Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
A message that is not in the archive (sent off-list or not yet received): [email protected]
Dear All,
Could you please provide any inputs w.r.t the loopback card using snd-aloop & alsaloop, how this loopback card can be used to connect the GSM two way call simultanoeusly to the UDA1345TS codec on MCASP0 of the am335x (UDA1345TS ie., real sound card)
The codec has two output channels VOUTL, VOUTR & two input channels VINL , VINR
As I am pretty new to linux audio particularly ALSA Framework as I was involved only in intial codec bringup using aplay & arecord utilities , as I was having some trouble getting a grasp on it all, (as I want this to be darecord one in ALSA only without entering into gstreamer or ffmpeg, could you please confirm on the same that whether can it be done in ALSA only)
If this probably isn't the place to ask this question, but I am not sure where is. Feel free to point me somewhere else if there is a better place :)
So it seems what is happening is basically when i up the channels from VINL to VOUTL, & VINR to VOUTR ie., I am able capture from VINR & play back using VOUTR & similarly I am able to capture from VINR & route to VOUTR using the below asound.conf & the attached application
With this am able to achieve only one way call at a time by running only one application at a time ie., alsa_loopback_min_mono_VINL.c or alsa_loopback_min_mono_VINR.c
Could you please kindly let me know how two way call can be established simultaneously finally with only one application , as I tried merging both apps ie., (alsa_loopback_min_mono_VINL & alsa_loopback_min_mono_VINR) at that moment am getting device resource busy, when I tried to open snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0) in the application alsa_loopback_min_mono.c
Kindly do the needful as early as possible,
Awaiting for your replies,
Many Many Thanks a lot for your replies & would appreciate the same w.r.t my earlier two queries
#include <stdio.h>
#include <stdlib.h>
#include <alsa/asoundlib.h>
#define BUF_BYTES 128
int main (/*int argc, char *argv[]*/) {
int err;
unsigned char buf_right[BUF_BYTES];
unsigned char buf_left[BUF_BYTES];
//char *buf;
int size;
snd_pcm_t *playback_handle_right;
snd_pcm_t *capture_handle_right;
snd_pcm_t *playback_handle_left;
snd_pcm_t *capture_handle_left;#if 0 char* device = "default"; if (argc > 1) device = argv[1]; #endif char* crdevice = "VINR"; char* prdevice = "VOUTR"; char* cldevice = "VINL"; char* pldevice = "VOUTL"; unsigned int rate = 48000; unsigned int nchannels = 1; snd_pcm_format_t format = SND_PCM_FORMAT_S16_LE; unsigned int buf_frames_right = BUF_BYTES / nchannels / 2; unsigned int buf_frames_left = BUF_BYTES / nchannels / 2;
///// RIGHT CHANNEL
if ((err = snd_pcm_open (&playback_handle_right, prdevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback right audio device %s (%s)\n", prdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback right audio device successfully %s \n", prdevice);
}
if ((err = snd_pcm_set_params(playback_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback right open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_right, crdevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture right audio device %s (%s)\n", crdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture right audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture right open error: %s\n", snd_strerror(err)); exit(1);
} ////LEFT CHANNEL
if ((err = snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback left audio device %s (%s)\n", pldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback left audio device successfully %s \n", pldevice);
}
if ((err = snd_pcm_set_params(playback_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback left open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_left, cldevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture left audio device %s (%s)\n", cldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture left audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture left open error: %s\n", snd_strerror(err)); exit(1);
}
while(1) {
///// RIGHT CHANNEL
if ((err = snd_pcm_readi (capture_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
////LEFT CHANNEL
if ((err = snd_pcm_readi (capture_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "read from audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "write to audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
}
fprintf (stderr, "close handles\n");
snd_pcm_close (playback_handle_right);
snd_pcm_close (capture_handle_right);
snd_pcm_close (playback_handle_left);
snd_pcm_close (capture_handle_left);
return 0;
} #include <stdio.h>
#include <stdlib.h>
#include <alsa/asoundlib.h>
#define BUF_BYTES 128
int main (/*int argc, char *argv[]*/) {
int err;
unsigned char buf_right[BUF_BYTES];
unsigned char buf_left[BUF_BYTES];
//char *buf;
int size;// snd_pcm_t *playback_handle_right;
// snd_pcm_t *capture_handle_right; snd_pcm_t *playback_handle_left; snd_pcm_t *capture_handle_left;
#if 0 char* device = "default"; if (argc > 1) device = argv[1];
#endif
// char* crdevice = "VINR";
// char* prdevice = "VOUTR";
char* cldevice = "VINL";
char* pldevice = "VOUTL";
unsigned int rate = 48000;
unsigned int nchannels = 1;
snd_pcm_format_t format = SND_PCM_FORMAT_S16_LE;
// unsigned int buf_frames_right = BUF_BYTES / nchannels / 2;
unsigned int buf_frames_left = BUF_BYTES / nchannels / 2;
#if 0
///// RIGHT CHANNEL
if ((err = snd_pcm_open (&playback_handle_right, prdevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback right audio device %s (%s)\n", prdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback right audio device successfully %s \n", prdevice);
}
if ((err = snd_pcm_set_params(playback_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback right open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_right, crdevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture right audio device %s (%s)\n", crdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture right audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture right open error: %s\n", snd_strerror(err)); exit(1);
}
#endif
////LEFT CHANNEL
if ((err = snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback left audio device %s (%s)\n", pldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback left audio device successfully %s \n", pldevice);
}
if ((err = snd_pcm_set_params(playback_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback left open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_left, cldevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture left audio device %s (%s)\n", cldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture left audio device successfully %s \n", cldevice);
}
if ((err = snd_pcm_set_params(capture_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture left open error: %s\n", snd_strerror(err)); exit(1);
}
while(1) {
#if 0
///// RIGHT CHANNEL
if ((err = snd_pcm_readi (capture_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
#endif
////LEFT CHANNEL
if ((err = snd_pcm_readi (capture_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "read from audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "write to audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
}
fprintf (stderr, "close handles\n");// snd_pcm_close (playback_handle_right);
// snd_pcm_close (capture_handle_right);
snd_pcm_close (playback_handle_left); snd_pcm_close (capture_handle_left); return 0; }
#include <stdio.h>
#include <stdlib.h>
#include <alsa/asoundlib.h>
#define BUF_BYTES 128
int main (/*int argc, char *argv[]*/) {
int err;
unsigned char buf_right[BUF_BYTES];
unsigned char buf_left[BUF_BYTES];
//char *buf;
int size;
snd_pcm_t *playback_handle_right;
snd_pcm_t *capture_handle_right;
char* crdevice = "VINR";
char* prdevice = "VOUTR";// char* cldevice = "VINL";
// char* pldevice = "VOUTL";
unsigned int rate = 48000; unsigned int nchannels = 1; snd_pcm_format_t format = SND_PCM_FORMAT_S16_LE; unsigned int buf_frames_right = BUF_BYTES / nchannels / 2;
// unsigned int buf_frames_left = BUF_BYTES / nchannels / 2;
///// RIGHT CHANNEL
if ((err = snd_pcm_open (&playback_handle_right, prdevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback right audio device %s (%s)\n", prdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback right audio device successfully %s \n", prdevice);
}
if ((err = snd_pcm_set_params(playback_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback right open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_right, crdevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture right audio device %s (%s)\n", crdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture right audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture right open error: %s\n", snd_strerror(err)); exit(1);
}
#if 0
////LEFT CHANNEL
if ((err = snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback left audio device %s (%s)\n", pldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback left audio device successfully %s \n", pldevice);
}
if ((err = snd_pcm_set_params(playback_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback left open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_left, cldevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture left audio device %s (%s)\n", cldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture left audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture left open error: %s\n", snd_strerror(err)); exit(1);
}#endif
while(1) {
///// RIGHT CHANNEL
if ((err = snd_pcm_readi (capture_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
#if 0
////LEFT CHANNEL
if ((err = snd_pcm_readi (capture_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "read from audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "write to audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
#endif
}
fprintf (stderr, "close handles\n");
snd_pcm_close (playback_handle_right);
snd_pcm_close (capture_handle_right);// snd_pcm_close (playback_handle_left);
// snd_pcm_close (capture_handle_left);
return 0;
