Add pinctrl support to Broadcom Cygnus SoC

index ee9f44a..1a9143d 100644
@@ -67,24 +67,6 @@ config PINCTRL_AT91
 	help
 	  Say Y here to enable the at91 pinctrl driver
 
-config PINCTRL_BCM2835
-	bool
-	select PINMUX
-	select PINCONF
-
-config PINCTRL_BCM281XX
-	bool "Broadcom BCM281xx pinctrl driver"
-	depends on OF && (ARCH_BCM_MOBILE || COMPILE_TEST)
-	select PINMUX
-	select PINCONF
-	select GENERIC_PINCONF
-	select REGMAP_MMIO
-	help
-	  Say Y here to support Broadcom BCM281xx pinctrl driver, which is used
-	  for the BCM281xx SoC family, including BCM11130, BCM11140, BCM11351,
-	  BCM28145, and BCM28155 SoCs.  This driver requires the pinctrl
-	  framework.  GPIO is provided by a separate GPIO driver.
-
 config PINCTRL_LANTIQ
 	bool
 	depends on LANTIQ

@@ -207,6 +189,7 @@ config PINCTRL_ZYNQ
 	help
 	  This selectes the pinctrl driver for Xilinx Zynq.
 
+source "drivers/pinctrl/bcm/Kconfig"
 source "drivers/pinctrl/berlin/Kconfig"
 source "drivers/pinctrl/freescale/Kconfig"
 source "drivers/pinctrl/intel/Kconfig"

index 0475206..c14ce05 100644
@@ -14,8 +14,6 @@ obj-$(CONFIG_PINCTRL_AS3722)	+= pinctrl-as3722.o
 obj-$(CONFIG_PINCTRL_BF54x)	+= pinctrl-adi2-bf54x.o
 obj-$(CONFIG_PINCTRL_BF60x)	+= pinctrl-adi2-bf60x.o
 obj-$(CONFIG_PINCTRL_AT91)	+= pinctrl-at91.o
-obj-$(CONFIG_PINCTRL_BCM2835)	+= pinctrl-bcm2835.o
-obj-$(CONFIG_PINCTRL_BCM281XX)	+= pinctrl-bcm281xx.o
 obj-$(CONFIG_PINCTRL_FALCON)	+= pinctrl-falcon.o
 obj-$(CONFIG_PINCTRL_MESON)	+= meson/
 obj-$(CONFIG_PINCTRL_PALMAS)	+= pinctrl-palmas.o

@@ -38,6 +36,7 @@ obj-$(CONFIG_PINCTRL_TB10X)	+= pinctrl-tb10x.o
 obj-$(CONFIG_PINCTRL_ST) 	+= pinctrl-st.o
 obj-$(CONFIG_PINCTRL_ZYNQ)	+= pinctrl-zynq.o
 
+obj-$(CONFIG_ARCH_BCM)		+= bcm/
 obj-$(CONFIG_ARCH_BERLIN)	+= berlin/
 obj-y				+= freescale/
 obj-$(CONFIG_X86)		+= intel/

new file mode 100644
index 0000000..bc6d048
@@ -0,0 +1,21 @@
+#
+# Broadcom pinctrl drivers
+#
+
+config PINCTRL_BCM281XX
+	bool "Broadcom BCM281xx pinctrl driver"
+	depends on OF && (ARCH_BCM_MOBILE || COMPILE_TEST)
+	select PINMUX
+	select PINCONF
+	select GENERIC_PINCONF
+	select REGMAP_MMIO
+	help
+	  Say Y here to support Broadcom BCM281xx pinctrl driver, which is used
+	  for the BCM281xx SoC family, including BCM11130, BCM11140, BCM11351,
+	  BCM28145, and BCM28155 SoCs.  This driver requires the pinctrl
+	  framework.  GPIO is provided by a separate GPIO driver.
+
+config PINCTRL_BCM2835
+	bool
+	select PINMUX
+	select PINCONF

