Skip to contentSkip to conversation

dmaengine: qcom_bam_dma: Add support for BAM v1.7.0

PATCH Superseded Archit Taneja 5 participants 8 messages Jan 22, 2015 – Mar 16, 2015

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 dmaengine: qcom_bam_dma: Add support for BAM v1.7.0

Add register offset table entry for the newer (v1.7.0) version of the BAM IP found on MSM8916. Update the DT bindings documentation.

---
 .../devicetree/bindings/dma/qcom_bam_dma.txt       |  1 +
 drivers/dma/qcom_bam_dma.c                         | 30 ++++++++++++++++++++++
 2 files changed, 31 insertions(+)
Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +1 -0
index f8c3311..1c9d48e 100644
@@ -4,6 +4,7 @@ Required properties:
 - compatible: must be one of the following:
  * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084
  * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960
+ * "qcom,bam-v1.7.0" for MSM8916
 - reg: Address range for DMA registers
 - interrupts: Should contain the one interrupt shared by all channels
 - #dma-cells: must be <1>, the cell in the dmas property of the client device
drivers/dma/qcom_bam_dma.c +30 -0
index 3122a99..447ad12 100644
@@ -171,6 +171,35 @@ static const struct reg_offset_data bam_v1_4_reg_info[] = {
 	[BAM_P_FIFO_SIZES]	= { 0x1820, 0x00, 0x1000, 0x00 },
 };
 
+static const struct reg_offset_data bam_v1_7_reg_info[] = {
+	[BAM_CTRL]		= { 0x00000, 0x00, 0x00, 0x00 },
+	[BAM_REVISION]		= { 0x01000, 0x00, 0x00, 0x00 },
+	[BAM_NUM_PIPES]		= { 0x01008, 0x00, 0x00, 0x00 },
+	[BAM_DESC_CNT_TRSHLD]	= { 0x00008, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS]		= { 0x03010, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_MSK]	= { 0x03014, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_UNMASKED]	= { 0x03018, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_STTS]		= { 0x00014, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_CLR]		= { 0x00018, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_EN]		= { 0x0001C, 0x00, 0x00, 0x00 },
+	[BAM_CNFG_BITS]		= { 0x0007C, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_EE]	= { 0x03000, 0x00, 0x00, 0x80 },
+	[BAM_IRQ_SRCS_MSK_EE]	= { 0x03004, 0x00, 0x00, 0x80 },
+	[BAM_P_CTRL]		= { 0x13000, 0x1000, 0x00, 0x00 },
+	[BAM_P_RST]		= { 0x13004, 0x1000, 0x00, 0x00 },
+	[BAM_P_HALT]		= { 0x13008, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_STTS]	= { 0x13010, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_CLR]		= { 0x13014, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_EN]		= { 0x13018, 0x1000, 0x00, 0x00 },
+	[BAM_P_EVNT_DEST_ADDR]	= { 0x1382C, 0x00, 0x1000, 0x00 },
+	[BAM_P_EVNT_REG]	= { 0x13818, 0x00, 0x1000, 0x00 },
+	[BAM_P_SW_OFSTS]	= { 0x13800, 0x00, 0x1000, 0x00 },
+	[BAM_P_DATA_FIFO_ADDR]	= { 0x13824, 0x00, 0x1000, 0x00 },
+	[BAM_P_DESC_FIFO_ADDR]	= { 0x1381C, 0x00, 0x1000, 0x00 },
+	[BAM_P_EVNT_GEN_TRSHLD]	= { 0x13828, 0x00, 0x1000, 0x00 },
+	[BAM_P_FIFO_SIZES]	= { 0x13820, 0x00, 0x1000, 0x00 },
+};
+
 /* BAM CTRL */
 #define BAM_SW_RST			BIT(0)
 #define BAM_EN				BIT(1)
@@ -1053,6 +1082,7 @@ static void bam_channel_init(struct bam_device *bdev, struct bam_chan *bchan,
 static const struct of_device_id bam_of_match[] = {
 	{ .compatible = "qcom,bam-v1.3.0", .data = &bam_v1_3_reg_info },
 	{ .compatible = "qcom,bam-v1.4.0", .data = &bam_v1_4_reg_info },
+	{ .compatible = "qcom,bam-v1.7.0", .data = &bam_v1_7_reg_info },
 	{}
 };
 
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
Reviewed-by on v1 1/1
#1 lore raw
Quoted 5 lines · Archit Taneja

Add register offset table entry for the newer (v1.7.0) version of the BAM IP found on MSM8916. Update the DT bindings documentation.

---

Looks good.

Signature · 3 lines
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
#3 lore raw
In reply to Archit Taneja
Quoted 33 lines · Archit Taneja

Add register offset table entry for the newer (v1.7.0) version of the BAM IP found on MSM8916. Update the DT bindings documentation.

