Skip to contentSkip to conversation

Crystal Cove PMIC based Panel and Backlight Control

RFC Superseded Shobhit Kumar 5 participants 13 messages Jan 21, 2015 – Feb 5, 2015

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

v3 cover Crystal Cove PMIC based Panel and Backlight Control

Hi All
Please find modifed set of patches using regmap interface to accedd the PMIC registers. These patches implement a drm_panel as a platform driver for the mfd_cell device declared in intel_soc_pmic_core.c.

DRM is extended to provide a find panel by name in absence of OF.

Backlight control is pending. For now I am doing Backlight Enable/Disable also during panel/enable as this will at least save power.

Regards
Shobhit

Shobhit Kumar (4):
drm: Add support to find drm_panel by name
mfd: Add a new cell device for panel controlled by crystal cove pmic drm/i915: Add new panel driver based on crystal cove pmic drm/i915: Enable DSI panel enable/disable based on PMIC

 drivers/gpu/drm/drm_panel.c                    |  18 +++
 drivers/gpu/drm/i915/Kconfig                   |  13 ++
 drivers/gpu/drm/i915/Makefile                  |   3 +
 drivers/gpu/drm/i915/intel-panel-crystalcove.c | 160 +++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_dsi.c               |  16 +++
 drivers/gpu/drm/i915/intel_dsi.h               |   6 +
 drivers/mfd/intel_soc_pmic_crc.c               |   3 +
 include/drm/drm_panel.h                        |   3 +
 8 files changed, 222 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel-panel-crystalcove.c
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
#1 lore raw

RFC v3 1/4 drm: Add support to find drm_panel by name

For scenarios where OF is not available, we can use panel identification by name.

---
 drivers/gpu/drm/drm_panel.c | 18 ++++++++++++++++++
 include/drm/drm_panel.h     |  3 +++
 2 files changed, 21 insertions(+)
drivers/gpu/drm/drm_panel.c +18 -0
index 2ef988e..e1cb8cf 100644
@@ -95,6 +95,24 @@ struct drm_panel *of_drm_find_panel(struct device_node *np)
 EXPORT_SYMBOL(of_drm_find_panel);
 #endif
 
+struct drm_panel *drm_find_panel_by_name(const char *name)
+{
+	struct drm_panel *panel;
+
+	mutex_lock(&panel_lock);
+
+	list_for_each_entry(panel, &panel_list, list) {
+		if (strcmp(panel->name, name) == 0) {
+			mutex_unlock(&panel_lock);
+			return panel;
+		}
+	}
+
+	mutex_unlock(&panel_lock);
+	return NULL;
+}
+EXPORT_SYMBOL(drm_find_panel_by_name);
+
 MODULE_AUTHOR("Thierry Reding <[email protected]>");
 MODULE_DESCRIPTION("DRM panel infrastructure");
 MODULE_LICENSE("GPL and additional rights");
include/drm/drm_panel.h +3 -0
index 1fbcc96..1ef9ff3 100644
@@ -74,6 +74,7 @@ struct drm_panel {
 	struct drm_device *drm;
 	struct drm_connector *connector;
 	struct device *dev;
+	char name[NAME_MAX];
 
 	const struct drm_panel_funcs *funcs;
 
@@ -137,4 +138,6 @@ static inline struct drm_panel *of_drm_find_panel(struct device_node *np)
 }
 #endif
 
+struct drm_panel *drm_find_panel_by_name(const char *name);
+
 #endif
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

Re: [RFC v3 1/4] drm: Add support to find drm_panel by name

Quoted 43 lines · Shobhit Kumar

For scenarios where OF is not available, we can use panel identification by name.

---
 drivers/gpu/drm/drm_panel.c | 18 ++++++++++++++++++
 include/drm/drm_panel.h     |  3 +++
 2 files changed, 21 insertions(+)
drivers/gpu/drm/drm_panel.c +18 -0
index 2ef988e..e1cb8cf 100644
@@ -95,6 +95,24 @@ struct drm_panel *of_drm_find_panel(struct device_node *np)
 EXPORT_SYMBOL(of_drm_find_panel);
 #endif
 
