_SET (lcd_height)) lcd.height = lcd_height; -if (lcd_width >-1 ) +if (IS_SET (lcd_width)) lcd.width = lcd_width; -if (lcd_bwidth >-1 ) +if (IS_SET (lcd_bwidth)) lcd.bwidth = lcd_bwidth; -if (lcd_hwidth >-1 ) +if (IS_SET (lcd_hwidth)) lcd.hwidth = lcd_hwidth; -if (lcd_charset >-1 ) +if (IS_SET (lcd_charset)) lcd.charset = lcd_charset; -if (lcd_proto >-1 ) +if (IS_SET (lcd_proto)) lcd.proto = lcd_proto;if (lcd_e_pin !=PIN_NOT_SET ) lcd.pins.e = lcd_e_pin;
@@ -2306,16 +2307,16 @@ static int __init panel_init_module(void)* Overwrite selection with module param values (both keypad and lcd), * where the deprecated params have lower prio. */ -if (keypad_enabled >-1 ) +if (IS_SET (keypad_enabled)) selected_keypad_type = keypad_enabled; -if (keypad_type >-1 ) +if (IS_SET (keypad_type)) selected_keypad_type = keypad_type; keypad.enabled = (selected_keypad_type >0 ); -if (lcd_enabled >-1 ) +if (IS_SET (lcd_enabled)) selected_lcd_type = lcd_enabled; -if (lcd_type >-1 ) +if (IS_SET (lcd_type)) selected_lcd_type = lcd_type; lcd.enabled = (selected_lcd_type >0 );
Signature · 1 line
2.1.3
Re: [PATCH 8/9] staging: panel: Remove more magic number comparison
Quoted 21 lines · Mariusz Gorski
Use a macro instead of magic number comparison for checking whether a module param value has been set.
Signed-off-by Mariusz Gorski <[email protected]>--- drivers/staging/panel/panel.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)drivers/staging/panel/panel.c +1
-0@@ -136,6 +136,7 @@#define NOT_SET -1#define IS_NOT_SET (x) (x == NOT_SET) +#define IS_SET (x) (x > NOT_SET)/* macros to simplify use of the parallel port */ #define r_ctr (x) (parport_read_control((x)->port))
drivers/staging/panel/panel.c static void lcd_init(void) · line 1503
Quoted 9 lines
drivers/staging/panel/panel.c +2
-2@@ -1496,17 +1497,17 @@ static void lcd_init(void) }/* Overwrite with module params set on loading */ -if (lcd_height >-1 ) +if (IS_SET (lcd_height)) lcd.height = lcd_height; -if (lcd_width >-1 ) +if (IS_SET (lcd_width)) lcd.width = lcd_width;
(...)
Same as for the other patch, better open-code the test for readability :
- if (lcd_height > -1)
+ if (lcd_height != NOT_SET)
lcd.height = lcd_height;
Note that we take the freedom to change the operator since we only want to check equality and not sign in practice.
Willy
Re: [PATCH 8/9] staging: panel: Remove more magic number comparison
Quoted 40 lines · Willy Tarreau
Quoted 21 lines · Mariusz Gorski
Use a macro instead of magic number comparison for checking whether a module param value has been set.
Signed-off-by Mariusz Gorski <[email protected]>--- drivers/staging/panel/panel.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)drivers/staging/panel/panel.c +1
-0@@ -136,6 +136,7 @@#define NOT_SET -1#define IS_NOT_SET (x) (x == NOT_SET) +#define IS_SET (x) (x > NOT_SET)/* macros to simplify use of the parallel port */ #define r_ctr (x) (parport_read_control((x)->port))drivers/staging/panel/panel.c static void lcd_init(void) · line 1503
Quoted 9 lines
drivers/staging/panel/panel.c +2
-2@@ -1496,17 +1497,17 @@ static void lcd_init(void) }/* Overwrite with module params set on loading */ -if (lcd_height >-1 ) +if (IS_SET (lcd_height)) lcd.height = lcd_height; -if (lcd_width >-1 ) +if (IS_SET (lcd_width)) lcd.width = lcd_width;(...)
Same as for the other patch, better open-code the test for readability :
drivers/staging/panel/panel.c +1
-1-if (lcd_height >-1 ) +if (lcd_height !=NOT_SET ) lcd.height = lcd_height;
Quoted 5 lines
Note that we take the freedom to change the operator since we only want to check equality and not sign in practice.