---
 .../devicetree/bindings/dma/qcom_bam_dma.txt       |  1 +
 drivers/dma/qcom_bam_dma.c                         | 30 ++++++++++++++++++++++
 2 files changed, 31 insertions(+)
Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +1 -0
index f8c3311..1c9d48e 100644
@@ -4,6 +4,7 @@ Required properties:
 - compatible: must be one of the following:
  * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084
  * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960
+ * "qcom,bam-v1.7.0" for MSM8916
 - reg: Address range for DMA registers
 - interrupts: Should contain the one interrupt shared by all channels
 - #dma-cells: must be <1>, the cell in the dmas property of the client device
drivers/dma/qcom_bam_dma.c +4 -0
index 3122a99..447ad12 100644
@@ -171,6 +171,35 @@ static const struct reg_offset_data bam_v1_4_reg_info[] = {
 	[BAM_P_FIFO_SIZES]	= { 0x1820, 0x00, 0x1000, 0x00 },
 };
 
+static const struct reg_offset_data bam_v1_7_reg_info[] = {
+	[BAM_CTRL]		= { 0x00000, 0x00, 0x00, 0x00 },
+	[BAM_REVISION]		= { 0x01000, 0x00, 0x00, 0x00 },
+	[BAM_NUM_PIPES]		= { 0x01008, 0x00, 0x00, 0x00 },

drivers/dma/qcom_bam_dma.c static const struct reg_offset_data bam_v1_4_reg_info[] = { · line 187

Quoted 10 lines
drivers/dma/qcom_bam_dma.c +10 -0
+	[BAM_DESC_CNT_TRSHLD]	= { 0x00008, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS]		= { 0x03010, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_MSK]	= { 0x03014, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_UNMASKED]	= { 0x03018, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_STTS]		= { 0x00014, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_CLR]		= { 0x00018, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_EN]		= { 0x0001C, 0x00, 0x00, 0x00 },
+	[BAM_CNFG_BITS]		= { 0x0007C, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_EE]	= { 0x03000, 0x00, 0x00, 0x80 },
+	[BAM_IRQ_SRCS_MSK_EE]	= { 0x03004, 0x00, 0x00, 0x80 },

huh, 0x80 should be 0x1000 ?

Quoted 14 lines
drivers/dma/qcom_bam_dma.c +14 -0
+	[BAM_P_CTRL]		= { 0x13000, 0x1000, 0x00, 0x00 },
+	[BAM_P_RST]		= { 0x13004, 0x1000, 0x00, 0x00 },
+	[BAM_P_HALT]		= { 0x13008, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_STTS]	= { 0x13010, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_CLR]		= { 0x13014, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_EN]		= { 0x13018, 0x1000, 0x00, 0x00 },
+	[BAM_P_EVNT_DEST_ADDR]	= { 0x1382C, 0x00, 0x1000, 0x00 },
+	[BAM_P_EVNT_REG]	= { 0x13818, 0x00, 0x1000, 0x00 },
+	[BAM_P_SW_OFSTS]	= { 0x13800, 0x00, 0x1000, 0x00 },
+	[BAM_P_DATA_FIFO_ADDR]	= { 0x13824, 0x00, 0x1000, 0x00 },
+	[BAM_P_DESC_FIFO_ADDR]	= { 0x1381C, 0x00, 0x1000, 0x00 },
+	[BAM_P_EVNT_GEN_TRSHLD]	= { 0x13828, 0x00, 0x1000, 0x00 },
+	[BAM_P_FIFO_SIZES]	= { 0x13820, 0x00, 0x1000, 0x00 },
+};

<snip>

Signature · 2 lines
regards,
Stan
#4 lore raw

On Fri, Feb 20, 2015 at 01:57:29PM +0200, Stanimir Varbanov wrote:

<snip>

Quoted 6 lines

drivers/dma/qcom_bam_dma.c static const struct reg_offset_data bam_v1_4_reg_info[] = { · line 187

Quoted 4 lines
drivers/dma/qcom_bam_dma.c +4 -0
+	[BAM_IRQ_EN]		= { 0x0001C, 0x00, 0x00, 0x00 },
+	[BAM_CNFG_BITS]		= { 0x0007C, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_EE]	= { 0x03000, 0x00, 0x00, 0x80 },
+	[BAM_IRQ_SRCS_MSK_EE]	= { 0x03004, 0x00, 0x00, 0x80 },

huh, 0x80 should be 0x1000 ?

yeah the SRCS_EE and SRCS_MSK_EE should be 0x1000. good catch

<snip>

Signature · 3 lines
Qualcomm Innovation Center, Inc.
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
#5 lore raw

PATCH v2 1/1 dmaengine: qcom_bam_dma: Add support for BAM v1.7.0

In reply to Archit Taneja

Add register offset table entry for the newer (v1.7.0) version of the BAM IP found on MSM8916. Update the DT bindings documentation.

