Skip to contentSkip to conversation

mx53loco: Fix boot hang during reboot stress test

PATCH New Fabio Estevam 2 participants 2 messages Feb 9, 2015 Arm i.MX and Layerscape

lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH 1/1 mx53loco: Fix boot hang during reboot stress test

From: Fabio Estevam <[email protected]>

Currently by running the following test:

=> setenv bootcmd reset
=> save
=> reset

, we observe a hang after approximately 20-30 minutes of stress reboot test.

Investigation of this issue revealed that when a single DDR chip select is used, the hang does not happen. It only happens when the two chip selects are active.

MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence":

"The controller must keep the memory lines quiet (except for CK) for the ZQ calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256 for other ZQCL and 64 for ZQCS)."

According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL:

"Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines. Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)"

So make sure to activate one chip select at time (CS0 first and then CS1 later), so that the required JEDEC delay is respected for each chip select.

With this change applied the board has gone through three days of reboot stress test without any hang.

---
 board/freescale/mx53loco/imximage.cfg | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
board/freescale/mx53loco/imximage.cfg +2 -1
index d1c1931..a5f1d98 100644
@@ -59,7 +59,7 @@ DATA 4 0x63fd9090 0x4d444c44
 DATA 4 0x63fd907c 0x01370138
 DATA 4 0x63fd9080 0x013b013c
 DATA 4 0x63fd9018 0x00011740
-DATA 4 0x63fd9000 0xc3190000
+DATA 4 0x63fd9000 0x83190000
 DATA 4 0x63fd900c 0x9f5152e3
 DATA 4 0x63fd9010 0xb68e8a63
 DATA 4 0x63fd9014 0x01ff00db
@@ -72,6 +72,7 @@ DATA 4 0x63fd901c 0x00008033
 DATA 4 0x63fd901c 0x00028031
 DATA 4 0x63fd901c 0x052080b0
 DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd9000 0xc3190000
 DATA 4 0x63fd901c 0x0000803a
 DATA 4 0x63fd901c 0x0000803b
 DATA 4 0x63fd901c 0x00028039
Signature · 1 line
1.9.1
#1 lore raw

PATCH 1/1 mx53loco: Fix boot hang during reboot stress test

Hi Fabio,

Quoted 50 lines · Fabio Estevam

From: Fabio Estevam <[email protected]>

Currently by running the following test:

=> setenv bootcmd reset
=> save
=> reset

, we observe a hang after approximately 20-30 minutes of stress reboot test.

Investigation of this issue revealed that when a single DDR chip select is used, the hang does not happen. It only happens when the two chip selects are active.

MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence":

"The controller must keep the memory lines quiet (except for CK) for the ZQ calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256 for other ZQCL and 64 for ZQCS)."

According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL:

"Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines. Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)"

So make sure to activate one chip select at time (CS0 first and then CS1 later), so that the required JEDEC delay is respected for each chip select.

With this change applied the board has gone through three days of reboot stress test without any hang.

---
 board/freescale/mx53loco/imximage.cfg | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
board/freescale/mx53loco/imximage.cfg +1 -1
index d1c1931..a5f1d98 100644
@@ -59,7 +59,7 @@ DATA 4 0x63fd9090 0x4d444c44
 DATA 4 0x63fd907c 0x01370138
 DATA 4 0x63fd9080 0x013b013c
 DATA 4 0x63fd9018 0x00011740
-DATA 4 0x63fd9000 0xc3190000
+DATA 4 0x63fd9000 0x83190000
 DATA 4 0x63fd900c 0x9f5152e3
 DATA 4 0x63fd9010 0xb68e8a63
 DATA 4 0x63fd9014 0x01ff00db

board/freescale/mx53loco/imximage.cfg DATA 4 0x63fd901c 0x00008033 · line 78

Quoted 7 lines
board/freescale/mx53loco/imximage.cfg +1 -0
@@ -72,6 +72,7 @@ DATA 4 0x63fd901c 0x00008033
 DATA 4 0x63fd901c 0x00028031
 DATA 4 0x63fd901c 0x052080b0
 DATA 4 0x63fd901c 0x04008040
+DATA 4 0x63fd9000 0xc3190000
 DATA 4 0x63fd901c 0x0000803a
 DATA 4 0x63fd901c 0x0000803b
 DATA 4 0x63fd901c 0x00028039

Good catch !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================