+struct drm_panel *drm_find_panel_by_name(const char *name)
+{
+	struct drm_panel *panel;
+
+	mutex_lock(&panel_lock);
+
+	list_for_each_entry(panel, &panel_list, list) {
+		if (strcmp(panel->name, name) == 0) {
+			mutex_unlock(&panel_lock);
+			return panel;
+		}
+	}
+
+	mutex_unlock(&panel_lock);
+	return NULL;
+}
+EXPORT_SYMBOL(drm_find_panel_by_name);
+
 MODULE_AUTHOR("Thierry Reding <[email protected]>");
 MODULE_DESCRIPTION("DRM panel infrastructure");
 MODULE_LICENSE("GPL and additional rights");
include/drm/drm_panel.h +0 -0
index 1fbcc96..1ef9ff3 100644

include/drm/drm_panel.h struct drm_panel { · line 77

Quoted 4 lines
include/drm/drm_panel.h +1 -0
@@ -74,6 +74,7 @@ struct drm_panel {
 	struct drm_device *drm;
 	struct drm_connector *connector;
 	struct device *dev;
+	char name[NAME_MAX];

I thought I had said this before, but I can't find any record, so here goes again: NAME_MAX is a pretty large number and it increases the size of this structure a lot. Why not use dev_name(dev) to do the matching? Or if that doesn't work for some reason, allocate a string of the right size, or use a static one.

Thierry

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#3 lore raw

PATCH 1/1 drm: Add support to find drm_panel by name

In reply to Shobhit Kumar

For scenarios where OF is not available, we can use panel identification by name.

v2: Use const char *name instead of name[NAME_MAX] (Thierry)

---
 drivers/gpu/drm/drm_panel.c | 18 ++++++++++++++++++
 include/drm/drm_panel.h     |  3 +++
 2 files changed, 21 insertions(+)
drivers/gpu/drm/drm_panel.c +18 -0
index 2ef988e..7b4f559 100644
@@ -95,6 +95,24 @@ struct drm_panel *of_drm_find_panel(struct device_node *np)
 EXPORT_SYMBOL(of_drm_find_panel);
 #endif
 
+struct drm_panel *drm_find_panel_by_name(const char *name)
+{
+	struct drm_panel *panel;
+
+	mutex_lock(&panel_lock);
+
+	list_for_each_entry(panel, &panel_list, list) {
+		if (panel->name && strcmp(panel->name, name) == 0) {
+			mutex_unlock(&panel_lock);
+			return panel;
+		}
+	}
+
+	mutex_unlock(&panel_lock);
+	return NULL;
+}
+EXPORT_SYMBOL(drm_find_panel_by_name);
+
 MODULE_AUTHOR("Thierry Reding <[email protected]>");
 MODULE_DESCRIPTION("DRM panel infrastructure");
 MODULE_LICENSE("GPL and additional rights");
include/drm/drm_panel.h +3 -0
index 1fbcc96..43b9004 100644
@@ -74,6 +74,7 @@ struct drm_panel {
 	struct drm_device *drm;
 	struct drm_connector *connector;
 	struct device *dev;
+	const char *name;
 
 	const struct drm_panel_funcs *funcs;
 
@@ -137,4 +138,6 @@ static inline struct drm_panel *of_drm_find_panel(struct device_node *np)
 }
 #endif
 
+struct drm_panel *drm_find_panel_by_name(const char *name);
+
 #endif
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Tested-by on v1 1/1
#4 lore raw

Re: [PATCH] drm: Add support to find drm_panel by name

Task id: 5711 -------------------------------------Summary-------------------------------------
Platform Delta drm-intel-nightly Series Applied

PNV              +1                 282/283              283/283
ILK                 -1              316/319              315/319
SNB                                  322/346              322/346
IVB                 -2              382/384              380/384
BYT                                  296/296              296/296
HSW                                  425/428              425/428
BDW                                  318/333              318/333
-------------------------------------Detailed-------------------------------------
Platform  Test                                drm-intel-nightly          Series Applied
 PNV  igt_gen3_render_linear_blits      CRASH(1, M23)PASS(2, M25M23)      PASS(1, M23)
*ILK  igt_kms_flip_rcs-flip-vs-panning-interruptible      PASS(2, M26)      DMESG_WARN(1, M26)
 IVB  igt_gem_pwrite_pread_snooped-pwrite-blt-cpu_mmap-performance      DMESG_WARN(2, M34)PASS(1, M21)      DMESG_WARN(1, M34)
*IVB  igt_gem_storedw_batches_loop_secure-dispatch      PASS(3, M21M34)      DMESG_WARN(1, M34)

Note: You need to pay more attention to line start with '*'
_______________________________________________
Intel-gfx mailing list [email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#5 lore raw

RFC v3 2/4 mfd: Add a new cell device for panel controlled by crystal cove pmic

In reply to Shobhit Kumar

On BYT-T configuration, panel enable/disable signals are routed through PMIC. Add a cell device for the same.