Willy
Good point, will apply :)
Thanks,
Mariusz
PATCH 9/9 staging: panel: Move LCD-related state into struct lcd
In reply to Mariusz GorskiMove more or less all LCD-related state into struct lcd in order to get better cohesion; use bool instead of int where it makes sense.
--- drivers/staging/panel/panel.c | 255 ++++++++++++++++++++++-------------------- 1 file changed, 134 insertions(+), 121 deletions(-)
drivers/staging/panel/panel.c +134 -121
@@ -228,12 +228,20 @@ static wait_queue_head_t keypad_read_wait;/* lcd-specific variables */ static struct { bool enabled; + bool initialized; + bool must_clear; + + /* TODO: use bool here? */ + char left_shift; + int height; int width; int bwidth; int hwidth; int charset; int proto; + int light_tempo; + /* TODO: use union here? */ struct { int e;
@@ -243,22 +251,26 @@ static struct {int da;int bl; } pins; + +/* contains the LCD config state */ +unsigned long int flags; + +/* Contains the LCD X and Y offset */ +struct { +unsigned long int x; +unsigned long int y; + } addr; + +/* Current escape sequence and it's length or -1 if outside */ +struct { +char buf[LCD_ESCAPE_LEN +1 ]; +int len; + } esc_seq; } lcd;/* Needed only for init */ static int selected_lcd_type =NOT_SET ; -/* contains the LCD config state */ -static unsigned long int lcd_flags; -/* contains the LCD X offset */ -static unsigned long int lcd_addr_x; -/* contains the LCD Y offset */ -static unsigned long int lcd_addr_y; -/* current escape sequence, 0 terminated */ -static char lcd_escape[LCD_ESCAPE_LEN +1 ]; -/* not in escape state. >=0 = escape cmd len */ -static int lcd_escape_len =-1 ; -/* * Bit masks to convert LCD signals to parallel port outputs. * _d_ are values for data port, _c_ are for control port.
@@ -441,13 +453,8 @@ static atomic_t keypad_available = ATOMIC_INIT(1);static struct pardevice *pprt; -static int lcd_initialized;static int keypad_initialized; -static int light_tempo; - -static char lcd_must_clear; -static char lcd_left_shift;static char init_in_progress;static void (*lcd_write_cmd)(int );
@@ -883,23 +890,23 @@ static void lcd_write_data_tilcd(int data)static void lcd_gotoxy (void ) {lcd_write_cmd (0x80 /* set DDRAM address */ - | (lcd_addr_y ? lcd.hwidth :0 ) + | (lcd.addr.y ? lcd.hwidth :0 )/* we force the cursor to stay at the end of the line if it wants to go farther */ - | ((lcd_addr_x < lcd.bwidth) ? lcd_addr_x & + | ((lcd.addr.x < lcd.bwidth) ? lcd.addr.x & (lcd.hwidth -1 ) : lcd.bwidth -1 )); }static void lcd_print (char c) { -if (lcd_addr_x < lcd.bwidth) { +if (lcd.addr.x < lcd.bwidth) {if (lcd_char_conv !=NULL ) c = lcd_char_conv[(unsigned char )c];lcd_write_data (c); - lcd_addr_x++; + lcd.addr.x++; }/* prevents the cursor from wrapping onto the next line */ -if (lcd_addr_x == lcd.bwidth) +if (lcd.addr.x == lcd.bwidth)lcd_gotoxy (); }
@@ -908,8 +915,8 @@ static void lcd_clear_fast_s(void) {int pos; - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;lcd_gotoxy ();spin_lock_irq (&pprt_lock);
@@ -921,8 +928,8 @@ static void lcd_clear_fast_s(void) }spin_unlock_irq (&pprt_lock); - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;lcd_gotoxy (); }
