Skip to contentSkip to conversation

drivers: input: mouse: Add Foxconn's CNTouch driver

PATCH Superseded Thomas Sanchez 2 participants 10 messages Jan 29, 2015 – Feb 26, 2015

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 drivers: input: mouse: Add Foxconn's CNTouch driver

This commit introduces a new driver for Foxconn CNTouch trackpad that can be found on LDLC's laptop IRIS family. The driver has been inspired from usbmouse.c.

---
 drivers/input/mouse/Kconfig       |  11 ++
 drivers/input/mouse/Makefile      |   1 +
 drivers/input/mouse/foxconn_usb.c | 206 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 218 insertions(+)
 create mode 100644 drivers/input/mouse/foxconn_usb.c
drivers/input/mouse/Kconfig +11 -0
index d8b46b0..3ccb924 100644
@@ -403,4 +403,15 @@ config MOUSE_NAVPOINT_PXA27x
 	  To compile this driver as a module, choose M here: the
 	  module will be called navpoint.
 
+config MOUSE_FOXCONN_CNTOUCH
+	tristate "Foxconn CNTouch USB device support"
+	depends on USB_ARCH_HAS_HCD
+	select USB
+	help
+	  This driver adds support for the Foxconn CNTouch trackpad present for
+	  instance on IRIS laptop family from LDLC.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called foxconn_usb.
+
 endif
drivers/input/mouse/Makefile +1 -0
index 560003d..4bfcc75 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_MOUSE_ATARI)		+= atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)		+= bcm5974.o
 obj-$(CONFIG_MOUSE_CYAPA)		+= cyapa.o
 obj-$(CONFIG_MOUSE_ELAN_I2C)		+= elan_i2c.o
+obj-$(CONFIG_MOUSE_FOXCONN_CNTOUCH)	+= foxconn_usb.o
 obj-$(CONFIG_MOUSE_GPIO)		+= gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)		+= inport.o
 obj-$(CONFIG_MOUSE_LOGIBM)		+= logibm.o
drivers/input/mouse/foxconn_usb.c new file +206 -0

206 lines not on this page · raw message

Signature · 1 line
2.1.0
#1 lore raw

PATCH v2 1/1 drivers: input: mouse: Add Foxconn's CNTouch driver

Of course for my first mail ever on a Linux ML I did a mistake... Here is a patch that actually compiles.

Sorry for the noise.
Please let me know if anything's wrong.

Cheers,

#2 lore raw

PATCH 1/1 drivers: input: mouse: Add Foxconn's CNTouch driver

This commit introduces a new driver for Foxconn CNTouch trackpad that can be found on LDLC's laptop IRIS family. The driver has been inspired from usbmouse.c.

---
 drivers/input/mouse/Kconfig       |  11 ++
 drivers/input/mouse/Makefile      |   1 +
 drivers/input/mouse/foxconn_usb.c | 206 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 218 insertions(+)
 create mode 100644 drivers/input/mouse/foxconn_usb.c
drivers/input/mouse/Kconfig +11 -0
index d8b46b0..3ccb924 100644
@@ -403,4 +403,15 @@ config MOUSE_NAVPOINT_PXA27x
 	  To compile this driver as a module, choose M here: the
 	  module will be called navpoint.
 
+config MOUSE_FOXCONN_CNTOUCH
+	tristate "Foxconn CNTouch USB device support"
+	depends on USB_ARCH_HAS_HCD
+	select USB
+	help
+	  This driver adds support for the Foxconn CNTouch trackpad present for
+	  instance on IRIS laptop family from LDLC.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called foxconn_usb.
+
 endif
drivers/input/mouse/Makefile +1 -0
index 560003d..4bfcc75 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_MOUSE_ATARI)		+= atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)		+= bcm5974.o
 obj-$(CONFIG_MOUSE_CYAPA)		+= cyapa.o
 obj-$(CONFIG_MOUSE_ELAN_I2C)		+= elan_i2c.o
+obj-$(CONFIG_MOUSE_FOXCONN_CNTOUCH)	+= foxconn_usb.o
 obj-$(CONFIG_MOUSE_GPIO)		+= gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)		+= inport.o
 obj-$(CONFIG_MOUSE_LOGIBM)		+= logibm.o
drivers/input/mouse/foxconn_usb.c new file +206 -0

206 lines not on this page · raw message

Signature · 1 line
2.1.0
maintainer
#3 lore raw

Hi Thomas,

Quoted 3 lines · Thomas Sanchez

This commit introduces a new driver for Foxconn CNTouch trackpad that can be found on LDLC's laptop IRIS family. The driver has been inspired from usbmouse.c.