---
 drivers/mfd/intel_soc_pmic_crc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/mfd/intel_soc_pmic_crc.c +3 -0
index c85e2ec..c8ccc24 100644
@@ -109,6 +109,9 @@ static struct mfd_cell crystal_cove_dev[] = {
 	{
 		.name = "crystal_cove_pmic",
 	},
+	{
+		.name = "crystal_cove_panel",
+	},
 };
 
 static struct regmap_config crystal_cove_regmap_config = {
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
#6 lore raw

Re: [RFC v3 2/4] mfd: Add a new cell device for panel controlled by crystal cove pmic

Quoted 13 lines · Shobhit Kumar

On BYT-T configuration, panel enable/disable signals are routed through PMIC. Add a cell device for the same.

---
 drivers/mfd/intel_soc_pmic_crc.c | 3 +++
 1 file changed, 3 insertions(+)
drivers/mfd/intel_soc_pmic_crc.c +0 -0
index c85e2ec..c8ccc24 100644

drivers/mfd/intel_soc_pmic_crc.c static struct mfd_cell crystal_cove_dev[] = { · line 117

Quoted 9 lines
drivers/mfd/intel_soc_pmic_crc.c +3 -0
@@ -109,6 +109,9 @@ static struct mfd_cell crystal_cove_dev[] = {
 	{
 		.name = "crystal_cove_pmic",
 	},
+	{
+		.name = "crystal_cove_panel",
+	},
 };
 
 static struct regmap_config crystal_cove_regmap_config = {

This doesn't look at all right. A PMIC doesn't typically contain a panel so this likely is a wrong description of the hardware. Is the datasheet for the Crystal Cove PMIC available somewhere? Google doesn't turn any- thing useful up.

Thierry

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#7 lore raw

Re: [RFC v3 2/4] mfd: Add a new cell device for panel controlled by crystal cove pmic

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 16 lines · Thierry Reding
Quoted 15 lines · Shobhit Kumar

On BYT-T configuration, panel enable/disable signals are routed through PMIC. Add a cell device for the same.

drivers/mfd/intel_soc_pmic_crc.c | 3 +++ 1 file changed, 3 insertions(+)

(quoted diff) +0 -0

b/drivers/mfd/intel_soc_pmic_crc.c index c85e2ec..c8ccc24 100644 --- a/drivers/mfd/intel_soc_pmic_crc.c +++ b/drivers/mfd/intel_soc_pmic_crc.c @@ -109,6 +109,9 @@ static struct mfd_cell crystal_cove_dev[] = { { .name =
"crystal_cove_pmic", }, + { + .name = "crystal_cove_panel", +
}, };

Quoted 6 lines
Quoted 1 line

static struct regmap_config crystal_cove_regmap_config = {

This doesn't look at all right. A PMIC doesn't typically contain a panel so this likely is a wrong description of the hardware. Is the datasheet for the Crystal Cove PMIC available somewhere? Google doesn't turn any- thing useful up.

Perhaps the naming makes it look like wrong, but only the Panel En/Disable and Back light En/Disable/Control signals for any DSI panels on this platform are routed through PMIC. Not sure if any spec is available publicly.

Regards
Shobhit

Quoted 9 lines

Thierry

_______________________________________________ dri-devel mailing list [email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1

iQEcBAEBAgAGBQJU0bU7AAoJEHuQFv2//5KqGh8H/jbr2hjyhW8/omPC+vEgDHTr f8Vh8bsgtEW8YQ89YVJJ8vvioBuhBvRDx8KrxS2122Om0KS4dlEgLBICELWy2Kaw Lf25QfZlZ9+a/OeksJSL6uhwvOwDipUaUGTVSZCZHrUlCk+8YvkFqAEqB/Xv4d5Q 3vUr7OqzTp4hk1BNrZFoXNtal41EPvN8EGcnj/Zixfph1RQhJhpvxexpds2Aznz2 SEH5huOosuGI/rjfch89hvr6yI0UWhzi6i77e5/sN0QkCa07+0imNNDUx53IXmj4 2nXaPvf7myL8WuITYQ5Bj0DNgFkn+TgR1/2THNv3IQHqiofn3bBvsdQBR+5ttzY= =reVa
-----END PGP SIGNATURE-----
_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