---
Change in v2: Fix wrong execution environment multiplier for BAM_IRQ_SRCS_EE and
BAM_IRQ_SRCS_MSK_EE

 .../devicetree/bindings/dma/qcom_bam_dma.txt       |  1 +
 drivers/dma/qcom_bam_dma.c                         | 30 ++++++++++++++++++++++
 2 files changed, 31 insertions(+)
Documentation/devicetree/bindings/dma/qcom_bam_dma.txt +1 -0
index f8c3311..1c9d48e 100644
@@ -4,6 +4,7 @@ Required properties:
 - compatible: must be one of the following:
  * "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084
  * "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960
+ * "qcom,bam-v1.7.0" for MSM8916
 - reg: Address range for DMA registers
 - interrupts: Should contain the one interrupt shared by all channels
 - #dma-cells: must be <1>, the cell in the dmas property of the client device
drivers/dma/qcom_bam_dma.c +30 -0
index d7a33b3..c737e6d 100644
@@ -171,6 +171,35 @@ static const struct reg_offset_data bam_v1_4_reg_info[] = {
 	[BAM_P_FIFO_SIZES]	= { 0x1820, 0x00, 0x1000, 0x00 },
 };
 
+static const struct reg_offset_data bam_v1_7_reg_info[] = {
+	[BAM_CTRL]		= { 0x00000, 0x00, 0x00, 0x00 },
+	[BAM_REVISION]		= { 0x01000, 0x00, 0x00, 0x00 },
+	[BAM_NUM_PIPES]		= { 0x01008, 0x00, 0x00, 0x00 },
+	[BAM_DESC_CNT_TRSHLD]	= { 0x00008, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS]		= { 0x03010, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_MSK]	= { 0x03014, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_UNMASKED]	= { 0x03018, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_STTS]		= { 0x00014, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_CLR]		= { 0x00018, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_EN]		= { 0x0001C, 0x00, 0x00, 0x00 },
+	[BAM_CNFG_BITS]		= { 0x0007C, 0x00, 0x00, 0x00 },
+	[BAM_IRQ_SRCS_EE]	= { 0x03000, 0x00, 0x00, 0x1000 },
+	[BAM_IRQ_SRCS_MSK_EE]	= { 0x03004, 0x00, 0x00, 0x1000 },
+	[BAM_P_CTRL]		= { 0x13000, 0x1000, 0x00, 0x00 },
+	[BAM_P_RST]		= { 0x13004, 0x1000, 0x00, 0x00 },
+	[BAM_P_HALT]		= { 0x13008, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_STTS]	= { 0x13010, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_CLR]		= { 0x13014, 0x1000, 0x00, 0x00 },
+	[BAM_P_IRQ_EN]		= { 0x13018, 0x1000, 0x00, 0x00 },
+	[BAM_P_EVNT_DEST_ADDR]	= { 0x1382C, 0x00, 0x1000, 0x00 },
+	[BAM_P_EVNT_REG]	= { 0x13818, 0x00, 0x1000, 0x00 },
+	[BAM_P_SW_OFSTS]	= { 0x13800, 0x00, 0x1000, 0x00 },
+	[BAM_P_DATA_FIFO_ADDR]	= { 0x13824, 0x00, 0x1000, 0x00 },
+	[BAM_P_DESC_FIFO_ADDR]	= { 0x1381C, 0x00, 0x1000, 0x00 },
+	[BAM_P_EVNT_GEN_TRSHLD]	= { 0x13828, 0x00, 0x1000, 0x00 },
+	[BAM_P_FIFO_SIZES]	= { 0x13820, 0x00, 0x1000, 0x00 },
+};
+
 /* BAM CTRL */
 #define BAM_SW_RST			BIT(0)
 #define BAM_EN				BIT(1)
@@ -1051,6 +1080,7 @@ static void bam_channel_init(struct bam_device *bdev, struct bam_chan *bchan,
 static const struct of_device_id bam_of_match[] = {
 	{ .compatible = "qcom,bam-v1.3.0", .data = &bam_v1_3_reg_info },
 	{ .compatible = "qcom,bam-v1.4.0", .data = &bam_v1_4_reg_info },
+	{ .compatible = "qcom,bam-v1.7.0", .data = &bam_v1_7_reg_info },
 	{}
 };
 
Signature · 2 lines
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
Tested-by on v2 1/1
#6 lore raw
Quoted 11 lines · Archit Taneja

Add register offset table entry for the newer (v1.7.0) version of the BAM IP found on MSM8916. Update the DT bindings documentation.

---
Change in v2: Fix wrong execution environment multiplier for BAM_IRQ_SRCS_EE and
BAM_IRQ_SRCS_MSK_EE

 .../devicetree/bindings/dma/qcom_bam_dma.txt       |  1 +
 drivers/dma/qcom_bam_dma.c                         | 30 ++++++++++++++++++++++
 2 files changed, 31 insertions(+)

Using Stan's SPI DMA patches[1].

Thanks,
Ivan

[1] https://lkml.org/lkml/2015/3/4/621

Applied
#7 lore raw
In reply to Archit Taneja
Quoted 3 lines · Archit Taneja

Add register offset table entry for the newer (v1.7.0) version of the BAM IP found on MSM8916. Update the DT bindings documentation.

Applied, thanks

Signature · 1 line
~Vinod