}
# default Arago configuration
pcm.card0 {
type hw
card 0
}ctl.card0 {
type hw
card 0
}
pcm.VOUTR {
slave.pcm card0
slave.channels 2
# type plug
type route
ttable {
# Copy both input channels to output channel 0 (Left).
0.0 1
1.1 1
# Send nothing to output channel 1 (Right).
0.1 0
1.1 0 }
}
ctl.VOUTR {
type hw
card 0
}
pcm.VOUTL {
slave.pcm card0
slave.channels 2
# type plug
type route
ttable {
# Send nothing to output channel 0 (Left).
0.1 1
0.1 1
# Copy both input channels to output channel 1 (Right).
0.0 0
1.1 0 }
}
ctl.VOUTL {
type hw
card 0
}
### Dsnoop splited channels
pcm.VINL {
type dsnoop
ipc_key 32
slave {
pcm "card0"
channels 2
}
bindings.0 0
}pcm.VINR {
type dsnoop
ipc_key 32
slave {
pcm "card0"
channels 2
}
bindings.0 1
}### PLUGS ##
### used with darkice
### device = plug:plug_onboard_left
#pcm.plug_VINR{
# type route
# slave.pcm "VINR"
# slave.channels 1
# ttable.0.0 1
#}
#pcm.plug_VINL{
# type route
# slave.pcm "VINL"
# slave.channels 1
# ttable.0.0 1
#}
pcm.!default VOUTR
pcm.!default VOUTL
Quoted 4 lines · Srinivasan S
Could you please provide any inputs w.r.t the loopback card using snd-aloop & alsaloop, how this loopback card can be used to connect the GSM two way call simultanoeusly to the UDA1345TS codec on MCASP0 of the am335x (UDA1345TS ie., real sound card)
snd-aloop creates a virtual sound card; it is not used with a real sound card.
Quoted 4 lines
The codec has two output channels VOUTL, VOUTR & two input channels VINL , VINR
With this am able to achieve only one way call at a time by running only one application at a time
To allow a capture device to be shared, you need to use dsnoop. Your asound.conf already does this.
To allow a playback device to be shared, you need to use dshare or dmix. (dshare allows to use _different_ channels; dmix allows mixing multiple sources into the same channels.) Your asound.conf does not do this; it uses "hw" instead.
Regards,
Clemens
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): 1425964490006.15084-Ig93jE4/[email protected]
Quoted 3 lines · Srinivasan S
$ aplay -f dat -D VOUTL new.wav Playing WAVE 'new.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo aplay: set_params:1087: Channels count non available
You are trying to play a two-channel file on a single-channel device.
Regards,
Clemens
Dear Clemens,
Thanks a lot for your inputs w.r.t the below issue, Now I tried playing 48Khz mono that works fine,
Could you please clarify the following points
1) CPU consumption is 18%, with above asound.conf & the app alsa_loopback_min_mono.c for establishing my GSM two way call (ie., VINR to VOUTR & VINL to VOUTL) , this is very huge & I want to reduce this CPU consumption drastically, Is there any other ways in alsa where I can do this two way GSM call (ie., VINR to VOUTR & VINL to VOUTL) without using alsa_loopback_min_mono.c application
Could you please let me know if there is anything that can be done in using alsa plugins in order to reduce CPU consumption???
2) And am hearing echo, when I do GSM calls when using the above attachd asound.conf & the app alsa_loopback_min_mono.c, could you please help me out is there any options to do echo cancellation in alsa??
3)Am trying to completely understand the above attched asound.conf, but am not still very clear w.r.t the understanding of bindings in alsa plugins as am confused, Could you please clarify the doubt that
i) Does the below lines correspond to VINL to VOUTL or VINL to VOUTR??
bindings {
0 1
}ii) & similarly does the below lines correspond VINL to VOUTL??
bindings {
0 0
}iii) similarly does the correspond VINL to VOUTL??
bindings.0 0
iv) similarly does the correspond VINL to VOUTR or VINR to VOUTR??
bindings.0 1
Kindly do the needful as early as possible, as only this is pending from my side w.r.t AUDIO in my project
Once again really appreciate & Thanks a lot for your prompt responses
Many Many Thanks in advance again,
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Tuesday, March 10, 2015 4:20 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: Fw: [alsa-devel] Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 3 lines · Srinivasan S
$ aplay -f dat -D VOUTL new.wav Playing WAVE 'new.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo aplay: set_params:1087: Channels count non available
You are trying to play a two-channel file on a single-channel device.