#8 lore raw

RFC v3 3/4 drm/i915: Add new panel driver based on crystal cove pmic

In reply to Shobhit Kumar

This driver provides support for the "crystal_cove_panel" cell device. On BYT-T pmic has to be used to enable/disable panel.

v2: Addressed Jani's comments
- Moved inside i915
- Correct licensing
- Remove unused stuff
- Do not initialize prepare/unprepare as they are not needed as of now
- Correct backlight off delay

---
 drivers/gpu/drm/i915/Kconfig                   |  12 ++
 drivers/gpu/drm/i915/Makefile                  |   3 +
 drivers/gpu/drm/i915/intel-panel-crystalcove.c | 159 +++++++++++++++++++++++++
 3 files changed, 174 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel-panel-crystalcove.c
drivers/gpu/drm/i915/Kconfig +12 -0
index 4e39ab3..0510ef0 100644
@@ -69,3 +69,15 @@ config DRM_I915_PRELIMINARY_HW_SUPPORT
 	  option changes the default for that module option.
 
 	  If in doubt, say "N".
+
+config DRM_I915_PANEL_CRYSTALCOVE_PMIC
+	bool "Enable drm panel for crystal cove pmic based control"
+	depends on DRM_I915
+	depends on DRM_PANEL
+	default n
+	help
+	  Choose this option if you have BYT-T based device with DSI panel. On
+	  BYT-T there a crystal cove PMIC which controls the PANEL EN/DISABLE
+	  signals.
+
+	  If in doubt, say "N".
drivers/gpu/drm/i915/Makefile +3 -0
index 1849ffa..cc2f10d 100644
@@ -88,4 +88,7 @@ i915-y += i915_dma.o \
 
 obj-$(CONFIG_DRM_I915)  += i915.o
 
+# I915 DRM Panels
+obj-$(CONFIG_DRM_I915_PANEL_CRYSTALCOVE_PMIC)	+= intel-panel-crystalcove.o
+
 CFLAGS_i915_trace_points.o := -I$(src)
drivers/gpu/drm/i915/intel-panel-crystalcove.c new file +159 -0

159 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
#9 lore raw

Re: [RFC v3 3/4] drm/i915: Add new panel driver based on crystal cove pmic

Quoted 23 lines · Shobhit Kumar

This driver provides support for the "crystal_cove_panel" cell device. On BYT-T pmic has to be used to enable/disable panel.

v2: Addressed Jani's comments
- Moved inside i915
- Correct licensing
- Remove unused stuff
- Do not initialize prepare/unprepare as they are not needed as of now
- Correct backlight off delay

---
 drivers/gpu/drm/i915/Kconfig                   |  12 ++
 drivers/gpu/drm/i915/Makefile                  |   3 +
 drivers/gpu/drm/i915/intel-panel-crystalcove.c | 159 +++++++++++++++++++++++++
 3 files changed, 174 insertions(+)
 create mode 100644 drivers/gpu/drm/i915/intel-panel-crystalcove.c
drivers/gpu/drm/i915/Kconfig +0 -0
index 4e39ab3..0510ef0 100644

drivers/gpu/drm/i915/Kconfig config DRM_I915_PRELIMINARY_HW_SUPPORT · line 77

Quoted 9 lines
drivers/gpu/drm/i915/Kconfig +6 -0
@@ -69,3 +69,15 @@ config DRM_I915_PRELIMINARY_HW_SUPPORT
 	  option changes the default for that module option.
 
 	  If in doubt, say "N".
+
+config DRM_I915_PANEL_CRYSTALCOVE_PMIC
+	bool "Enable drm panel for crystal cove pmic based control"
+	depends on DRM_I915
+	depends on DRM_PANEL
+	default n

n is the default default.

Quoted 1 line
drivers/gpu/drm/i915/intel-panel-crystalcove.c +0 -0

[...]