@@ -931,8 +938,8 @@ static void lcd_clear_fast_p8(void) {int pos; - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;lcd_gotoxy ();spin_lock_irq (&pprt_lock);
@@ -959,8 +966,8 @@ static void lcd_clear_fast_p8(void) }spin_unlock_irq (&pprt_lock); - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;lcd_gotoxy (); }
@@ -969,8 +976,8 @@ static void lcd_clear_fast_tilcd(void) {int pos; - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;lcd_gotoxy ();spin_lock_irq (&pprt_lock);
@@ -982,8 +989,8 @@ static void lcd_clear_fast_tilcd(void)spin_unlock_irq (&pprt_lock); - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;lcd_gotoxy (); }
@@ -991,15 +998,15 @@ static void lcd_clear_fast_tilcd(void)static void lcd_clear_display (void ) {lcd_write_cmd (0x01 );/* clear display */ - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;/* we must wait a few milliseconds (15) */ long_sleep (15 ); }static void lcd_init_display (void ) { - lcd_flags = ((lcd.height >1 ) ?LCD_FLAG_N :0 ) + lcd.flags = ((lcd.height >1 ) ?LCD_FLAG_N :0 ) |LCD_FLAG_D |LCD_FLAG_C |LCD_FLAG_B ;long_sleep (20 );/* wait 20 ms after power-up for the paranoid */
@@ -1012,8 +1019,8 @@ static void lcd_init_display(void)long_sleep (10 );lcd_write_cmd (0x30 /* set font height and lines number */ - | ((lcd_flags &LCD_FLAG_F ) ?4 :0 ) - | ((lcd_flags &LCD_FLAG_N ) ?8 :0 ) + | ((lcd.flags &LCD_FLAG_F ) ?4 :0 ) + | ((lcd.flags &LCD_FLAG_N ) ?8 :0 ) );long_sleep (10 );
@@ -1021,12 +1028,12 @@ static void lcd_init_display(void)long_sleep (10 );lcd_write_cmd (0x08 /* set display mode */ - | ((lcd_flags &LCD_FLAG_D ) ?4 :0 ) - | ((lcd_flags &LCD_FLAG_C ) ?2 :0 ) - | ((lcd_flags &LCD_FLAG_B ) ?1 :0 ) + | ((lcd.flags &LCD_FLAG_D ) ?4 :0 ) + | ((lcd.flags &LCD_FLAG_C ) ?2 :0 ) + | ((lcd.flags &LCD_FLAG_B ) ?1 :0 ) ); -lcd_backlight ((lcd_flags &LCD_FLAG_L ) ?1 :0 ); +lcd_backlight ((lcd.flags &LCD_FLAG_L ) ?1 :0 );long_sleep (10 );
@@ -1049,100 +1056,101 @@ static inline int handle_lcd_special_code(void)int processed =0 ; -char *esc = lcd_escape +2 ; -int oldflags = lcd_flags; +char *esc = lcd.esc_seq.buf +2 ; +int oldflags = lcd.flags;/* check for display mode flags */ switch (*esc) {case 'D' :/* Display ON */ - lcd_flags |=LCD_FLAG_D ; + lcd.flags |=LCD_FLAG_D ; processed =1 ;break ;case 'd' :/* Display OFF */ - lcd_flags &= ~LCD_FLAG_D ; + lcd.flags &= ~LCD_FLAG_D ; processed =1 ;break ;case 'C' :/* Cursor ON */ - lcd_flags |=LCD_FLAG_C ; + lcd.flags |=LCD_FLAG_C ; processed =1 ;break ;case 'c' :/* Cursor OFF */ - lcd_flags &= ~LCD_FLAG_C ; + lcd.flags &= ~LCD_FLAG_C ; processed =1 ;break ;case 'B' :/* Blink ON */ - lcd_flags |=LCD_FLAG_B ; + lcd.flags |=LCD_FLAG_B ; processed =1 ;break ;case 'b' :/* Blink OFF */ - lcd_flags &= ~LCD_FLAG_B ; + lcd.flags &= ~LCD_FLAG_B ; processed =1 ;break ;case '+' :/* Back light ON */ - lcd_flags |=LCD_FLAG_L ; + lcd.flags |=LCD_FLAG_L ; processed =1 ;break ;case '-' :/* Back light OFF */ - lcd_flags &= ~LCD_FLAG_L ; + lcd.flags &= ~LCD_FLAG_L ; processed =1 ;break ;case '*' :/* flash back light using the keypad timer */ if (scan_timer.function !