ARM: atmel: enable spl for sama5d4 related boards
Subsystems (2)
v2 cover ARM: atmel: enable spl for sama5d4 related boards
This patch enable SPL support for both sama5d4ek and sama5d4 xplained board which are based on SAMA5D4 SoC.
These two boards both support boot up from NAND flash, SD/MMC card and also serial flash.
This patch series based on the "ARM: atmel: enable usb ethernet gadget"
Changes in v2:
- change CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION to CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
- change CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION to CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
Bo Shen (13):
ARM: atmel: clock: make it possible to configure HMX32
ARM: atmel: sama5: add bus matrix header file
ARM: atmel: sama5: add sfr register header file
ARM: atmel: spl: add weak bus matrix init function
ARM: atmel: spl: add saic to aic redirect function
ARM: atmel: spl: can not disable osc for sama5d4
ARM: atmel: sama5d4: add matrix1 base addr definition
ARM: atmel: sama5d4: add bus matrix init function
ARM: atmel: sama5d4: add interrupt redirec function
ARM: atmel: sama5d4: can access DDR in interleave mode
ARM: atmel: sama5d4: build related file when enable SPL
ARM: atmel: sama5d4ek: enable SPL support
ARM: atmel: sama5d4_xplained: enable spl support
arch/arm/Kconfig | 2 + arch/arm/cpu/armv7/at91/clock.c | 8 +++ arch/arm/cpu/armv7/at91/sama5d4_devices.c | 47 ++++++++++++++ arch/arm/cpu/at91-common/Makefile | 1 + arch/arm/cpu/at91-common/mpddrc.c | 2 +- arch/arm/cpu/at91-common/spl_atmel.c | 16 +++++ arch/arm/include/asm/arch-at91/at91_common.h | 1 + arch/arm/include/asm/arch-at91/sama5_matrix.h | 37 +++++++++++ arch/arm/include/asm/arch-at91/sama5_sfr.h | 38 +++++++++++ arch/arm/include/asm/arch-at91/sama5d4.h | 2 + board/atmel/sama5d4_xplained/sama5d4_xplained.c | 85 +++++++++++++++++++++++++ board/atmel/sama5d4ek/sama5d4ek.c | 85 +++++++++++++++++++++++++ configs/sama5d4_xplained_mmc_defconfig | 1 + configs/sama5d4_xplained_nandflash_defconfig | 1 + configs/sama5d4_xplained_spiflash_defconfig | 1 + configs/sama5d4ek_mmc_defconfig | 1 + configs/sama5d4ek_nandflash_defconfig | 1 + configs/sama5d4ek_spiflash_defconfig | 1 + include/configs/sama5d4_xplained.h | 56 ++++++++++++++++ include/configs/sama5d4ek.h | 56 ++++++++++++++++ 20 files changed, 441 insertions(+), 1 deletion(-) create mode 100644 arch/arm/include/asm/arch-at91/sama5_matrix.h create mode 100644 arch/arm/include/asm/arch-at91/sama5_sfr.h
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 1/13 ARM: atmel: clock: make it possible to configure HMX32
---
Changes in v2: None
arch/arm/cpu/armv7/at91/clock.c | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm/cpu/armv7/at91/clock.c +8 -0
@@ -130,10 +130,18 @@ void at91_mck_init(u32 mckr)AT91_PMC_MCKR_PRES_MASK |AT91_PMC_MCKR_MDIV_MASK | AT91_PMC_MCKR_PLLADIV_2); +#ifdef CPU_HAS_H32MXDIV + tmp &= ~AT91_PMC_MCKR_H32MXDIV ; +#endif + tmp |= mckr & (AT91_PMC_MCKR_CSS_MASK |AT91_PMC_MCKR_PRES_MASK |AT91_PMC_MCKR_MDIV_MASK |AT91_PMC_MCKR_PLLADIV_2 ); +#ifdef CPU_HAS_H32MXDIV + tmp |= mckr &AT91_PMC_MCKR_H32MXDIV ; +#endif +writel (tmp, &pmc->mckr);while (!(readl (&pmc->sr) &AT91_PMC_MCKRDY ))
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 1/13 ARM: atmel: clock: make it possible to configure HMX32
Dear Bo Shen,
Quoted 7 lines · Bo Shen
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/cpu/armv7/at91/clock.c| 8 ++++++++1 file changed, 8 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 2/13 ARM: atmel: sama5: add bus matrix header file
In reply to Bo ShenThis matrix header file can be shared between sama5d3 and sama5d4 soc.