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 37

Quoted 4 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +4 -0
+#define PMIC_PANEL_EN		0x52
+#define PMIC_PWM_EN		0x51
+#define PMIC_BKL_EN		0x4B
+#define PMIC_PWM_LEVEL		0x4E

These look like they should be GPIOs/regulators and a PWM instead. So I think you'd need to further split up the MFD device to accomodate for this.

Quoted 1 line

+static inline struct crystalcove_panel *to_crystalcove_panel(struct drm_panel *panel)

Please wrap this so it doesn't cross the 80-character boundary.

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 62

Quoted 11 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +11 -0
+static int crystalcove_panel_disable(struct drm_panel *panel)
+{
+	struct crystalcove_panel *p = to_crystalcove_panel(panel);
+
+	if (!p->enabled)
+		return 0;
+
+	DRM_DEBUG_KMS("\n");
+
+	/* invoke the pmic driver */
+	regmap_write(p->regmap, PMIC_PANEL_EN, 0x00);

A datasheet would be really good to determine whether this is the correct place to write this. There are ->prepare() and ->unprepare() callbacks that get the panel into a state where you can communicate with it. This being a DSI panel I would assume that you need to enable the panel to some degree so you can send DSI commands. So most likely this enable "GPIO" should be set in ->unprepare().

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 85

Quoted 11 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +11 -0
+static int crystalcove_panel_enable(struct drm_panel *panel)
+{
+	struct crystalcove_panel *p = to_crystalcove_panel(panel);
+
+	if (p->enabled)
+		return 0;
+
+	DRM_DEBUG_KMS("\n");
+
+	/* invoke the pmic driver */
+	regmap_write(p->regmap, PMIC_PANEL_EN, 0x01);

Similarly I'd expect this to go into ->prepare() to make sure that you can communicate with the panel after ->prepare().

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 88

Quoted 2 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +2 -0
+	/* Enable BKL as well */
+	regmap_write(p->regmap, PMIC_BKL_EN, 0xFF);

Writing 0xff to an "enable" register seems weird. Again the datasheet would help in determining the right thing to do here.

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 91

Quoted 3 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +3 -0
+	regmap_write(p->regmap, PMIC_PWM_EN, 0x01);
+	msleep(20);
+	regmap_write(p->regmap, PMIC_PWM_LEVEL, 255);

This definitely looks like it should be a PWM driver. Also how do you handle backlight brightness control? You only set things to either full off or full on in this driver.

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 128

Quoted 6 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +6 -0
+
+	drm_panel_init(&panel->base);
+	panel->base.dev = dev;
+	panel->base.funcs = &crystalcove_panel_funcs;
+
+	drm_panel_add(&panel->base);

This function can theoretically fail, although it doesn't (at present), so checking the error might be a good idea.

Quoted 13 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +13 -0
+static int crystalcove_panel_remove(struct platform_device *pdev)
+{
+	struct crystalcove_panel *panel = platform_get_drvdata(pdev);
+
+	DRM_DEBUG_KMS("\n");
+
+	drm_panel_detach(&panel->base);
+	drm_panel_remove(&panel->base);
+
+	crystalcove_panel_disable(&panel->base);
+
+	return 0;
+}

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 155

Quoted 10 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +10 -0
+
+static struct platform_driver crystalcove_panel_driver = {
+	.probe = crystalcove_panel_probe,
+	.remove = crystalcove_panel_remove,
+	.driver = {
+		.name = "crystal_cove_panel",
+	},
+};
+
+module_platform_driver(crystalcove_panel_driver);

What's also weird here is that you claim this to be a DSI panel, yet you use a platform driver. The right thing to do would be to instantiate the device as mipi_dsi_device, with the DSI controller being the parent.

Thierry

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#10 lore raw

Re: [RFC v3 3/4] drm/i915: Add new panel driver based on crystal cove pmic

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Quoted 24 lines · Thierry Reding
Quoted 23 lines · Shobhit Kumar

This driver provides support for the "crystal_cove_panel" cell device. On BYT-T pmic has to be used to enable/disable panel.

v2: Addressed Jani's comments - Moved inside i915 - Correct licensing - Remove unused stuff - Do not initialize prepare/unprepare as they are not needed as of now - Correct backlight off delay

drivers/gpu/drm/i915/Kconfig                   |  12 ++ 
drivers/gpu/drm/i915/Makefile                  |   3 + 
drivers/gpu/drm/i915/intel-panel-crystalcove.c | 159

+++++++++++++++++++++++++ 3 files changed, 174 insertions(+) create mode 100644 drivers/gpu/drm/i915/intel-panel-crystalcove.c

(quoted diff) +0 -0

b/drivers/gpu/drm/i915/Kconfig index 4e39ab3..0510ef0 100644 --- a/drivers/gpu/drm/i915/Kconfig +++ b/drivers/gpu/drm/i915/Kconfig @@ -69,3 +69,15 @@ config DRM_I915_PRELIMINARY_HW_SUPPORT option changes the default for that module option.