=NULL ) { -if (light_tempo ==0 && ((lcd_flags &LCD_FLAG_L ) ==0 )) +if (lcd.light_tempo ==0 + && ((lcd.flags &LCD_FLAG_L ) ==0 ))lcd_backlight (1 ); - light_tempo =FLASH_LIGHT_TEMPO ; + lcd.light_tempo =FLASH_LIGHT_TEMPO ; } processed =1 ;break ;case 'f' :/* Small Font */ - lcd_flags &= ~LCD_FLAG_F ; + lcd.flags &= ~LCD_FLAG_F ; processed =1 ;break ;case 'F' :/* Large Font */ - lcd_flags |=LCD_FLAG_F ; + lcd.flags |=LCD_FLAG_F ; processed =1 ;break ;case 'n' :/* One Line */ - lcd_flags &= ~LCD_FLAG_N ; + lcd.flags &= ~LCD_FLAG_N ; processed =1 ;break ;case 'N' :/* Two Lines */ - lcd_flags |=LCD_FLAG_N ; + lcd.flags |=LCD_FLAG_N ;break ;case 'l' :/* Shift Cursor Left */ -if (lcd_addr_x >0 ) { +if (lcd.addr.x >0 ) {/* back one char if not at end of line */ -if (lcd_addr_x < lcd.bwidth) +if (lcd.addr.x < lcd.bwidth)lcd_write_cmd (0x10 ); - lcd_addr_x--; + lcd.addr.x--; } processed =1 ;break ;case 'r' :/* shift cursor right */ -if (lcd_addr_x < lcd.width) { +if (lcd.addr.x < lcd.width) {/* allow the cursor to pass the end of the line */ -if (lcd_addr_x < +if (lcd.addr.x < (lcd.bwidth -1 ))lcd_write_cmd (0x14 ); - lcd_addr_x++; + lcd.addr.x++; } processed =1 ;break ;case 'L' :/* shift display left */ - lcd_left_shift++; + lcd.left_shift++;lcd_write_cmd (0x18 ); processed =1 ;break ;case 'R' :/* shift display right */ - lcd_left_shift--; + lcd.left_shift--;lcd_write_cmd (0x1C ); processed =1 ;break ;case 'k' : {/* kill end of line */ int x; -for (x = lcd_addr_x; x < lcd.bwidth; x++) +for (x = lcd.addr.x; x < lcd.bwidth; x++)lcd_write_data (' ' );/* restore cursor position */
@@ -1152,7 +1160,7 @@ static inline int handle_lcd_special_code(void) }case 'I' :/* reinitialize display */ lcd_init_display (); - lcd_left_shift =0 ; + lcd.left_shift =0 ; processed =1 ;break ;case 'G' : {
@@ -1223,11 +1231,11 @@ static inline int handle_lcd_special_code(void)while (*esc) {if (*esc =='x' ) { esc++; -if (kstrtoul (esc,10 , &lcd_addr_x) <0 ) +if (kstrtoul (esc,10 , &lcd.addr.x) <0 )break ; }else if (*esc =='y' ) { esc++; -if (kstrtoul (esc,10 , &lcd_addr_y) <0 ) +if (kstrtoul (esc,10 , &lcd.addr.y) <0 )break ; }else {break ;
@@ -1240,25 +1248,25 @@ static inline int handle_lcd_special_code(void) }/* Check whether one flag was changed */ -if (oldflags != lcd_flags) { +if (oldflags != lcd.flags) {/* check whether one of B,C,D flags were changed */ -if ((oldflags ^ lcd_flags) & +if ((oldflags ^ lcd.flags) & (LCD_FLAG_B |LCD_FLAG_C |LCD_FLAG_D ))/* set display mode */ lcd_write_cmd (0x08 - | ((lcd_flags &LCD_FLAG_D ) ?4 :0 ) - | ((lcd_flags &LCD_FLAG_C ) ?2 :0 ) - | ((lcd_flags &LCD_FLAG_B ) ?1 :0 )); + | ((lcd.flags &LCD_FLAG_D ) ?4 :0 ) + | ((lcd.flags &LCD_FLAG_C ) ?2 :0 ) + | ((lcd.flags &LCD_FLAG_B ) ?1 :0 ));/* check whether one of F,N flags was changed */ -else if ((oldflags ^ lcd_flags) & (LCD_FLAG_F |LCD_FLAG_N )) +else if ((oldflags ^ lcd.flags) & (LCD_FLAG_F |LCD_FLAG_N ))lcd_write_cmd (0x30 - | ((lcd_flags &LCD_FLAG_F ) ?4 :0 ) - | ((lcd_flags &LCD_FLAG_N ) ?8 :0 )); + | ((lcd.flags &LCD_FLAG_F ) ?4 :0 ) + | ((lcd.flags &LCD_FLAG_N ) ?8 :0 ));/* check whether L flag was changed */ -else if ((oldflags ^ lcd_flags) & (LCD_FLAG_L )) { -if (lcd_flags & (LCD_FLAG_L )) +else if ((oldflags ^ lcd.flags) & (LCD_FLAG_L )) { +if (lcd.flags & (LCD_FLAG_L ))lcd_backlight (1 ); -else if (light_tempo ==0 ) +else if (lcd.light_tempo ==0 )/* switch off the light only when the tempo lighting is gone */ lcd_backlight (0 );