---
Changes in v2: None
arch/arm/include/asm/arch-at91/sama5_matrix.h | 37 +++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) create mode 100644 arch/arm/include/asm/arch-at91/sama5_matrix.h
arch/arm/include/asm/arch-at91/sama5_matrix.h new file +37 -0
@@ -0,0 +1,37 @@ +/* +* Bus Matrix header file for the SAMA5 family +* +* Copyright (C) 2014 Atmel +* Bo Shen <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __SAMA5_MATRIX_H +#define __SAMA5_MATRIX_H + +struct atmel_matrix { +u32 mcfg[16 ];/* 0x00 ~ 0x3c: Master Configuration Register */ +u32 scfg[16 ];/* 0x40 ~ 0x7c: Slave Configuration Register */ +u32 pras[16 ][2 ];/* 0x80 ~ 0xfc: Priority Register A/B */ +u32 reserved1[20 ];/* 0x100 ~ 0x14c */ +u32 meier;/* 0x150: Master Error Interrupt Enable Register */ +u32 meidr;/* 0x154: Master Error Interrupt Disable Register */ +u32 meimr;/* 0x158: Master Error Interrupt Mask Register */ +u32 mesr;/* 0x15c: Master Error Status Register */ +u32 mear[16 ];/* 0x160 ~ 0x19c: Master Error Address Register */ +u32 reserved2[17 ];/* 0x1A0 ~ 0x1E0 */ +u32 wpmr;/* 0x1E4: Write Protection Mode Register */ +u32 wpsr;/* 0x1E8: Write Protection Status Register */ +u32 reserved3[5 ];/* 0x1EC ~ 0x1FC */ +u32 ssr[16 ];/* 0x200 ~ 0x23c: Security Slave Register */ +u32 sassr[16 ];/* 0x240 ~ 0x27c: Security Areas Split Slave Register */ +u32 srtsr[16 ];/* 0x280 ~ 0x2bc: Security Region Top Slave */ +u32 spselr[3 ];/* 0x2c0 ~ 0x2c8: Security Peripheral Select Register */ +}; + +/* Bit field in WPMR */ +#define ATMEL_MATRIX_WPMR_WPKEY 0x4D415400 +#define ATMEL_MATRIX_WPMR_WPEN 0x00000001 + +#endif
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 2/13 ARM: atmel: sama5: add bus matrix header file
Dear Bo Shen,
Quoted 5 lines · Bo Shen
This matrix header file can be shared between sama5d3 and sama5d4 soc.
Signed-off-by Bo Shen <[email protected]>[whitespace adaptions for 80 char compliance]Signed-off-by Andreas Bie?mann <[email protected]>
Quoted 7 lines
---
Changes in v2: None
arch/arm/include/asm/arch-at91/sama5_matrix.h| 37 +++++++++++++++++++++++++++1 file changed, 37 insertions(+)create mode 100644
arch/arm/include/asm/arch-at91/sama5_matrix.h
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 3/13 ARM: atmel: sama5: add sfr register header file
In reply to Bo ShenThe SFR (special function registers) can be shared bwteen sama5d3 and sama5d4 soc.