So I guess it does not work as a standard HID device, does it?

drivers/input/mouse/foxconn_usb.c

Quoted 47 lines
---
 drivers/input/mouse/Kconfig       |  11 ++
 drivers/input/mouse/Makefile      |   1 +
 drivers/input/mouse/foxconn_usb.c | 206 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 218 insertions(+)
 create mode 100644 drivers/input/mouse/foxconn_usb.c
drivers/input/mouse/Kconfig +11 -0
index d8b46b0..3ccb924 100644
@@ -403,4 +403,15 @@ config MOUSE_NAVPOINT_PXA27x
 	  To compile this driver as a module, choose M here: the
 	  module will be called navpoint.
 
+config MOUSE_FOXCONN_CNTOUCH
+	tristate "Foxconn CNTouch USB device support"
+	depends on USB_ARCH_HAS_HCD
+	select USB
+	help
+	  This driver adds support for the Foxconn CNTouch trackpad present for
+	  instance on IRIS laptop family from LDLC.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called foxconn_usb.
+
 endif
drivers/input/mouse/Makefile +1 -0
index 560003d..4bfcc75 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_MOUSE_ATARI)		+= atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)		+= bcm5974.o
 obj-$(CONFIG_MOUSE_CYAPA)		+= cyapa.o
 obj-$(CONFIG_MOUSE_ELAN_I2C)		+= elan_i2c.o
+obj-$(CONFIG_MOUSE_FOXCONN_CNTOUCH)	+= foxconn_usb.o
 obj-$(CONFIG_MOUSE_GPIO)		+= gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)		+= inport.o
 obj-$(CONFIG_MOUSE_LOGIBM)		+= logibm.o
drivers/input/mouse/foxconn_usb.c new file +0 -0
new file mode 100644
index 0000000..d05d03e
@@ -0,0 +1,206 @@

It is customary to put copyright notice and license at the beginning of the file.

Quoted 48 lines
drivers/input/mouse/foxconn_usb.c new file +48 -0
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/usb/input.h>
+
+#define USB_VENDOR_ID_FOXCONN		0x294e
+#define USB_DEVICE_ID_FOXCONN_CNTOUCH	0x1001
+
+#define DRIVER_DESC	"CNTouch USB Driver"
+
+static const struct usb_device_id cntouch_devices[] = {
+	{USB_DEVICE(USB_VENDOR_ID_FOXCONN, USB_DEVICE_ID_FOXCONN_CNTOUCH)},
+	{},
+};
+
+MODULE_AUTHOR("Thomas Sanchez, [email protected]");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+
+MODULE_DEVICE_TABLE(usb, cntouch_devices);
+
+struct cntouch_device {
+	struct usb_device *usb_dev;
+	struct input_dev *input_dev;
+	struct urb *irq;
+	signed char *data;
+	dma_addr_t data_dma;
+	char usb_path[64];
+};
+
+static void cntouch_irq(struct urb *urb)
+{
+	struct cntouch_device *cn_dev = urb->context;
+	signed char *data = cn_dev->data;
+	struct input_dev *dev = cn_dev->input_dev;
+	int status;
+
+	switch (urb->status) {
+	case 0:
+		break;
+	case -ECONNRESET:
+	case -ENOENT:
+	case -ESHUTDOWN:
+		return;
+	default:
+		goto resubmit;

drivers/input/mouse/foxconn_usb.c line 58

Quoted 10 lines
drivers/input/mouse/foxconn_usb.c new file +10 -0
+	}
+
+	input_report_key(dev, BTN_LEFT, data[0] & 0x01);
+	input_report_key(dev, BTN_RIGHT, data[0] & 0x02);
+
+	/*
+	 * when scrolling horizontally with two fingers, data[4] is used but I
+	 * did not find the right mapping...
+	 */
+	input_report_key(dev, BTN_TOOL_FINGER, data[4] == 0 ? 1 : 2);

Value of 2 does not make sense to use with input_report_key() as it converts the value into boolean anyway. Also BTN_TOOL_FINGER should be used by trackapds/touchpads working in absolute mode while this device seems to be using relative mode.