Regards,
Clemens
#include <stdio.h>
#include <stdlib.h>
#include <alsa/asoundlib.h>
#define BUF_BYTES 128
int main (/*int argc, char *argv[]*/) {
int err;
unsigned char buf_right[BUF_BYTES];
unsigned char buf_left[BUF_BYTES];
//char *buf;
int size;
snd_pcm_t *playback_handle_right;
snd_pcm_t *capture_handle_right;
snd_pcm_t *playback_handle_left;
snd_pcm_t *capture_handle_left;#if 0 char* device = "default"; if (argc > 1) device = argv[1]; #endif char* crdevice = "VINR"; char* prdevice = "VOUTR"; char* cldevice = "VINL"; char* pldevice = "VOUTL"; unsigned int rate = 48000; unsigned int nchannels = 1; snd_pcm_format_t format = SND_PCM_FORMAT_S16_LE; unsigned int buf_frames_right = BUF_BYTES / nchannels / 2; unsigned int buf_frames_left = BUF_BYTES / nchannels / 2;
///// RIGHT CHANNEL
if ((err = snd_pcm_open (&playback_handle_right, prdevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback right audio device %s (%s)\n", prdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback right audio device successfully %s \n", prdevice);
}
if ((err = snd_pcm_set_params(playback_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback right open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_right, crdevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture right audio device %s (%s)\n", crdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture right audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture right open error: %s\n", snd_strerror(err)); exit(1);
} ////LEFT CHANNEL
if ((err = snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback left audio device %s (%s)\n", pldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback left audio device successfully %s \n", pldevice);
}
if ((err = snd_pcm_set_params(playback_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback left open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_left, cldevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture left audio device %s (%s)\n", cldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture left audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture left open error: %s\n", snd_strerror(err)); exit(1);
}
while(1) {
///// RIGHT CHANNEL
if ((err = snd_pcm_readi (capture_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
////LEFT CHANNEL
if ((err = snd_pcm_readi (capture_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "read from audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "write to audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
}
fprintf (stderr, "close handles\n");
snd_pcm_close (playback_handle_right);
snd_pcm_close (capture_handle_right);
snd_pcm_close (playback_handle_left);
snd_pcm_close (capture_handle_left);
return 0;
} Dear Clemens
Could you please provide any inputs w.r.t the below queries
Kindly do the needful as early as possible
Many Thanks in Advance,
________________________________________
From: Srinivasan S
Sent: Saturday, March 28, 2015 8:13 AM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: Fw: [alsa-devel] Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens,
Thanks a lot for your inputs w.r.t the below issue, Now I tried playing 48Khz mono that works fine,
Could you please clarify the following points
1) CPU consumption is 18%, with above asound.conf & the app alsa_loopback_min_mono.c for establishing my GSM two way call (ie., VINR to VOUTR & VINL to VOUTL) , this is very huge & I want to reduce this CPU consumption drastically, Is there any other ways in alsa where I can do this two way GSM call (ie., VINR to VOUTR & VINL to VOUTL) without using alsa_loopback_min_mono.c application
Could you please let me know if there is anything that can be done in using alsa plugins in order to reduce CPU consumption???
2) And am hearing echo, when I do GSM calls when using the above attachd asound.conf & the app alsa_loopback_min_mono.c, could you please help me out is there any options to do echo cancellation in alsa??
3)Am trying to completely understand the above attched asound.conf, but am not still very clear w.r.t the understanding of bindings in alsa plugins as am confused, Could you please clarify the doubt that
i) Does the below lines correspond to VINL to VOUTL or VINL to VOUTR??
bindings {
0 1
}ii) & similarly does the below lines correspond VINL to VOUTL??
bindings {
0 0
}iii) similarly does the correspond VINL to VOUTL??
bindings.0 0
iv) similarly does the correspond VINL to VOUTR or VINR to VOUTR??
bindings.0 1
Kindly do the needful as early as possible, as only this is pending from my side w.r.t AUDIO in my project
Once again really appreciate & Thanks a lot for your prompt responses
Many Many Thanks in advance again,
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Tuesday, March 10, 2015 4:20 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: Fw: [alsa-devel] Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 3 lines · Srinivasan S
$ aplay -f dat -D VOUTL new.wav Playing WAVE 'new.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo aplay: set_params:1087: Channels count non available
You are trying to play a two-channel file on a single-channel device.
Regards,
Clemens
#include <stdio.h>
#include <stdlib.h>
#include <alsa/asoundlib.h>
#define BUF_BYTES 128
int main (/*int argc, char *argv[]*/) {
int err;
unsigned char buf_right[BUF_BYTES];
unsigned char buf_left[BUF_BYTES];
//char *buf;
int size;
snd_pcm_t *playback_handle_right;
snd_pcm_t *capture_handle_right;
snd_pcm_t *playback_handle_left;
snd_pcm_t *capture_handle_left;#if 0 char* device = "default"; if (argc > 1) device = argv[1]; #endif char* crdevice = "VINR"; char* prdevice = "VOUTR"; char* cldevice = "VINL"; char* pldevice = "VOUTL"; unsigned int rate = 48000; unsigned int nchannels = 1; snd_pcm_format_t format = SND_PCM_FORMAT_S16_LE; unsigned int buf_frames_right = BUF_BYTES / nchannels / 2; unsigned int buf_frames_left = BUF_BYTES / nchannels / 2;
///// RIGHT CHANNEL
if ((err = snd_pcm_open (&playback_handle_right, prdevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback right audio device %s (%s)\n", prdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback right audio device successfully %s \n", prdevice);
}
if ((err = snd_pcm_set_params(playback_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback right open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_right, crdevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture right audio device %s (%s)\n", crdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture right audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture right open error: %s\n", snd_strerror(err)); exit(1);
} ////LEFT CHANNEL
if ((err = snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback left audio device %s (%s)\n", pldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback left audio device successfully %s \n", pldevice);
}
if ((err = snd_pcm_set_params(playback_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback left open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_left, cldevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture left audio device %s (%s)\n", cldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture left audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture left open error: %s\n", snd_strerror(err)); exit(1);
}
while(1) {
///// RIGHT CHANNEL
if ((err = snd_pcm_readi (capture_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
////LEFT CHANNEL
if ((err = snd_pcm_readi (capture_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "read from audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "write to audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
}
fprintf (stderr, "close handles\n");
snd_pcm_close (playback_handle_right);
snd_pcm_close (capture_handle_right);
snd_pcm_close (playback_handle_left);
snd_pcm_close (capture_handle_left);
return 0;
} Could you please provide any inputs w.r.t the below queries
Am awaiting for your suggestions from past 2 to 3 days
Thanks,
Srinivasan S
________________________________________
From: Srinivasan S
Sent: Monday, March 30, 2015 5:10 PM
To: [email protected]
Cc: [email protected]; [email protected]
Subject: Fw: Fw: [alsa-devel] Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens
Could you please provide any inputs w.r.t the below queries
Kindly do the needful as early as possible
Many Thanks in Advance,
________________________________________
From: Srinivasan S
Sent: Saturday, March 28, 2015 8:13 AM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: Fw: [alsa-devel] Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens,
Thanks a lot for your inputs w.r.t the below issue, Now I tried playing 48Khz mono that works fine,
Could you please clarify the following points
1) CPU consumption is 18%, with above asound.conf & the app alsa_loopback_min_mono.c for establishing my GSM two way call (ie., VINR to VOUTR & VINL to VOUTL) , this is very huge & I want to reduce this CPU consumption drastically, Is there any other ways in alsa where I can do this two way GSM call (ie., VINR to VOUTR & VINL to VOUTL) without using alsa_loopback_min_mono.c application
Could you please let me know if there is anything that can be done in using alsa plugins in order to reduce CPU consumption???
2) And am hearing echo, when I do GSM calls when using the above attachd asound.conf & the app alsa_loopback_min_mono.c, could you please help me out is there any options to do echo cancellation in alsa??