---
Changes in v2: None
arch/arm/include/asm/arch-at91/sama5_sfr.h | 38 ++++++++++++++++++++++++++++++ 1 file changed, 38 insertions(+) create mode 100644 arch/arm/include/asm/arch-at91/sama5_sfr.h
arch/arm/include/asm/arch-at91/sama5_sfr.h new file +38 -0
@@ -0,0 +1,38 @@ +/* +* Special Function Register (SFR) +* +* Copyright (C) 2014 Atmel +* Bo Shen <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __SAMA5_SFR_H +#define __SAMA5_SFR_H + +struct atmel_sfr { +u32 reserved1;/* 0x00 */ +u32 ddrcfg;/* 0x04: DDR Configuration Register */ +u32 reserved2;/* 0x08 */ +u32 reserved3;/* 0x0c */ +u32 ohciicr;/* 0x10: OHCI Interrupt Configuration Register */ +u32 ohciisr;/* 0x14: OHCI Interrupt Status Register */ +u32 reserved4[4 ];/* 0x18 ~ 0x24 */ +u32 secure;/* 0x28: Security Configuration Register */ +u32 reserved5[5 ];/* 0x2c ~ 0x3c */ +u32 ebicfg;/* 0x40: EBI Configuration Register */ +u32 reserved6[2 ];/* 0x44 ~ 0x48 */ +u32 sn0;/* 0x4c */ +u32 sn1;/* 0x50 */ +u32 aicredir;/* 0x54 */ +}; + +/* Bit field in DDRCFG */ +#define ATMEL_SFR_DDRCFG_FDQIEN 0x00010000 +#define ATMEL_SFR_DDRCFG_FDQSIEN 0x00020000 + +/* Bit field in AICREDIR */ +#define ATMEL_SFR_AICREDIR_KEY 0x5F67B102 +#define ATMEL_SFR_AICREDIR_NSAIC 0x00000001 + +#endif
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 3/13 ARM: atmel: sama5: add sfr register header file
Dear Bo Shen,
Quoted 6 lines · Bo Shen
The SFR (special function registers) can be shared bwteen sama5d3 and sama5d4 soc.
Signed-off-by Bo Shen <[email protected]>[whitespace adoptions for 80 char compliance]Signed-off-by Andreas Bie?mann <[email protected]>
Quoted 7 lines
---
Changes in v2: None
arch/arm/include/asm/arch-at91/sama5_sfr.h| 38 ++++++++++++++++++++++++++++++1 file changed, 38 insertions(+)create mode 100644
arch/arm/include/asm/arch-at91/sama5_sfr.h
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 4/13 ARM: atmel: spl: add weak bus matrix init function
In reply to Bo ShenSome SoC need to configure the bus matrix, add an weak function to be replace by real function.
---
Changes in v2: None
arch/arm/cpu/at91-common/spl_atmel.c | 7 +++++++ 1 file changed, 7 insertions(+)
arch/arm/cpu/at91-common/spl_atmel.c +7 -0
@@ -58,6 +58,11 @@ static void switch_to_main_crystal_osc(void)writel (tmp, &pmc->mor); } +__weak void matrix_init (void ) +{ +/* This only be used for sama5d4 soc now */ +} +void s_init (void ) {switch_to_main_crystal_osc ();
@@ -70,6 +75,8 @@ void s_init(void)at91_clock_init (CONFIG_SYS_AT91_MAIN_CLOCK ); +matrix_init (); +timer_init ();board_early_init_f ();
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 4/13 ARM: atmel: spl: add weak bus matrix init function
Dear Bo Shen,
Quoted 10 lines · Bo Shen
Some SoC need to configure the bus matrix, add an weak function to be replace by real function.
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/cpu/at91-common/spl_atmel.c| 7 +++++++1 file changed, 7 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 5/13 ARM: atmel: spl: add saic to aic redirect function
In reply to Bo ShenSome SoC need to redirect the saic to aic to make the interrupt to work, here add a weak function to be replaced by real function.