Quoted 5 lines
Quoted 3 lines

If in doubt, say "N". + +config DRM_I915_PANEL_CRYSTALCOVE_PMIC + bool "Enable drm panel for crystal cove pmic based control" +
depends on DRM_I915 + depends on DRM_PANEL + default n

n is the default default.

Okay.

Quoted 10 lines
Quoted 3 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +0 -0

[...]

Quoted 2 lines

+#define PMIC_PANEL_EN 0x52 +#define PMIC_PWM_EN 0x51 +#define
PMIC_BKL_EN 0x4B +#define PMIC_PWM_LEVEL 0x4E

These look like they should be GPIOs/regulators and a PWM instead. So I think you'd need to further split up the MFD device to accomodate for this.

Yes these are I2C addresses for the PWM and Panel control registers on PMIC. The PMIC driver is a I2C slave device and all control for Crystal cove is through i2c. Till now there is no situation where either of the two PWM and Panel control are through interfaces other than PMIC. Either both are through PMIC or none. With that in mind, I think can have one common MFD device for PWM and Panel control. Also I was planning to add Backlight control via backlight class driver in this same panel driver.

Quoted 6 lines
Quoted 3 lines

+static inline struct crystalcove_panel
*to_crystalcove_panel(struct drm_panel *panel)

Please wrap this so it doesn't cross the 80-character boundary.

Quoted 13 lines
Quoted 5 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +3 -0
+static int crystalcove_panel_disable(struct drm_panel *panel) 
+{ +	struct crystalcove_panel *p = to_crystalcove_panel(panel); 
+ +	if (!p->enabled) +		return 0; + +	DRM_DEBUG_KMS("\n"); + +	/*

invoke the pmic driver */ + regmap_write(p->regmap,
PMIC_PANEL_EN, 0x00);

A datasheet would be really good to determine whether this is the correct place to write this. There are ->prepare() and ->unprepare() callbacks that get the panel into a state where you can communicate with it. This being a DSI panel I would assume that you need to enable the panel to some degree so you can send DSI commands. So most likely this enable "GPIO" should be set in ->unprepare().

This is just a mechanism to enable needed signals which are routed through PMIC, I kept the logic as per enable and disable signals in enable/disable. But yes actually it is preparing the panel to receive DCS commands. I can move this into prepare/unprepare. In that case there would be no need for any enable/disable callbacks.

Quoted 9 lines
Quoted 6 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +2 -0
+static int crystalcove_panel_enable(struct drm_panel *panel) +{ 
+	struct crystalcove_panel *p = to_crystalcove_panel(panel); + +

if (p->enabled) + return 0; + + DRM_DEBUG_KMS("\n"); + + /*
invoke the pmic driver */ + regmap_write(p->regmap,
PMIC_PANEL_EN, 0x01);

Similarly I'd expect this to go into ->prepare() to make sure that you can communicate with the panel after ->prepare().

Can do as I mentioned above.

Quoted 6 lines
Quoted 3 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +1 -0
+	/* Enable BKL as well */ +	regmap_write(p->regmap, PMIC_BKL_EN,

0xFF);

Writing 0xff to an "enable" register seems weird. Again the datasheet would help in determining the right thing to do here.

Actually, I think I made a mistake in naming the register. It is actually the PWMCLKDIV which has to be programmed as per needed divider. I will correct this. Spec is not available in public.

Quoted 7 lines
Quoted 3 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +1 -0
+	regmap_write(p->regmap, PMIC_PWM_EN, 0x01); +	msleep(20); +

regmap_write(p->regmap, PMIC_PWM_LEVEL, 255);

This definitely looks like it should be a PWM driver. Also how do you handle backlight brightness control? You only set things to either full off or full on in this driver.