By the way, we have REL_HWHEEL event for reporting horizontal scrolling.

Quoted 13 lines
drivers/input/mouse/foxconn_usb.c new file +13 -0
+
+	input_report_rel(dev, REL_X, data[1]);
+	input_report_rel(dev, REL_Y, data[2]);
+
+	input_report_rel(dev, REL_WHEEL, data[3]);
+
+	input_sync(dev);
+
+resubmit:
+	status = usb_submit_urb(urb, GFP_ATOMIC);
+	if (status) {
+		dev_err(&cn_dev->usb_dev->dev,
+			"can't resubmit intr, %s-%s/input0, status %d\n",

drivers/input/mouse/foxconn_usb.c line 81

Quoted 10 lines
drivers/input/mouse/foxconn_usb.c new file +10 -0
+			cn_dev->usb_dev->bus->bus_name,
+			cn_dev->usb_dev->devpath, status);
+	}
+}
+
+static int cntouch_open(struct input_dev *dev)
+{
+	struct cntouch_device *cn_dev = input_get_drvdata(dev);
+
+	cn_dev->irq->dev = cn_dev->usb_dev;

I do not think you need to do this assignment anymore.

Quoted 7 lines
drivers/input/mouse/foxconn_usb.c new file +7 -0
+	if (usb_submit_urb(cn_dev->irq, GFP_KERNEL))
+		return -EIO;
+	return 0;
+}
+
+static void cntouch_close(struct input_dev *dev)
+{

drivers/input/mouse/foxconn_usb.c line 98

Quoted 10 lines
drivers/input/mouse/foxconn_usb.c new file +10 -0
+	struct cntouch_device *cn_dev = input_get_drvdata(dev);
+
+	usb_kill_urb(cn_dev->irq);
+}
+
+static int cntouch_probe(struct usb_interface *interface,
+			 const struct usb_device_id *id)
+{
+	struct usb_device *usb_dev = interface_to_usbdev(interface);
+	struct cntouch_device *cn_dev = NULL;

Please do not initialize variables unless you actually need the initial value. This gives the compiler chance to warn you about "using uninitialized variable" code paths instead of happily using NULL/0/whatever initial value you set and running into problems at runtime.

drivers/input/mouse/foxconn_usb.c line 102

Quoted 4 lines
drivers/input/mouse/foxconn_usb.c new file +4 -0
+	struct usb_host_interface *host_interface;
+	struct usb_endpoint_descriptor *endpoint;
+	int pipe, maxp;
+	int error = -ENOMEM;

Same here.

Quoted 12 lines
drivers/input/mouse/foxconn_usb.c new file +12 -0
+
+	host_interface = interface->cur_altsetting;
+
+	if (host_interface->desc.bNumEndpoints != 1)
+		return -ENODEV;
+
+	endpoint = &host_interface->endpoint[0].desc;
+	if (!usb_endpoint_is_int_in(endpoint))
+		return -ENODEV;
+
+	pipe = usb_rcvintpipe(usb_dev, endpoint->bEndpointAddress);
+	maxp = usb_maxpacket(usb_dev, pipe, usb_pipeout(pipe));

drivers/input/mouse/foxconn_usb.c line 124

Quoted 10 lines
drivers/input/mouse/foxconn_usb.c new file +10 -0
+
+	cn_dev = kzalloc(sizeof(*cn_dev), GFP_KERNEL);
+	if (cn_dev == NULL)
+		goto err_1;
+
+	cn_dev->input_dev = input_allocate_device();
+	if (!cn_dev->input_dev)
+		goto err_2;
+
+	cn_dev->usb_dev = usb_get_dev(usb_dev);

This is not needed: while driver is bound to the device it is not going anywhere.