@@ -1271,29 +1279,29 @@ static inline int handle_lcd_special_code(void)static void lcd_write_char (char c) {/* first, we'll test if we're in escape mode */ -if ((c !='\n' ) && lcd_escape_len >=0 ) { +if ((c !='\n' ) && lcd.esc_seq.len >=0 ) {/* yes, let's add this char to the buffer */ - lcd_escape[lcd_escape_len++] = c; - lcd_escape[lcd_escape_len] =0 ; + lcd.esc_seq.buf[lcd.esc_seq.len++] = c; + lcd.esc_seq.buf[lcd.esc_seq.len] =0 ; }else {/* aborts any previous escape sequence */ - lcd_escape_len =-1 ; + lcd.esc_seq.len =-1 ;switch (c) {case LCD_ESCAPE_CHAR :/* start of an escape sequence */ - lcd_escape_len =0 ; - lcd_escape[lcd_escape_len] =0 ; + lcd.esc_seq.len =0 ; + lcd.esc_seq.buf[lcd.esc_seq.len] =0 ;break ;case '\b' :/* go back one char and clear it */ -if (lcd_addr_x >0 ) { +if (lcd.addr.x >0 ) {/* check if we're not at the end of the line */ -if (lcd_addr_x < lcd.bwidth) +if (lcd.addr.x < lcd.bwidth)/* back one char */ lcd_write_cmd (0x10 ); - lcd_addr_x--; + lcd.addr.x--; }/* replace with a space */ lcd_write_data (' ' );
@@ -1307,15 +1315,15 @@ static void lcd_write_char(char c)case '\n' :/* flush the remainder of the current line and go to the beginning of the next line */ -for (; lcd_addr_x < lcd.bwidth; lcd_addr_x++) +for (; lcd.addr.x < lcd.bwidth; lcd.addr.x++)lcd_write_data (' ' ); - lcd_addr_x =0 ; - lcd_addr_y = (lcd_addr_y +1 ) % lcd.height; + lcd.addr.x =0 ; + lcd.addr.y = (lcd.addr.y +1 ) % lcd.height;lcd_gotoxy ();break ;case '\r' :/* go to the beginning of the same line */ - lcd_addr_x =0 ; + lcd.addr.x =0 ;lcd_gotoxy ();break ;case '\t' :
@@ -1331,32 +1339,32 @@ static void lcd_write_char(char c)/* now we'll see if we're in an escape mode and if the current escape sequence can be understood. */ -if (lcd_escape_len >=2 ) { +if (lcd.esc_seq.len >=2 ) {int processed =0 ; -if (!strcmp (lcd_escape,"[2J" )) { +if (!strcmp (lcd.esc_seq.buf,"[2J" )) {/* clear the display */ lcd_clear_fast (); processed =1 ; - }else if (!strcmp (lcd_escape,"[H" )) { + }else if (!strcmp (lcd.esc_seq.buf,"[H" )) {/* cursor to home */ - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;lcd_gotoxy (); processed =1 ; }/* codes starting with ^[[L */ -else if ((lcd_escape_len >=3 ) && - (lcd_escape[0 ] =='[' ) && - (lcd_escape[1 ] =='L' )) { +else if ((lcd.esc_seq.len >=3 ) && + (lcd.esc_seq.buf[0 ] =='[' ) && + (lcd.esc_seq.buf[1 ] =='L' )) { processed =handle_lcd_special_code (); }/* LCD special escape codes */ /* flush the escape sequence if it's been processed or if it is getting too long. */ -if (processed || (lcd_escape_len >=LCD_ESCAPE_LEN )) - lcd_escape_len =-1 ; +if (processed || (lcd.esc_seq.len >=LCD_ESCAPE_LEN )) + lcd.esc_seq.len =-1 ; }/* escape codes */ }
@@ -1389,9 +1397,9 @@ static int lcd_open(struct inode *inode, struct file *file)if (file->f_mode &FMODE_READ )/* device is write-only */ return -EPERM ; -if (lcd_must_clear) { +if (lcd.must_clear) {lcd_clear_display (); - lcd_must_clear =0 ; + lcd.must_clear = false; }return nonseekable_open (inode, file); }