3)Am trying to completely understand the above attched asound.conf, but am not still very clear w.r.t the understanding of bindings in alsa plugins as am confused, Could you please clarify the doubt that
i) Does the below lines correspond to VINL to VOUTL or VINL to VOUTR??
bindings {
0 1
}ii) & similarly does the below lines correspond VINL to VOUTL??
bindings {
0 0
}iii) similarly does the correspond VINL to VOUTL??
bindings.0 0
iv) similarly does the correspond VINL to VOUTR or VINR to VOUTR??
bindings.0 1
Kindly do the needful as early as possible, as only this is pending from my side w.r.t AUDIO in my project
Once again really appreciate & Thanks a lot for your prompt responses
Many Many Thanks in advance again,
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Tuesday, March 10, 2015 4:20 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: Fw: [alsa-devel] Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 3 lines · Srinivasan S
$ aplay -f dat -D VOUTL new.wav Playing WAVE 'new.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo aplay: set_params:1087: Channels count non available
You are trying to play a two-channel file on a single-channel device.
Regards,
Clemens
#include <stdio.h>
#include <stdlib.h>
#include <alsa/asoundlib.h>
#define BUF_BYTES 128
int main (/*int argc, char *argv[]*/) {
int err;
unsigned char buf_right[BUF_BYTES];
unsigned char buf_left[BUF_BYTES];
//char *buf;
int size;
snd_pcm_t *playback_handle_right;
snd_pcm_t *capture_handle_right;
snd_pcm_t *playback_handle_left;
snd_pcm_t *capture_handle_left;#if 0 char* device = "default"; if (argc > 1) device = argv[1]; #endif char* crdevice = "VINR"; char* prdevice = "VOUTR"; char* cldevice = "VINL"; char* pldevice = "VOUTL"; unsigned int rate = 48000; unsigned int nchannels = 1; snd_pcm_format_t format = SND_PCM_FORMAT_S16_LE; unsigned int buf_frames_right = BUF_BYTES / nchannels / 2; unsigned int buf_frames_left = BUF_BYTES / nchannels / 2;
///// RIGHT CHANNEL
if ((err = snd_pcm_open (&playback_handle_right, prdevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback right audio device %s (%s)\n", prdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback right audio device successfully %s \n", prdevice);
}
if ((err = snd_pcm_set_params(playback_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback right open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_right, crdevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture right audio device %s (%s)\n", crdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture right audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture right open error: %s\n", snd_strerror(err)); exit(1);
} ////LEFT CHANNEL
if ((err = snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback left audio device %s (%s)\n", pldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback left audio device successfully %s \n", pldevice);
}
if ((err = snd_pcm_set_params(playback_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback left open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_left, cldevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture left audio device %s (%s)\n", cldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture left audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, 500000)) < 0) { /* 0.5sec */
fprintf(stderr, "capture left open error: %s\n", snd_strerror(err)); exit(1);
}
while(1) {
///// RIGHT CHANNEL
if ((err = snd_pcm_readi (capture_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_right, buf_right, buf_frames_right)) != buf_frames_right) {
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err)); exit (1);
}
////LEFT CHANNEL
if ((err = snd_pcm_readi (capture_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "read from audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
if ((err = snd_pcm_writei (playback_handle_left, buf_left, buf_frames_left)) != buf_frames_left) {
fprintf (stderr, "write to audio interface left failed (%s)\n", snd_strerror (err)); exit (1);
}
}
fprintf (stderr, "close handles\n");
snd_pcm_close (playback_handle_right);
snd_pcm_close (capture_handle_right);
snd_pcm_close (playback_handle_left);
snd_pcm_close (capture_handle_left);
return 0;
} A message that is not in the archive (sent off-list or not yet received): 1427510661706.37789-Ig93jE4/[email protected]
Quoted 6 lines · Srinivasan S
CPU consumption is 18%, with above asound.conf & the app
alsa_loopback_min_mono.cfor establishing my GSM two way call (ie., VINR to VOUTR & VINL to VOUTL) , this is very huge & I want to reduce this CPU consumption drastically, Is there any other ways in alsa where I can do this two way GSM call (ie., VINR to VOUTR & VINL to VOUTL) without usingalsa_loopback_min_mono.capplication
dmix needs more CPU than dshare because it needs to mix multiple streams together; if possible, use dshare instead of dmix.
dshare needs more CPU than direct access to the device because the data needs to be copied and reformatted. dshare is needed only when the application(s) cannot handle the format of the actual device; if possible, change your application to handle the two-channel devices.
Quoted 3 lines
And am hearing echo, when I do GSM calls when using the above attachd asound.conf & the app
alsa_loopback_min_mono.c, could you please help me out is there any options to do echo cancellation in alsa?
ALSA has not built-in echo cancellation. You have to implement this yourself, or use some third-party library.
If dmix/dshare alone eats 18 % CPU, it is unlikely that this is feasible without hardware support.
Quoted 2 lines
Am trying to completely understand the above attched asound.conf, but am not still very clear w.r.t the understanding of bindings
"bindings.x y" or "bindings { x y }" maps channel x of this device to channel y of the slave device.
Regards,
Clemens
Thanks a lot for your Prompt responses Clemens
Extremely sorry for my poor understanding,
Could you please clarify the following
1. As per your suggestions below, I didn't understand what is 'two channel devices' does this means do we need to have to real hardware sound card's (ie., two different audio codecs)??? whereas as of now am using only one audio codec( ie., UDA1345TS), if not could you please help me out how to use two channel devices using alsa api's in application or any references for the same???
2. Regarding bindings as you explained"bindings.x y" or "bindings { x y }" maps channel x of this device to channel y of the slave device.
I didn't understand channel x of this device means is it the real sound card??? which is the current device ie., channel x of this device means???
I didn't understand channel y of the slave device means??.. ie., which is slave device here????
Kindly do the needful as early as possible
Awaiting for your replies
Many Thanks in advance
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Thursday, April 2, 2015 3:13 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 6 lines · Srinivasan S
CPU consumption is 18%, with above asound.conf & the app
alsa_loopback_min_mono.cfor establishing my GSM two way call (ie., VINR to VOUTR & VINL to VOUTL) , this is very huge & I want to reduce this CPU consumption drastically, Is there any other ways in alsa where I can do this two way GSM call (ie., VINR to VOUTR & VINL to VOUTL) without usingalsa_loopback_min_mono.capplication
dmix needs more CPU than dshare because it needs to mix multiple streams together; if possible, use dshare instead of dmix.
dshare needs more CPU than direct access to the device because the data needs to be copied and reformatted. dshare is needed only when the application(s) cannot handle the format of the actual device; if possible, change your application to handle the two-channel devices.
Quoted 3 lines
And am hearing echo, when I do GSM calls when using the above attachd asound.conf & the app
alsa_loopback_min_mono.c, could you please help me out is there any options to do echo cancellation in alsa?
ALSA has not built-in echo cancellation. You have to implement this yourself, or use some third-party library.
If dmix/dshare alone eats 18 % CPU, it is unlikely that this is feasible without hardware support.