Quoted 32 lines
drivers/input/mouse/foxconn_usb.c new file +32 -0
+
+	cn_dev->data =
+	    usb_alloc_coherent(usb_dev, 8, GFP_ATOMIC, &cn_dev->data_dma);
+	if (!cn_dev->data)
+		goto err_3;
+
+	cn_dev->irq = usb_alloc_urb(0, GFP_KERNEL);
+	if (!cn_dev->irq)
+		goto err_4;
+
+	usb_set_intfdata(interface, cn_dev);
+
+	usb_make_path(usb_dev, cn_dev->usb_path, sizeof(cn_dev->usb_path));
+	strlcat(cn_dev->usb_path, "/input0", sizeof(cn_dev->usb_path));
+
+	cn_dev->input_dev->name = "CNTouch";
+	cn_dev->input_dev->phys = cn_dev->usb_path;
+	usb_to_input_id(usb_dev, &cn_dev->input_dev->id);
+	cn_dev->input_dev->dev.parent = &interface->dev;
+
+	cn_dev->input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REL);
+	cn_dev->input_dev->keybit[BIT_WORD(BTN_MOUSE)] =
+	    BIT_MASK(BTN_LEFT) | BIT_MASK(BTN_RIGHT);
+	cn_dev->input_dev->relbit[0] =
+	    BIT_MASK(REL_X) | BIT_MASK(REL_Y) | BIT_MASK(REL_WHEEL);
+
+	input_set_drvdata(cn_dev->input_dev, cn_dev);
+
+	cn_dev->input_dev->open = cntouch_open;
+	cn_dev->input_dev->close = cntouch_close;
+
+	usb_fill_int_urb(cn_dev->irq, usb_dev, pipe, cn_dev->data,

drivers/input/mouse/foxconn_usb.c line 166

Quoted 10 lines
drivers/input/mouse/foxconn_usb.c new file +10 -0
+			 (maxp > 8 ? 8 : maxp), cntouch_irq, cn_dev,
+			 endpoint->bInterval);
+	cn_dev->irq->transfer_dma = cn_dev->data_dma;
+	cn_dev->irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+
+	error = input_register_device(cn_dev->input_dev);
+	if (error)
+		goto err_5;
+
+	dev_info(&interface->dev, DRIVER_DESC "device now attached\n");

Please drop this message, we are already noisy enough. Input core will message when new input device is created anyway.

Quoted 4 lines
drivers/input/mouse/foxconn_usb.c new file +4 -0
+	return 0;
+
+err_5:
+	usb_free_urb(cn_dev->irq);

drivers/input/mouse/foxconn_usb.c line 180

Quoted 10 lines
drivers/input/mouse/foxconn_usb.c new file +10 -0
+err_4:
+	usb_free_coherent(usb_dev, 8, cn_dev->data, cn_dev->data_dma);
+err_3:
+	input_free_device(cn_dev->input_dev);
+err_2:
+	usb_set_intfdata(interface, NULL);
+	usb_put_dev(cn_dev->usb_dev);
+	kfree(cn_dev);
+err_1:
+	dev_err(&interface->dev, "out of memory\n");

Maybe. Or maybe not. We do not know why input_register_device() failed. Just drop the message, driver core will complain about error binding the driver anyway.

drivers/input/mouse/foxconn_usb.c line 188

Quoted 8 lines
drivers/input/mouse/foxconn_usb.c new file +8 -0
+	return error;
+}
+
+static void cntouch_disconnect(struct usb_interface *interface)
+{
+	struct cntouch_device *cn_dev = usb_get_intfdata(interface);
+
+	usb_kill_urb(cn_dev->irq);

Not needed as close() will be called as part of input device unregistration and will cancel the urb for us.

drivers/input/mouse/foxconn_usb.c line 194

Quoted 6 lines
drivers/input/mouse/foxconn_usb.c new file +6 -0
+	input_unregister_device(cn_dev->input_dev);
+	usb_free_urb(cn_dev->irq);
+	usb_free_coherent(cn_dev->usb_dev, 8, cn_dev->data, cn_dev->data_dma);
+	usb_set_intfdata(interface, NULL);
+	usb_put_dev(cn_dev->usb_dev);
+	input_free_device(cn_dev->input_dev);

This is wrong - once input device has been registered you only need to call unregister: once last reference to the object is dropped it will be freed by input core.

drivers/input/mouse/foxconn_usb.c line 196

Quoted 2 lines
drivers/input/mouse/foxconn_usb.c new file +2 -0
+	kfree(cn_dev);
+	dev_info(&interface->dev, DRIVER_DESC " now disconnected\n");

Please drop this message as well.

