iwlfiwi with Intel Centrino N1000 won't work with power_save
Hi,
I got report from people that on Intel Centrino N1000 wifi won't work after
updating to 3.17.8. I see in that release Fedora maints enabled POWERCAP and
INTEL RAPL. We got working wifi only after disabling powersave via iw dev wlp2s0 set power_save off.
How we can debug this?
lspci above.
02:00.0 Network controller [0280]: Intel Corporation Centrino Wireless- N 1000 [Condor Peak] [8086:0084]
Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN
[8086:1315]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at d1500000 (64-bit, non-prefetchable)
[size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-
,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0800c Data: 4122
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Exit Latency L0s <128ns, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn-
ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 74-e5-0b-ff-ff-cc-
82-24
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
--
-Igor Gnatenko
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 67 lines · Igor Gnatenko
Hi,
I got report from people that on Intel Centrino N1000 wifi won't work after
updating to 3.17.8. I see in that release Fedora maints enabled POWERCAP and
INTEL RAPL. We got working wifi only after disabling powersave viaiw dev wlp2s0 set power_save off.How we can debug this?
lspci above.
02:00.0 Network controller [0280]: Intel Corporation Centrino Wireless- N 1000 [Condor Peak] [8086:0084]
Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN
[8086:1315]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fastQuoted 1 line
TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory atd1500000(64-bit, non-prefetchable)
[size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-
,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address:00000000fee0800cData: 4122
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s
L1,
Exit Latency L0s <128ns, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn-
ChkCap- ChkEn-
Quoted 7 lines
Capabilities: [140 v1] Device Serial Number 74-e5-0b-ff-ff-cc-
82-24
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
--
-Igor Gnatenko
CC linux-pm@
Signature · 1 line
-Igor Gnatenko
Quoted 9 lines · Igor Gnatenko
Quoted 8 lines · Igor Gnatenko
Hi,
I got report from people that on Intel Centrino N1000 wifi won't work after
updating to 3.17.8. I see in that release Fedora maints enabled POWERCAP and
INTEL RAPL. We got working wifi only after disabling powersave viaiw dev wlp2s0 set power_save off.
What kernel version did you have before?
BTW - for this device, power save is supposed to be disabled by default, but I need to check
Quoted 69 lines
Quoted 59 lines
How we can debug this?
lspci above.
02:00.0 Network controller [0280]: Intel Corporation Centrino Wireless- N 1000 [Condor Peak] [8086:0084]
Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN
[8086:1315]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fastQuoted 1 line
TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory atd1500000(64-bit, non-prefetchable)
[size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-
,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address:00000000fee0800cData: 4122
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s
L1,
Exit Latency L0s <128ns, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn-
ChkCap- ChkEn-Quoted 7 lines
Capabilities: [140 v1] Device Serial Number 74-e5-0b-ff-ff-cc-
82-24
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
--
-Igor GnatenkoCC linux-pm@
--
-Igor Gnatenko
Quoted 12 lines · Emmanuel Grumbach
Quoted 9 lines · Igor Gnatenko
Quoted 8 lines · Igor Gnatenko
Hi,
I got report from people that on Intel Centrino N1000 wifi won't work after
updating to 3.17.8. I see in that release Fedora maints enabled POWERCAP and
INTEL RAPL. We got working wifi only after disabling powersave viaiw dev wlp2s0 set power_save off.
Quoted 3 lines
What kernel version did you have before?
BTW - for this device, power save is supposed to be disabled by default, but I need to check
3.17.4
Quoted 69 lines
Quoted 69 lines
Quoted 59 lines
How we can debug this?
lspci above.
02:00.0 Network controller [0280]: Intel Corporation Centrino Wireless- N 1000 [Condor Peak] [8086:0084]
Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN
[8086:1315]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fastQuoted 1 line
TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory atd1500000(64-bit, non-prefetchable)
[size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-
,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address:00000000fee0800cData: 4122
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s
L1,
Exit Latency L0s <128ns, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn-
ChkCap- ChkEn-Quoted 7 lines
Capabilities: [140 v1] Device Serial Number 74-e5-0b-ff-ff-cc-
82-24
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
--
-Igor GnatenkoCC linux-pm@
--
-Igor Gnatenko
Signature · 1 line
-Igor Gnatenko
Quoted 9 lines
Quoted 9 lines
Quoted 8 lines
Quoted 8 lines
Hi,
I got report from people that on Intel Centrino N1000 wifi won't work after
updating to 3.17.8. I see in that release Fedora maints enabled POWERCAP and
INTEL RAPL. We got working wifi only after disabling powersave viaiw dev wlp2s0 set power_save off.
Quoted 4 lines
Quoted 3 lines
What kernel version did you have before?
BTW - for this device, power save is supposed to be disabled by default, but I need to check3.17.4
$ git log --oneline v3.17.4..v3.17.8 -- drivers/net/wireless/iwlwifi/ fb14996 iwlwifi: mvm: check TLV flag before trying to use hotspot firmware commands 4e709ff iwlwifi: mvm: ROC - bug fixes around time events and locking 85ebf94 iwlwifi: pcie: fix prph dump length
none of these are related to the device your are reporting about.
Quoted 74 lines
Quoted 66 lines
Quoted 66 lines
Quoted 66 lines
How we can debug this?
lspci above.
02:00.0 Network controller [0280]: Intel Corporation Centrino Wireless- N 1000 [Condor Peak] [8086:0084]
Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN
[8086:1315]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fastQuoted 1 line
TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory atd1500000(64-bit, non-prefetchable)
[size=8K]
Capabilities: [c8] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-
,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0
PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address:00000000fee0800cData: 4122
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency
L0s
<512ns, L1 unlimited
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq-
AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s
L1,
Exit Latency L0s <128ns, L1 <32us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt-
UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt-
UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn-
ChkCap- ChkEn-Capabilities: [140 v1] Device Serial Number 74-e5-0b-ff-ff-cc-
82-24
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
--
-Igor GnatenkoQuoted 3 lines
Quoted 3 lines
CC linux-pm@
--
-Igor Gnatenko--
-Igor Gnatenko