Skip to contentSkip to conversation

sunxi: Add Linksprite_pcDuino3_Nano board / defconfig

PATCH Superseded Adam Sampson 2 participants 2 messages Jan 26, 2015 – Jan 28, 2015 Arm/Allwinner sunXi SoC support

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 sunxi: Add Linksprite_pcDuino3_Nano board / defconfig

This is a low-cost Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM, 4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and another for power in, HDMI, SATA, 5V power for SATA devices, gigabit Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector.

For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano

---
 board/sunxi/MAINTAINERS                    |  5 +++++
 configs/Linksprite_pcDuino3_Nano_defconfig | 11 +++++++++++
 2 files changed, 16 insertions(+)
 create mode 100644 configs/Linksprite_pcDuino3_Nano_defconfig
board/sunxi/MAINTAINERS +5 -0
index 743e7f5..479d147 100644
@@ -100,3 +100,8 @@ MELE M5 BOARD
 M:	Ian Campbell <[email protected]>
 S:	Maintained
 F:	configs/Mele_M5_defconfig
+
+LINKSPRITE-PCDUINO3-NANO BOARD
+M:	Adam Sampson <[email protected]>
+S:	Maintained
+F:	configs/Linksprite_pcDuino3_Nano_defconfig
configs/Linksprite_pcDuino3_Nano_defconfig new file +11 -0
new file mode 100644
index 0000000..e3ea713
@@ -0,0 +1,11 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPH(2),USB_EHCI"
+CONFIG_FDTFILE="sun7i-a20-pcduino3-nano.dtb"
+CONFIG_USB1_VBUS_PIN="PH11"
++S:CONFIG_ARM=y
++S:CONFIG_ARCH_SUNXI=y
++S:CONFIG_MACH_SUN7I=y
++S:CONFIG_TARGET_PCDUINO3_NANO=y
++S:CONFIG_DRAM_CLK=408
++S:CONFIG_DRAM_ZQ=122
++S:CONFIG_DRAM_EMR1=4
Signature · 1 line
2.2.2
#1 lore raw

PATCH v2 1/1 sunxi: Add Linksprite_pcDuino3_Nano board / defconfig

Hi,

Quoted 9 lines · Adam Sampson

This is a low-cost Allwinner A20 board with Arduino-style GPIO headers; it features 1G RAM, 4G NAND flash, 1 micro-SD, 2 USB sockets, 1 micro USB socket for OTG and another for power in, HDMI, SATA, 5V power for SATA devices, gigabit Ethernet, an IR receiver, 3.5mm audio out and a MIPI camera connector.

For more details, see: http://linux-sunxi.org/LinkSprite_pcDuino3_Nano

Thanks I've replaced the original patch in u-boot-sunxi/next with this one.

Regards,

Hans

Quoted 37 lines
---
  board/sunxi/MAINTAINERS                    |  5 +++++
  configs/Linksprite_pcDuino3_Nano_defconfig | 11 +++++++++++
  2 files changed, 16 insertions(+)

create mode 100644 configs/Linksprite_pcDuino3_Nano_defconfig

board/sunxi/MAINTAINERS +5 -0
index 743e7f5..479d147 100644
@@ -100,3 +100,8 @@ MELE M5 BOARD
  M:	Ian Campbell <[email protected]>
  S:	Maintained
  F:	configs/Mele_M5_defconfig
+
+LINKSPRITE-PCDUINO3-NANO BOARD
+M:	Adam Sampson <[email protected]>
+S:	Maintained
+F:	configs/Linksprite_pcDuino3_Nano_defconfig
configs/Linksprite_pcDuino3_Nano_defconfig new file +11 -0
new file mode 100644
index 0000000..e3ea713
@@ -0,0 +1,11 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="AXP209_POWER,SUNXI_GMAC,RGMII,AHCI,SATAPWR=SUNXI_GPH(2),USB_EHCI"
+CONFIG_FDTFILE="sun7i-a20-pcduino3-nano.dtb"
+CONFIG_USB1_VBUS_PIN="PH11"
++S:CONFIG_ARM=y
++S:CONFIG_ARCH_SUNXI=y
++S:CONFIG_MACH_SUN7I=y
++S:CONFIG_TARGET_PCDUINO3_NANO=y
++S:CONFIG_DRAM_CLK=408
++S:CONFIG_DRAM_ZQ=122
++S:CONFIG_DRAM_EMR1=4