new file mode 100644
index 0000000..7ba80a3
@@ -0,0 +1,4 @@
+# Broadcom pinctrl support
+
+obj-$(CONFIG_PINCTRL_BCM281XX)	+= pinctrl-bcm281xx.o
+obj-$(CONFIG_PINCTRL_BCM2835)	+= pinctrl-bcm2835.o

new file mode 100644
index 0000000..3600d5c
@@ -0,0 +1,132 @@
+Broadcom Cygnus IOMUX Controller
+
+The Cygnus IOMUX controller supports group based mux configuration. In
+addition, certain pins can be muxed to GPIO function individually.
+
+Required properties:
+
+- compatible:
+    Must be "brcm,cygnus-pinmux"
+
+- reg:
+    Define the base and range of the I/O address space that contains the Cygnus
+IOMUX registers
+
+Properties in subnodes:
+
+- function:
+    The mux function to select
+
+- groups:
+    The list of groups to select with a given function
+
+For more details, refer to
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+For example:
+
+	pinmux: pinmux@0x0301d0c8 {
+		compatible = "brcm,cygnus-pinmux";
+		reg = <0x0301d0c8 0x1b0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s0_default>;
+
+		i2s0_default: i2s0_default {
+			mux {
+				function = "i2s0";
+				groups = "i2s0_0_grp", "i2s0_1_grp";
+			};
+		};
+	};
+
+List of supported functions and groups in Cygnus:
+
+"i2s0": "i2s0_0_grp", "i2s0_1_grp"
+
+"i2s1": "i2s1_0_grp", "i2s1_1_grp"
+
+"i2s2": "i2s2_0_grp", "i2s2_1_grp", "i2s2_2_grp", "i2s2_3_grp", "i2s2_4_grp"
+
+"spdif": "spdif_grp"
+
+"pwm0": "pwm0_grp"
+
+"pwm1": "pwm1_grp"
+
+"pwm2": "pwm2_grp"
+
+"pwm3": "pwm3_grp"
+
+"pwm4": "pwm4_grp"
+
+"pwm5": "pwm5_grp"
+
+"key": "key0_grp", "key1_grp", "key2_grp", "key3_grp", "key4_grp", "key5_grp",
+"key6_grp", "key7_grp", "key8_grp", "key9_grp", "key10_grp", "key11_grp",
+"key12_grp", "key13_grp", "key14_grp", "key15_grp"
+
+"audio_dte": "audio_dte0_grp", "audio_dte1_grp", "audio_dte2_grp", "audio_dte3_grp"
+
+"smart_card0": "smart_card0_grp", "smart_card0_fcb_grp"
+
+"smart_card1": "smart_card1_grp", "smart_card1_fcb_grp"
+
+"spi0": "spi0_grp"
+
+"spi1": "spi1_grp"
+
+"spi2": "spi2_grp"
+
+"spi3": "spi3_grp"
+
+"spi4": "spi4_0_grp", "spi4_1_grp"
+
+"spi5": "spi5_grp"
+
+"sw_led0": "sw_led0_0_grp", "sw_led0_1_grp"
+
+"sw_led1": "sw_led1_grp"
+
+"sw_led2": "sw_led2_0_grp", "sw_led2_1_grp"
+
+"d1w": "d1w_grp"
+
+"lcd": "lcd_grp"
+
+"sram": "sram_0_grp", "sram_1_grp"
+
+"uart0": "uart0_grp"
+
+"uart1": "uart1_grp", "uart1_dte_grp"
+
+"uart2": "uart2_grp"
+
+"uart3": "uart3_grp"
+
+"uart4": "uart4_grp"
+
+"qspi": "qspi_0_grp", "qspi_1_grp"
+
+"nand": "nand_grp"
+
+"sdio0": "sdio0_grp", "sdio0_cd_grp", "sdio0_mmc_grp"
+
+"sdio1": "sdio1_data_0_grp", "sdio1_data_1_grp", "sdio1_cd_grp",
+"sdio1_led_grp", "sdio1_mmc_grp"
+
+"can0": "can0_grp"
+
+"can1": "can1_grp"
+
+"cam": "cam_led_grp", "cam_0_grp", "cam_1_grp"
+
+"bsc1": "bsc1_grp"
+
+"pcie_clkreq": "pcie_clkreq_grp"
+
+"usb0_oc": "usb0_oc_grp"
+
+"usb1_oc": "usb1_oc_grp"
+
+"usb2_oc": "usb2_oc_grp"