---
Changes in v2: None
arch/arm/cpu/at91-common/spl_atmel.c | 7 +++++++ arch/arm/include/asm/arch-at91/at91_common.h | 1 + 2 files changed, 8 insertions(+)
arch/arm/cpu/at91-common/spl_atmel.c +7 -0
@@ -63,6 +63,11 @@ __weak void matrix_init(void)/* This only be used for sama5d4 soc now */ } +__weak void redirect_int_from_saic_to_aic (void ) +{ +/* This only be used for sama5d4 soc now */ +} +void s_init (void ) {switch_to_main_crystal_osc ();
@@ -77,6 +82,8 @@ void s_init(void)matrix_init (); +redirect_int_from_saic_to_aic (); +timer_init ();board_early_init_f ();
arch/arm/include/asm/arch-at91/at91_common.h +1 -0
@@ -33,5 +33,6 @@ void at91_mck_init(u32 mckr);void at91_spl_board_init (void );void at91_disable_wdt (void );void matrix_init (void ); +void redirect_int_from_saic_to_aic (void );#endif /* AT91_COMMON_H */
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 5/13 ARM: atmel: spl: add saic to aic redirect function
Dear Bo Shen,
Quoted 11 lines · Bo Shen
Some SoC need to redirect the saic to aic to make the interrupt to work, here add a weak function to be replaced by real function.
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/cpu/at91-common/spl_atmel.c| 7 +++++++arch/arm/include/asm/arch-at91/at91_common.h| 1 +2 files changed, 8 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 6/13 ARM: atmel: spl: can not disable osc for sama5d4
In reply to Bo ShenThe SAMA5D4 SoC on chip rc oscillator can not be disabled.
---
Changes in v2: None
arch/arm/cpu/at91-common/spl_atmel.c | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/cpu/at91-common/spl_atmel.c +2 -0
@@ -51,11 +51,13 @@ static void switch_to_main_crystal_osc(void)while (!(readl (&pmc->mcfr) &AT91_PMC_MAINRDY )) ; +#ifndef CONFIG_SAMA5D4 tmp =readl (&pmc->mor); tmp &= ~AT91_PMC_MOR_MOSCRCEN ; tmp &= ~AT91_PMC_MOR_KEY (0xff ); tmp |=AT91_PMC_MOR_KEY (0x37 );writel (tmp, &pmc->mor); +#endif }__weak void matrix_init (void )
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 6/13 ARM: atmel: spl: can not disable osc for sama5d4
Dear Bo Shen,
Quoted 9 lines · Bo Shen
The SAMA5D4 SoC on chip rc oscillator can not be disabled.
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/cpu/at91-common/spl_atmel.c| 2 ++1 file changed, 2 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 7/13 ARM: atmel: sama5d4: add matrix1 base addr definition
In reply to Bo Shen---
Changes in v2: None
arch/arm/include/asm/arch-at91/sama5d4.h | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/include/asm/arch-at91/sama5d4.h +2 -0
@@ -126,6 +126,8 @@#define ATMEL_BASE_ADC 0xfc034000#define ATMEL_BASE_TWI3 0xfc038000 +#define ATMEL_BASE_MATRIX1 0xfc054000 +#define ATMEL_BASE_SMC 0xfc05c000#define ATMEL_BASE_PMECC (ATMEL_BASE_SMC + 0x070)#define ATMEL_BASE_PMERRLOC (ATMEL_BASE_SMC + 0x500)
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 7/13 ARM: atmel: sama5d4: add matrix1 base addr definition
Dear Bo Shen,
Quoted 7 lines · Bo Shen
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/include/asm/arch-at91/sama5d4.h| 2 ++1 file changed, 2 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 8/13 ARM: atmel: sama5d4: add bus matrix init function
In reply to Bo Shen---
Changes in v2: None