@@ -1421,7 +1429,7 @@ static void panel_lcd_print(const char *s)const char *tmp = s;int count =strlen (s); -if (lcd.enabled && lcd_initialized) { +if (lcd.enabled && lcd.initialized) {for (; count-- >0 ; tmp++) {if (!in_interrupt () && (((count +1 ) &0x1f ) ==0 ))/* let's be a little nice with other processes
@@ -1602,7 +1610,7 @@ static void lcd_init(void)/* before this line, we must NOT send anything to the display. * Since lcd_init_display() needs to write data, we have to * enable mark the LCD initialized just before. */ - lcd_initialized =1 ; + lcd.initialized = true;lcd_init_display ();/* display a short message */
@@ -1614,10 +1622,10 @@ static void lcd_init(void)panel_lcd_print ("\x1b[Lc\x1b[Lb\x1b[L*Linux-" UTS_RELEASE "\nPanel-" PANEL_VERSION );#endif - lcd_addr_x =0 ; - lcd_addr_y =0 ; + lcd.addr.x =0 ; + lcd.addr.y =0 ;/* clear the display on the next device opening */ - lcd_must_clear =1 ; + lcd.must_clear = true;lcd_gotoxy (); }
@@ -1953,14 +1961,16 @@ static void panel_scan_timer(void)panel_process_inputs (); } -if (lcd.enabled && lcd_initialized) { +if (lcd.enabled && lcd.initialized) {if (keypressed) { -if (light_tempo ==0 && ((lcd_flags &LCD_FLAG_L ) ==0 )) +if (lcd.light_tempo ==0 + && ((lcd.flags &LCD_FLAG_L ) ==0 ))lcd_backlight (1 ); - light_tempo =FLASH_LIGHT_TEMPO ; - }else if (light_tempo >0 ) { - light_tempo--; -if (light_tempo ==0 && ((lcd_flags &LCD_FLAG_L ) ==0 )) + lcd.light_tempo =FLASH_LIGHT_TEMPO ; + }else if (lcd.light_tempo >0 ) { + lcd.light_tempo--; +if (lcd.light_tempo ==0 + && ((lcd.flags &LCD_FLAG_L ) ==0 ))lcd_backlight (0 ); } }
@@ -2132,7 +2142,7 @@ static void keypad_init(void)static int panel_notify_sys (struct notifier_block *this,unsigned long code,void *unused) { -if (lcd.enabled && lcd_initialized) { +if (lcd.enabled && lcd.initialized) {switch (code) {case SYS_DOWN : panel_lcd_print
@@ -2225,9 +2235,9 @@ static void panel_detach(struct parport *port) keypad_initialized =0 ; } -if (lcd.enabled && lcd_initialized) { +if (lcd.enabled && lcd.initialized) {misc_deregister (&lcd_dev); - lcd_initialized =0 ; + lcd.initialized = false; }parport_release (pprt);
@@ -2303,6 +2313,9 @@ static int __init panel_init_module(void) lcd.pins.da = lcd_da_pin; lcd.pins.bl = lcd_bl_pin; +/* Leave it for now, just in case */ + lcd.esc_seq.len =-1 ; +/* * Overwrite selection with module param values (both keypad and lcd), * where the deprecated params have lower prio.
@@ -2388,7 +2401,7 @@ static void __exit panel_cleanup_module(void)panel_lcd_print ("\x0cLCD driver " PANEL_VERSION "\nunloaded.\x1b[Lc\x1b[Lb\x1b[L-" );misc_deregister (&lcd_dev); - lcd_initialized =0 ; + lcd.initialized = false; }/* TODO: free all input signals */
Signature · 1 line
2.1.3
Re: [PATCH 9/9] staging: panel: Move LCD-related state into struct lcd
Quoted 5 lines · Mariusz Gorski
Move more or less all LCD-related state into struct lcd in order to get better cohesion; use bool instead of int where it makes sense.
Signed-off-by Mariusz Gorski <[email protected]>