ARM: dts: qcom: label all gsbi devices
PATCH 1/2 ARM: dts: qcom: label all gsbi devices
All IPQ806x based boards will include this file and will need a way to identify each GSBI device. So this change is labelling them all to make reference from board specific file easier.
Signed-off-by Mathieu Olivari <[email protected]>
--- arch/arm/boot/dts/qcom-ipq8064.dtsi | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
arch/arm/boot/dts/qcom-ipq8064.dtsi +7 -7
@@ -140,7 +140,7 @@ ranges; status = "disabled"; - serial at 12490000 { + uart2: serial at 12490000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x12490000 0x1000>, <0x12480000 0x1000>;
@@ -150,7 +150,7 @@ status = "disabled"; }; - i2c at 124a0000 { + i2c2: i2c at 124a0000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x124a0000 0x1000>; interrupts = <0 196 0>;
@@ -175,7 +175,7 @@ ranges; status = "disabled"; - serial at 16340000 { + uart4: serial at 16340000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16340000 0x1000>, <0x16300000 0x1000>;
@@ -185,7 +185,7 @@ status = "disabled"; }; - i2c at 16380000 { + i2c4: i2c at 16380000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x16380000 0x1000>; interrupts = <0 153 0>;
@@ -209,7 +209,7 @@ ranges; status = "disabled"; - serial at 1a240000 { + uart5: serial at 1a240000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x1a240000 0x1000>, <0x1a200000 0x1000>;
@@ -219,7 +219,7 @@ status = "disabled"; }; - i2c at 1a280000 { + i2c5: i2c at 1a280000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x1a280000 0x1000>; interrupts = <0 155 0>;
@@ -232,7 +232,7 @@ #size-cells = <0>; }; - spi at 1a280000 { + spi5: spi at 1a280000 { compatible = "qcom,spi-qup-v1.1.1"; reg = <0x1a280000 0x1000>; interrupts = <0 155 0>;
Signature · 1 line
1.9.1
PATCH 2/2 ARM: dts: qcom: add stdout-path to AP148
AP148 default console output is uart4, so this change adds a serial0 alias to it, as well add the corresponding stdout-path.
This will avoid having to set these as chosen.
Signed-off-by Mathieu Olivari <[email protected]>
--- arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm/boot/dts/qcom-ipq8064-ap148.dts +8 -0
@@ -14,6 +14,14 @@ }; }; + alias { + serial0 = &uart4; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + soc { pinmux at 800000 { i2c4_pins: i2c4_pinmux {
Signature · 1 line
1.9.1