arch/arm/cpu/armv7/at91/sama5d4_devices.c | 35 +++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm/cpu/armv7/at91/sama5d4_devices.c +35 -0
@@ -10,6 +10,7 @@#include <asm/arch/at91_common.h> #include <asm/arch/at91_pmc.h> #include <asm/arch/clk.h> +#include <asm/arch/sama5_matrix.h> #include <asm/arch/sama5d4.h> char *get_cpu_name ()
@@ -44,3 +45,37 @@ void at91_udp_hw_init(void)at91_periph_clk_enable (ATMEL_ID_UDPHS ); }#endif + +#ifdef CONFIG_SPL_BUILD +void matrix_init (void ) +{ +struct atmel_matrix *h64mx = (struct atmel_matrix *)ATMEL_BASE_MATRIX0 ; +struct atmel_matrix *h32mx = (struct atmel_matrix *)ATMEL_BASE_MATRIX1 ; +int i; + +/* Disable the write protect */ +writel (ATMEL_MATRIX_WPMR_WPKEY & ~ATMEL_MATRIX_WPMR_WPEN , &h64mx->wpmr); +writel (ATMEL_MATRIX_WPMR_WPKEY & ~ATMEL_MATRIX_WPMR_WPEN , &h32mx->wpmr); + +/* DDR port 1 ~ poart 7, slave number is: 4 ~ 10 */ +for (i =4 ; i <=10 ; i++) { +writel (0x000f0f0f , &h64mx->ssr[i]); +writel (0x0000ffff , &h64mx->sassr[i]); +writel (0x0000000f , &h64mx->srtsr[i]); + } + +/* CS3 */ +writel (0x00c0c0c0 , &h32mx->ssr[3 ]); +writel (0xff000000 , &h32mx->sassr[3 ]); +writel (0xff000000 , &h32mx->srtsr[3 ]); + +/* NFC SRAM */ +writel (0x00010101 , &h32mx->ssr[4 ]); +writel (0x00000001 , &h32mx->sassr[4 ]); +writel (0x00000001 , &h32mx->srtsr[4 ]); + +/* Enable the write protect */ +writel (ATMEL_MATRIX_WPMR_WPKEY |ATMEL_MATRIX_WPMR_WPEN , &h64mx->wpmr); +writel (ATMEL_MATRIX_WPMR_WPKEY |ATMEL_MATRIX_WPMR_WPEN , &h32mx->wpmr); +} +#endif
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 8/13 ARM: atmel: sama5d4: add bus matrix init function
Dear Bo Shen,
Quoted 7 lines · Bo Shen
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/cpu/armv7/at91/sama5d4_devices.c| 35 +++++++++++++++++++++++++++++++1 file changed, 35 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 9/13 ARM: atmel: sama5d4: add interrupt redirec function
In reply to Bo Shen---
Changes in v2: None
arch/arm/cpu/armv7/at91/sama5d4_devices.c | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm/cpu/armv7/at91/sama5d4_devices.c +12 -0
@@ -11,6 +11,7 @@#include <asm/arch/at91_pmc.h> #include <asm/arch/clk.h> #include <asm/arch/sama5_matrix.h> +#include <asm/arch/sama5_sfr.h> #include <asm/arch/sama5d4.h> char *get_cpu_name ()
@@ -78,4 +79,15 @@ void matrix_init(void)writel (ATMEL_MATRIX_WPMR_WPKEY |ATMEL_MATRIX_WPMR_WPEN , &h64mx->wpmr); writel(ATMEL_MATRIX_WPMR_WPKEY | ATMEL_MATRIX_WPMR_WPEN, &h32mx->wpmr); } + +void redirect_int_from_saic_to_aic (void ) +{ +struct atmel_sfr *sfr = (struct atmel_sfr *)ATMEL_BASE_SFR ; +u32 key32; + +if (!(readl (&sfr->aicredir) &ATMEL_SFR_AICREDIR_NSAIC )) { + key32 =readl (&sfr->sn1) ^ATMEL_SFR_AICREDIR_KEY ; +writel ((key32 |ATMEL_SFR_AICREDIR_NSAIC ), &sfr->aicredir); + } +}#endif
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 9/13 ARM: atmel: sama5d4: add interrupt redirect function
Dear Bo Shen,
Quoted 9 lines · Bo Shen
Signed-off-by Bo Shen <[email protected]>[fix subject]Signed-off-by Andreas Bie?mann <[email protected]>---
Changes in v2: None
arch/arm/cpu/armv7/at91/sama5d4_devices.c| 12 ++++++++++++1 file changed, 12 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 10/13 ARM: atmel: sama5d4: can access DDR in interleave mode
In reply to Bo ShenThe SAMAA5D4 SoC can access DDR in interleave mode.