Quoted 13 lines
drivers/input/mouse/foxconn_usb.c new file +10 -0
+}
+
+static struct usb_driver cntouch_driver = {
+	.name = "CNTouch",
+	.probe = &cntouch_probe,
+	.disconnect = &cntouch_disconnect,
+	.id_table = cntouch_devices,
+};
+
+module_usb_driver(cntouch_driver);
Signature · 1 line
2.1.0

Thanks.

Signature · 1 line
Dmitry
#4 lore raw

PATCH v3 1/1 drivers: input: mouse: Add Foxconn's CNTouch driver

Hi,
Sorry for the delay. I fixed every comments in your code review. I also changed the code to use __set_bit which is easier to read IMHO.

About wether it is an HID compatible device, I took a quick glance but it is not really easy to see... I plan to try out today.

In the meantime here is the patch in case of it is not possible to use the HID interface.

Thanks,
Cheers,

#5 lore raw

PATCH 1/1 drivers: input: mouse: Add Foxconn's CNTouch driver

This commit introduces a new driver for Foxconn CNTouch trackpad that can be found on LDLC's laptop IRIS family. The driver has been inspired from usbmouse.c.

---
 Documentation/input/event-codes.txt |   2 +-
 drivers/input/mouse/Kconfig         |  11 ++
 drivers/input/mouse/Makefile        |   1 +
 drivers/input/mouse/foxconn_usb.c   | 231 ++++++++++++++++++++++++++++++++++++
 4 files changed, 244 insertions(+), 1 deletion(-)
 create mode 100644 drivers/input/mouse/foxconn_usb.c
Documentation/input/event-codes.txt +1 -1
index c587a96..1349a9e 100644
@@ -156,7 +156,7 @@ instead of EV_REL codes.
 
 A few EV_REL codes have special meanings:
 
-* REL_WHEEL, REL_HWHEEL:
+#* REL_WHEEL, REL_HWHEEL:
   - These codes are used for vertical and horizontal scroll wheels,
     respectively.
 
drivers/input/mouse/Kconfig +11 -0
index 4658b5d..e240be3 100644
@@ -407,4 +407,15 @@ config MOUSE_NAVPOINT_PXA27x
 	  To compile this driver as a module, choose M here: the
 	  module will be called navpoint.
 
+config MOUSE_FOXCONN_CNTOUCH
+	tristate "Foxconn CNTouch USB device support"
+	depends on USB_ARCH_HAS_HCD
+	select USB
+	help
+	  This driver adds support for the Foxconn CNTouch trackpad present for
+	  instance on IRIS laptop family from LDLC.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called foxconn_usb.
+
 endif
drivers/input/mouse/Makefile +1 -0
index 8a9c98e..575804f 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_MOUSE_ATARI)		+= atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)		+= bcm5974.o
 obj-$(CONFIG_MOUSE_CYAPA)		+= cyapatp.o
 obj-$(CONFIG_MOUSE_ELAN_I2C)		+= elan_i2c.o
+obj-$(CONFIG_MOUSE_FOXCONN_CNTOUCH)	+= foxconn_usb.o
 obj-$(CONFIG_MOUSE_GPIO)		+= gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)		+= inport.o
 obj-$(CONFIG_MOUSE_LOGIBM)		+= logibm.o
drivers/input/mouse/foxconn_usb.c new file +231 -0

231 lines not on this page · raw message

Signature · 1 line
2.1.0
#6 lore raw

PATCH v4 1/1 drivers: input: mouse: Add Foxconn's CNTouch driver

As expected a new mistake in the previous patch... Sorry about that.