As of now I did just enable and disable to save power leakage during Suspend/Resume. I am planning to add a backlight class driver as well as pert of this itself. As I said this should be okay as either both Panel and PWM control is thorough PMIC or none in our platforms as of now.

Quoted 7 lines
Quoted 4 lines

+ + drm_panel_init(&panel->base); + panel->base.dev = dev; +
panel->base.funcs = &crystalcove_panel_funcs; + +
drm_panel_add(&panel->base);

This function can theoretically fail, although it doesn't (at present), so checking the error might be a good idea.

Okay.

Quoted 17 lines
Quoted 12 lines

+static int crystalcove_panel_remove(struct platform_device
*pdev) +{ + struct crystalcove_panel *panel =
platform_get_drvdata(pdev); + + DRM_DEBUG_KMS("\n"); + +
drm_panel_detach(&panel->base); + drm_panel_remove(&panel->base); + +
crystalcove_panel_disable(&panel->base); + + return 0; +} +
+static struct platform_driver crystalcove_panel_driver = { +
.probe = crystalcove_panel_probe, + .remove =
crystalcove_panel_remove, + .driver = { + .name =
"crystal_cove_panel", + }, +}; +
+module_platform_driver(crystalcove_panel_driver);

What's also weird here is that you claim this to be a DSI panel, yet you use a platform driver. The right thing to do would be to instantiate the device as mipi_dsi_device, with the DSI controller being the parent.

This is not a DSI panel driver but just to control the Panel EN/Disbale signals and PWM on BYT platform with CRC PMIC. mipi_dsi_device conversion for the actual DSI panel driver is recently done on i915.

Regards
Shobhit

Quoted 9 lines

Thierry

_______________________________________________ dri-devel mailing list [email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1

iQEcBAEBAgAGBQJU0cJJAAoJEHuQFv2//5KqjBkH/35Md/V3bpdNzA0+hjrTy7ap GPbApTUhyurYm32jAqQwtoVsYHl4Wysyv8lTxQnz+j1VcvWcq2e3a25j1Qo0ybbq dZeDTr2r3X7Fgj+arFboLxEQSvIWLaT0ML+xaNorbsCaEGxXl/frX/fTCuWXeJet VX1dII9UbTKtxV/Sc1lcXruL9O4pJSnH02tP+sXqev1gyPhm8EU2Wjz3MReUsvVh roWnaYTUk7GS15ihuvD2mbm4+o5H8GD8wEP2F5telcKoD4C49HKFbmWVyXFKjHSe kojntvgYAUGBQY2g6ytTk+nuE/56e3cIFSr27v8RwffWLw+VOWELT30gtKLF6ww= =Jqac
-----END PGP SIGNATURE-----
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#11 lore raw

Re: [Intel-gfx] [RFC v3 3/4] drm/i915: Add new panel driver based on crystal cove pmic

In reply to Thierry Reding
Quoted 11 lines · Thierry Reding
Quoted 1 line · Shobhit Kumar
drivers/gpu/drm/i915/intel-panel-crystalcove.c +0 -0

[...]

drivers/gpu/drm/i915/intel-panel-crystalcove.c line 37

Quoted 4 lines
drivers/gpu/drm/i915/intel-panel-crystalcove.c +4 -0
+#define PMIC_PANEL_EN		0x52
+#define PMIC_PWM_EN		0x51
+#define PMIC_BKL_EN		0x4B
+#define PMIC_PWM_LEVEL		0x4E

These look like they should be GPIOs/regulators and a PWM instead. So I think you'd need to further split up the MFD device to accomodate for this.

I've had some extension discussion with Thierry on irc and I agree that using gpio/pwm interfaces will suit better. In addition both gpio and pwm subsystem already have magic register/lookup support (which works outside of devicetree or the new acpi tables, which I didn't know). So we'll avoid writing our own inter-module boilerplate.

Shobhit, Jani&I also chatted about this topic on irc and I think the rough direction is hopefully clear now.

