Skip to contentSkip to conversation

bnx2: disable toggling of rxvlan if necessary

PATCH Applied Ivan Vecera 2 participants 3 messages Feb 26, 2015 – Mar 2, 2015

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 bnx2: disable toggling of rxvlan if necessary

The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag stripping when the card cannot disable it. The driver should remove NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed for the ethtool.

---
 drivers/net/ethernet/broadcom/bnx2.c | 15 +++------------
 1 file changed, 3 insertions(+), 12 deletions(-)
drivers/net/ethernet/broadcom/bnx2.c +3 -12
index 9f146b9..2b66ef3 100644
@@ -7708,17 +7708,6 @@ bnx2_set_phys_id(struct net_device *dev, enum ethtool_phys_id_state state)
 	return 0;
 }
 
-static netdev_features_t
-bnx2_fix_features(struct net_device *dev, netdev_features_t features)
-{
-	struct bnx2 *bp = netdev_priv(dev);
-
-	if (!(bp->flags & BNX2_FLAG_CAN_KEEP_VLAN))
-		features |= NETIF_F_HW_VLAN_CTAG_RX;
-
-	return features;
-}
-
 static int
 bnx2_set_features(struct net_device *dev, netdev_features_t features)
 {
@@ -8525,7 +8514,6 @@ static const struct net_device_ops bnx2_netdev_ops = {
 	.ndo_validate_addr	= eth_validate_addr,
 	.ndo_set_mac_address	= bnx2_change_mac_addr,
 	.ndo_change_mtu		= bnx2_change_mtu,
-	.ndo_fix_features	= bnx2_fix_features,
 	.ndo_set_features	= bnx2_set_features,
 	.ndo_tx_timeout		= bnx2_tx_timeout,
 #ifdef CONFIG_NET_POLL_CONTROLLER
@@ -8576,6 +8564,9 @@ bnx2_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	dev->features |= dev->hw_features;
 	dev->priv_flags |= IFF_UNICAST_FLT;
 
+	if (!(bp->flags & BNX2_FLAG_CAN_KEEP_VLAN))
+		dev->hw_features &= ~NETIF_F_HW_VLAN_CTAG_RX;
+
 	if ((rc = register_netdev(dev))) {
 		dev_err(&pdev->dev, "Cannot register net device\n");
 		goto error;
Signature · 1 line
2.0.5
maintainer
#1 lore raw

From: Ivan Vecera <[email protected]>
Date: Thu, 26 Feb 2015 14:48:07 +0100

Quoted 8 lines

The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag stripping when the card cannot disable it. The driver should remove NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed for the ethtool.

Would be great to get some reviews from the qlogic folks.

maintainer Applied
#2 lore raw
In reply to Ivan Vecera

From: Ivan Vecera <[email protected]>
Date: Thu, 26 Feb 2015 14:48:07 +0100

Quoted 8 lines

The bnx2 driver uses .ndo_fix_features to force enable of Rx VLAN tag stripping when the card cannot disable it. The driver should remove NETIF_F_HW_VLAN_CTAG_RX flag from hw_features instead so it is fixed for the ethtool.

Applied, thanks.