#7 lore raw

PATCH 1/1 drivers: input: mouse: Add Foxconn's CNTouch driver

This commit introduces a new driver for Foxconn CNTouch trackpad that can be found on LDLC's laptop IRIS family. The driver has been inspired from usbmouse.c.

---
 drivers/input/mouse/Kconfig       |  11 ++
 drivers/input/mouse/Makefile      |   1 +
 drivers/input/mouse/foxconn_usb.c | 231 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 243 insertions(+)
 create mode 100644 drivers/input/mouse/foxconn_usb.c
drivers/input/mouse/Kconfig +11 -0
index 4658b5d..e240be3 100644
@@ -407,4 +407,15 @@ config MOUSE_NAVPOINT_PXA27x
 	  To compile this driver as a module, choose M here: the
 	  module will be called navpoint.
 
+config MOUSE_FOXCONN_CNTOUCH
+	tristate "Foxconn CNTouch USB device support"
+	depends on USB_ARCH_HAS_HCD
+	select USB
+	help
+	  This driver adds support for the Foxconn CNTouch trackpad present for
+	  instance on IRIS laptop family from LDLC.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called foxconn_usb.
+
 endif
drivers/input/mouse/Makefile +1 -0
index 8a9c98e..575804f 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_MOUSE_ATARI)		+= atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)		+= bcm5974.o
 obj-$(CONFIG_MOUSE_CYAPA)		+= cyapatp.o
 obj-$(CONFIG_MOUSE_ELAN_I2C)		+= elan_i2c.o
+obj-$(CONFIG_MOUSE_FOXCONN_CNTOUCH)	+= foxconn_usb.o
 obj-$(CONFIG_MOUSE_GPIO)		+= gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)		+= inport.o
 obj-$(CONFIG_MOUSE_LOGIBM)		+= logibm.o
drivers/input/mouse/foxconn_usb.c new file +231 -0

231 lines not on this page · raw message

Signature · 1 line
2.1.0
#8 lore raw

After some researches and tests it seems that the device is not HID compliant...

Signature · 1 line
Thomas Sanchez
#9 lore raw
In reply to Thomas Sanchez

Hi,
Any news/thought regarding this patch ?

Thanks,
Cheers,

2015-02-15 13:44 GMT+01:00 Thomas Sanchez <[email protected]>:

Quoted 284 lines

This commit introduces a new driver for Foxconn CNTouch trackpad that can be found on LDLC's laptop IRIS family. The driver has been inspired from usbmouse.c.

---
 drivers/input/mouse/Kconfig       |  11 ++
 drivers/input/mouse/Makefile      |   1 +
 drivers/input/mouse/foxconn_usb.c | 231 ++++++++++++++++++++++++++++++++++++++
 3 files changed, 243 insertions(+)
 create mode 100644 drivers/input/mouse/foxconn_usb.c
drivers/input/mouse/Kconfig +11 -0
index 4658b5d..e240be3 100644
@@ -407,4 +407,15 @@ config MOUSE_NAVPOINT_PXA27x
          To compile this driver as a module, choose M here: the
          module will be called navpoint.
 