---
Changes in v2: None
arch/arm/cpu/at91-common/mpddrc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/cpu/at91-common/mpddrc.c +1 -1
@@ -19,7 +19,7 @@ static inline void atmel_mpddr_op(int mode, u32 ram_address)static int ddr2_decodtype_is_seq (u32 cr) { -#if defined(CONFIG_SAMA5D3 ) +#if defined(CONFIG_SAMA5D3 ) || defined(CONFIG_SAMA5D4 )if (cr &ATMEL_MPDDRC_CR_DECOD_INTERLEAVED )return 0 ;#endif
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 10/13 ARM: atmel: sama5d4: can access DDR in interleave mode
Dear Bo Shen,
Quoted 9 lines · Bo Shen
The SAMAA5D4 SoC can access DDR in interleave mode.
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/cpu/at91-common/mpddrc.c| 2 +-1 file changed, 1 insertion(+), 1 deletion(-)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 11/13 ARM: atmel: sama5d4: build related file when enable SPL
In reply to Bo Shen---
Changes in v2: None
arch/arm/cpu/at91-common/Makefile | 1 + 1 file changed, 1 insertion(+)
arch/arm/cpu/at91-common/Makefile +1 -0
@@ -13,5 +13,6 @@ ifneq ($(CONFIG_SPL_BUILD),) obj-$(CONFIG_AT91SAM9G20) += sdram.o spl_at91.o obj-$(CONFIG_AT91SAM9M10G45) += mpddrc.o spl_at91.o obj-$(CONFIG_SAMA5D3) += mpddrc.o spl_atmel.o +obj-$(CONFIG_SAMA5D4) += mpddrc.o spl_atmel.o obj-y += spl.o endif
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 11/13 ARM: atmel: sama5d4: build related file when enable SPL
Dear Bo Shen,
Quoted 7 lines · Bo Shen
Signed-off-by Bo Shen <[email protected]>---
Changes in v2: None
arch/arm/cpu/at91-common/Makefile| 1 +1 file changed, 1 insertion(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 12/13 ARM: atmel: sama5d4ek: enable SPL support
In reply to Bo ShenThe sama5d4ek support boot up from NAND flash, SD/MMC card and also the SPI flash.
---
Changes in v2:
- change CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION to CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
arch/arm/Kconfig | 1 + board/atmel/sama5d4ek/sama5d4ek.c | 85 +++++++++++++++++++++++++++++++++++ configs/sama5d4ek_mmc_defconfig | 1 + configs/sama5d4ek_nandflash_defconfig | 1 + configs/sama5d4ek_spiflash_defconfig | 1 + include/configs/sama5d4ek.h | 56 +++++++++++++++++++++++ 6 files changed, 145 insertions(+)
arch/arm/Kconfig +1 -0
@@ -522,6 +522,7 @@ config TARGET_SAMA5D4_XPLAINED config TARGET_SAMA5D4EK bool "Support sama5d4ek" select CPU_V7 + select SUPPORT_SPL config TARGET_BCM28155_AP bool "Support bcm28155_ap"
board/atmel/sama5d4ek/sama5d4ek.c +85 -0
94 lines not on this page · raw message
configs/sama5d4ek_mmc_defconfig +1 -0
@@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_MMC" +S:CONFIG_ARM=y +S:CONFIG_TARGET_SAMA5D4EK=y
configs/sama5d4ek_nandflash_defconfig +1 -0
@@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_NANDFLASH" +S:CONFIG_ARM=y +S:CONFIG_TARGET_SAMA5D4EK=y
configs/sama5d4ek_spiflash_defconfig +1 -0
@@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_SERIALFLASH" +S:CONFIG_ARM=y +S:CONFIG_TARGET_SAMA5D4EK=y
include/configs/sama5d4ek.h +56 -0
75 lines not on this page · raw message
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 12/13 ARM: atmel: sama5d4ek: enable SPL support
Dear Bo Shen,
Quoted 9 lines · Bo Shen
The sama5d4ek support boot up from NAND flash, SD/MMC card and also the SPI flash.
