boot/uboot: add support for i.MX28 SD format

index 03e6acc..cea993a 100644
@@ -117,6 +117,18 @@ config BR2_TARGET_UBOOT_FORMAT_SB
 	depends on BR2_arm
 	bool "u-boot.sb"
 
+config BR2_TARGET_UBOOT_FORMAT_SD
+	depends on BR2_arm
+	bool "u-boot.sd"
+	help
+	  This is Freescale i.MX28 SB format, with a header for booting from an
+	  SD card.
+
+	  U-boot includes an mxsboot tool to generate this format, starting
+	  from v2011.12.
+
+	  See doc/README.mxs.
+
 config BR2_TARGET_UBOOT_FORMAT_CUSTOM
 	bool "Custom (specify below)"
 	help

index a9ba054..8fad5b4 100644
@@ -49,6 +49,9 @@ else ifeq ($(BR2_TARGET_UBOOT_FORMAT_SB),y)
 UBOOT_BIN = u-boot.sb
 UBOOT_MAKE_TARGET = $(UBOOT_BIN)
 UBOOT_DEPENDENCIES += host-elftosb
+else ifeq ($(BR2_TARGET_UBOOT_FORMAT_SD),y)
+UBOOT_BIN = u-boot.sd
+UBOOT_MAKE_TARGET = u-boot.sb
 else ifeq ($(BR2_TARGET_UBOOT_FORMAT_CUSTOM),y)
 UBOOT_BIN = $(call qstrip,$(BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME))
 else

@@ -116,6 +119,8 @@ define UBOOT_BUILD_CMDS
 	$(TARGET_CONFIGURE_OPTS) 	\
 		$(MAKE) -C $(@D) $(UBOOT_MAKE_OPTS) 		\
 		$(UBOOT_MAKE_TARGET)
+	$(if $(BR2_TARGET_UBOOT_FORMAT_SD),
+		$(@D)/tools/mxsboot sd $(@D)/u-boot.sb $(@D)/u-boot.sd)
 endef
 
 define UBOOT_BUILD_OMAP_IFT

new file mode 100755
index 0000000..5e050cb
@@ -0,0 +1,97 @@
+#!/bin/sh
+
+set -u
+set -e
+
+PROGNAME=$(basename $0)
+
+usage()
+{
+    echo "Create an SD card that boots on an i.MX28 EVK board."
+    echo
+    echo "Note: all data on the the card will be completely deleted!"
+    echo "Use with care!"
+    echo "Superuser permissions may be required to write to the device."
+    echo
+    echo "Usage: ${PROGNAME} <sd_block_device>"
+    echo "Arguments:"
+    echo "  <sd_block_device>     The device to be written to"
+    echo
+    echo "Example: ${PROGNAME} /dev/mmcblk0"
+    echo
+}
+
+if [ $# -ne 1 ]; then
+    usage
+    exit 1
+fi
+
+if [ $(id -u) -ne 0 ]; then
+    echo "${PROGNAME} must be run as root"
+    exit 1
+fi
+
+DEV=${1}
+
+# The partition name prefix depends on the device name:
+# - /dev/sde -> /dev/sde1
+# - /dev/mmcblk0 -> /dev/mmcblk0p1
+if echo ${DEV}|grep -q mmcblk ; then
+    PART="p"
+else
+    PART=""
+fi
+
+PART1=${DEV}${PART}1
+PART2=${DEV}${PART}2
+PART3=${DEV}${PART}3
+
+# Unmount the partitions if mounted
+umount ${PART1} || true
+umount ${PART2} || true
+umount ${PART3} || true
+
+# First, clear the card
+dd if=/dev/zero of=${DEV} bs=1M count=20
+
+sync
+
+# Partition the card.
+# SD layout for i.MX28 boot:
+# - Special partition type 53 at sector 2048, containing an SD-SB-encapsulated u-boot
+# - FAT partition containing zImage
+# - ext2/3 partition formatted as ext2 or ext3, containing the root filesystem.
+sfdisk --force -u S ${DEV} <<EOF
+2048,2000,53
+4048,16000,b
+20048,,L
+EOF
+
+sync
+
+# Copy the bootloader@offset 2048
+# (We need to skip the partition table in the .sd, too.)
+dd if=output/images/u-boot.sd of=${DEV}1 bs=1M
+
+# Prepare a temp dir for mounting partitions
+TMPDIR=$(mktemp -d)
+ 
+# FAT partition: kernel
+mkfs.vfat ${PART2}
+mount ${PART2} ${TMPDIR}
+cp output/images/*Image ${TMPDIR}/
+cp output/images/*.dtb  ${TMPDIR}/ || true
+sync
+umount ${TMPDIR}
+
+# ext2 partition: root filesystem
+mkfs.ext2 ${PART3}
+mount ${PART3} ${TMPDIR}
+tar -C ${TMPDIR}/ -xf output/images/rootfs.tar
+sync
+umount ${TMPDIR}
+
+# Cleanup
+rmdir ${TMPDIR}
+sync
+echo Done

58 lines not on this page · raw message

new file mode 100644
index 0000000..15cedeb
@@ -0,0 +1,18 @@
+# architecture
+BR2_arm=y
+BR2_arm926t=y
+
+# system
+BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA0"
+
+# kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_DEFCONFIG="mxs"
+BR2_LINUX_KERNEL_ZIMAGE=y
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx28-evk"
+
+# bootloader
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BOARDNAME="mx28evk"
+BR2_TARGET_UBOOT_FORMAT_SD=y