+config MOUSE_FOXCONN_CNTOUCH
+       tristate "Foxconn CNTouch USB device support"
+       depends on USB_ARCH_HAS_HCD
+       select USB
+       help
+         This driver adds support for the Foxconn CNTouch trackpad present for
+         instance on IRIS laptop family from LDLC.
+
+         To compile this driver as a module, choose M here: the
+         module will be called foxconn_usb.
+
 endif
drivers/input/mouse/Makefile +1 -0
index 8a9c98e..575804f 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_MOUSE_ATARI)             += atarimouse.o
 obj-$(CONFIG_MOUSE_BCM5974)            += bcm5974.o
 obj-$(CONFIG_MOUSE_CYAPA)              += cyapatp.o
 obj-$(CONFIG_MOUSE_ELAN_I2C)           += elan_i2c.o
+obj-$(CONFIG_MOUSE_FOXCONN_CNTOUCH)    += foxconn_usb.o
 obj-$(CONFIG_MOUSE_GPIO)               += gpio_mouse.o
 obj-$(CONFIG_MOUSE_INPORT)             += inport.o
 obj-$(CONFIG_MOUSE_LOGIBM)             += logibm.o
drivers/input/mouse/foxconn_usb.c new file +231 -1
new file mode 100644
index 0000000..3615b20
@@ -0,0 +1,231 @@
+/*
+ *  Copyright (c) 2015-2016 Thomas Sanchez
+ *
+ *  CNTouch driver
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/usb.h>
+#include <linux/usb/input.h>
+
+#define USB_VENDOR_ID_FOXCONN          0x294e
+#define USB_DEVICE_ID_FOXCONN_CNTOUCH  0x1001
+
+#define DRIVER_DESC    "CNTouch USB Driver"
+
+static const struct usb_device_id cntouch_devices[] = {
+       {USB_DEVICE(USB_VENDOR_ID_FOXCONN, USB_DEVICE_ID_FOXCONN_CNTOUCH)},
+       {},
+};
+
+MODULE_AUTHOR("Thomas Sanchez, [email protected]");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL");
+
+MODULE_DEVICE_TABLE(usb, cntouch_devices);
+
+struct cntouch_device {
+       struct usb_device *usb_dev;
+       struct input_dev *input_dev;
+       struct urb *irq;
+       signed char *data;
+       dma_addr_t data_dma;
+       char usb_path[64];
+};
+
+static void cntouch_irq(struct urb *urb)
+{
+       struct cntouch_device *cn_dev = urb->context;
+       signed char *data = cn_dev->data;
+       struct input_dev *dev = cn_dev->input_dev;
+       int status;
+
+       switch (urb->status) {
+       case 0:
+               break;
+       case -ECONNRESET:
+       case -ENOENT:
+       case -ESHUTDOWN:
+               return;
+       default:
+               goto resubmit;
+       }
+
+       input_report_rel(dev, REL_X, data[1]);
+       input_report_rel(dev, REL_Y, data[2]);
+
+       input_report_rel(dev, REL_WHEEL, data[3]);
+       input_report_rel(dev, REL_HWHEEL, data[4]);
+
+       input_report_key(dev, BTN_LEFT, data[0] & 0x01);
+       input_report_key(dev, BTN_RIGHT, data[0] & 0x02);
+
+       input_report_key(
+           dev, data[4] == 0 ? BTN_TOOL_FINGER : BTN_TOOL_DOUBLETAP, 1);
+
+       input_sync(dev);
+
+resubmit:
+       status = usb_submit_urb(urb, GFP_ATOMIC);
+       if (status) {
+               dev_err(&cn_dev->usb_dev->dev,
+                       "can't resubmit intr, %s-%s/input0, status %d\n",
+                       cn_dev->usb_dev->bus->bus_name,
+                       cn_dev->usb_dev->devpath, status);
+       }
+}
+
+static int cntouch_open(struct input_dev *dev)
+{
+       struct cntouch_device *cn_dev = input_get_drvdata(dev);
+
+       if (usb_submit_urb(cn_dev->irq, GFP_KERNEL))
+               return -EIO;
+       return 0;
+}
+
+static void cntouch_close(struct input_dev *dev)
+{
+       struct cntouch_device *cn_dev = input_get_drvdata(dev);
+
+       usb_kill_urb(cn_dev->irq);
+}
+
+static int cntouch_probe(struct usb_interface *interface,
+                        const struct usb_device_id *id)
+{
+       struct usb_device *usb_dev = interface_to_usbdev(interface);
+       struct cntouch_device *cn_dev;
+       struct usb_host_interface *host_interface;
+       struct usb_endpoint_descriptor *endpoint;