Quoted 2 lines
Am trying to completely understand the above attched asound.conf, but am not still very clear w.r.t the understanding of bindings
"bindings.x y" or "bindings { x y }" maps channel x of this device to channel y of the slave device.
Regards,
Clemens
Quoted 1 line · Srinivasan S
I didn't understand what is 'two channel devices' does
The two channels are "left" and "right".
Quoted 6 lines
Regarding bindings as you explained"bindings.x y" or "bindings { x y }" maps channel x of this device to channel y of the slave device.
I didn't understand channel x of this device means is it the real sound card??? which is the current device ie., channel x of this device means???
I didn't understand channel y of the slave device means??.. ie., which is slave device here????
"This device" is the virtual device that is defined.
The slave device is the device whose name is specified with "slave.pcm".
Regards,
Clemens
Dear Clemens,
Thanks a lot for your information, It is really understandable for a newbie like me
As you suggested, could you please provide me some sample application links without using dshare plugin , ie., using the two channels ie., left & right directly
So that I can reduce the CPU consumption drastically
Thanks a lot for your prompt support w.r.t this thread once again
Kindly do the needful as early as possible
Many Thanks in advance again
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Thursday, April 2, 2015 8:38 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 1 line · Srinivasan S
I didn't understand what is 'two channel devices' does
The two channels are "left" and "right".
Quoted 6 lines
Regarding bindings as you explained"bindings.x y" or "bindings { x y }" maps channel x of this device to channel y of the slave device.
I didn't understand channel x of this device means is it the real sound card??? which is the current device ie., channel x of this device means???
I didn't understand channel y of the slave device means??.. ie., which is slave device here????
"This device" is the virtual device that is defined.
The slave device is the device whose name is specified with "slave.pcm".
Regards,
Clemens
Dear Clemens,
Could you please provide any inputs or suggestions w.r.t the below query
Kindly do the needful as early as possible,
Many Thanks in advance,
________________________________________
From: Srinivasan S
Sent: Wednesday, April 22, 2015 11:41 AM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens,
Thanks a lot for your information, It is really understandable for a newbie like me
As you suggested, could you please provide me some sample application links without using dshare plugin , ie., using the two channels ie., left & right directly
So that I can reduce the CPU consumption drastically
Thanks a lot for your prompt support w.r.t this thread once again
Kindly do the needful as early as possible
Many Thanks in advance again
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Thursday, April 2, 2015 8:38 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 1 line · Srinivasan S
I didn't understand what is 'two channel devices' does
The two channels are "left" and "right".
Quoted 6 lines
Regarding bindings as you explained"bindings.x y" or "bindings { x y }" maps channel x of this device to channel y of the slave device.
I didn't understand channel x of this device means is it the real sound card??? which is the current device ie., channel x of this device means???
I didn't understand channel y of the slave device means??.. ie., which is slave device here????
"This device" is the virtual device that is defined.
The slave device is the device whose name is specified with "slave.pcm".
Regards,
Clemens
Dear Clemens,
Could you please provide any inputs or suggestions w.r.t the below query
Kindly do the needful as early as possible,
Many Thanks in advance,
________________________________________
From: [email protected] <[email protected]> on behalf of Srinivasan S <[email protected]>
Sent: Wednesday, April 22, 2015 11:41 AM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens,
Thanks a lot for your information, It is really understandable for a newbie like me
As you suggested, could you please provide me some sample application links without using dshare plugin , ie., using the two channels ie., left & right directly
So that I can reduce the CPU consumption drastically
Thanks a lot for your prompt support w.r.t this thread once again
Kindly do the needful as early as possible
Many Thanks in advance again
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Thursday, April 2, 2015 8:38 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 1 line · Srinivasan S
I didn't understand what is 'two channel devices' does
The two channels are "left" and "right".
Quoted 6 lines
Regarding bindings as you explained"bindings.x y" or "bindings { x y }" maps channel x of this device to channel y of the slave device.
I didn't understand channel x of this device means is it the real sound card??? which is the current device ie., channel x of this device means???
I didn't understand channel y of the slave device means??.. ie., which is slave device here????
"This device" is the virtual device that is defined.
The slave device is the device whose name is specified with "slave.pcm".
Regards,
Clemens
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
A message that is not in the archive (sent off-list or not yet received): 1429683117651.11394-Ig93jE4/[email protected]
Quoted 3 lines · Srinivasan S
could you please provide me some sample application links without using dshare plugin , ie., using the two channels ie., left & right directly
I am not aware of any (sample) program that does something like this (except maybe Jack, but floating-point samples would not be appropriate for your application).
You have to implement this yourself.
Regards,
Clemens
Thanks a lot for your quick responses Clemens,
Sorry for my poor understanding
As am newbie to alsa, due to time constraints am unable to spend time in writing my own application
As per your suggestion, did you mean that , If I use Jack plugin , does it resolve this problem (ie., does the CPU consumption reduce drastically instead of dshare)
Kindly do the needful
Once again Thanks a lot for your suggestions Clemens w.r.t this Thread
Thanks in advance,
Srinivasan S
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Friday, April 24, 2015 1:36 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 3 lines · Srinivasan S
could you please provide me some sample application links without using dshare plugin , ie., using the two channels ie., left & right directly
I am not aware of any (sample) program that does something like this (except maybe Jack, but floating-point samples would not be appropriate for your application).
You have to implement this yourself.
Regards,
Clemens
A message that is not in the archive (sent off-list or not yet received): 1429877130444.23317-Ig93jE4/[email protected]
Quoted 3 lines · Srinivasan S
did you mean that , If I use Jack plugin , does it resolve this problem (ie., does the CPU consumption reduce drastically instead of dshare)
It is unlikely that running your two programs on top of Jack will use less CPU than with dshare. However, I don't know the details of your architecture, so the only way to find out would be for you to try it.
Regards,
Clemens
Dear Clemens,
As you suggested am using jack plugin, but am facing the below error
etc/asound.conf
pcm.!default {
type plug
slave { pcm "jack" }
}pcm.jack {
type jack
playback_ports {
0 alsa_pcm:playback_1
1 alsa_pcm:playback_2
}
capture_ports {
0 alsa_pcm:capture_1
1 alsa_pcm:capture_2
}
}ctl.mixer0 {
type hw
card 0
}
root@am335x-evm:/# aplay -D pcm.jack TangoForTajMusic11.wav ALSA lib /home/jenkins/amsdk-nightly-build/build-CORTEX_1/arago-tmp-external-linaro-toolchain/work/cortexa8t2hf-vfp-neon-oe-linux-gnueabi/alsa-lib/1.0.27.2-r0/alsa-lib-1.0.27.2/src/pcm/pcm.c:2239:(snd_pcm_open_noupdate) Unknown PCM pcm.jack aplay: main:722: audio open error: No such file or directory root@am335x-evm:/#
Pls find the details of the architecture as below:
what ever the GSM analog audio out data is pumped as VINR to stereo codec & the output of the stereo codec ie., VOUTR is pumped to the Speaker of the custom board
what ever the GSM analog audio out data is pumped as VINR to stereo codec & the output of the stereo codec ie., VOUTR is pumped to the Speaker of the custom board GSM MIC-> VINR -> stereo codec->VOUTR -> board speaker
what ever the board MIC data is pumped as VINL to stereo codec & the output of the stereo codec ie., VOUTL is pumped as analog input to the GSM Speaker Board Mic -> VINL-> stereo codec -> VOUTL ->GSM speaker
Pls let me know if any other details is required from my side
Kindly do the needful as early as possible
Awaiting for your suggestions
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Friday, April 24, 2015 6:15 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 3 lines · Srinivasan S
did you mean that , If I use Jack plugin , does it resolve this problem (ie., does the CPU consumption reduce drastically instead of dshare)
It is unlikely that running your two programs on top of Jack will use less CPU than with dshare. However, I don't know the details of your architecture, so the only way to find out would be for you to try it.