index bc6d048..eb13201 100644
@@ -19,3 +19,16 @@ config PINCTRL_BCM2835
 	bool
 	select PINMUX
 	select PINCONF
+
+config PINCTRL_CYGNUS_MUX
+	bool "Broadcom Cygnus IOMUX driver"
+	depends on (ARCH_BCM_CYGNUS || COMPILE_TEST)
+	select PINMUX
+	select GENERIC_PINCONF
+	default ARCH_BCM_CYGNUS
+	help
+	  Say yes here to enable the Broadcom Cygnus IOMUX driver.
+
+	  The Broadcom Cygnus IOMUX driver supports group based IOMUX
+	  configuration, with the exception that certain individual pins
+	  can be overrided to GPIO function

index 7ba80a3..bb6beb6 100644
@@ -1,4 +1,5 @@
 # Broadcom pinctrl support
 
-obj-$(CONFIG_PINCTRL_BCM281XX)	+= pinctrl-bcm281xx.o
-obj-$(CONFIG_PINCTRL_BCM2835)	+= pinctrl-bcm2835.o
+obj-$(CONFIG_PINCTRL_BCM281XX)		+= pinctrl-bcm281xx.o
+obj-$(CONFIG_PINCTRL_BCM2835)		+= pinctrl-bcm2835.o
+obj-$(CONFIG_PINCTRL_CYGNUS_MUX)	+= pinctrl-cygnus-mux.o

index ff5fb6a..1cbae6a 100644
@@ -54,6 +54,12 @@
 
 	/include/ "bcm-cygnus-clock.dtsi"
 
+	pinctrl: pinctrl@0x0301d0c8 {
+		compatible = "brcm,cygnus-pinmux";
+		reg = <0x0301d0c8 0x30>,
+		      <0x0301d24c 0x2c>;
+	};
+
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;

new file mode 100644
index 0000000..6540ca5
@@ -0,0 +1,98 @@
+Broadcom Cygnus GPIO/PINCONF Controller
+
+Required properties:
+
+- compatible:
+    Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or
+    "brcm,cygnus-crmu-gpio"
+
+- reg:
+    Define the base and range of the I/O address space that contains the Cygnus
+GPIO/PINCONF controller registers
+
+- #gpio-cells:
+    Must be two. The first cell is the GPIO pin number (within the
+controller's pin space) and the second cell is used for the following:
+    bit[0]: polarity (0 for active high and 1 for active low)
+
+- gpio-controller:
+    Specifies that the node is a GPIO controller
+
+Optional properties:
+
+- interrupts:
+    Interrupt ID
+
+- interrupt-controller:
+    Specifies that the node is an interrupt controller
+
+- pinmux:
+    Specifies the phandle to the IOMUX device, where pins can be individually
+muxed to GPIO
+
+Supported generic PINCONF properties in child nodes:
+
+- pins:
+    The list of pins (within the controller's own pin space) that properties
+in the node apply to. Pin names are "gpio-<pin>"
+
+- bias-disable:
+    Disable pin bias
+
+- bias-pull-up:
+    Enable internal pull up resistor
+
+- bias-pull-down:
+    Enable internal pull down resistor
+
+- drive-strength:
+    Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA)
+
+Example:
+	gpio_ccm: gpio@1800a000 {
+		compatible = "brcm,cygnus-ccm-gpio";
+		reg = <0x1800a000 0x50>,
+		      <0x0301d164 0x20>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+
+		touch_pins: touch_pins {
+			pwr: pwr {
+				pins = "gpio-0";
+				drive-strength = <16>;
+			};
+
+			event: event {
+				pins = "gpio-1";
+				bias-pull-up;
+			};
+		};
+	};
+
+	gpio_asiu: gpio@180a5000 {
+		compatible = "brcm,cygnus-asiu-gpio";
+		reg = <0x180a5000 0x668>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+	};
+
+	/*
+	 * Touchscreen that uses the CCM GPIO 0 and 1
+	 */
+	tsc {
+		...
+		...
+		gpio-pwr = <&gpio_ccm 0 0>;
+		gpio-event = <&gpio_ccm 1 0>;
+	};
+
+	/* Bluetooth that uses the ASIU GPIO 5, with polarity inverted */
+	bluetooth {
+		...
+		...
+		bcm,rfkill-bank-sel = <&gpio_asiu 5 1>
+	}