+       int pipe, maxp;
+       int error;
+
+       host_interface = interface->cur_altsetting;
+
+       if (host_interface->desc.bNumEndpoints != 1)
+               return -ENODEV;
+
+       endpoint = &host_interface->endpoint[0].desc;
+       if (!usb_endpoint_is_int_in(endpoint))
+               return -ENODEV;
+
+       pipe = usb_rcvintpipe(usb_dev, endpoint->bEndpointAddress);
+       maxp = usb_maxpacket(usb_dev, pipe, usb_pipeout(pipe));
+
+       cn_dev = kzalloc(sizeof(*cn_dev), GFP_KERNEL);
+       if (cn_dev == NULL) {
+               error = -ENOMEM;
+               goto err_1;
+       }
+
+       cn_dev->input_dev = input_allocate_device();
+       if (!cn_dev->input_dev) {
+               error = -ENOMEM;
+               goto err_2;
+       }
+
+       cn_dev->data =
+           usb_alloc_coherent(usb_dev, 8, GFP_ATOMIC, &cn_dev->data_dma);
+       if (!cn_dev->data) {
+               error = -ENOMEM;
+               goto err_3;
+       }
+
+       cn_dev->irq = usb_alloc_urb(0, GFP_KERNEL);
+       if (!cn_dev->irq) {
+               error = -ENOMEM;
+               goto err_4;
+       }
+
+       usb_set_intfdata(interface, cn_dev);
+
+       usb_make_path(usb_dev, cn_dev->usb_path, sizeof(cn_dev->usb_path));
+       strlcat(cn_dev->usb_path, "/input0", sizeof(cn_dev->usb_path));
+
+       cn_dev->input_dev->name = "CNTouch";
+       cn_dev->input_dev->phys = cn_dev->usb_path;
+       usb_to_input_id(usb_dev, &cn_dev->input_dev->id);
+       cn_dev->input_dev->dev.parent = &interface->dev;
+
+       __set_bit(EV_REL, cn_dev->input_dev->evbit);
+       __set_bit(EV_KEY, cn_dev->input_dev->evbit);
+
+       __set_bit(BTN_MOUSE, cn_dev->input_dev->keybit);
+       __set_bit(BTN_LEFT, cn_dev->input_dev->keybit);
+       __set_bit(BTN_RIGHT, cn_dev->input_dev->keybit);
+       __set_bit(BTN_TOOL_FINGER, cn_dev->input_dev->keybit);
+       __set_bit(BTN_TOOL_DOUBLETAP, cn_dev->input_dev->keybit);
+
+       __set_bit(REL_X, cn_dev->input_dev->relbit);
+       __set_bit(REL_Y, cn_dev->input_dev->relbit);
+       __set_bit(REL_WHEEL, cn_dev->input_dev->relbit);
+       __set_bit(REL_HWHEEL, cn_dev->input_dev->relbit);
+
+       input_set_drvdata(cn_dev->input_dev, cn_dev);
+
+       cn_dev->input_dev->open = cntouch_open;
+       cn_dev->input_dev->close = cntouch_close;
+
+       usb_fill_int_urb(cn_dev->irq, usb_dev, pipe, cn_dev->data,
+                        (maxp > 8 ? 8 : maxp), cntouch_irq, cn_dev,
+                        endpoint->bInterval);
+       cn_dev->irq->transfer_dma = cn_dev->data_dma;
+       cn_dev->irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+
+       error = input_register_device(cn_dev->input_dev);
+       if (error)
+               goto err_5;
+
+       return 0;
+
+err_5:
+       usb_free_urb(cn_dev->irq);
+err_4:
+       usb_free_coherent(usb_dev, 8, cn_dev->data, cn_dev->data_dma);
+err_3:
+       input_free_device(cn_dev->input_dev);
+err_2:
+       usb_set_intfdata(interface, NULL);
+       usb_put_dev(cn_dev->usb_dev);
+       kfree(cn_dev);
+err_1:
+       return error;
+}
+
+static void cntouch_disconnect(struct usb_interface *interface)
+{
+       struct cntouch_device *cn_dev = usb_get_intfdata(interface);
+
+       input_unregister_device(cn_dev->input_dev);
+       usb_free_urb(cn_dev->irq);
+       usb_free_coherent(cn_dev->usb_dev, 8, cn_dev->data, cn_dev->data_dma);
+       usb_set_intfdata(interface, NULL);
+       usb_put_dev(cn_dev->usb_dev);
+       kfree(cn_dev);
+}
+
+static struct usb_driver cntouch_driver = {
+       .name = "CNTouch",
+       .probe = &cntouch_probe,
+       .disconnect = &cntouch_disconnect,
+       .id_table = cntouch_devices,
+};
+
+module_usb_driver(cntouch_driver);
--

2.1.0

Signature · 1 line
Thomas Sanchez