Regards,
Clemens
Dear Clemens
Could you please help me in converting the above asound.conf to jack plugin by providing some tips
1. Pls find the details of the architecture as below:
what ever the GSM analog audio out data is pumped as VINR to stereo codec & the output of the stereo codec ie., VOUTR is pumped to the Speaker of the custom board
what ever the GSM analog audio out data is pumped as VINR to stereo codec & the output of the stereo codec ie., VOUTR is pumped to the Speaker of the custom board GSM MIC-> VINR -> stereo codec->VOUTR -> board speaker
what ever the board MIC data is pumped as VINL to stereo codec & the output of the stereo codec ie., VOUTL is pumped as analog input to the GSM Speaker Board Mic -> VINL-> stereo codec -> VOUTL ->GSM speaker
2. Could you please let me know, I have downloaded jack-1.9.10.tar.bz2, how this needs to be installed in my rootfs
Pls let me know if any other details is required from my side
Thanks,
Srinivasan S
________________________________________
From: [email protected] <[email protected]> on behalf of Srinivasan S <[email protected]>
Sent: Friday, May 29, 2015 4:50 PM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens,
As you suggested am using jack plugin, but am facing the below error
etc/asound.conf
pcm.!default {
type plug
slave { pcm "jack" }
}pcm.jack {
type jack
playback_ports {
0 alsa_pcm:playback_1
1 alsa_pcm:playback_2
}
capture_ports {
0 alsa_pcm:capture_1
1 alsa_pcm:capture_2
}
}ctl.mixer0 {
type hw
card 0
}
root@am335x-evm:/# aplay -D pcm.jack TangoForTajMusic11.wav ALSA lib /home/jenkins/amsdk-nightly-build/build-CORTEX_1/arago-tmp-external-linaro-toolchain/work/cortexa8t2hf-vfp-neon-oe-linux-gnueabi/alsa-lib/1.0.27.2-r0/alsa-lib-1.0.27.2/src/pcm/pcm.c:2239:(snd_pcm_open_noupdate) Unknown PCM pcm.jack aplay: main:722: audio open error: No such file or directory root@am335x-evm:/#
Pls find the details of the architecture as below:
what ever the GSM analog audio out data is pumped as VINR to stereo codec & the output of the stereo codec ie., VOUTR is pumped to the Speaker of the custom board
what ever the GSM analog audio out data is pumped as VINR to stereo codec & the output of the stereo codec ie., VOUTR is pumped to the Speaker of the custom board GSM MIC-> VINR -> stereo codec->VOUTR -> board speaker
what ever the board MIC data is pumped as VINL to stereo codec & the output of the stereo codec ie., VOUTL is pumped as analog input to the GSM Speaker Board Mic -> VINL-> stereo codec -> VOUTL ->GSM speaker
Pls let me know if any other details is required from my side
Kindly do the needful as early as possible
Awaiting for your suggestions
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Friday, April 24, 2015 6:15 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 3 lines · Srinivasan S
did you mean that , If I use Jack plugin , does it resolve this problem (ie., does the CPU consumption reduce drastically instead of dshare)
It is unlikely that running your two programs on top of Jack will use less CPU than with dshare. However, I don't know the details of your architecture, so the only way to find out would be for you to try it.
Regards,
Clemens
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
A message that is not in the archive (sent off-list or not yet received): HKXPR04MB277B58064C140058C37487EC3B60-T1ls2vrYf5VLAZUorM51PQfhPeD8jYilXA4E9RH9d+qIuWR1G4zioA@public.gmane.org
Quoted 1 line · Srinivasan S
2. Could you please let me know, I have downloaded jack-1.9.10.tar.bz2, how this needs to be installed in my rootfs
IIRC Jack uses some non-standard build system. Try asking on the Jack mailing list how to cross-compile it.
Please note that the ALSA Jack plugin is part of the alsa-plugins package.
And as I already mentioned, it is unlikely that Jack will use less CPU than dshare.
Regards,
Clemens
Dear Clemens
As I didn't find Jack mailing lists by googling, could you please loop Jack mailing lists to this mail chain
Kindly do the needful as early as possible
Many Thanks in advance
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Monday, June 1, 2015 8:09 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 1 line · Srinivasan S
2. Could you please let me know, I have downloaded jack-1.9.10.tar.bz2, how this needs to be installed in my rootfs
IIRC Jack uses some non-standard build system. Try asking on the Jack mailing list how to cross-compile it.
Please note that the ALSA Jack plugin is part of the alsa-plugins package.
And as I already mentioned, it is unlikely that Jack will use less CPU than dshare.