Signed-off-by Bo Shen <[email protected]>---
Changes in v2:
- changeCONFIG_SYS_MMC_SD_FS_BOOT_PARTITIONtoCONFIG_SYS_MMCSD_FS_BOOT_PARTITION
Quoted 7 lines
arch/arm/Kconfig | 1 + board/atmel/sama5d4ek/sama5d4ek.c | 85 +++++++++++++++++++++++++++++++++++ configs/sama5d4ek_mmc_defconfig | 1 + configs/sama5d4ek_nandflash_defconfig | 1 + configs/sama5d4ek_spiflash_defconfig | 1 + include/configs/sama5d4ek.h | 56 +++++++++++++++++++++++ 6 files changed, 145 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann
PATCH v2 13/13 ARM: atmel: sama5d4_xplained: enable spl support
In reply to Bo Shen---
Changes in v2:
- change CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION to CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
arch/arm/Kconfig | 1 + board/atmel/sama5d4_xplained/sama5d4_xplained.c | 85 +++++++++++++++++++++++++ configs/sama5d4_xplained_mmc_defconfig | 1 + configs/sama5d4_xplained_nandflash_defconfig | 1 + configs/sama5d4_xplained_spiflash_defconfig | 1 + include/configs/sama5d4_xplained.h | 56 ++++++++++++++++ 6 files changed, 145 insertions(+)
arch/arm/Kconfig +1 -0
@@ -518,6 +518,7 @@ config TARGET_SAMA5D3XEK config TARGET_SAMA5D4_XPLAINED bool "Support sama5d4_xplained" select CPU_V7 + select SUPPORT_SPL config TARGET_SAMA5D4EK bool "Support sama5d4ek"
board/atmel/sama5d4_xplained/sama5d4_xplained.c +85 -0
94 lines not on this page · raw message
configs/sama5d4_xplained_mmc_defconfig +1 -0
@@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_MMC" +S:CONFIG_ARM=y +S:CONFIG_TARGET_SAMA5D4_XPLAINED=y
configs/sama5d4_xplained_nandflash_defconfig +1 -0
@@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_NANDFLASH" +S:CONFIG_ARM=y +S:CONFIG_TARGET_SAMA5D4_XPLAINED=y
configs/sama5d4_xplained_spiflash_defconfig +1 -0
@@ -1,3 +1,4 @@ +CONFIG_SPL=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_SERIALFLASH" +S:CONFIG_ARM=y +S:CONFIG_TARGET_SAMA5D4_XPLAINED=y
include/configs/sama5d4_xplained.h +56 -0
75 lines not on this page · raw message
Signature · 1 line
2.1.0.24.g4109c28
PATCH v2 13/13 ARM: atmel: sama5d4_xplained: enable spl support
Dear Bo Shen,
Quoted 6 lines · Bo Shen
Signed-off-by Bo Shen <[email protected]>---
Changes in v2:
- changeCONFIG_SYS_MMC_SD_FS_BOOT_PARTITIONtoCONFIG_SYS_MMCSD_FS_BOOT_PARTITION
Quoted 7 lines
arch/arm/Kconfig | 1 + board/atmel/sama5d4_xplained/sama5d4_xplained.c | 85 +++++++++++++++++++++++++ configs/sama5d4_xplained_mmc_defconfig | 1 + configs/sama5d4_xplained_nandflash_defconfig | 1 + configs/sama5d4_xplained_spiflash_defconfig | 1 + include/configs/sama5d4_xplained.h | 56 ++++++++++++++++ 6 files changed, 145 insertions(+)
applied to u-boot-atmel/master, thanks!
Best regards,
Andreas Bie?mann