index eb13201..cd11d4d 100644
@@ -20,6 +20,28 @@ config PINCTRL_BCM2835
 	select PINMUX
 	select PINCONF
 
+config PINCTRL_CYGNUS_GPIO
+	bool "Broadcom Cygnus GPIO (with PINCONF) driver"
+	depends on OF_GPIO && ARCH_BCM_CYGNUS
+	select GPIOLIB_IRQCHIP
+	select PINCONF
+	select GENERIC_PINCONF
+	default ARCH_BCM_CYGNUS
+	help
+	  Say yes here to enable the Broadcom Cygnus GPIO driver.
+
+	  The Broadcom Cygnus SoC has 3 GPIO controllers including the ASIU
+	  GPIO controller (ASIU), the chipCommonG GPIO controller (CCM), and
+	  the always-ON GPIO controller (CRMU/AON). All 3 GPIO controllers are
+	  supported by this driver.
+
+	  All 3 Cygnus GPIO controllers support basic PINCONF functions such
+	  as bias pull up, pull down, and drive strength configurations, when
+	  these pins are muxed to GPIO.
+
+	  Pins from the ASIU GPIO can be individually muxed to GPIO function,
+	  through interaction with the Cygnus IOMUX controller.
+
 config PINCTRL_CYGNUS_MUX
 	bool "Broadcom Cygnus IOMUX driver"
 	depends on (ARCH_BCM_CYGNUS || COMPILE_TEST)

index bb6beb6..2b2f70e 100644
@@ -2,4 +2,5 @@
 
 obj-$(CONFIG_PINCTRL_BCM281XX)		+= pinctrl-bcm281xx.o
 obj-$(CONFIG_PINCTRL_BCM2835)		+= pinctrl-bcm2835.o
+obj-$(CONFIG_PINCTRL_CYGNUS_GPIO)	+= pinctrl-cygnus-gpio.o
 obj-$(CONFIG_PINCTRL_CYGNUS_MUX)	+= pinctrl-cygnus-mux.o

index 1cbae6a..63b7fed 100644
@@ -60,6 +60,36 @@
 		      <0x0301d24c 0x2c>;
 	};
 
+	gpio_crmu: gpio@03024800 {
+		compatible = "brcm,cygnus-crmu-gpio";
+		reg = <0x03024800 0x50>,
+		      <0x03024008 0x18>;
+		#gpio-cells = <2>;
+		gpio-controller;
+	};
+
+	gpio_ccm: gpio@1800a000 {
+		compatible = "brcm,cygnus-ccm-gpio";
+		reg = <0x1800a000 0x50>,
+		      <0x0301d164 0x20>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+	};
+
+	gpio_asiu: gpio@180a5000 {
+		compatible = "brcm,cygnus-asiu-gpio";
+		reg = <0x180a5000 0x668>;
+		#gpio-cells = <2>;
+		gpio-controller;
+
+		pinmux = <&pinctrl>;
+
+		interrupt-controller;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;

index d2ee952..7db4843 100644
@@ -33,6 +33,7 @@
 /dts-v1/;
 
 #include "bcm-cygnus.dtsi"
+#include "dt-bindings/input/input.h"
 
 / {
 	model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)";

@@ -50,4 +51,16 @@
 	uart3: serial@18023000 {
 		status = "okay";
 	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hook {
+			label = "HOOK";
+			linux,code = <KEY_O>;
+			gpios = <&gpio_asiu 48 0>;
+		};
+	};
 };