Regards,
Clemens
A message that is not in the archive (sent off-list or not yet received): SIXPR04MB2530654AB664B2CE19B4665C3A80@SIXPR04MB253.apcprd04.prod.outlook.com
Dear Clemens,
Many Thanks a lot for all your support w.r.t this thread so far
Am facing overrun & underrun issues, when I run the the above GSM application with the attached asound.conf
I have some understanding by googling & found why this overrun & underrun issues occurs ie., unable to transfer audio frames from hardware buffers to application buffers(for capture) & the viceversa(for playback),
As I googled, I didn't get detailed information with bits & pieces here & there, could you please help me out in resolving this overrun & underrun issue ie., how to set this buffer size or only buffer_size is causing this issue or any other parameters like period_size, period_time values should also be considered inorder to fix this overrun & underrun issue
Now I have randomly set the buffer size ie., 4097 for 8Khz sampling rate
But I have no idea logically how this buffer size 4097 is working for 8Khz & when I copied the same buffer size to 48Khz, the audio gets cut & again overrun & underrun issue is seen
Could you please help me out how to fix this overrun & underrun issue logically, rather than I have that an understanding of programming some random values like 4097
Is it possible to fix this issue in asound.conf itself, rather than using multithreading in GSM application
So that fixing these types of issues henceforth will be faster & addressed logically & will be helpful for others as well
Kindly do the needful as early as possible
Many Thanks in advance once again
________________________________________
From: Srinivasan S
Sent: Wednesday, July 1, 2015 12:54 PM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens,
Many Thanks a lot for all your support w.r.t this thread so far
Am facing overrun & underrun issues on TI AM335x, when I run the the above GSM application with the attached asound.conf
I have some understanding by googling & found why this overrun & underrun issues occurs ie., unable to transfer audio frames from hardware buffers to application buffers(for capture) & the viceversa(for playback),
As I googled, I didn't get detailed information with bits & pieces here & there, could you please help me out in resolving this overrun & underrun issue ie., how to set this buffer size or only buffer_size is causing this issue or any other parameters like period_size, period_time values should also be considered inorder to fix this overrun & underrun issue
Now I have randomly set the buffer size ie., 4097 for 8Khz sampling rate
But I have no idea logically how this buffer size 4097 is working for 8Khz & when I copied the same buffer size to 48Khz, the audio gets cut & again overrun & underrun issue is seen
Could you please help me out how to fix this overrun & underrun issue logically, rather than I have that an understanding of programming some random values like 4097
Is it possible to fix this issue in asound.conf itself, rather than using multithreading in GSM application
So that fixing these types of issues henceforth will be faster & addressed logically & will be helpful for others as well
Kindly do the needful as early as possible
Many Thanks in advance once again
________________________________________
From: [email protected] <[email protected]> on behalf of Srinivasan S <[email protected]>
Sent: Wednesday, June 3, 2015 11:35 AM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens
As I didn't find Jack mailing lists by googling, could you please loop Jack mailing lists to this mail chain
Kindly do the needful as early as possible
Many Thanks in advance
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Monday, June 1, 2015 8:09 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 1 line · Srinivasan S
2. Could you please let me know, I have downloaded jack-1.9.10.tar.bz2, how this needs to be installed in my rootfs
IIRC Jack uses some non-standard build system. Try asking on the Jack mailing list how to cross-compile it.
Please note that the ALSA Jack plugin is part of the alsa-plugins package.
And as I already mentioned, it is unlikely that Jack will use less CPU than dshare.
Regards,
Clemens
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
#include <stdio.h>
#include <stdlib.h>
#include <alsa/asoundlib.h>
#define BUF_BYTES 128
int main (int argc, char *argv[]) {
int err, rc ; unsigned char buf_right[BUF_BYTES]; unsigned char buf_left[BUF_BYTES]; //char *buf; int size; snd_pcm_t *playback_handle_right; snd_pcm_t *capture_handle_right; snd_pcm_t *playback_handle_left; snd_pcm_t *capture_handle_left;
#if 0
char* device = "default";
if (argc > 1) device = argv[1];
#endif
char* crdevice ;
char* prdevice ;
char* cldevice ;
char* pldevice ;
unsigned int rate ;
unsigned int latancy;
unsigned int nchannels = 1;
snd_pcm_format_t format = SND_PCM_FORMAT_S16_LE;
unsigned int buf_frames_right = BUF_BYTES / nchannels / 2;
unsigned int buf_frames_left = BUF_BYTES / nchannels / 2;
if(argc != 3 )
{
printf("\nUsage is : application sampling_rate latancy \n\n\t Ex: ./gsm_application_target 8000 \n\n\t Supported sampling rates are: \n\t 1) 8000 \n\t 2) 16000 \n\t 3) 32000 \n\t 4) 44100 \n\t 5) 48000 \n\n NOTE: Any number other than given sampling rate takes default as 48000\n\n");
exit(1);
}
rate = (int)atoi(argv[1]);
latancy = (int)atoi(argv[2]);
if(rate == 8000)
{
crdevice = "VINR8";
prdevice = "VOUTL8";
cldevice = "VINL8";
pldevice = "VOUTR8";
}else if(rate == 16000)
{
crdevice = "VINR16";
prdevice = "VOUTR16";
cldevice = "VINL16";
pldevice = "VOUTL16";
}else if(rate == 32000)
{
crdevice = "VINR32";
prdevice = "VOUTR32";
cldevice = "VINL32";
pldevice = "VOUTL32";
}else if(rate == 44100)
{
crdevice = "VINR44";
prdevice = "VOUTR44";
cldevice = "VINL44";
pldevice = "VOUTL44";
}else
{
crdevice = "VINR48";
prdevice = "VOUTL48";
cldevice = "VINL48";
pldevice = "VOUTR48";
rate = 48000;
}///// RIGHT CHANNEL
newStart:
if ((err = snd_pcm_open (&playback_handle_right, prdevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback right audio device %s (%s)\n", prdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback right audio device successfully %s \n", prdevice);
}
if ((err = snd_pcm_set_params(playback_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, latancy)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback right open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_right, crdevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture right audio device %s (%s)\n", crdevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture right audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_right, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, latancy)) < 0) { /* 0.5sec */
fprintf(stderr, "capture right open error: %s\n", snd_strerror(err)); exit(1);
} ////LEFT CHANNEL
if ((err = snd_pcm_open (&playback_handle_left, pldevice, SND_PCM_STREAM_PLAYBACK, 0)) < 0) {
fprintf (stderr, "cannot open playback left audio device %s (%s)\n", pldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Playback left audio device successfully %s \n", pldevice);
}
if ((err = snd_pcm_set_params(playback_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, latancy)) < 0) { /* 0.5sec */
fprintf(stderr, "Playback left open error: %s\n", snd_strerror(err)); exit(1);
}
if ((err = snd_pcm_open (&capture_handle_left, cldevice, SND_PCM_STREAM_CAPTURE, 0)) < 0) {
fprintf (stderr, "cannot open capture left audio device %s (%s)\n", cldevice, snd_strerror (err)); exit (1);
}
else
{
printf("Opened Capture left audio device successfully %s \n", crdevice);
}
if ((err = snd_pcm_set_params(capture_handle_left, format, SND_PCM_ACCESS_RW_INTERLEAVED, nchannels, rate, 1, latancy)) < 0) { /* 0.5sec */
fprintf(stderr, "capture left open error: %s\n", snd_strerror(err)); exit(1);
}
while(1) {
///// RIGHT CHANNEL
/***** Read the Frames from the Capture Device ******/
snd_pcm_prepare(capture_handle_right);
err = snd_pcm_readi(capture_handle_right, buf_right, buf_frames_right);
if(err < 0)
{
printf("capture right func: overrun!");
rc = snd_pcm_prepare(capture_handle_right);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
}
}
if(err < 0)
{
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err));
rc = snd_pcm_recover(capture_handle_right,err,0);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
goto reStart;
}
}else if(err != (int)buf_frames_right)
{
fprintf(stderr, "short read, read %d frames\n", err);
}
snd_pcm_prepare(playback_handle_right);
/**** Write the capture frame to playback ******/
err = snd_pcm_writei (playback_handle_right, buf_right, buf_frames_right);
if(err == -EPIPE)
{
printf("Playback right func: overrun!");
rc = snd_pcm_prepare(playback_handle_right);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
}
}
if(err < 0)
{
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err));
rc = snd_pcm_recover(playback_handle_right, err, 0);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
goto reStart;
}
}else if(err != (int)buf_frames_right)
{
fprintf(stderr, "short write, write %d frames\n", err);
}////LEFT CHANNEL
snd_pcm_prepare(capture_handle_left);
/***** Read the Frames from the Capture Device ******/
err = snd_pcm_readi(capture_handle_left, buf_left, buf_frames_left);
if(err == -EPIPE)
{
printf("capture right func: overrun!");
rc = snd_pcm_prepare(capture_handle_left);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
}
}
if(err < 0)
{
fprintf (stderr, "read from audio interface right failed (%s)\n", snd_strerror (err));
rc = snd_pcm_recover(capture_handle_left,err,0);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
goto reStart;
}
}else if(err != (int)buf_frames_left)
{
fprintf(stderr, "short read, read %d frames\n", err);
}
snd_pcm_prepare(playback_handle_left);
/**** Write the capture frame to playback ******/
err = snd_pcm_writei (playback_handle_left, buf_left, buf_frames_left);
if(err == -EPIPE)
{
printf("Playback right func: overrun!");
rc = snd_pcm_prepare(playback_handle_left);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
goto reStart;
}
}
if(err < 0)
{
fprintf (stderr, "write to audio interface right failed (%s)\n", snd_strerror (err));
rc = snd_pcm_recover(playback_handle_left, err, 0);
if(rc < 0)
{
printf("Fail to recover from problem, Need to reopen the device\n");
goto reStart;
}
}else if(err != (int)buf_frames_left)
{
fprintf(stderr, "short write, write %d frames\n", err);
}
}reStart: fprintf (stderr, "close handles\n");
snd_pcm_close (playback_handle_right);
snd_pcm_close (capture_handle_right);
snd_pcm_close (playback_handle_left);
snd_pcm_close (capture_handle_left);
sleep(2);
goto newStart;
return 0;
} A message that is not in the archive (sent off-list or not yet received): SIXPR04MB2531DB716093D09C156BEA0C3A80-gTWnircbfuxAKSrPHYfF6gfhPeD8jYilXA4E9RH9d+qIuWR1G4zioA@public.gmane.org
Quoted 1 line · Srinivasan S
Am facing overrun & underrun issues, when I run the the above GSM application with the attached asound.conf
The sound card and the GSM streams are not synchronized.
You need to compensate for the drift between the clocks, typically by resampling. (Jack's alsa_in/alsa_out would automatically do this.)
Regards,
Clemens
Dear Clemens,
Thanks a lot for your support Clemens
As you suggested, When I try to use alsa jack plugin, am facing the below error
root@lifeline:/# vi etc/asound.conf
pcm.rawjack {
type jack
playback_ports {
0 system:playback_1
1 system:playback_2
}
capture_ports {
0 system:capture_1
1 system:capture_2
}
}pcm.jack {
type plug
slave { pcm "rawjack" }
hint {
description "JACK Audio Connection Kit"
}
}
pcm.!default {
type plug
slave { pcm "rawjack" }
}
root@lifeline:/opt/tunstall/audio# aplay -D pcm.jack TangoForTajMusic11.wav ALSA lib /home/jenkins/amsdk-nightly-build/build-CORTEX_1/arago-tmp-external-linaro-toolchain/work/cortexa8t2hf-vfp-neon-oe-linux-gnueabi/alsa-lib/1.0.27.2-r0/alsa-lib-1.0.27.2/src/dlmisc.c:252:(snd1_dlobj_cache_get) Cannot open shared library /usr/lib/alsa-lib/libasound_module_pcm_jack.so aplay: main:722: audio open error: No such device or address root@lifeline:/opt/tunstall/audio#
I feel order to resolve this error,
1. I feel that there is no libasound_module_pcm_jack.so, I have downloaded the alsa-plugins-1.0.29 could you please help me out how this can be cross compiled for my TI AM335x platform
2. Could you please let me know to cross compile & install the package libasound2-dev
Could you please help me out in resolving this issue
Kindly do the needful as early as possible
Many Thanks a lot for your support once again w.r.t this thread so far
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Wednesday, July 1, 2015 7:41 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 1 line · Srinivasan S
Am facing overrun & underrun issues, when I run the the above GSM application with the attached asound.conf
The sound card and the GSM streams are not synchronized.
You need to compensate for the drift between the clocks, typically by resampling. (Jack's alsa_in/alsa_out would automatically do this.)
Regards,
Clemens
Dear Clemens
Could you please kindly help me out to cross_compile this alsa_plugins, so that I can resolve the below error & & get jack plugins working as you suggested earlier
Many Thanks in advance
Srinivasan S
________________________________________
From: Srinivasan S
Sent: Wednesday, July 8, 2015 8:55 PM
To: Clemens Ladisch
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Dear Clemens,
Thanks a lot for your support Clemens
As you suggested, When I try to use alsa jack plugin, am facing the below error
root@lifeline:/# vi etc/asound.conf
pcm.rawjack {
type jack
playback_ports {
0 system:playback_1
1 system:playback_2
}
capture_ports {
0 system:capture_1
1 system:capture_2
}
}pcm.jack {
type plug
slave { pcm "rawjack" }
hint {
description "JACK Audio Connection Kit"
}
}
pcm.!default {
type plug
slave { pcm "rawjack" }
}
root@lifeline:/opt/tunstall/audio# aplay -D pcm.jack TangoForTajMusic11.wav ALSA lib /home/jenkins/amsdk-nightly-build/build-CORTEX_1/arago-tmp-external-linaro-toolchain/work/cortexa8t2hf-vfp-neon-oe-linux-gnueabi/alsa-lib/1.0.27.2-r0/alsa-lib-1.0.27.2/src/dlmisc.c:252:(snd1_dlobj_cache_get) Cannot open shared library /usr/lib/alsa-lib/libasound_module_pcm_jack.so aplay: main:722: audio open error: No such device or address root@lifeline:/opt/tunstall/audio#
I feel order to resolve this error,
1. I feel that there is no libasound_module_pcm_jack.so, I have downloaded the alsa-plugins-1.0.29 could you please help me out how this can be cross compiled for my TI AM335x platform
2. Could you please let me know to cross compile & install the package libasound2-dev
Could you please help me out in resolving this issue
Kindly do the needful as early as possible
Many Thanks a lot for your support once again w.r.t this thread so far
________________________________________
From: Clemens Ladisch <[email protected]>
Sent: Wednesday, July 1, 2015 7:41 PM
To: Srinivasan S
Cc: [email protected]; [email protected]
Subject: Re: [alsa-devel] Fw: Using loopback card to Connect GSM two way call to the real sound card UDA1345TS
Quoted 1 line · Srinivasan S
Am facing overrun & underrun issues, when I run the the above GSM application with the attached asound.conf
The sound card and the GSM streams are not synchronized.
You need to compensate for the drift between the clocks, typically by resampling. (Jack's alsa_in/alsa_out would automatically do this.)
Regards,
Clemens