Just a quick mail here for the record so that the irc discussion won't get lost.
-Daniel

Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/dri-devel
#12 lore raw

RFC v3 4/4 drm/i915: Enable DSI panel enable/disable based on PMIC

In reply to Shobhit Kumar

This allows for proper PPS during enable/disable of BYT-T platforms where these signals are routed through PMIC. Needs DRM_PANEL to be selected by default as well

v2: Adapt to panel find function name change in drm_panel

---
 drivers/gpu/drm/i915/Kconfig                   |  1 +
 drivers/gpu/drm/i915/intel-panel-crystalcove.c |  1 +
 drivers/gpu/drm/i915/intel_dsi.c               | 16 ++++++++++++++++
 drivers/gpu/drm/i915/intel_dsi.h               |  6 ++++++
 4 files changed, 24 insertions(+)
drivers/gpu/drm/i915/Kconfig +1 -0
index 0510ef0..bacbc06 100644
@@ -18,6 +18,7 @@ config DRM_I915
 	select INPUT if ACPI
 	select ACPI_VIDEO if ACPI
 	select ACPI_BUTTON if ACPI
+	select DRM_PANEL
 	help
 	  Choose this option if you have a system that has "Intel Graphics
 	  Media Accelerator" or "HD Graphics" integrated graphics,
drivers/gpu/drm/i915/intel-panel-crystalcove.c +1 -0
index a6aefa3..0f129b2 100644
@@ -154,6 +154,7 @@ static struct platform_driver crystalcove_panel_driver = {
 
 module_platform_driver(crystalcove_panel_driver);
 
+MODULE_ALIAS();
 MODULE_AUTHOR("Shobhit Kumar <[email protected]");
 MODULE_DESCRIPTION("Intel Crystal Cove Panel Driver");
 MODULE_LICENSE("GPL and additional rights");
drivers/gpu/drm/i915/intel_dsi.c +16 -0
index 42b6d6f..6857d19 100644
@@ -26,6 +26,7 @@
 #include <drm/drmP.h>
 #include <drm/drm_crtc.h>
 #include <drm/drm_edid.h>
+#include <drm/drm_panel.h>
 #include <drm/i915_drm.h>
 #include <linux/slab.h>
 #include "i915_drv.h"
@@ -230,6 +231,8 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)
 
 	DRM_DEBUG_KMS("\n");
 
+	drm_panel_enable(intel_dsi->panel);
+
 	/* Disable DPOunit clock gating, can stall pipe
 	 * and we need DPLL REFA always enabled */
 	tmp = I915_READ(DPLL(pipe));
@@ -392,6 +395,8 @@ static void intel_dsi_post_disable(struct intel_encoder *encoder)
 
 	msleep(intel_dsi->panel_off_delay);
 	msleep(intel_dsi->panel_pwr_cycle_delay);
+
+	drm_panel_disable(intel_dsi->panel);
 }
 
 static bool intel_dsi_get_hw_state(struct intel_encoder *encoder,
@@ -896,6 +901,17 @@ void intel_dsi_init(struct drm_device *dev)
 	fixed_mode->type |= DRM_MODE_TYPE_PREFERRED;
 	intel_panel_init(&intel_connector->panel, fixed_mode, NULL);
 
+	/* Initialize the PMIC based drm_panel if available on the platform */
+	if (dev_priv->vbt.dsi.config->pwm_blc == PPS_BLC_PMIC) {
+		intel_dsi->panel = drm_find_panel_by_name("crystal_cove_panel");
+		if (!intel_dsi->panel) {
+			DRM_ERROR("PMIC Panel control will not work !!\n");
+			return;
+		}
+
+		drm_panel_attach(intel_dsi->panel, connector);
+	}
+
 	return;
 
 err:
drivers/gpu/drm/i915/intel_dsi.h +6 -0
index 8fe2064..4a9242d 100644
@@ -33,6 +33,9 @@
 #define DSI_DUAL_LINK_FRONT_BACK	1
 #define DSI_DUAL_LINK_PIXEL_ALT		2
 
+#define PPS_BLC_PMIC	0
+#define PPS_BLC_SOC	1
+
 struct intel_dsi_device {
 	unsigned int panel_id;
 	const char *name;
@@ -83,6 +86,8 @@ struct intel_dsi {
 
 	struct intel_connector *attached_connector;
 
+	struct drm_panel *panel;
+
 	/* bit mask of ports being driven */
 	u16 ports;
 
@@ -116,6 +121,7 @@ struct intel_dsi {
 	u32 dphy_reg;
 	u32 video_frmt_cfg_bits;
 	u16 lp_byte_clk;
+	u8 pps_blc;
 
 	/* timeouts in byte clocks */
 	u16 lp_rx_timeout;
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx